Star Manufacturing 824T-LP, 824TS-LP, 824TSCHS-LP, 836M-LP, 836T-LP Operation Manual

...

Star Manufacturing International Inc.

10 Sunnen Drive St. Louis, MO 63143

Phone: (314) 781-2777 Fax: (314) 781-2714

2M-Z7924 Rev. A 3/15/2006

Installation

and

Operating

Instructions

ULTRA-MAX GAS GRIDDLE

MODELS

824M-LP 824T-LP 824TS-LP 824TSCHS-LP 836M-LP 836T-LP 836TS-LP 836TSCHS-LP 848M-LP 848T-LP 848TS-LP 848TSCHS-LP 860M-LP 860T-LP 860TS-LP 860TSCHS-LP 872M-LP 872T-LP 872TS-LP 872TSCHS-LP

WARNING: Improper installation, adjustment, alteration, service or maintenance can cause property damage, injury or death. Read the installation, operating and maintenance instructions thoroughly before installing or servicing this equipment.

FOR YOUR SAFETY: Do not store or use gasoline or other ﬂ ammable vapors or liquids in the vicinity of this or any other appliance.

WARNING: This appliance shall be installed in accordance with current regulations and used only in well-ventilated space. Refer to instructions before installing and using this appliance.

In addition, there should be posted, in a prominent location, detailed instructions to be followed in the event the operator smells gas. Obtain the instructions from the local gas supplier.

SAFETY SYMBOL

Using any part other than genuine Star factory supplied parts relieves the manufacturer of all liability.

Star reserves the right to change speciﬁ cations and product design without notice. Such revisions do not entitle the buyer to corresponding changes, improvements, additions or replacements for previously purchased equipment.

Due to periodic changes in designs, methods, procedures, policies and regulations, the speciﬁ cations contained in this sheet are subject to change without notice. While Star Manufacturing exercises good faith efforts to provide information that is accurate, we are not responsible for errors or omissions in information provided or conclusions reached as a result of using the speciﬁ cations. By using the information provided, the user assumes all risks in connection with such use.

These symbols are intended to alert the user to the presence of important operating and maintenance instructions in the manual accompanying the appliance.

RETAIN THIS MANUAL FOR FUTURE REFERENCE

NOTICE

MAINTENANCE AND REPAIRS

Contact your local authorized service agent for service or required maintenance. Please record the model number, serial number, voltage and purchase date in the area below and have it ready when you call to

ensure a faster service.

Model No.

Serial No.

Voltage

Purchase Date

Authorized Service Agent

Reference the listing provided with the unit

for an updated listing go to:

Website: www.star-mfg.com E-mail Service@star-mfg.com Telephone: (800) 807-9054 Local (314) 781-2777

The Star Service Help Desk

Business 8:00 am to 4:30 p.m. Central Standard Time Hours:

Telephone: (800) 807-9054 Local (314) 781-2777

Fax: (800) 396-2677 Local (314) 781-2714

E-mail Parts@star-mfg.com

Service@star-mfg.com Warranty@star-mfg.com

Website: www.star-mfg.com

Mailing Address: Star Manufacturing International Inc.

10 Sunnen Drive St. Louis, MO 63143 U.S.A

SPECIFICATIONS

824M-LP

Type: Manual Valve

2 Controls, 60,000 BTUH, 573 sq. in. (3697 sq. cm) Grid Area Approximate Weight: Installed - 214 Lb s (97.0 kg), shipping - 244 Lbs (110.6 kg) Dimensions: 24" - Width, 32 3/8" - Depth, 18" - Height (61 cm - Width, 82.2 cm - Depth, 45.7 cm - Height)

836M-LP

Type: Manual Valve

3 Controls, 90,000 BTUH, 860 sq. in. (5545 sq. cm) Grid Area Approximate Weight: Installed - 321 Lbs (145.4 kg), shipping - 366 Lbs (165.8 kg) Dimensions: 36" - Width, 32 3/8" - Depth, 18" - Height (91.4 cm - Width, 82.2 cm - Depth, 45.7 cm - Height)

848M-LP

Type: Manual Valve

4 Controls, 120,000 BTUH, 1146 sq. in. (7394 sq. cm) Grid Area Approximate Weight: Installed - 428 Lbs (193.9 kg), shipping - 488 Lbs (221.1 kg) Dimensions: 48" - Width, 32 3/8" - Depth, 18" - Height (122 cm - Width, 82.2 cm - Depth, 45.7 cm - Height)

