Star Manufacturing 824T-LP, 824TS-LP, 824TSCHS-LP, 836M-LP, 836T-LP Operation Manual

Star
Manufacturing
International Inc.

10 Sunnen Drive
St. Louis, MO 63143

Phone: [phone]
Fax: [phone]

2M-Z7924 Rev. A 3/15/2006

Installation

and

Operating

Instructions

ULTRA-MAX GAS GRIDDLE

MODELS

824M-LP 824T-LP 824TS-LP 824TSCHS-LP
836M-LP 836T-LP 836TS-LP 836TSCHS-LP
848M-LP 848T-LP 848TS-LP 848TSCHS-LP
860M-LP 860T-LP 860TS-LP 860TSCHS-LP
872M-LP 872T-LP 872TS-LP 872TSCHS-LP

WARNING: Improper installation,
adjustment, alteration, service or
maintenance can cause property damage,
injury or death. Read the installation,
operating and maintenance instructions
thoroughly before installing or servicing
this equipment.

FOR YOUR SAFETY: Do not store or use
gasoline or other fl ammable vapors or
liquids in the vicinity of this or any other
appliance.

WARNING: This appliance shall be installed
in accordance with current regulations and
used only in well-ventilated space. Refer
to instructions before installing and using
this appliance.

In addition, there should be posted, in a
prominent location, detailed instructions
to be followed in the event the operator
smells gas. Obtain the instructions from
the local gas supplier.

1

SAFETY SYMBOL

Using any part other than genuine Star factory supplied parts relieves the
manufacturer of all liability.

Star reserves the right to change specifi cations and product design without
notice. Such revisions do not entitle the buyer to corresponding changes,
improvements, additions or replacements for previously purchased
equipment.

Due to periodic changes in designs, methods, procedures, policies and
regulations, the specifi cations contained in this sheet are subject to change
without notice. While Star Manufacturing exercises good faith efforts to provide
information that is accurate, we are not responsible for errors or omissions
in information provided or conclusions reached as a result of using the
specifi cations. By using the information provided, the user assumes all risks in
connection with such use.

These symbols are intended to alert the user to the presence of
important operating and maintenance instructions in the manual
accompanying the appliance.

RETAIN THIS MANUAL FOR FUTURE REFERENCE

NOTICE

MAINTENANCE AND REPAIRS

Contact your local authorized service agent for service or required maintenance. Please record the model
number, serial number, voltage and purchase date in the area below and have it ready when you call to

ensure a faster service.

Model No.

Serial No.

Voltage

Purchase Date

Authorized Service Agent

Reference the listing provided with the unit

or

for an updated listing go to:

Website: www.star-mfg.com
E-mail [e-mail]
Telephone: [phone] Local [phone]

The Star Service Help Desk

Business 8:00 am to 4:30 p.m. Central Standard Time
Hours:

Telephone: [phone] Local [phone]

Fax: [phone] Local [phone]

E-mail [e-mail]

[e-mail]
[e-mail]

Website: www.star-mfg.com

Mailing Address: Star Manufacturing International Inc.

10 Sunnen Drive
St. Louis, MO 63143
U.S.A

2

2

SPECIFICATIONS

824M-LP

Type: Manual Valve

2 Controls, 60,000 BTUH, 573 sq. in. (3697 sq. cm) Grid Area
Approximate Weight: Installed - 214 Lb s (97.0 kg), shipping - 244 Lbs (110.6 kg)
Dimensions: 24" - Width, 32 3/8" - Depth, 18" - Height
(61 cm - Width, 82.2 cm - Depth, 45.7 cm - Height)

836M-LP

Type: Manual Valve

3 Controls, 90,000 BTUH, 860 sq. in. (5545 sq. cm) Grid Area
Approximate Weight: Installed - 321 Lbs (145.4 kg), shipping - 366 Lbs (165.8 kg)
Dimensions: 36" - Width, 32 3/8" - Depth, 18" - Height
(91.4 cm - Width, 82.2 cm - Depth, 45.7 cm - Height)

848M-LP

Type: Manual Valve

4 Controls, 120,000 BTUH, 1146 sq. in. (7394 sq. cm) Grid Area
Approximate Weight: Installed - 428 Lbs (193.9 kg), shipping - 488 Lbs (221.1 kg)
Dimensions: 48" - Width, 32 3/8" - Depth, 18" - Height
(122 cm - Width, 82.2 cm - Depth, 45.7 cm - Height)

860M-LP

Type: Manual Valve

5 Controls, 150,000 BTUH, 1433 sq. in. (9242 sq. cm) Grid Area
Approximate Weight: Installed - 535 Lbs (242.4 kg), shipping - 610 Lbs (276.4 kg)
Dimensions: 60" - Width, 32 3/8" - Depth, 18" - Height
(152.4 cm - Width, 82.2 cm - Depth, 45.7 cm - Height)

872M-LP

Type: Manual Valve

6 Controls, 180,000 BTUH, 1719 sq. in. (11091 sq. cm) Grid Area
Approximate Weight: Installed - 642 Lbs (290.9 kg), shipping - 732 Lbs (331.7 kg)
Dimensions: 72" - Width, 32 3/8" - Depth, 18" - Height
(182.9 cm - Width, 82.2 cm - Depth, 45.7 cm - Height)

824T-LP

Type: Throttling Control

2 Controls, 60,000 BTUH, 573 sq. in. (3697 sq. cm) Grid Area
Approximate Weight: Installed - 220 Lb s (99.7 kg), shipping - 246 Lbs (111.5 kg)
Dimensions: 24" - Width, 32 3/8" - Depth, 18" - Height
(61 cm - Width, 82.2 cm - Depth, 45.7 cm - Height)

836T-LP

Type: Throttling Control

3 Controls, 90,000 BTUH, 860 sq. in. (5545 sq. cm) Grid Area
Approximate Weight: Installed - 330 Lbs (149.5 kg), shipping - 369 Lbs (167.2 kg)
Dimensions: 36" - Width, 32 3/8" - Depth, 18" - Height
(91.4 cm - Width, 82.2 cm - Depth, 45.7 cm - Height)

848T-LP

Type: Throttling Control

4 Controls, 120,000 BTUH, 1146 sq. in. (7394 sq. cm) Grid Area
Approximate Weight: Installed - 440 Lbs (199.4 kg), shipping - 492 Lbs (222.9 kg)
Dimensions: 48" - Width, 32 3/8" - Depth, 18" - Height
(122 cm - Width, 82.2 cm - Depth, 45.7 cm - Height)

3

860T-LP

Type: Throttling Control

5 Controls, 150,000 BTUH, 1433 sq. in. (9242 sq. cm) Grid Area
Approximate Weight: Installed - 550 Lbs (249.2 kg), shipping - 615 Lbs (278.7 kg)
Dimensions: 60" - Width, 32 3/8" - Depth, 18" - Height

(152.4 cm - Width, 82.2 cm - Depth, 45.7 cm - Height)

872T-LP

Type: Throttling Control

6 Controls, 180,000 BTUH, 1719 sq. in. (11091 sq. cm) Grid Area
Approximate Weight: Installed - 660 Lbs (299.0 kg), shipping - 738 Lbs (334.4 kg)
Dimensions: 72" - Width, 32 3/8" - Depth, 18" - Height

(182.9 cm - Width, 82.2 cm - Depth, 45.7 cm - Height)

824TS-LP

Type: Snap Action Control With Safety Pilot

2 Controls, 60,000 BTUH, 573 sq. in. (3697 sq. cm) Grid Area
Approximate Weight: Installed - 222 Lb s (100.6 kg), shipping - 250 Lbs (113.3 kg)
Dimensions: 24" - Width, 32 3/8" - Depth, 18" - Height
(61 cm - Width, 82.2 cm - Depth, 45.7 cm - Height)

836TS-LP

Type: Snap Action Control With Safety Pilot

3 Controls, 90,000 BTUH, 860 sq. in. (5545 sq. cm) Grid Area
Approximate Weight: Installed - 333 Lbs (150.9 kg), shipping - 375 Lbs (169.9 kg)
Dimensions: 36" - Width, 32 3/8" - Depth, 18" - Height
(91.4 cm - Width, 82.2 cm - Depth, 45.7 cm - Height)

848TS-LP

Type:Snap Action Control With Safety Pilot

4 Controls, 120,000 BTUH, 1146 sq. in. (7394 sq. cm) Grid Area
Approximate Weight: Installed - 444 Lbs (201.2 kg), shipping - 500 Lbs (226.6 kg)
Dimensions: 48" - Width, 32 3/8" - Depth, 18" - Height
(122 cm - Width, 82.2 cm - Depth, 45.7 cm - Height)

860TS-LP

Type: Snap Action Control With Safety Pilot

5 Controls, 150,000 BTUH, 1433 sq. in. (9242 sq. cm) Grid Area
Approximate Weight: Installed - 555 Lbs (251.5 kg), shipping - 625 Lbs (283.2 kg)
Dimensions: 60" - Width, 32 3/8" - Depth, 18" - Height
(152.4 cm - Width, 82.2 cm - Depth, 45.7 cm - Height)

872TS-LP

Type: Snap Action Control With Safety Pilot

6 Controls, 180,000 BTUH, 1719 sq. in. (11091 sq. cm) Grid Area
Approximate Weight: Installed - 666 Lbs (301.8 kg), shipping - 750 Lbs (339.8 kg)
Dimensions: 72" - Width, 32 3/8" - Depth, 18" - Height

(182.9 cm - Width, 82.2 cm - Depth, 45.7 cm - Height)

824TSCHS-LP

Type: Snap Action With Safety Pilot and Chrome Plate
2 Controls, 60,000 BTUH, 573 sq. in. (3697 sq. cm) Grid Area
Approximate Weight: Installed - 222 Lb s (100.6 kg), shipping - 250 Lbs (113.3 kg)
Dimensions: 24" - Width, 32 3/8" - Depth, 18" - Height
(61 cm - Width, 82.2 cm - Depth, 45.7 cm - Height)

4

836TSCHS-LP

Type: Snap Action Control With Safety Pilot and Chrome Plate

3 Controls, 90,000 BTUH, 860 sq. in. (5545 sq. cm) Grid Area
Approximate Weight: Installed - 333 Lbs (150.9 kg), shipping - 375 Lbs (169.9 kg)
Dimensions: 36" - Width, 32 3/8" - Depth, 18" - Height
(91.4 cm - Width, 82.2 cm - Depth, 45.7 cm - Height)

848TSCHS-LP

Type: Snap Action Control With Safety Pilot and Chrome Plate

4 Controls, 120,000 BTUH, 1146 sq. in. (7394 sq. cm) Grid Area
Approximate Weight: Installed - 444 Lbs (201.2 kg), shipping - 500 Lbs (226.6 kg)
Dimensions: 48" - Width, 32 3/8" - Depth, 18" - Height

(122 cm - Width, 82.2 cm - Depth, 45.7 cm - Height)

860TSCHS-LP

Type: Snap Action Control With Safety Pilot and Chrome Plate

5 Controls, 150,000 BTUH, 1433 sq. in. (9242 sq. cm) Grid Area
Approximate Weight: Installed - 555 Lbs (251.5 kg), shipping - 625 Lbs (283.2 kg)
Dimensions: 60" - Width, 32 3/8" - Depth, 18" - Height

(152.4 cm - Width, 82.2 cm - Depth, 45.7 cm - Height)

872TSCHS-LP

Type: Snap Action Control With Safety Pilot and Chrome Plate

6 Controls, 180,000 BTUH, 1719 sq. in. (11091 sq. cm) Grid Area
Approximate Weight: Installed - 666 Lbs (301.8 kg), shipping - 750 Lbs (339.8 kg)
Dimensions: 72" - Width, 32 3/8" - Depth, 18" - Height
(182.9 cm - Width, 82.2 cm - Depth, 45.7 cm - Height)

5

GENERAL INSTALLATION DATA

NOTICE

CAUTION

This equipment is designed and sold for commercial
use only by personnel trained and experienced in its
operation and is not sold for consumer use in and
around the home nor for use directly by the general
public in food service locations.