860M-LP

Type: Manual Valve

5 Controls, 150,000 BTUH, 1433 sq. in. (9242 sq. cm) Grid Area Approximate Weight: Installed - 535 Lbs (242.4 kg), shipping - 610 Lbs (276.4 kg) Dimensions: 60" - Width, 32 3/8" - Depth, 18" - Height (152.4 cm - Width, 82.2 cm - Depth, 45.7 cm - Height)

872M-LP

Type: Manual Valve

6 Controls, 180,000 BTUH, 1719 sq. in. (11091 sq. cm) Grid Area Approximate Weight: Installed - 642 Lbs (290.9 kg), shipping - 732 Lbs (331.7 kg) Dimensions: 72" - Width, 32 3/8" - Depth, 18" - Height (182.9 cm - Width, 82.2 cm - Depth, 45.7 cm - Height)

824T-LP

Type: Throttling Control

2 Controls, 60,000 BTUH, 573 sq. in. (3697 sq. cm) Grid Area Approximate Weight: Installed - 220 Lb s (99.7 kg), shipping - 246 Lbs (111.5 kg) Dimensions: 24" - Width, 32 3/8" - Depth, 18" - Height (61 cm - Width, 82.2 cm - Depth, 45.7 cm - Height)

836T-LP

Type: Throttling Control

3 Controls, 90,000 BTUH, 860 sq. in. (5545 sq. cm) Grid Area Approximate Weight: Installed - 330 Lbs (149.5 kg), shipping - 369 Lbs (167.2 kg) Dimensions: 36" - Width, 32 3/8" - Depth, 18" - Height (91.4 cm - Width, 82.2 cm - Depth, 45.7 cm - Height)

848T-LP

Type: Throttling Control

4 Controls, 120,000 BTUH, 1146 sq. in. (7394 sq. cm) Grid Area Approximate Weight: Installed - 440 Lbs (199.4 kg), shipping - 492 Lbs (222.9 kg) Dimensions: 48" - Width, 32 3/8" - Depth, 18" - Height (122 cm - Width, 82.2 cm - Depth, 45.7 cm - Height)

860T-LP

Type: Throttling Control

5 Controls, 150,000 BTUH, 1433 sq. in. (9242 sq. cm) Grid Area Approximate Weight: Installed - 550 Lbs (249.2 kg), shipping - 615 Lbs (278.7 kg) Dimensions: 60" - Width, 32 3/8" - Depth, 18" - Height

(152.4 cm - Width, 82.2 cm - Depth, 45.7 cm - Height)

872T-LP

Type: Throttling Control

6 Controls, 180,000 BTUH, 1719 sq. in. (11091 sq. cm) Grid Area Approximate Weight: Installed - 660 Lbs (299.0 kg), shipping - 738 Lbs (334.4 kg) Dimensions: 72" - Width, 32 3/8" - Depth, 18" - Height

(182.9 cm - Width, 82.2 cm - Depth, 45.7 cm - Height)

824TS-LP

Type: Snap Action Control With Safety Pilot

2 Controls, 60,000 BTUH, 573 sq. in. (3697 sq. cm) Grid Area Approximate Weight: Installed - 222 Lb s (100.6 kg), shipping - 250 Lbs (113.3 kg) Dimensions: 24" - Width, 32 3/8" - Depth, 18" - Height (61 cm - Width, 82.2 cm - Depth, 45.7 cm - Height)

836TS-LP

Type: Snap Action Control With Safety Pilot

3 Controls, 90,000 BTUH, 860 sq. in. (5545 sq. cm) Grid Area Approximate Weight: Installed - 333 Lbs (150.9 kg), shipping - 375 Lbs (169.9 kg) Dimensions: 36" - Width, 32 3/8" - Depth, 18" - Height (91.4 cm - Width, 82.2 cm - Depth, 45.7 cm - Height)

848TS-LP

Type:Snap Action Control With Safety Pilot

4 Controls, 120,000 BTUH, 1146 sq. in. (7394 sq. cm) Grid Area Approximate Weight: Installed - 444 Lbs (201.2 kg), shipping - 500 Lbs (226.6 kg) Dimensions: 48" - Width, 32 3/8" - Depth, 18" - Height (122 cm - Width, 82.2 cm - Depth, 45.7 cm - Height)