Ultra-Max series griddles are equipped for use on
either natural or propane gas. This unit is shipped for
propane gas and can easily be converted to natural.

See Natural Gas - Conversion.

-IMPORTANT-

Be sure to remove all paper protection and packing
material from unit prior to lighting. Remove the
protective plastic from the griddle plate and thoroughly
clean the unit's exterior surfaces.

KEEP THE APPLIANCE AREA FREE AND
CLEAR FROM COMBUSTIBLES! For use on

non-combustible countertops only. Combustible and
non-combustible material must be at least 48" (120cm)
from the top of the appliance and at least 6" (16cm)
from the sides and back. Adequate clearance should
also be provided for proper operation and servicing.

The installation of the Appliance must
conform to the NATIONAL FUEL GAS CODE
"ANSI Z223.1 - LATEST EDITION" AND
ALL LOCAL GAS COMPANY RULES AND
REGULATIONS.

IN CANADA INSTALLATION SHALL BE IN
ACCORDANCE WITH THE CURRENT CAN/
CGA-B149.1 NATURAL GAS INSTALLATION
CODE OR CAN/CGA-B149.2 PROPANE
INSTALLATION CODE AND LOCAL CODES
WHERE APPLICABLE.

When this appliance is installed with casters, it must
be installed with the casters supplied, a connector
complying with either ANSI Z21.69 or CAN/CGA-6.16
and a quick-disconnect device complying with either
ANSI Z21.41 or CAN1-6.9. It must also be installed
with restraining means to guard against transmission
of strain to the connector.

For your protection, we recommend a qualifi ed
installing agency install this appliance. They
should be familiar with gas installations and your
local gas requirements. In any case, your gas
company should be called to approve the fi nal

installation.

This appliance, its pressure regulator and its individual
shutoff valve must be disconnected from the gas
supply piping system during any pressure testing of
that system at test pressures in excess of 1/2 PSIG.
This appliance and its pressure regulator must be
isolated from the gas supply piping system by closing
its individual manual shutoff valve during any pressure
testing of the gas supply piping system at test pressures

equal to or less than 1/2 PSIG.

EXHAUST CANOPY

Griddles inherently create a good deal of heat and
smoke and should be installed under an effi cient
exhaust hood with fl ame proof fi lters. A vertical distance
of not less than 48" shall be provided between the top
of the appliance and fi lters or any other combustible
material. Exhaust installation must conform to local
codes.

AIR SUPPLY

Provisions for adequate air supply must be
provided.

CAUTION

AIR INTAKES IN BOTTOM

Air for combustion enters from the bottom of the unit.

Do not obstruct this area.

6

LEVELING UNIT

This griddle is supplied with 4 feet or fl oor stand
legs which must be screwed into the body. Unit
must be level. Level unit by adjusting the (4) feet
which have an adjustment of 1-3/4" for accurate
and perfect line-up with other units.

CAUTION

DO NOT INSTALL WITHOUT ATTACHING FEET
OR SUPPLIED STAND LEGS AND SHELF - DO
NOT REMOVE FEET.

Caster Kits: Casters can be used with fl oor stand
models or optional equipment stand. For installation,
carefully mark and cut off from the bottom of each leg
using a straight cutting saw and de-burr the inside
tube wall prior to installing the caster. Cut leg should
measure 19" tube length, not overall length. Casters
add about 6-1/4" of height to the unit. Be sure to use
approved strain relief means for protecting gas line
connection. If an appliance is equipped with casters
and is gas connected with a quick connect coupling,
all personnel must be aware that there is a restraint
on the appliance and if disconnected for service or
cleaning it must be reconnected as originally installed
prior to use.

7

GAS PIPING

Gas piping shall be of such size and so installed as
to provide a supply of gas suffi cient to meet the full
gas input of the appliance. If the appliance is to be
connected to existing piping, it shall be checked to
determine if it has adequate capacity. Joint compound
shall be used sparingly and only on the male threads
of the pipe joints. Such compounds shall be resistant
to the action of L.P. gases. WARNING: Any loose dirt
or metal particles which are allowed to enter the gas
lines on this appliance will damage the valve and affect
its operation. When installing this appliance, all pipe

and fi ttings must be free from all internal loose dirt.

GAS PRESSURE REGULATOR

A convertible pressure regulator is provided with each
griddle. It should be connected to the inlet pipe at the
rear of the unit. The gas supply is then connected to it.
The supply pressure to the regulator is not to exceed
1/2 psig. This unit is shipped for use with propane

gas with 10" water column manifold pressure.

MANUAL SHUT OFF VALVE

A manual shut off valve should be installed upstream
from the manifold and within six feet of the griddle.

CHECKING FOR GAS LEAKS

Check entire piping system for leaks. Soap and
water solution or other material acceptable for the
purpose, shall be used in locating gas leakage.

CAUTION

Matches, candle fl ame or other sources of
ignition shall not be used for locating gas
leaks.

LIGHTING INSTRUCTIONS

When the griddle is fi rst lit, it will smoke until the
preservative oils and impurities are burned off. The
griddles are equipped with standing pilots and should

be lit immediately after the gas is turned on.

MANUAL VALVE AND THROTTLING CONTROL
MODELS

1. Turn off the main valve to the unit and wait 5
minutes to clear gas.

2. Turn off all knobs and pilot valves.

3. Turn on main valve to unit and light all pilots.

4. Turn burner knobs to desired position.

5. To turn burners off, turn knobs to off.

CONNECTING GAS SUPPLY LINE

The gas inlet of the griddle is sealed at the factory to
prevent entry of dirt. Do not remove this seal until the

actual connection is made to the gas supply line.

NATURAL GAS - CONVERSION

This griddle is equipped with fi xed orifi ce hoods and is
shipped from the factory for use with propane gas. To
convert to natural gas install the orifi ce hoods located

behind the front panel as follows:

1. Remove the front panel by removing the screws
located on the front and bottom.

2. Remove the burner mounting screws in the center
of the combustion chamber access covers.

3. Slide the burners back off the orifi ce hoods.

4. Remove the propane gas orifi ce hoods and install
the natural orifi ce hoods.

5. Slide the burners back over the orifi ce hoods and
reinstall the burner mounting screws.

6. Reinstall the front panel.

7. Set the pressure regulator to 5" (12.7cm) or 4"
(10.2cm) water column by removing the slotted
or hex cap from the center of the regulator. Invert
the plug and reinstall. The letters "NAT" will now
be visible on the plug. Reinstall the cap. An 1/8"
pipe plug is located on the manifold for attaching
a pressure gauge.

SNAP ACTION THERMOSTAT AND CHROME
SURFACE MODELS

1. Turn off the main valve to the unit and wait 5
minutes to clear gas.

2. Turn off power switch and turn thermostats to
lowest setting.

3. Turn on the main valve.

4. Depress and hold safety pilot reset button.
Light pilot. Hold reset button for 60 seconds
or until pilot stays lit. Repeat for all pilots.

5. Turn on power switch and set thermostats to
desired position.

6. To turn burners off, turn off power switch.

8

PILOT FLAME ADJUSTMENT

The griddles are equipped with standing pilots and
should be lit immediately after the gas is turned on.

MANUAL VALVE AND THROTTLING
CONTROL MODELS

Adjust the fl ame as low as possible while still
providing immediate burner ignition when the
control knob is turned to high.

SNAP ACTION THERMOSTAT AND
CHROME SURFACE MODELS

Adjust the pilot so approximately 3/8" of the
thermocouple tip is surrounded by the pilot

fl ame.

BURNER AIR SHUTTER ADJUSTMENT

The burner air shutter has a locking screw on the
bottom side of the venturi. Loosen this screw to
make any adjustment and tighten the screw to lock
the air shutter in place after adjustment is complete.
Any adjustment must be made when the burner is at
full input before the control temperature setting has
been satisfi ed.

1. Turn the control knob to the highest position and
observe the burner fl ame.

2. Slowly decrease the air shutter opening until the
fl ame is a soft blue with yellow tips, then increase
the opening until the yellow tips disappear and the
fl ame is a hard blue.

3. Do not open the shutter to a point where the fl ame
is unstable or lifting from the burner surface. The
fl ame must be steady and even across the entire

burner.

BYPASS ADJUSTMENT ON THROTTLING
CONTROL MODELS ONLY

Throttling control models have a minimum fl ame setting
that provides a steady uniform fl ame across the burner
when the control heat setting has been satisfi ed.

1. Set the control at the maximum setting and wait
for the burner fl ame to throttle back.

2. Turn the dial to the 200 degree setting. A small
steady fl ame should be visible on all the burner
ports. This fl ame should be approximately 1/8"
high.

3. An adjustment screw is located either on the front
or side of the control housing.

4. Turn clockwise to decrease the fl ame height; turn
counterclockwise to increase the fl ame.

ELECTRICAL CONNECTION FOR SNAP
ACTION AND CHROME SURFACE MODELS
ONLY

Snap action and chrome surface griddles are equipped
with a three-prong grounding plug. The unit is
designed for use on a 120 volt 15 amp 50/60 cycle
AC single-phase circuit only. For protection against
electrical shock, the unit must be plugged directly into
a properly grounded three-prong receptacle. Do not

cut or remove the grounding prong from this plug.

CAUTION

Do not connect to any other type of current
or serious damage will occur.

OPERATING INSTRUCTIONS

SEASONING THE GRIDDLE HEATING
SURFACE (NON-CHROME SURFACES)

Clean the griddle surface thoroughly. After the griddle
has been thoroughly cleaned, it should be seasoned
to prevent food from sticking. Before using and after
each thorough scouring, season the griddle heating
surface in the following manner:

1. Turn the temperature control dial to 350°F
(174.0°C).

2. Using a clean cloth, not a spatula, spread a thin
fi lm of cooking oil or shortening over the griddle
cooking surface. This fi lm should remain on the
hot griddle surface 1/2 hour.

3. Remove excess shortening and wipe clean.

4. Apply another fi lm of cooking oil over the hot
cooking area for another 1/2 hour, and again
remove excess shortening and wipe clean. The

griddle surface should now be ready for use.

Even with careful seasoning food may, to some
extent, stick to the griddle cooking surface
until griddle plate is "broken in."

COOKING

Set the dial knob to the setting desired. After a 30
minute (minimum) preheating period, the griddle will
automatically maintain the selected temperature.

9

GRIDDLE CARE (NON-CHROME
SURFACES)

It takes very little time and effort to keep the griddle
attractive and performing at top effi ciency. If grease
is permitted to accumulate, it will form a gummy cake
and then carbonize into a hard substance which is
extremely diffi cult to remove. To prevent this condition,
the following suggestions for cleanliness should be
followed:

1. After each use, scrape the griddle with a scraper
or fl exible spatula to remove excess grease and
food. A waste drawer is provided for the scrapings.
If there is an accumulation of burned-on grease
and food, the griddle should be thoroughly scoured
and reseasoned. Use pumice or griddle stone
while the griddle is warm. Do not use steel wool
because of the danger of steel slivers getting into
the food.

2. Use a clean cloth and good non-abrasive cleaner
to clean the stainless steel body of the griddle.
Wipe the control panel front with a soft cloth.

3. At least once a day, remove the waste drawer
and wash in the same way as an ordinary cooking
utensil. The drawer is removed by pulling forward

and out.

GRIDDLE CARE (CHROME SURFACES)

(Chrome surface griddles are marked with "CHS"
at the end of the model number designation on the
nameplate.) It takes very little time and effort to keep
this Industrial Chrome griddle surface sparkling clean
and performing at top effi ciency. DO NOT allow grease
to accumulate as it will carbonize and become diffi cult
to remove. To prevent this condition, the following
cleaning suggestions should be followed:

1. Remove excess oil and food regularly with a 4"
(100mm) wide razor sharp type scraper and wipe
surface with a damp cloth if desired.

2. Following the scraping, for end of the day cleaning,
a damp cloth and a non-silicated, non-abrasive,
non-chlorinated cleaner such as Bon-Ami may be
used to wipe surface clean, followed by wiping
with clean wet cloth.

3. Follow steps 2 and 3 from Griddle Care (Non­Chrome Surfaces).

CAUTION

1. Never use pumice, griddle stones, or abrasives

on the surface.

2. Never strike the griddle surface with a sharp
instrument or spatula edge.

3. Never use steel wool.

4. Never use commercial liquid grill cleaner on the
griddle surface.

5. Abusing the surface voids the warranty.

WASTE DRAWER

A waste drawer is located at the front and can be
removed from the front for cleaning by pulling drawer
forward. This drawer should be checked and emptied

when necessary or at least once per day.

CAUTION

EXERCISE EXTREME CARE IN HANDLING
THE WASTE DRAWER CONTAINING HOT
GREASE.

OVERNIGHT SHUTDOWN

MANUAL VALVE AND THROTTLING CONTROL
MODELS

Turn knobs to the off position to turn burners off.

SNAP ACTION AND CHROME SURFACE
MODELS

Turn knobs to the lowest setting and turn power
switch off.

10

CHROME GRIDDLE SURFACE LIMITED
WARRANTY EXCLUSIONS

Your chrome griddle has been designed to give you
many years of cooking reliability and requires minimum
maintenance to keep the chrome surface in its original
condition. All chrome griddle surfaces are warranted
for a period of 5 years against manufacturing defects
to the original owner from the date of installation.
This limited warranty is void if it is determined by Star
Manufacturing International Incorporated or one of its
authorized representatives that the chrome surface has
been misused or abused or subjected to the following
situations:

1. Improperly installed.

2. By-pass adjustments not set properly on gas units
allowing the appliance to overheat and discolor
the chrome surface. (See by-pass adjustment
section.)

3. The misuse of any instrument or tool which scratches
or makes indentations in the surface which could
cause the surface to peel, fl ake, or chip off.

4. The use of any chemical or abrasive cleaning
solution, griddle brick, stone, screen or other
cleaning products which could damage and affect
the performance of the chome surface.

5. The neglect of daily routine maintenance to the
chrome surface.

11

Visit our Website at:

This unit has been tested for proper operation before leaving our plant to insure delivery of your unit in perfect condition. However, there are instances in
which the unit may be damaged in transit. In the event you discover any type of damage to your product upon receipt, you must immediately contact the
transportation company who delivered the item to you and initiate your claim with same. If this procedure is not followed, it may affect the warranty
status of the unit.

All workmanship and material in Star products have a one (1) year limited warranty on parts & labor in the United States and Canada. Such warranty is
limited to the original purchaser only and shall be effective from the date the equipment is placed in service. Star's obligation under this warranty is limited
to the repair of defects without charge, by the factory authorized service agency or one of its sub-agencies. Models that are considered portable (see below)
should be taken to the closest Star service agency, transportation prepaid.

www.star-mfg.com Email: [e-mail]

THOROUGHLY INSPECT YOUR UNIT ON ARRIVAL

LIMITED EQUIPMENT WARRANTY

> Star will not assume any responsibility for loss of revenue.

> On all shipments outside the United States and Canada, see International Warranty.

* The warranty period for the JetStar six (6) ounce & Super JetStar eight (8) ounce series popcorn machines is two (2) years.

* The warranty period for the Chrome-Max Griddles is five (5) years on the griddle surface. See detailed warranty provided with unit.

* The warranty period for Teflon/Dura-Tec coatings is one year under normal use and reasonable care. This warranty does not apply if damage occurs to

Teflon/Dura-Tec coatings from improper cleaning, maintenance, use of metallic utensils, or abrasive cleaners. This warranty does not apply to the
“non-stick” properties of such materials.

> This warranty does not apply to "Special Products" but to regular catalog items only. Star's warranty on "Special Products" is six (6) months on parts

and ninety (90) days on labor.

> This warranty does not apply to any item that is disassembled or tampered with for any purpose other than repair by a Star Authorized Service Center or

the Service Center's sub-agency.

> This warranty does not apply if damage occurs from improper installation, misuse, wrong voltage, wrong gas or operated contrary to the Installation and

Operating instructions.

> This warranty is not valid on Conveyor Ovens unless a "start-up/check-out" has been performed by a Factory Authorized Technician.

PARTS WARRANTY

Parts that are sold to repair out of warranty equipment are warranted for ninety (90) days. The part only is warranted. Labor to replace the part is
chargeable to the customer.

SERVICES NOT COVERED BY WARRANTY

1. Travel time and mileage rendered beyond the 50 mile radius limit

2. Mileage and travel time on portable equipment (see below)

3. Labor to replace such items that can be replaced easily during a daily cleaning
routine, ie; removable kettles on fryers, knobs, grease drawers on griddles, etc.

4. Installation of equipment

5. Damages due to improper installation

6. Damages from abuse or misuse

7. Operated contrary to the Operating and Installation Instructions

8. Cleaning of equipment

9. Seasoning of griddle plates

PORTABLE EQUIPMENT

Star will not honor service bills that include travel time and mileage charges for servicing any products considered "Portable" including items listed below.
These products should be taken to the Service Agency for repair:

* The Model 510FD Fryer.
* The Model J4R, 4 oz. Popcorn Machine.
* The Model 518CMA & 526CMA Cheese Melter.
* The Model 12MC & 15MC & 18MCP Hot Food Merchandisers.
* The Model 12NCPW & 15NCPW Nacho Chip/Popcorn Warmer.
* All Hot Dog Equipment except Roller Grills & Drawer Bun Warmers.
* All Nacho Cheese Warmers except Model 11WLA Series Nacho Cheese Warmer.
* All Condiment Dispensers except the Model HPDE, & SPDE Series Dispenser.
* All Specialty Food Warmers except Model 130R, 11RW Series, and 11WSA Series.
* All QCS/RCS Series Toasters except Model QCS3 & RCS3 Series.

The foregoing warranty is in lieu of any and all other warranties expressed or implied and constitutes the entire warranty.

FOR ASSISTANCE

Should you need any assistance regarding the Operation or Maintenance of any Star equipment; write, phone, fax or email our Service Department.

In all correspondence mention the Model number and the Serial number of your unit, and the voltage or type of gas you are using.

10 . Voltage conversions
11 . Gas conversions
12 . Pilot light adjustment
13 . Miscellaneous adjustments
14 . Thermostat calibration and by-pass adjustment
15 . Resetting of circuit breakers or safety controls or reset buttons
16 . Replacement of bulbs
17 . Replacement of fuses
18 . Repair of damage created during transit, delivery, &

installation OR created by acts of God

ALL:
* Pop-Up Toasters
* Butter Dispensers
* Pretzel Merchandisers
* Pastry Display Cabinets
* Nacho Chip Merchandisers
* Accessories of any kind
* Sneeze Guards
* Pizza Ovens
* Heat Lamps
* Pumps

Part# 2M-4497-2 05/06 RB

12

13

PARTS LIST March 15, 2006, Rev. A

824-LP Series Gas Griddles

MODEL

Number

Key

Number

1 G5-Z4812 1 FLUE 824M/T/TS/TSCHS
3 G5-824004 1 GRIDDLE PLATE ASSY COMPLETE 824M
G5-824005 1 GRIDDLE PLATE ASSY COMPLETE 824T/TS
G5-824006 1 GRIDDLE PLATE ASSY COMPLETE 824TSCHS
4 G5-Z4793 2 BULB CLAMP 824T/TS/TSCHS
5 G5-Z4794 2 BULB COVER 824T/TS/TSCHS
6 G5-Z4795 6 BULB SPRING 824T/TS/TSCHS
7 G5-Z4927 2 ORIFICE BRACKET 824M/T/TS/TSCHS
8 2F-Z4613 2 BURNER 824M/T/TS/TSCHS
9 G5-Z4800 1 SIDE BAFFLE RIGHT ALL 824/36/48/60/72
10 2A-Z4614 4 FOOT ALL 824/36/48/60/72
11 G5-824014 1 WASTE DRAWER ASSY ALL 824/836/848
12 G5-Z4897 1 DRAWER GUIDE ALL 824/836/848
13 G5-Z4799 1 PILOT BAFFLE 824TS/TSCHS
14 G5-Z4798 1 BURNER BAFFLE 824M/T
15 G5-Z4900 2 BURNER COVER 824M/T/TS/TSCHS
16 2A-9369 2 ORIFICE FITTING 824M/T/TS/TSCHS
17 2A-Z4930 2 ORIFICE NATURAL 824M/T
2A-Z5542 2 ORIFICE NATURAL 824TS/TSCHS
2A-Z4931 2 ORIFICE PROPANE 824M/T/TS/TSCHS
18 G5-Z4801 1 SIDE BAFFLE LEFT ALL 824/36/48/60/72
19 2M-Z4864 1 CONTROL GRAPHICS PANEL 824TS/TSCHS
20 2R-Z4997 2 KNOB 824M/T
2R-Z8891 2 KNOB 824TS/TSCHS manuf. after 8/05
PS-Z9312 2 KNOB SERVICE KIT 824TS/TSCHS manuf. before 8/05
21 G5-824012 1 CHUTE ASSEMBLY ALL 824/836/848
22 G5-824008 1 FRONT PANEL ASSEMBLY 824M/T
23 G5-824013 1 FRONT PANEL ASSEMBLY 824TS/TSCHS
24 2M-Z4862 1 CONTROL GRAPHICS PANEL 824M
2M-Z4863 1 CONTROL GRAPHICS PANEL 824T
25 G5-824007 1 BODY ASSEMBLY 824M/T/TS/TSCHS
26 VARIOUS 1 NAMEPLATE ALL
N/A 2J-Z4686 1 REGULATOR (5” AND 10”) ALL M/T
N/A 2J-Z5541 1 REGULATOR (4” AND 10”) ALL TS/TSCHS
N/A 2C-Z8547 2 BOLT, KNOB STOP ALL

Part

Number

Per

Unit

Description and Model Designation

1

IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED PAGE

1

INCLUDE MODEL AND SERIAL NUMBER OF

Some items are included for illustrative purposes only and in certain instances may not be available.