860TS-LP

Type: Snap Action Control With Safety Pilot

5 Controls, 150,000 BTUH, 1433 sq. in. (9242 sq. cm) Grid Area Approximate Weight: Installed - 555 Lbs (251.5 kg), shipping - 625 Lbs (283.2 kg) Dimensions: 60" - Width, 32 3/8" - Depth, 18" - Height (152.4 cm - Width, 82.2 cm - Depth, 45.7 cm - Height)

872TS-LP

Type: Snap Action Control With Safety Pilot

6 Controls, 180,000 BTUH, 1719 sq. in. (11091 sq. cm) Grid Area Approximate Weight: Installed - 666 Lbs (301.8 kg), shipping - 750 Lbs (339.8 kg) Dimensions: 72" - Width, 32 3/8" - Depth, 18" - Height

(182.9 cm - Width, 82.2 cm - Depth, 45.7 cm - Height)

824TSCHS-LP

Type: Snap Action With Safety Pilot and Chrome Plate 2 Controls, 60,000 BTUH, 573 sq. in. (3697 sq. cm) Grid Area Approximate Weight: Installed - 222 Lb s (100.6 kg), shipping - 250 Lbs (113.3 kg) Dimensions: 24" - Width, 32 3/8" - Depth, 18" - Height (61 cm - Width, 82.2 cm - Depth, 45.7 cm - Height)

836TSCHS-LP

Type: Snap Action Control With Safety Pilot and Chrome Plate

848TSCHS-LP

Type: Snap Action Control With Safety Pilot and Chrome Plate

4 Controls, 120,000 BTUH, 1146 sq. in. (7394 sq. cm) Grid Area Approximate Weight: Installed - 444 Lbs (201.2 kg), shipping - 500 Lbs (226.6 kg) Dimensions: 48" - Width, 32 3/8" - Depth, 18" - Height

(122 cm - Width, 82.2 cm - Depth, 45.7 cm - Height)

860TSCHS-LP

Type: Snap Action Control With Safety Pilot and Chrome Plate

5 Controls, 150,000 BTUH, 1433 sq. in. (9242 sq. cm) Grid Area Approximate Weight: Installed - 555 Lbs (251.5 kg), shipping - 625 Lbs (283.2 kg) Dimensions: 60" - Width, 32 3/8" - Depth, 18" - Height

(152.4 cm - Width, 82.2 cm - Depth, 45.7 cm - Height)

872TSCHS-LP

Type: Snap Action Control With Safety Pilot and Chrome Plate

GENERAL INSTALLATION DATA

NOTICE

CAUTION

This equipment is designed and sold for commercial use only by personnel trained and experienced in its operation and is not sold for consumer use in and around the home nor for use directly by the general public in food service locations.

Ultra-Max series griddles are equipped for use on either natural or propane gas. This unit is shipped for propane gas and can easily be converted to natural.

See Natural Gas - Conversion.

-IMPORTANT-

Be sure to remove all paper protection and packing material from unit prior to lighting. Remove the protective plastic from the griddle plate and thoroughly clean the unit's exterior surfaces.

KEEP THE APPLIANCE AREA FREE AND CLEAR FROM COMBUSTIBLES! For use on

non-combustible countertops only. Combustible and non-combustible material must be at least 48" (120cm) from the top of the appliance and at least 6" (16cm) from the sides and back. Adequate clearance should also be provided for proper operation and servicing.

The installation of the Appliance must conform to the NATIONAL FUEL GAS CODE "ANSI Z223.1 - LATEST EDITION" AND ALL LOCAL GAS COMPANY RULES AND REGULATIONS.

IN CANADA INSTALLATION SHALL BE IN ACCORDANCE WITH THE CURRENT CAN/ CGA-B149.1 NATURAL GAS INSTALLATION CODE OR CAN/CGA-B149.2 PROPANE INSTALLATION CODE AND LOCAL CODES WHERE APPLICABLE.

When this appliance is installed with casters, it must be installed with the casters supplied, a connector complying with either ANSI Z21.69 or CAN/CGA-6.16 and a quick-disconnect device complying with either ANSI Z21.41 or CAN1-6.9. It must also be installed with restraining means to guard against transmission of strain to the connector.