Star Manufacturing International, Inc.

14

PARTS LIST Mach 15, 2006, Rev. A

836-LP Series Gas Griddles

MODEL

Number

Key

Number

1 G5-Z4813 1 FLUE 836M/T/TS/TSCHS
2 G5-Z4817 1 FLUE DIVIDER 836M/T/TS/TSCHS
3 G5-836004 1 GRIDDLE PLATE ASSY COMPLETE 836M
3 G5-836005 1 GRIDDLE PLATE ASSY COMPLETE 836T/TS
3 G5-836006 1 GRIDDLE PLATE ASSY COMPLETE 836TSCHS
4 G5-Z4793 3 BULB CLAMP 836T/TS/TSCHS
5 G5-Z4794 3 BULB COVER 836T/TS/TSCHS
6 G5-Z4795 9 BULB SPRING 836T/TS/TSCHS
7 G5-Z4927 3 ORIFICE BRACKET 836M/T/TS/TSCHS
8 2F-Z4613 3 BURNER 836M/T/TS/TSCHS
9 G5-Z4800 1 SIDE BAFFLE RIGHT ALL 824/36/48/60/72
10 2A-Z4614 4 FOOT ALL 824/36/48/60/72
11 G5-824014 1 WASTE DRAWER ASSY ALL 824/836/848
12 G5-Z4897 1 DRAWER GUIDE ALL 824/836/848
13 G5-Z4799 2 PILOT BAFFLE 836TS/TSCHS
14 G5-Z4798 2 BURNER BAFFLE 836M/T
15 G5-Z4900 3 BURNER COVER 836M/T/TS/TSCHS
16 2A-9369 3 ORIFICE FITTING 836M/T/TS/TSCHS
17 2A-Z4930 3 ORIFICE NATURAL 836M/T
17 2A-Z4931 3 ORIFICE PROPANE 836M/T/TS/TSCHS
17 2A-Z5542 3 ORIFICE NATURAL 836TS/TSCHS
18 G5-Z4801 1 SIDE BAFFLE LEFT ALL 824/36/48/60/72
19 2M-Z4867 1 CONTROL GRAPHICS PANEL 836TS/TSCHS
20 2R-Z4997 3 KNOB 836M/T
2R-Z8891 3 KNOB 836TS/TSCHS manuf. after 8/2005
PS-Z9312 3 KNOB SERVICE KIT 836TS/TSCHS manuf. before 8/2005
21 G5-824012 1 CHUTE ASSEMBLY ALL 824/836/848
22 G5-836008 1 FRONT PANEL ASSEMBLY 836M/T
23 G5-836013 1 FRONT PANEL ASSEMBLY 836TS/TSCHS
24 2M-Z4865 1 CONTROL GRAPHICS PANEL 836M
24 2M-Z4866 1 CONTROL GRAPHICS PANEL 836T
25 G5-836007 1 BODY ASSEMBLY 836M/T/TS/TSCHS
26 VARIOUS 1 NAMEPLATE ALL
N/A 2J-Z4686 1 REGULATOR (5” AND 10”) ALL M/T
N/A 2J-Z5541 1 REGULATOR (4” AND 10”) ALL TS/TSCHS

Part

Number

Per

Unit

Description and Model Designation

1

IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED PAGE

1

INCLUDE MODEL AND SERIAL NUMBER OF

Some items are included for illustrative purposes only and in certain instances may not be available.

Star Manufacturing International, Inc.

15

PARTS LIST March 15, 2006, Rev. A

848-LP Series Gas Griddles

MODEL

Number

Key

Number

1 G5-Z4814 1 FLUE 848M/T/TS/TSCHS
2 G5-Z4817 1 FLUE DIVIDER 848M/T/TS/TSCHS
3 G5-848004 1 GRIDDLE PLATE ASSY COMPLETE 848M
3 G5-848005 1 GRIDDLE PLATE ASSY COMPLETE 848T/TS
3 G5-848006 1 GRIDDLE PLATE ASSY COMPLETE 848TSCHS
4 G5-Z4793 4 BULB CLAMP 848T/TS/TSCHS
5 G5-Z4794 4 BULB COVER 848T/TS/TSCHS
6 G5-Z4795 12 BULB SPRING 848T/TS/TSCHS
7 G5-Z4928 4 ORIFICE BRACKET 848M/T/TS/TSCHS
8 2F-Z4613 4 BURNER 848M/T/TS/TSCHS
9 G5-Z4800 1 SIDE BAFFLE RIGHT ALL 824/36/48/60/72
10 2A-Z4614 4 FOOT ALL 824/36/48/60/72
11 G5-824014 1 WASTE DRAWER ASSY ALL 824/836/848
11 G5-824014 2 WASTE DRAWER ASSY ALL 860/872
12 G5-Z4897 1 DRAWER GUIDE ALL 824/836/848
12 G5-Z4897 2 DRAWER GUIDE ALL 860/872
13 G5-Z4799 2 PILOT BAFFLE 848TS/TSCHS
14 G5-Z4798 3 BURNER BAFFLE 848M/T
14 G5-Z4798 1 BURNER BAFFLE 848TS/TSCHS
15 G5-Z4900 4 BURNER COVER 848M/T/TS/TSCHS
16 2A-9369 4 ORIFICE FITTING 848M/T/TS/TSCHS
17 2A-Z4930 4 ORIFICE NATURAL 848M/T
17 2A-Z4931 4 ORIFICE PROPANE 848M/T/TS/TSCHS
17 2A-Z5542 4 ORIFICE NATURAL 848TS/TSCHS
18 G5-Z4801 1 SIDE BAFFLE LEFT ALL 824/36/48/60/72
19 2M-Z4870 1 CONTROL GRAPHICS PANEL 848TS/TSCHS
20 2R-Z4997 4 KNOB 848M/T
2R-Z8891 4 KNOB 848TS/TSCHS manuf. after 8/2005
PS-Z9312 4 KNOB SERVICE KIT 848TS/TSCHS manuf. before 8/2005
21 G5-824012 1 CHUTE ASSEMBLY ALL 824/836/848
22 G5-848008 1 FRONT PANEL ASSEMBLY 848M/T
23 G5-848013 1 FRONT PANEL ASSEMBLY 848TS/TSCHS
24 2M-Z4868 1 CONTROL GRAPHICS PANEL 848M
24 2M-Z4869 1 CONTROL GRAPHICS PANEL 848T
25 G5-848007 1 BODY ASSEMBLY 848M/T/TS/TSCHS
26 VARIOUS 1 NAMEPLATE ALL
N/A 2J-Z4686 1 REGULATOR (5” AND 10”) ALL M/T
N/A 2J-Z5541 1 REGULATOR (4” AND 10”) ALL TS/TSCHS

Part

Number

Per

Unit

Description and Model Designation

1

IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED PAGE

1

INCLUDE MODEL AND SERIAL NUMBER OF

Some items are included for illustrative purposes only and in certain instances may not be available.

Star Manufacturing International, Inc.

16

PARTS LIST March 15, 2006, Rev. A

860-LP Series Gas Griddles

MODEL

Number

Key

Number

1 G5-Z4815 1 FLUE 860M/T/TS/TSCHS
2 G5-Z4817 1 FLUE DIVIDER 860M/T/TS/TSCHS
3 G5-860004 1 GRIDDLE PLATE ASSY COMPLETE 860M
3 G5-860005 1 GRIDDLE PLATE ASSY COMPLETE 860T/TS
3 G5-860006 1 GRIDDLE PLATE ASSY COMPLETE 860TSCHS
4 G5-Z4793 5 BULB CLAMP 860T/TS/TSCHS
5 G5-Z4794 5 BULB COVER 860T/TS/TSCHS
6 G5-Z4795 15 BULB SPRING 860T/TS/TSCHS
7 G5-Z4929 5 ORIFICE BRACKET 860M/T/TS/TSCHS
8 2F-Z4613 5 BURNER 860M/T/TS/TSCHS
9 G5-Z4800 1 SIDE BAFFLE RIGHT ALL 824/36/48/60/72
10 2A-Z4614 4 FOOT ALL 824/36/48/60/72
11 G5-824014 2 WASTE DRAWER ASSY ALL 860/872
12 G5-Z4897 2 DRAWER GUIDE ALL 860/872
13 G5-Z4799 3 PILOT BAFFLE 860TS/TSCHS
14 G5-Z4798 4 BURNER BAFFLE 860M/T
14 G5-Z4798 1 BURNER BAFFLE 860TS/TSCHS
15 G5-Z4900 5 BURNER COVER 860M/T/TS/TSCHS
16 2A-9369 5 ORIFICE FITTING 860M/T/TS/TSCHS
17 2A-Z4930 5 ORIFICE NATURAL 860M/T
17 2A-Z4931 5 ORIFICE PROPANE 860M/T/TS/TSCHS
17 2A-Z5542 5 ORIFICE NATURAL 860TS/TSCHS
18 G5-Z4801 1 SIDE BAFFLE LEFT ALL 824/36/48/60/72
19 2M-Z4873 1 CONTROL GRAPHICS PANEL 860TS/TSCHS
20 2R-Z4997 5 KNOB 860M/T
2R-Z8891 5 KNOB 860TS/TSCHS manuf. after 8/2005
PS-Z9312 5 KNOB SERVICE KIT 860TS/TSCHS manuf. before 8/2005
21 G5-824012 2 CHUTE ASSEMBLY ALL 860/872
22 G5-860008 1 FRONT PANEL ASSEMBLY 860M/T
23 G5-860013 1 FRONT PANEL ASSEMBLY 860TS/TSCHS
24 2M-Z4871 1 CONTROL GRAPHICS PANEL 860M
24 2M-Z4872 1 CONTROL GRAPHICS PANEL 860T
25 G5-860007 1 BODY ASSEMBLY 860M/T/TS/TSCHS
26 VARIOUS 1 NAMEPLATE ALL
N/A 2J-Z4686 1 REGULATOR (5” AND 10”) ALL M/T
N/A 2J-Z5541 1 REGULATOR (4” AND 10”) ALL TS/TSCHS

Part

Number

Per

Unit

Description and Model Designation

1

IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED PAGE

1

INCLUDE MODEL AND SERIAL NUMBER OF

Some items are included for illustrative purposes only and in certain instances may not be available.

Star Manufacturing International, Inc.