For your protection, we recommend a qualiﬁ ed installing agency install this appliance. They should be familiar with gas installations and your local gas requirements. In any case, your gas company should be called to approve the ﬁ nal

installation.

This appliance, its pressure regulator and its individual shutoff valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures in excess of 1/2 PSIG. This appliance and its pressure regulator must be isolated from the gas supply piping system by closing its individual manual shutoff valve during any pressure testing of the gas supply piping system at test pressures

equal to or less than 1/2 PSIG.

EXHAUST CANOPY

Griddles inherently create a good deal of heat and smoke and should be installed under an efﬁ cient exhaust hood with ﬂ ame proof ﬁ lters. A vertical distance of not less than 48" shall be provided between the top of the appliance and ﬁ lters or any other combustible material. Exhaust installation must conform to local codes.

AIR SUPPLY

Provisions for adequate air supply must be provided.

CAUTION

AIR INTAKES IN BOTTOM

Air for combustion enters from the bottom of the unit.

Do not obstruct this area.

LEVELING UNIT

This griddle is supplied with 4 feet or ﬂ oor stand legs which must be screwed into the body. Unit must be level. Level unit by adjusting the (4) feet which have an adjustment of 1-3/4" for accurate and perfect line-up with other units.

CAUTION

DO NOT INSTALL WITHOUT ATTACHING FEET OR SUPPLIED STAND LEGS AND SHELF - DO NOT REMOVE FEET.

Caster Kits: Casters can be used with ﬂ oor stand models or optional equipment stand. For installation, carefully mark and cut off from the bottom of each leg using a straight cutting saw and de-burr the inside tube wall prior to installing the caster. Cut leg should measure 19" tube length, not overall length. Casters add about 6-1/4" of height to the unit. Be sure to use approved strain relief means for protecting gas line connection. If an appliance is equipped with casters and is gas connected with a quick connect coupling, all personnel must be aware that there is a restraint on the appliance and if disconnected for service or cleaning it must be reconnected as originally installed prior to use.

GAS PIPING

Gas piping shall be of such size and so installed as to provide a supply of gas sufﬁ cient to meet the full gas input of the appliance. If the appliance is to be connected to existing piping, it shall be checked to determine if it has adequate capacity. Joint compound shall be used sparingly and only on the male threads of the pipe joints. Such compounds shall be resistant to the action of L.P. gases. WARNING: Any loose dirt or metal particles which are allowed to enter the gas lines on this appliance will damage the valve and affect its operation. When installing this appliance, all pipe

and ﬁ ttings must be free from all internal loose dirt.

GAS PRESSURE REGULATOR

A convertible pressure regulator is provided with each griddle. It should be connected to the inlet pipe at the rear of the unit. The gas supply is then connected to it. The supply pressure to the regulator is not to exceed 1/2 psig. This unit is shipped for use with propane

gas with 10" water column manifold pressure.

MANUAL SHUT OFF VALVE

A manual shut off valve should be installed upstream from the manifold and within six feet of the griddle.

CHECKING FOR GAS LEAKS

Check entire piping system for leaks. Soap and water solution or other material acceptable for the purpose, shall be used in locating gas leakage.

CAUTION

Matches, candle ﬂ ame or other sources of ignition shall not be used for locating gas leaks.

LIGHTING INSTRUCTIONS

When the griddle is ﬁ rst lit, it will smoke until the preservative oils and impurities are burned off. The griddles are equipped with standing pilots and should

be lit immediately after the gas is turned on.

MANUAL VALVE AND THROTTLING CONTROL MODELS

1. Turn off the main valve to the unit and wait 5 minutes to clear gas.

2. Turn off all knobs and pilot valves.

3. Turn on main valve to unit and light all pilots.

4. Turn burner knobs to desired position.

5. To turn burners off, turn knobs to off.

CONNECTING GAS SUPPLY LINE

The gas inlet of the griddle is sealed at the factory to prevent entry of dirt. Do not remove this seal until the

actual connection is made to the gas supply line.