17

PARTS LIST March 15, 2006, Rev. A

872-LP Series Gas Griddles

MODEL

Number

Key

Number

1 G5-Z4816 1 FLUE 872M/T/TS/TSCHS
2 G5-Z4817 2 FLUE DIVIDER 872M/T/TS/TSCHS
3 G5-824006 1 GRIDDLE PLATE ASSY COMPLETE 872TSCHS
3 G5-872004 1 GRIDDLE PLATE ASSY COMPLETE 872M
3 G5-872005 1 GRIDDLE PLATE ASSY COMPLETE 872T/TS
4 G5-Z4793 6 BULB CLAMP 872T/TS/TSCHS
5 G5-Z4794 6 BULB COVER 872T/TS/TSCHS
6 G5-Z4795 18 BULB SPRING 872T/TS/TSCHS
7 G5-Z4930 6 ORIFICE BRACKET 872M/T/TS/TSCHS
8 2F-Z4613 6 BURNER 872M/T/TS/TSCHS
9 G5-Z4800 1 SIDE BAFFLE RIGHT ALL 824/36/48/60/72
10 2A-Z4614 4 FOOT ALL 824/36/48/60/72
11 G5-824014 2 WASTE DRAWER ASSY ALL 860/872
12 G5-Z4897 2 DRAWER GUIDE ALL 860/872
13 G5-Z4799 3 PILOT BAFFLE 872TS/TSCHS
14 G5-Z4798 5 BURNER BAFFLE 872M/T
14 G5-Z4798 2 BURNER BAFFLE 872TS/TSCHS
15 G5-Z4900 6 BURNER COVER 872M/T/TS/TSCHS
16 2A-9369 6 ORIFICE FITTING 872M/T/TS/TSCHS
17 2A-Z4930 6 ORIFICE NATURAL 872M/T
17 2A-Z4931 6 ORIFICE PROPANE 872M/T/TS/TSCHS
17 2A-Z5542 6 ORIFICE NATURAL 872TS/TSCHS
18 G5-Z4801 1 SIDE BAFFLE LEFT ALL 824/36/48/60/72
19 2M-Z4876 1 CONTROL GRAPHICS PANEL 872TS/TSCHS
20 2R-Z4997 6 KNOB 872M/T
2R-Z8891 6 KNOB 872TS/TSCHS manuf. after 8/2005
PS-Z9312 6 KNOB SERVICE KIT 872TS/TSCHS manuf. before 8/2005
21 G5-824012 2 CHUTE ASSEMBLY ALL 860/872
22 G5-872008 1 FRONT PANEL ASSEMBLY 872M/T
23 G5-872013 1 FRONT PANEL ASSEMBLY 872TS/TSCHS
24 2M-Z4874 1 CONTROL GRAPHICS PANEL 872M
24 2M-Z4875 1 CONTROL GRAPHICS PANEL 872T
25 G5-872007 1 BODY ASSEMBLY 872M/T/TS/TSCHS
26 VARIOUS 1 NAMEPLATE ALL
N/A 2J-Z4686 1 REGULATOR (5” AND 10”) ALL M/T
N/A 2J-Z5541 1 REGULATOR (4” AND 10”) ALL TS/TSCHS

Part

Number

Per

Unit

Description and Model Designation

1

IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED PAGE

1

INCLUDE MODEL AND SERIAL NUMBER OF

Some items are included for illustrative purposes only and in certain instances may not be available.

Star Manufacturing International, Inc.

18

192021

PARTS LIST March 15, 2006, Rev. A

800M and 800T Series Gas Griddles

MODEL

Key

Number

1 2K-Z4901 1 MANIFOLD 824M/T
2K-Z4902 1 MANIFOLD 836M/T
2K-Z4903 1 MANIFOLD 848M/T
2K-Z4904 1 MANIFOLD 860M/T
2K-Z4905 1 MANIFOLD 872M/T
2 2K-Z4921 2 BURNER FLEX TUBE 824M/T
3 BURNER FLEX TUBE 836M/T
4 BURNER FLEX TUBE 848M/T
5 BURNER FLEX TUBE 860M/T
6 BURNER FLEX TUBE 872M/T
3 2P-1453 1 PIPE PLUG ALL M/T
4 2V-Z4821 2 PILOT BURNER 824T
3 PILOT BURNER 836T
4 PILOT BURNER 848T
5 PILOT BURNER 860T
6 PILOT BURNER 872T
2V-Z4906 2 PILOT BURNER 824M
3 PILOT BURNER 836M
4 PILOT BURNER 848M
5 PILOT BURNER 860M
6 PILOT BURNER 872M
5 2V-6671 2 PILOT VALVE 824M/T
3 PILOT VALVE 836M/T
4 PILOT VALVE 848M/T
5 PILOT VALVE 860M/T
6 PILOT VALVE 872M/T
6 2T-Z4823 2 THROTTLING CONTROL 824T
3 THROTTLING CONTROL 836T
4 THROTTLING CONTROL 848T
5 THROTTLING CONTROL 860T
6 THROTTLING CONTROL 872T
2V-Y8832 2 MANUAL VALVE 824M
3 MANUAL VALVE 836M
4 MANUAL VALVE 848M
5 MANUAL VALVE 860M
6 MANUAL VALVE 872M
7 2A-Z0790 2 FITTING 3/8 CC X 3/8-27 824M
3 FITTING 3/8 CC X 3/8-27 836M
4 FITTING 3/8 CC X 3/8-27 848M
5 FITTING 3/8 CC X 3/8-27 860M
6 FITTING 3/8 CC X 3/8-27 872M
2K-Y7111 2 FITTING 3/8 CC X 1/4 MPT 824T
3 FITTING 3/8 CC X 1/4 MPT 836T
4 FITTING 3/8 CC X 1/4 MPT 848T
5 FITTING 3/8 CC X 1/4 MPT 860T
6 FITTING 3/8 CC X 1/4 MPT 872T

Part

Number

Per

Unit

Description and Model Designation

Number

1

IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED PAGE

1

INCLUDE MODEL AND SERIAL NUMBER OF

Some items are included for illustrative purposes only and in certain instances may not be available.

Star Manufacturing International, Inc.

2223242526

PARTS LIST March 15, 2006, Rev. A

824TS-LP and 824TSCHS-LP Series

MODEL

Number

Key

Number

1 2K-Z4921 2 BURNER FLEX TUBE 824TS/TSCHS
2 2K-2675 2 FITTING 3/8 CC X 3/8 MPT 824TS/TSCHS
3 2P-1453 1 PIPE PLUG 824TS/TSCHS
4 2K-Y5550 3 NIPPLE 3/8 NPT X 1 1/2 824TS/TSCHS
5 2K-2665 1 ELBOW 3/8 NPT 824TS/TSCHS
6 2J-Z4610 2 SOLENOID VALVE 824TS/TSCHS
7 G5-Z4907 2 MOUNTING BRACKET 824TS/TSCHS
8 G5-824019 1 PILOT BRACKET ASSY 824TS/TSCHS
9 G5-824018 1 FLASH TUBE BRACKET ASSY 824TS/TSCHS
10 2J-Z4608 1 PILOT BURNER 824TS/TSCHS
11 2A-Y2017 1 PILOT ORIFICE 824TS/TSCHS
12 2K-Z4920 1 PILOT TUBE FLEX 824TS/TSCHS
13 2J-Z4609 1 THERMOCOUPLE 824TS/TSCHS
14 2K-Z4617 1 REDUCER BUSHING 824TS/TSCHS
15 2K-Z4616 1 INLET PIPE 824TS/TSCHS
16 2K-Z5033 1 UNION 824TS/TSCHS
17 2K-Z4618 1 NIPPLE 3/4 NPT X 2 1/4 824TS/TSCHS
19 2J-Z4607 1 SAFETY VALVE 824TS/TSCHS
20 2V-6671 1 PILOT VALVE 824TS/TSCHS
21 2K-Y4403 1 CLOSE NIPPLE 3/8 NPT 824TS/TSCHS
22 2K-9688 1 TEE 3/8 NPT 824TS/TSCHS
23 2K-Z4612 1 NIPPLE WITH PRESSURE TAP 824TS/TSCHS
24 2T-Z7440 2 ELEC. THERMOSTAT manufactured after 8/2005 824TS/TSCHS
PS-Z9318 2 THERMOSTAT SERVICE KIT manufactured before 8/2005 824TS/TSCHS
25 G5-824015 2 WIRE ASSEMBLY #1 824TS/TSCHS
26 G5-824017 1 WIRE ASSEMBLY 824TS “C” 824TS/TSCHS
27 G5-824016 1 WIRE ASSEMBLY 824TS “L” 824TS/TSCHS
28 2E-Z1858 1 SWITCH 824TS/TSCHS
29 2K-Y2967 1 CORD BUSHING 824TS/TSCHS
30 N2-30409 1 CORD SET 824TS/TSCHS
31 2K-Z4611 1 ELBOW 3/4 NPT 824TS/TSCHS

Part

Number

Per

Unit

Description and Model Designation

1

IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED PAGE

1

INCLUDE MODEL AND SERIAL NUMBER OF

Some items are included for illustrative purposes only and in certain instances may not be available.

Star Manufacturing International, Inc.

27

PARTS LIST March 15, 2006, Rev. A

836TS-LP and 836TSCHS-LP Series

MODEL

Number

Key

Number

1 2K-Z4921 3 BURNER FLEX TUBE 836TS/TSCHS
2 2K-2675 3 FITTING 3/8 CC X 3/8 MPT 836TS/TSCHS
3 2P-1453 1 PIPE PLUG 836TS/TSCHS
4 2K-Y5550 3 NIPPLE 3/8 NPT X 1 1/2 836TS/TSCHS
5 2K-2665 2 ELBOW 3/8 NPT 836TS/TSCHS
6 2J-Z4610 3 SOLENOID VALVE 836TS/TSCHS
7 G5-Z4907 2 MOUNTING BRACKET 836TS/TSCHS
8 G5-824019 2 PILOT BRACKET ASSY 836TS/TSCHS
9 G5-824018 2 FLASH TUBE BRACKET ASSY 836TS/TSCHS
10 2J-Z4608 2 PILOT BURNER 836TS/TSCHS
11 2A-Y2017 2 PILOT ORIFICE 836TS/TSCHS
12 2K-Z4920 2 PILOT TUBE FLEX 836TS/TSCHS
13 2J-Z4609 2 THERMOCOUPLE 836TS/TSCHS
14 2K-Z4617 2 REDUCER BUSHING 836TS/TSCHS
15 2K-Z4616 1 INLET PIPE 836TS/TSCHS
16 2K-Z5033 1 UNION 836TS/TSCHS
17 2K-Z4618 1 NIPPLE 3/4 NPT X 2 1/4 836TS/TSCHS
18 2K-Z5034 1 3/4 NPT TEE 836TS/TSCHS
19 2J-Z4607 2 SAFETY VALVE 836TS/TSCHS
20 2V-6671 2 PILOT VALVE 836TS/TSCHS
21 2K-Y4403 4 CLOSE NIPPLE 3/8 NPT 836TS/TSCHS
22 2K-9688 1 TEE 3/8 NPT 836TS/TSCHS
23 2K-Z4612 1 NIPPLE WITH PRESSURE TAP 836TS/TSCHS
24 2T-Z7440 3 ELEC. THERMOSTAT manufactured after 8/2005 836TS/TSCHS
PS-Z9318 3 THERMOSTAT SERVICE KIT manufactured before 8/2005 836TS/TSCHS
25 G5-824015 3 WIRE ASSEMBLY #1 836TS/TSCHS
26 G5-836017 1 WIRE ASSEMBLY 836TS “C” 836TS/TSCHS
27 G5-836016 1 WIRE ASSEMBLY 836TS “L” 836TS/TSCHS
28 2E-Z1858 1 SWITCH 836TS/TSCHS
29 2K-Y2967 1 CORD BUSHING 836TS/TSCHS
30 N2-30409 1 CORD SET 836TS/TSCHS

Part

Number

Per

Unit

Description and Model Designation

1

IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED PAGE

1

INCLUDE MODEL AND SERIAL NUMBER OF

Some items are included for illustrative purposes only and in certain instances may not be available.