NATURAL GAS - CONVERSION

This griddle is equipped with ﬁ xed oriﬁ ce hoods and is shipped from the factory for use with propane gas. To convert to natural gas install the oriﬁ ce hoods located

behind the front panel as follows:

1. Remove the front panel by removing the screws located on the front and bottom.

2. Remove the burner mounting screws in the center of the combustion chamber access covers.

3. Slide the burners back off the oriﬁ ce hoods.

4. Remove the propane gas oriﬁ ce hoods and install the natural oriﬁ ce hoods.

5. Slide the burners back over the oriﬁ ce hoods and reinstall the burner mounting screws.

6. Reinstall the front panel.

7. Set the pressure regulator to 5" (12.7cm) or 4" (10.2cm) water column by removing the slotted or hex cap from the center of the regulator. Invert the plug and reinstall. The letters "NAT" will now be visible on the plug. Reinstall the cap. An 1/8" pipe plug is located on the manifold for attaching a pressure gauge.

SNAP ACTION THERMOSTAT AND CHROME SURFACE MODELS

1. Turn off the main valve to the unit and wait 5 minutes to clear gas.

2. Turn off power switch and turn thermostats to lowest setting.

3. Turn on the main valve.

4. Depress and hold safety pilot reset button. Light pilot. Hold reset button for 60 seconds or until pilot stays lit. Repeat for all pilots.

5. Turn on power switch and set thermostats to desired position.

6. To turn burners off, turn off power switch.

PILOT FLAME ADJUSTMENT

The griddles are equipped with standing pilots and should be lit immediately after the gas is turned on.

MANUAL VALVE AND THROTTLING CONTROL MODELS

Adjust the ﬂ ame as low as possible while still providing immediate burner ignition when the control knob is turned to high.

SNAP ACTION THERMOSTAT AND CHROME SURFACE MODELS

Adjust the pilot so approximately 3/8" of the thermocouple tip is surrounded by the pilot

ﬂ ame.

BURNER AIR SHUTTER ADJUSTMENT

The burner air shutter has a locking screw on the bottom side of the venturi. Loosen this screw to make any adjustment and tighten the screw to lock the air shutter in place after adjustment is complete. Any adjustment must be made when the burner is at full input before the control temperature setting has been satisﬁ ed.

1. Turn the control knob to the highest position and observe the burner ﬂ ame.

2. Slowly decrease the air shutter opening until the ﬂ ame is a soft blue with yellow tips, then increase the opening until the yellow tips disappear and the ﬂ ame is a hard blue.

3. Do not open the shutter to a point where the ﬂ ame is unstable or lifting from the burner surface. The ﬂ ame must be steady and even across the entire

burner.

BYPASS ADJUSTMENT ON THROTTLING CONTROL MODELS ONLY

Throttling control models have a minimum ﬂ ame setting that provides a steady uniform ﬂ ame across the burner when the control heat setting has been satisﬁ ed.

1. Set the control at the maximum setting and wait for the burner ﬂ ame to throttle back.

2. Turn the dial to the 200 degree setting. A small steady ﬂ ame should be visible on all the burner ports. This ﬂ ame should be approximately 1/8" high.

3. An adjustment screw is located either on the front or side of the control housing.

4. Turn clockwise to decrease the ﬂ ame height; turn counterclockwise to increase the ﬂ ame.

ELECTRICAL CONNECTION FOR SNAP ACTION AND CHROME SURFACE MODELS ONLY

Snap action and chrome surface griddles are equipped with a three-prong grounding plug. The unit is designed for use on a 120 volt 15 amp 50/60 cycle AC single-phase circuit only. For protection against electrical shock, the unit must be plugged directly into a properly grounded three-prong receptacle. Do not

cut or remove the grounding prong from this plug.

CAUTION

Do not connect to any other type of current or serious damage will occur.

OPERATING INSTRUCTIONS

SEASONING THE GRIDDLE HEATING SURFACE (NON-CHROME SURFACES)

Clean the griddle surface thoroughly. After the griddle has been thoroughly cleaned, it should be seasoned to prevent food from sticking. Before using and after each thorough scouring, season the griddle heating surface in the following manner:

1. Turn the temperature control dial to 350°F (174.0°C).

2. Using a clean cloth, not a spatula, spread a thin ﬁ lm of cooking oil or shortening over the griddle cooking surface. This ﬁ lm should remain on the hot griddle surface 1/2 hour.

3. Remove excess shortening and wipe clean.

4. Apply another ﬁ lm of cooking oil over the hot cooking area for another 1/2 hour, and again remove excess shortening and wipe clean. The

griddle surface should now be ready for use.

Even with careful seasoning food may, to some extent, stick to the griddle cooking surface until griddle plate is "broken in."