Star Manufacturing International, Inc.

28

PARTS LIST March 15, 2006, Rev. A

848TS-LP and 848TSCHS-LP Series

MODEL

Number

Key

Number

1 2K-Z4921 4 BURNER FLEX TUBE 848TS/TSCHS
2 2K-2675 4 FITTING 3/8 CC X 3/8 MPT 848TS/TSCHS
3 2P-1453 2 PIPE PLUG 848TS/TSCHS
4 2K-Y5550 4 NIPPLE 3/8 NPT X 1 1/2 848TS/TSCHS
5 2K-2665 2 ELBOW 3/8 NPT 848TS/TSCHS
6 2J-Z4610 4 SOLENOID VALVE 848TS/TSCHS
7 G5-Z4907 2 MOUNTING BRACKET 848TS/TSCHS
8 G5-824019 2 PILOT BRACKET ASSY 848TS/TSCHS
9 G5-824018 2 FLASH TUBE BRACKET ASSY 848TS/TSCHS
10 2J-Z4608 2 PILOT BURNER 848TS/TSCHS
11 2A-Y2017 2 PILOT ORIFICE 848TS/TSCHS
12 2K-Z4920 2 PILOT TUBE FLEX 848TS/TSCHS
13 2J-Z4609 2 THERMOCOUPLE 848TS/TSCHS
14 2K-Z4617 2 REDUCER BUSHING 848TS/TSCHS
15 2K-Z4616 1 INLET PIPE 848TS/TSCHS
16 2K-Z5033 1 UNION 848TS/TSCHS
17 2K-Z4618 1 NIPPLE 3/4 NPT X 2 1/4 848TS/TSCHS
18 2K-Z5034 1 3/4 NPT TEE 848TS/TSCHS
19 2J-Z4607 2 SAFETY VALVE 848TS/TSCHS
20 2V-6671 2 PILOT VALVE 848TS/TSCHS
21 2K-Y4403 4 CLOSE NIPPLE 3/8 NPT 848TS/TSCHS
22 2K-9688 2 TEE 3/8 NPT 848TS/TSCHS
23 2K-Z4612 2 NIPPLE WITH PRESSURE TAP 848TS/TSCHS
24 2T-Z7440 4 ELEC. THERMOSTAT manufactured after 8/2005 848TS/TSCHS
PS-Z9318 4 THERMOSTAT SERVICE KIT manufactured before 8/2005 848TS/TSCHS
25 G5-824015 4 WIRE ASSEMBLY #1 848TS/TSCHS
26 G5-848017 1 WIRE ASSEMBLY 848TS “C” 848TS/TSCHS
27 G5-848016 1 WIRE ASSEMBLY 872TS “L” 848TS/TSCHS
28 2E-Z1858 1 SWITCH 848TS/TSCHS
29 2K-Y2967 1 CORD BUSHING 848TS/TSCHS
30 N2-30409 1 CORD SET 848TS/TSCHS

Part

Number

Per

Unit

Description and Model Designation

1

IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED PAGE

1

INCLUDE MODEL AND SERIAL NUMBER OF

Some items are included for illustrative purposes only and in certain instances may not be available.

Star Manufacturing International, Inc.

29

PARTS LIST March 15, 2006, Rev. A

860TS-LP and 860TSCHS-LP Series

MODEL

Number

Key

Number

1 2K-Z4921 5 BURNER FLEX TUBE 860TS/TSCHS
2 2K-2675 5 FITTING 3/8 CC X 3/8 MPT 860TS/TSCHS
3 2P-1453 2 PIPE PLUG 860TS/TSCHS
4 2K-Y5550 5 NIPPLE 3/8 NPT X 1 1/2 860TS/TSCHS
5 2K-2665 3 ELBOW 3/8 NPT 860TS/TSCHS
6 2J-Z4610 5 SOLENOID VALVE 860TS/TSCHS
7 G5-Z4907 3 MOUNTING BRACKET 860TS/TSCHS
8 G5-824019 3 PILOT BRACKET ASSY 860TS/TSCHS
9 G5-824018 3 FLASH TUBE BRACKET ASSY 860TS/TSCHS
10 2J-Z4608 3 PILOT BURNER 860TS/TSCHS
11 2A-Y2017 3 PILOT ORIFICE 860TS/TSCHS
12 2K-Z4920 3 PILOT TUBE FLEX 860TS/TSCHS
13 2J-Z4609 3 THERMOCOUPLE 860TS/TSCHS
14 2K-Z4617 3 REDUCER BUSHING 860TS/TSCHS
15 2K-Z5032 1 INLET PIPE 860TS/TSCHS
16 2K-Z5033 2 UNION 860TS/TSCHS
17 2K-Z4618 4 NIPPLE 3/4 NPT X 2 1/4 860TS/TSCHS
18 2K-Z5034 2 3/4 NPT TEE 860TS/TSCHS
19 2J-Z4607 3 SAFETY VALVE 860TS/TSCHS
20 2V-6671 3 PILOT VALVE 860TS/TSCHS
21 2K-Y4403 6 CLOSE NIPPLE 3/8 NPT 860TS/TSCHS
22 2K-9688 2 TEE 3/8 NPT 860TS/TSCHS
23 2K-Z4612 2 NIPPLE WITH PRESSURE TAP 860TS/TSCHS
24 2T-Z7440 5 ELEC. THERMOSTAT manufactured after 8/2005 860TS/TSCHS
PS-Z9318 5 THERMOSTAT SERVICE KIT manufactured before 8/2005 860TS/TSCHS
25 G5-824015 5 WIRE ASSEMBLY #1 860TS/TSCHS
26 G5-860017 1 WIRE ASSEMBLY 860TS “C” 860TS/TSCHS
27 G5-860016 1 WIRE ASSEMBLY 860TS “L” 860TS/TSCHS
28 2E-Z1858 1 SWITCH 860TS/TSCHS
29 2K-Y2967 1 CORD BUSHING 860TS/TSCHS
30 N2-30409 1 CORD SET 860TS/TSCHS
31 2K-Z4611 2 ELBOW 3/4 NPT 860TS/TSCHS
32 2K-Z5035 1 NIPPLE 3/4 NPT X 22 1/2 860TS/TSCHS

Part

Number

Per

Unit

Description and Model Designation

1

IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED PAGE

1

INCLUDE MODEL AND SERIAL NUMBER OF

Some items are included for illustrative purposes only and in certain instances may not be available.

Star Manufacturing International, Inc.

30

PARTS LIST March 15, 2006, Rev A

872TS-LP and 872TSCHS-LP Series

MODEL

Number

Key

Number

1 2K-Z4921 6 BURNER FLEX TUBE 872TS/TSCHS
2 2K-2675 6 FITTING 3/8 CC X 3/8 MPT 872TS/TSCHS
3 2P-1453 3 PIPE PLUG 872TS/TSCHS
4 2K-Y5550 6 NIPPLE 3/8 NPT X 1 1/2 872TS/TSCHS
5 2K-2665 3 ELBOW 3/8 NPT 872TS/TSCHS
6 2J-Z4610 6 SOLENOID VALVE 872TS/TSCHS
7 G5-Z4907 4 MOUNTING BRACKET 872TS/TSCHS
8 G5-824019 3 PILOT BRACKET ASSY 872TS/TSCHS
9 G5-824018 3 FLASH TUBE BRACKET ASSY 872TS/TSCHS
10 2J-Z4608 3 PILOT BURNER 872TS/TSCHS
11 2A-Y2017 3 PILOT ORIFICE 872TS/TSCHS
12 2K-Z4920 3 PILOT TUBE FLEX 872TS/TSCHS
13 2J-Z4609 3 THERMOCOUPLE 872TS/TSCHS
14 2K-Z4617 3 REDUCER BUSHING 872TS/TSCHS
15 2K-Z5032 1 INLET PIPE 872TS/TSCHS
16 2K-Z5033 2 UNION 872TS/TSCHS
17 2K-Z4618 4 NIPPLE 3/4 NPT X 2 1/4 872TS/TSCHS
18 2K-Z5034 2 3/4 NPT TEE 872TS/TSCHS
19 2J-Z4607 3 SAFETY VALVE 872TS/TSCHS
20 2V-6671 3 PILOT VALVE 872TS/TSCHS
21 2K-Y4403 6 CLOSE NIPPLE 3/8 NPT 872TS/TSCHS
22 2K-9688 3 TEE 3/8 NPT 872TS/TSCHS
23 2K-Z4612 3 NIPPLE WITH PRESSURE TAP 872TS/TSCHS
24 2T-Z7440 6 ELEC. THERMOSTAT manufactured after 8/2005 872TS/TSCHS
PS-Z9318 6 THERMOSTAT SERVICE KIT manufactured before 8/2005 872TS/TSCHS
25 G5-824015 6 WIRE ASSEMBLY #1 872TS/TSCHS
26 G5-872017 1 WIRE ASSEMBLY 872TS “C” 872TS/TSCHS
27 G5-872016 1 WIRE ASSEMBLY 872TS “L” 872TS/TSCHS
28 2E-Z1858 1 SWITCH 872TS/TSCHS
29 2K-Y2967 1 CORD BUSHING 872TS/TSCHS
30 N2-30409 1 CORD SET 872TS/TSCHS
31 2K-Z4611 2 ELBOW 3/4 NPT 872TS/TSCHS
32 2K-Z5035 1 NIPPLE 3/4 NPT X 22 1/2 872TS/TSCHS

Part

Number

Per

Unit

Description and Model Designation

1

IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED PAGE

1

INCLUDE MODEL AND SERIAL NUMBER OF

Some items are included for illustrative purposes only and in certain instances may not be available.

Star Manufacturing International, Inc.

31

32

8

33

la surface de chrome.