COOKING

Set the dial knob to the setting desired. After a 30 minute (minimum) preheating period, the griddle will automatically maintain the selected temperature.

GRIDDLE CARE (NON-CHROME SURFACES)

It takes very little time and effort to keep the griddle attractive and performing at top efﬁ ciency. If grease is permitted to accumulate, it will form a gummy cake and then carbonize into a hard substance which is extremely difﬁ cult to remove. To prevent this condition, the following suggestions for cleanliness should be followed:

1. After each use, scrape the griddle with a scraper or ﬂ exible spatula to remove excess grease and food. A waste drawer is provided for the scrapings. If there is an accumulation of burned-on grease and food, the griddle should be thoroughly scoured and reseasoned. Use pumice or griddle stone while the griddle is warm. Do not use steel wool because of the danger of steel slivers getting into the food.

2. Use a clean cloth and good non-abrasive cleaner to clean the stainless steel body of the griddle. Wipe the control panel front with a soft cloth.

3. At least once a day, remove the waste drawer and wash in the same way as an ordinary cooking utensil. The drawer is removed by pulling forward

and out.

GRIDDLE CARE (CHROME SURFACES)

(Chrome surface griddles are marked with "CHS" at the end of the model number designation on the nameplate.) It takes very little time and effort to keep this Industrial Chrome griddle surface sparkling clean and performing at top efﬁ ciency. DO NOT allow grease to accumulate as it will carbonize and become difﬁ cult to remove. To prevent this condition, the following cleaning suggestions should be followed:

1. Remove excess oil and food regularly with a 4" (100mm) wide razor sharp type scraper and wipe surface with a damp cloth if desired.

2. Following the scraping, for end of the day cleaning, a damp cloth and a non-silicated, non-abrasive, non-chlorinated cleaner such as Bon-Ami may be used to wipe surface clean, followed by wiping with clean wet cloth.

3. Follow steps 2 and 3 from Griddle Care (NonChrome Surfaces).

CAUTION

1. Never use pumice, griddle stones, or abrasives

on the surface.

2. Never strike the griddle surface with a sharp instrument or spatula edge.

3. Never use steel wool.

4. Never use commercial liquid grill cleaner on the griddle surface.

5. Abusing the surface voids the warranty.

WASTE DRAWER

A waste drawer is located at the front and can be removed from the front for cleaning by pulling drawer forward. This drawer should be checked and emptied

when necessary or at least once per day.

CAUTION

EXERCISE EXTREME CARE IN HANDLING THE WASTE DRAWER CONTAINING HOT GREASE.

OVERNIGHT SHUTDOWN

MANUAL VALVE AND THROTTLING CONTROL MODELS

Turn knobs to the off position to turn burners off.

SNAP ACTION AND CHROME SURFACE MODELS

Turn knobs to the lowest setting and turn power switch off.

CHROME GRIDDLE SURFACE LIMITED WARRANTY EXCLUSIONS

Your chrome griddle has been designed to give you many years of cooking reliability and requires minimum maintenance to keep the chrome surface in its original condition. All chrome griddle surfaces are warranted for a period of 5 years against manufacturing defects to the original owner from the date of installation. This limited warranty is void if it is determined by Star Manufacturing International Incorporated or one of its authorized representatives that the chrome surface has been misused or abused or subjected to the following situations:

1. Improperly installed.

2. By-pass adjustments not set properly on gas units allowing the appliance to overheat and discolor the chrome surface. (See by-pass adjustment section.)

3. The misuse of any instrument or tool which scratches or makes indentations in the surface which could cause the surface to peel, ﬂ ake, or chip off.

4. The use of any chemical or abrasive cleaning solution, griddle brick, stone, screen or other cleaning products which could damage and affect the performance of the chome surface.

5. The neglect of daily routine maintenance to the chrome surface.

Visit our Website at:

This unit has been tested for proper operation before leaving our plant to insure delivery of your unit in perfect condition. However, there are instances in which the unit may be damaged in transit. In the event you discover any type of damage to your product upon receipt, you must immediately contact the transportation company who delivered the item to you and initiate your claim with same. If this procedure is not followed, it may affect the warranty status of the unit.