5. La négligence de l’entretien courant quotidien sur
la surface de chome.
pourraient endommager et affectent l’exécution de
pierre, écran ou d’autres produits de nettoyage qui
abrasive de nettoyage, brique de gauffreuse,

4. L’utilisation de tout produit chimique ou solution
hors fonction.
causer la surface à la peau, s’écailler, ou ébrécher
font des impressions dans la surface qui pourrait

3. L’abus de tout instrument ou outil qui rayent ou
la section de réglage de déviation.)
surchauffer et décolorer la surface de chrome. (Voir
des unités de gaz en permettant à l’appareil de

2. Sautez les réglages non réglés correctement sur

1. Incorrectement installé.

maltraitée ou soumise aux situations suivantes:
autorisés que la surface de chrome a été abusée ou
International Incorporated ou un de ses représentants
est vide si elle est déterminée par Star Manufacturing
initial de la date de l’installation. Cette garantie limitée
5 ans contre des défauts de fabrication au propriétaire
gril de chrome sont justifi ées pendant une période de
chrome dans son état initial. Toutes les surfaces de
de l’entretien minimum de maintenir la surface de
beaucoup d’années de faire cuire la fi abilité et exige
Votre gril de chrome a été conçu pour vous donner

SURFACE DE GRIL DE CHROME
EXCLUSIONS LIMITÉES DE GARANTIE DE

ATTENTION

34

7

arrêtez le commutateur de puissance.
Tournez les molettes à la plus basse confi guration et

EXTÉRIEURS DE CHROME
CASSEZ L’CAction ET LES MODÈLES

de tour.
Arrêtez les molettes à la position de repos aux brûleurs

D’CÉtranglement
MANUELS DE COMMANDE DE VALVE ET

ARRÊT DURANT LA NUIT MODÈLES

CHAUDE.
LE TIROIR DE REBUT CONTENANT LA GRAISSE
PRENEZ LE SOIN EXTRÊME EN MANIPULANT

ATTENTION

moins une fois par jour.
tiroir devrait être contrôlé et vidé si nécessaire ou au
de l’avant pour nettoyer en tirant le tiroir en avant. Ce
Un tiroir de rebut est situé à l’avant et peut être retiré

DE REBUT TIROIR

5. Maltraiter la surface vide la garantie.

de gril sur la surface de gril.

4. N’utilisez jamais le décapant liquide commercial

3. N’utilisez jamais les laines en acier.

instrument ou un bord pointu de spatule.

2. Ne frappez jamais la surface de gril avec un

ou les abrasifs sur la surface.

1. N’utilisez jamais la renovation, les pierres de gril,

surfaces de chrome).

3. Suivez les étapes 2 et 3 du soin de gril (non
tissu humide propre.
propre extérieur, suivi de l’essuyage avec le
fève que l’ami peut être utilisé pour essuyer
décapant non abrasif et non-chloré tel que la
jour, un tissu et un a humides non-silicated,

2. Après l’érafl ure, pour la fi n du nettoyage de
surface avec un tissu humide si désiré.
pointu de type de rasoir large et essuyez la
régulièrement avec des 4 “ (100mm) racleur

1. Enlevez l’excédent d’huile et la nourriture

de nettoyage devraient être suivies:
empêcher cette condition, les suggestions suivantes
il carbonisera et deviendra diffi cile de retirer. Pour
l’effi cacité. Ne laissez pas la graisse s’accumuler car
de gril industriel de chrome propre et exécuter en haut
petit et l’effort de maintenir ce scintillement extérieur
sur la plaque signalétique.) Elle prend le temps très
“CHS“ à la fi n de la désignation de numéro de type
(Des grils extérieurs de chrome sont identifi és par

SOIN de GRIL (SURFACES de CHROME)

avant, vers le haut de et dehors.
cuisine ordinaire. Le tiroir est retiré en tirant en
et lavent de la même manière qu’une batterie de

3. Du moins une fois par jour, retirent le tiroir de rebut
avec un tissu mou.
du gril. Essuyez l’avant de pupitre de commande
abrasif pour nettoyer le corps d’acier inoxydable

2. Employez un tissu propre et un bon décapant non­en acier entrant dans la nourriture.
les laines en acier en raison du danger des rubans
de gril tandis que le gril est chaud. N’utilisez pas
et reseasoned. Utilisez la pierre de renovation ou
nourriture, le gril devrait être complètement récuré
une accumulation brûler-sur de graisse et de
de rebut est donné pour les raclures. S’ il y a
la graisse et la nourriture excessives. Un tiroir
un racleur ou une spatule fl exible pour enlever

1. Après que chaque utilisation, érafl ent le gril avec

pour la propreté devraient être suivies:
empêcher cette condition, les suggestions suivantes
dure il est extrêmement diffi cile retirer que. Pour
gommeux et carboniser alors dans une substance
est autorisée pour s’accumuler, elle pour un gâteau
attrayant et exécutant en haut l’effi cacité. Si la graisse
Il prend le temps et l’effort très petits de maintenir le gril

SOIN de GRIL (SURFACES de NON-CHROME)

6

35

température choisie.
(minimum), le gril mettra à jour automatiquement la
Après une période de préchauffage de 30 minutes
Placez la molette de cadran à la confi guration désirée.

CUISINE

que le plat de gril "soit cassé dedans."
bâton au gril la cuisine de la surface jusqu’à ce
d’assaisonnement peut, dans une certaine mesure,
Même avec la nourriture soigneuse

être opérationnelle.
et essuyez. La surface de gril devrait maintenant
autre demi-heure, et encore retirez gros excessif
dessus de la zone chaude de cuisine pour une

4. Appliquez un autre fi lm d’huile de cuisine au-

3. Retirez gros excessif et le chiffon propres.
surface de gril.
Ce fi lm devrait rester la demi-heure chaude de
graisse au-dessus du gril faisant cuire la surface.
répandu une couche mince d’huile de cuisine ou de

2. En utilisant un tissu propre, pas une spatule, a
à 350°F (174.0°C).

1. Tournez le cadran de commande de la température

façon suivante:
assaisonnez la surface de chauffage de gril de la
Avant utilisation et après chaque récurage complet,
assaisonné pour empêcher la nourriture de coller.
le gril ait été complètement nettoyé, il devrait être
Nettoyez la surface de gril complètement. Après que

CHROME)
CHAUFFAGE de GRIL (SURFACES de NON­EN ASSAISONNANT LA SURFACE de
INSTRUCTIONS DE FONCTIONNEMENT

de cette prise.
Ne coupez pas ou ne retirez pas la fourche fondante
un réceptacle correctement fondé de trois-fourche.
électrique, l’unité doit être branchée directement à
volt 15 seulement. Pour la protection contre le choc
monophasé à C.A. de cycle de l’ampère 50/60 de
L’unité est conçue pour l’usage sur 120 un circuit
sont équipés d’une trois-fourche fondant la prise.
Des grils extérieurs instantanés d’action et de chrome

DE CHROME SEULEMENT
INSTANTANÉE ET LES MODÈLES EXTÉRIEURS
CONNEXION ÉLECTRIQUE POUR L’CAction

augmenter la fl amme.
le sens contraire des aiguilles d’une montre pour
pour diminuer la taille de fl amme; tournez dans

4. Tournez dans le sens des aiguilles d’une montre
du logement de commande.

3. Une vis d’approche est plac de l’avant ou du côté

être approximativement 1/8" de haut.
sur tous les ports de brûleur. Cette fl amme devrait
Une petite fl amme régulière devrait être visible

2. Tournez le cadran à la confi guration de 200 degrés.
de puissance en arrière.
de maximum la fl amme de brûleur à la commande

1. Placez la commande à la confi guration et à l’attente

satisfaite.
la confi guration de la chaleur de commande a été
fl amme uniforme régulière à travers le brûleur quand
confi guration minimum de fl amme qui fournit une
Les modèles de commande d’étranglement ont une

D’CÉtranglement MODÈLE SEULEMENT
LE RÉGLAGE DE DÉVIATION SUR LA COMMANDE

travers le brûleur entier.
brûleur. La fl amme doit être régulière et même à
est instable ou se soulevante de la surface de

3. N’ouvrez pas l’obturateur à un point où la fl amme
et la fl amme est un bleu dur.
jusqu’à ce que les extrémités jaunes disparaissent
des extrémités jaunes, puis augmentez l’ouverture
jusqu’à ce que la fl amme soit un bleu mou avec

2. Diminuez lentement l’ouverture d’obturateur d’air
plus élevée et observez la fl amme de brûleur.

1. Tournez le bouton de commande à la position la

température de commande ait été satisfaite.
est à la pleine entrée avant que la confi guration de la
complet. Tout réglage doit être fait quand le brûleur
l’obturateur d’air en place après que le réglage soit
faire tout réglage et pour serrer la vis pour verrouiller
côté inférieur du venturi. Desserrez cette vis pour
L’obturateur d’air de brûleur a une vis de blocage du

BRÛLEUR
RÉGLAGE D’CObturateur D’CAir DE

pilote.
thermocouple est entouré par la fl amme
approximativement 3/8" de l’extrémité de
D’CAction Ajustez le pilote tellement

DE THERMOSTAT ET DE CHROME
MODÈLES EXTÉRIEURS INSTANTANÉS

tourné à la haute.
brûleur quand le bouton de commande est
en fournissant toujours l’allumage immédiat de
Ajustez la fl amme aussi basse que possible tout

DE VALVE ET D’CÉtranglement
MODÈLES MANUELS DE COMMANDE

être allumés juste après que le gaz est allumé.
Les grils sont équipés des pilotes debout et devraient

RÉGLAGE PILOTE DE FLAMME

36

5

de puissance.

6. Pour arrêter des brûleurs, arrêtez le commutateur

et placez les thermostats à la position désirée.

5. Mettez en marche le commutateur de puissance
s’est allumé. Répétition pour tous les pilotes.
pendant 60 secondes ou jusqu’ aux séjours pilotes
sûreté. Allumez le pilote. Tenez le bouton de remise

4. Enfoncez et tenez le bouton pilote de remise de

3. Ouvrez la valve principale.
les thermostats à la plus basse confi guration.

2. Arrêtez le commutateur de puissance et tournez
minutes au gaz clair.

1. Arrêtez la valve principale à l’unité et attendez 5

THERMOSTAT ET DE CHROME D’CAction
MODÈLES EXTÉRIEURS INSTANTANÉS DE

hors fonction.

5. Pour arrêter des brûleurs, tournez les molettes à
désirée.

4. Tournez les molettes de brûleur à la position
les pilotes.

3. Ouvrez la valve principale à l’unité et allumez tous
commande.

2. Arrêtez toutes les molettes et soupapes de
minutes au gaz clair.

1. Arrêtez la valve principale à l’unité et attendez 5

D’CÉtranglement MODÈLE
LA COMMANDE MANUELLE DE VALVE ET

6. Réinstallez le panneau avant.
de brûleur.
capots d’orifi ce et réinstallez les vis de support

5. Glissez les brûleurs en arrière au-dessus des
installez les capots d’orifi ce de naturel.

4. Retirez les capots d’orifi ce de gaz propane et
d’orifi ce.

3. Glissez les brûleurs dégagent les capots
l’accès de chambre de combustion couvre.

2. Retirez les vis de support de brûleur au centre de
sur l’avant et le bas.

1. Retirez le panneau avant en retirant les vis plac

comme suit:
les capots de l’orifi ce situés derrière le panneau avant
propane. Pour convertir en gaz de naturel installez
et est expédiée de l’usine pour l’usage avec le gaz
Cette gauffreuse est équipée des capots fi xes d’orifi ce

GAZ NATUREL- CONVERSION

d’alimentation de gaz.
jusqu’à ce que le rapport réel soit établi à la canalisation
empêcher l’entrée de la saleté. Ne retirez pas ce joint
La prise de gaz du gril est scellée à l’usine pour

RACCORD DE LA CANALISATION DE GAZ

amont de la tubulure et à moins de six pieds du gril.
Une valve coupée manuelle devrait être installée en

VANNE D’ARRÊT MANUELLE

après que le gaz est allumé.
des pilotes debout et devraient être allumées juste
soient consommation. Les gauffreuses sont équipées
jusqu’à ce que les huiles et les impuretés de préservatif
Quand la gauffreuse est d’abord allumée, il fumera

ALLUMER DES INSTRUCTIONS

chandelle ou d’autres sources d’allumage.
Ne pas utiliser d’allumettes, la fl amme d’une

ATTENTION

d’eau ou une autre matière acceptable pour ce but.
l’étanchéité, il faut utiliser une solution de savon et
Vérifi er l’étanchéité de toute la tuyauterie. Pour vérifi er

LA VÉRIFICATION LE GAZ FUIT

attacher un indicateur de pression.
1/8" prise de pipe est situé sur la tubulure pour
visibles sur la prise. Réinstallez le chapeau. Un
réinstallez. Les lettres “NAT“ seront maintenant
du centre du régulateur. Inversez la prise et la

10.2cm) en retirant le chapeau rainé ou d’hexa
de l’eau (de 12.7cm) ou 4" colonne de l'eau (de

7. Placez le régulateur de pression à 5" colonne

10“ pression de tubulure de colonne de l’eau.
est expédiées pour l’usage avec le gaz propane avec
au régulateur ne doit pas excéder 1/2 psig. Cette unité
alors reliée à elle. La pression d’approvisionnement
d’admission à l’arrière de l’unité. L’offre de gaz est
chaque gauffreuse. Il devrait être relié dans le tuyau
Un régulateur de pression convertible est équipé de

RÉGULATEUR DE PRESSION DU GAZ

toute impureté interne libre.
tous les tuyaux et raccords doivent être exempts de
fonctionnement. Lors de l’installation de cet appareil,
cet appareil endommagera la vanne et en affectera le
métallique qui entre dans les canalisations de gaz de
AVERTISSEMENT : Toute impureté libre ou particule
composés doivent résister à l’action des gaz propanes.
sur les fi letages mâles des raccords à tuyaux. Ces
composé combiné que modérément et seulement
si elle a la capacité nécessaire. Il ne faut utiliser le
existante, il faut vérifi er cette dernière pour déterminer
l’appareil. S’il faut raccorder l’appareil à la tuyauterie
exigences d’admission de pleine puissance dans
alimentation suffi sante de gaz pour répondre aux
est installée doivent être telles qu’elle fournisse une
La taille de la tuyauterie à gaz et la façon dont elle

TUYAUTERIE À GAZ

37

4

l’utilisation.
être rebranché comme initialement installé avant
débranché pour le service ou le nettoyage qu’il doit
compte qu’il y ait une contrainte sur l’appareil et si
relient le couplage, tout le personnel doit se rendre
est équipé des roulettes et est gaz lié à un rapide
protéger la connexion de ligne de gaz. Si un appareil
d’utiliser des moyens approuvés de passe-fi ls pour
ajoutent environ 6-1/4 “ de taille à l’unité. Soyez sûr
longueur de tube, longueur hors-tout. Les roulettes
la roulette. La jambe de coupe devrait mesurer 19 “
découpage le mur intérieur de tube avant d’installer
jambe en utilisant une scie et un de-burr droits de
soigneusement et découpé le de bas de chaque
de matériel facultatif. Pour d’installation la marque
avec les modèles de stand de plancher ou le stand
Lots de roulettes: Des roulettes peuvent être utilisées

DE STAND.
OU DES JAMBES ET L'ETAGERE FOURNIES
N’INSTALLEZ PAS SANS ATTACHER ES PIEDS

ATTENTION

avec d’autres unités.
ont un réglage de 1-3/4 “ pour la ligne précise et parfaite

être niveau. Unité de niveau en ajustant (4) les pieds qui
plancher qui doivent être vissés dans le corps. L’unité doit
Ce gril est fourni avec 4 pieds ou jambes de stand de

ÉQUILIBRAGE DE L’APPAREIL

38

3

l’appareil. Ne bas boucher cette section.
L’air nécessaire à la combustion entre par le bas de

PRISES D’AIR EN BAS

ATTENTION

CODES LOCAUX, LE CAS ÉCHÉANT.
AU PROPANE CAN/CGA-B149.2 ET AUX
CGA-B149.1 OU AU CODE D’INSTALLATION
D’INSTALLATION AU GAZ NATUREL CAN/
ÊTRE CONFORME AU CODE COURANT
AU CANADA, L’INSTALLATION DOIT

être fournis.
Les vivres pour provision de l'air adéquate doivent

LA PROVISION DE L'AIR

codes locaux.
L’installation d’échappement doit se conformer aux
fi ltres ou n’importe quel autre matériel combustible.
48 “ sera fournie entre le dessus de l’appareil et les
de fl amme. Une distance verticale pas moins de de
effi cace d’échappement avec des fi ltres de preuve
la fumée et devraient être installés sous un capot
Les grils créent en soi beaucoup de la chaleur et de

ÉPUISEZ LE BALDAQUIN

pressions égales à ou de moins que ½ PSIG.
de pression de la tuyauterie d’alimentation de gaz à des

sa vanne d’arrêt manuelle individuelle lors des essais
être isolés de la tuyauterie d’alimentation du gaz en fermant
PSIG. Cet appareil et son régulateur de pression doivent
tuyauterie en question à des pressions en dessus de ½
d’alimentation du gaz lors des essais de pression de la
d’arrêt individuelles doivent être débranchés de la tuyauterie
Cet appareil, son régulateur de pression et ses vannes

gaz pour l’approbation de l’installation fi nale.
locales. En tout cas, il faut appeler votre société du
installations de gaz et vos exigences de gaz
d’installation qualifi ée. Ils doivent connaître les
de faire installer cet appareil par une agence
Pour votre propre protection, on vous recommande

contrainte au connecteur.
retenants de garder contre la transmission de la
Il doit également être installé avec des moyens
conforme à la norme ANSI Z21.41 ou au CAN1-6.9.
ou au CAN/CGA-6.16 et à un dispositif rapide étant
connecteur étant conforme à la norme ANSI Z21.69
il doit être installé avec les roulettes fournies, un
Quand cet appareil est installé avec des roulettes,

-IMPORTANT-

COMPAGNIE DE GAZ LOCALE.
RÈGLES ET RÉGLEMENTATIONS DE LA
DES ÉTATS-UNIS ET À TOUTES LES
"ANSI Z223.1 - TOUTE DERNIÈRE ÉDITION"
CODE NATIONAL DE GAZ COMBUSTIBLE
L’installation de l’appareil doit se conformer au

pour l’exécution appropriée et l’entretien.
dégagement adéquat devrait également être donné
et au moins 6 “ (16cm) des côtés et du dos. Le
moins 48 “ (120cm) à partir du dessus de l’appareil
matériel combustible et non-combustible doit être au
sur les countertops non-combustibles seulement. Le

ET CLAIRE DES COMBUSTIBLES! Pour l’usage
MAINTENEZ LA RÉGION D’CAppareils LIBRE

extérieures de l’unité.
de gauffreuse et nettoyez complètement les surfaces
l’éclairage. Éliminez le plastique protecteur du plat
protection et d’emballage à partir de l’unité avant
Soyez sûr d’enlever tout le matériel de papier de

Intoxiquer - La Conversion.
facilement être converties en naturel. Voir Le Naturel
unité est expédiées pour le gaz propane et peuvent
l’usage sur le gaz naturel ou de propane. Cette
Des grils de série d’Ultra-Max sont équipés pour

emplacements de service de traiteur.
l’usage directement par le grand public dans des
consommateur dans et autour de la maison ni pour
en son exécution et n’est pas vendu pour l’usage du
seulement par le personnel qualifi é et expérimenté
Ce matériel est conçu et vendu pour l’usage commercial

ATTENTION

NOTIFICATION

DONNÉES GÉNÉRALES D’INSTALLATION

39

2

plus rapide.
questions qui peuvent se poser. Veuillez avoir votre numéro et numéro de série de type pour un service
Star (1-800-807-9054) disponible pendant des heures de travail normales pour répondre à toutes les
Référez-vous à la liste autorisée de centre commercial équipée d'unité. Le service SVP de service de
Entrez en contact avec votre agent autorisé local de service pour le service ou l'entretien requis.

ENTRETIEN ET RÉPARATIONS

correspondants pour l’équipement précédemment acheté.
aux améliorations, aux additions ou aux remplacements
telles révisions ne ont pas droit l’acheteur aux changements,
conception de produits sans communication préalable. De
Star se réserve le droit de changer des caractéristiques et la

NOTIFICATION

responsabilité.
par usine véritable de Star soulage le fabricant de toute la
Employer n’importe quelle partie autre que les pièces fournies

NOTIFICATION

MAINTENEZ CE MANUEL POUR LA FUTURE RÉFÉRENCE

accompagnant l’appareil.
instructions importantes de fonctionnement et d’entretien du manuel
Ce symbole est prévu pour alerter l’utilisateur à la présence des

SYMBOLE DE SÛRETÉ

40

fournisseur local de gaz.
sent le gaz. Obtenez les instructions du
détaillées d’être suivi en cas que l’opérateur
emplacement en avant, des instructions
En outre, là devrait être signalé, dans un

d’installer et utiliser cet appareil.
aéré. Référez-vous aux instructions avant
et utilisé seulement dans l’espace bien­installé selon des règlements actuels
AVERTISSEMENT: Cet appareil sera

appareil.
proximité de ceci ou d’aucun autre
vapeurs ou liquides inflammables à
ou n’utilisez pas l’essence ou d’autres
POUR VOTRE SÛRETÉ: N’enregistrez pas

d’installer ou entretenir ce matériel.
et d’entretien complètement avant
les instructions d’installation, d’opération
matériels, des dommages ou la mort. Lisez
l’entretien peuvent causer des dégats
le réglage, le changement, le service ou
AVERTISSEMENT: L’installation inexacte,

2M-Z7924 Rev. A 3/15/2006

et d’opération

d’installation

Instructions

MODELES

Fax: [phone]
Phone: [phone]

St. Louis, MO 63143
10 Sunnen Drive

International Inc.
Manufacturing
Star

872M-LP 872T-LP 872TS-LP 872TSCHS-LP
860M-LP 860T-LP 860TS-LP 860TSCHS-LP
848M-LP 848T-LP 848TS-LP 848TSCHS-LP
836M-LP 836T-LP 836TS-LP 836TSCHS-LP
824M-LP 824T-LP 824TS-LP 824TSCHS-LP

GRILS A GAZ ULTRA-MAX