All workmanship and material in Star products have a one (1) year limited warranty on parts & labor in the United States and Canada. Such warranty is limited to the original purchaser only and shall be effective from the date the equipment is placed in service. Star's obligation under this warranty is limited to the repair of defects without charge, by the factory authorized service agency or one of its sub-agencies. Models that are considered portable (see below) should be taken to the closest Star service agency, transportation prepaid.

www.star-mfg.com Email: service@star-mfg.com

THOROUGHLY INSPECT YOUR UNIT ON ARRIVAL

LIMITED EQUIPMENT WARRANTY

> Star will not assume any responsibility for loss of revenue.

> On all shipments outside the United States and Canada, see International Warranty.

* The warranty period for the JetStar six (6) ounce & Super JetStar eight (8) ounce series popcorn machines is two (2) years.

* The warranty period for the Chrome-Max Griddles is five (5) years on the griddle surface. See detailed warranty provided with unit.

* The warranty period for Teflon/Dura-Tec coatings is one year under normal use and reasonable care. This warranty does not apply if damage occurs to

Teflon/Dura-Tec coatings from improper cleaning, maintenance, use of metallic utensils, or abrasive cleaners. This warranty does not apply to the “non-stick” properties of such materials.

> This warranty does not apply to "Special Products" but to regular catalog items only. Star's warranty on "Special Products" is six (6) months on parts

and ninety (90) days on labor.

> This warranty does not apply to any item that is disassembled or tampered with for any purpose other than repair by a Star Authorized Service Center or

the Service Center's sub-agency.

> This warranty does not apply if damage occurs from improper installation, misuse, wrong voltage, wrong gas or operated contrary to the Installation and

Operating instructions.

> This warranty is not valid on Conveyor Ovens unless a "start-up/check-out" has been performed by a Factory Authorized Technician.

PARTS WARRANTY

Parts that are sold to repair out of warranty equipment are warranted for ninety (90) days. The part only is warranted. Labor to replace the part is chargeable to the customer.

SERVICES NOT COVERED BY WARRANTY

1. Travel time and mileage rendered beyond the 50 mile radius limit

2. Mileage and travel time on portable equipment (see below)

3. Labor to replace such items that can be replaced easily during a daily cleaning routine, ie; removable kettles on fryers, knobs, grease drawers on griddles, etc.

4. Installation of equipment

5. Damages due to improper installation

6. Damages from abuse or misuse

7. Operated contrary to the Operating and Installation Instructions

8. Cleaning of equipment

9. Seasoning of griddle plates

PORTABLE EQUIPMENT

Star will not honor service bills that include travel time and mileage charges for servicing any products considered "Portable" including items listed below. These products should be taken to the Service Agency for repair:

* The Model 510FD Fryer. * The Model J4R, 4 oz. Popcorn Machine. * The Model 518CMA & 526CMA Cheese Melter. * The Model 12MC & 15MC & 18MCP Hot Food Merchandisers. * The Model 12NCPW & 15NCPW Nacho Chip/Popcorn Warmer. * All Hot Dog Equipment except Roller Grills & Drawer Bun Warmers. * All Nacho Cheese Warmers except Model 11WLA Series Nacho Cheese Warmer. * All Condiment Dispensers except the Model HPDE, & SPDE Series Dispenser. * All Specialty Food Warmers except Model 130R, 11RW Series, and 11WSA Series. * All QCS/RCS Series Toasters except Model QCS3 & RCS3 Series.

The foregoing warranty is in lieu of any and all other warranties expressed or implied and constitutes the entire warranty.

FOR ASSISTANCE

Should you need any assistance regarding the Operation or Maintenance of any Star equipment; write, phone, fax or email our Service Department.

In all correspondence mention the Model number and the Serial number of your unit, and the voltage or type of gas you are using.

10 . Voltage conversions 11 . Gas conversions 12 . Pilot light adjustment 13 . Miscellaneous adjustments 14 . Thermostat calibration and by-pass adjustment 15 . Resetting of circuit breakers or safety controls or reset buttons 16 . Replacement of bulbs 17 . Replacement of fuses 18 . Repair of damage created during transit, delivery, &

installation OR created by acts of God

ALL: * Pop-Up Toasters * Butter Dispensers * Pretzel Merchandisers * Pastry Display Cabinets * Nacho Chip Merchandisers * Accessories of any kind * Sneeze Guards * Pizza Ovens * Heat Lamps * Pumps

Part# 2M-4497-2 05/06 RB

+ 28 hidden pages