Star Manufacturing 530TD SERIES, 530TED SERIES Operation Manual

<![if ! IE]>

<![endif]>®

<![if ! IE]>

<![endif]>®

530TD

<![if ! IE]>

<![endif]>®

®

DEEP FAT

FRYER

MODEL

530TD & 530TED SERIES

Installation and

Operation

Instructions

2M-Z6600 REV. D 8/19/2011

SAFETY SYMBOL

These symbols are intended to alert the user to the presence of important operating and maintenance instructions in the manual accompanying the appliance.

RETAIN THIS MANUAL FOR FUTURE REFERENCE

NOTICE

Using any part other than genuine Star factory supplied parts relieves the manufacturer of all liability.

Star reserves the right to change speciications and product design without notice. Such revisions do not entitle the buyer to corresponding changes, improvements, additions or replacements for previously purchased equipment.

Due to periodic changes in designs, methods, procedures, policies and regulations, the speciications contained in this sheet are subject to change without notice. While Star International Holdings Inc., Company exercises good faith efforts to provide information that is accurate, we are not

responsible for errors or omissions in information provided or conclusions reached as a result of using the speciications. By using the information provided, the user assumes all risks in connection with such use.

MAINTENANCE AND REPAIRS

Contact your local authorized service agent for service or required maintenance.

Please record the model number, serial number, voltage and purchase date in the area below and have it ready when you call to ensure a faster service.

Model No.

Serial No.

Voltage

Purchase Date

Authorized Service Agent Listing

Reference the listing provided with the unit

or
for an updated listing go to:
Website:	www.star-mfg.com
E-mail	[e-mail]
Service Help Desk
Business	8:00 am to 4:30 p.m. Central Standard Time
Hours:
Telephone:	(800) 64-78 7 Local (3 4) 684-6303
Fax:	(800) 396677 Local (3 4) 78 - 7 4
E-mail	[e-mail]
	[e-mail]
	[e-mail]
Website:	www.star-mfg.com

Mailing Address: Star International Holdings Inc., Company

0 Sunnen Drive

St. Louis, MO 63 43

U.S.A

SPECIFICATIONS:

530TD

Type: TWIN POT ELECTRIC FRYERS

208V, 8,638 watts, 41.5 amp 240V, 11,500 watts, 47.5 amp

Approximate weight: installed - 69 Lb s (31.3 kg), shipping - 81 Lbs (36.7 kg)

Dimensions: 24" - Width, 24" - Depth, 16 3/4" - Height (61 cm-width, 61 cm-depth, 42.5 cm-weight)

530TED

Type: TWIN POT ELECTRIC FRYERS

208V, 6,910 watts, 33.2 amp 240V, 9,200 watts, 38.3 amp

Approximate weight: installed - 69 Lb s (31.3 kg), shipping - 81 Lbs (36.7 kg)

Dimensions: 24" - Width, 24" - Depth, 16 3/4" - Height (61 cm-width, 61 cm-depth, 42.5 cm-weight)

GENERAL INSTALLATION DATA

This equipment is designed and sold for commercial use only by personnel trained and experienced

in its operation and is not sold for consumer use in and around the home nor for use directly by the CAUTION general public in food service locations.

Before using your new equipment, read and understand all the instructions & labels associated with the unit prior to putting it into operation. Make sure all people associated with its use understand the units operation & safety before they use the unit.

All shipping containers should be checked for freight damage both visible and concealed. This unit has been tested and carefully packaged to insure delivery of your unit in perfect condition. If equipment is received in damaged condition, either apparent or concealed, a claim must be made with the delivering carrier.

Concealed damage or loss - if damage or loss is not apparent until after equipment is unpacked, a request for inspection of concealed damage must be made with carrier within 5 days. Be certain to retain all contents plus external and internal packaging materials for inspection. The carrier will make an inspection and will supply necessary claim forms.

WARNING: Improper installation, adjustment, alteration, service or maintenance can cause property damage, injury or death. Read the installation, operating and maintenance instructions thoroughly before installing or servicing the equipment.

This fryer is equipped for the voltage and wattage indicated on the nameplate mounted on the lower right corner of the element housing. It is designed for use on alternating current (AC) only. It is intended for use by properly trained personnel only.

DO NOT CONNECT TO DIRECT CURRENT (DC)

WARNING The installation of the appliance should conform to the:

NATIONAL ELECTRIC CODE AND ALL LOCAL ELECTRIC CODES AND ORDINANCES AND THE LOCAL ELECTRIC COMPANY RULES AND REGULATIONS

For your protection we recommend that a qualiied electrician install this appliance. He should be

familiar with electrical installations and all electrical codes. Proper connections and power supply are essential for eficient performance. The external wiring should be in conduit or an approved type of lexible cable suitable for operation at 90° C (194° F) and of a proper size to carry the load. The

supply circuit should be properly fused and equipped with a means of disconnection, as required by local electrical code. THE BODY OF THE APPLIANCE SHOULD BE GROUNDED - DO NOT

GROUND TO A GAS SUPPLY LINE. Four legs are provided and should be installed for ease of cleaning. Level unit by adjusting the (4) feet which have an adjustment of 1-3/8" (34.92 mm) for

accurate leveling and perfect line-up with other units.

POWER SUPPLY

Models 530TD and 530TED are wired at the factory for operation on a single phase power supply. For speciic wiring, check the wiring diagram.

3

OPERATING INSTRUCTIONS

PLACE THE LAMINATED WARNING SIGN SUPPLIED WITH THE FRYER IN AN AREA VISIBLE TO THE FRYER OPERATOR.

CAUTION CLEAN KETTLE BEFORE USING

Take out baskets, push and hold element catch, lift up on element lift handle until elements lock in a vertical position, and remove kettle. The kettle can be cleaned in a sink like any other pot or container.

ADDING FAT

Replace kettle and swing the element down, making fryer ready for use. Add fat. Each kettle has a

5 lb. fat capacity. A fat level line on the rear of the kettle will guide you in determining the minimum cold fat level. A higher fat level can be used when frying bulky foods, such as chicken or ish cakes.

The fat level should be chosen carefully so that the foaming action of the fat does not spill out of the kettle. If solid shortening is used, pack carefully around the elements.

CONTROLS

	1. ON/OFF TWO-POLE SWITCH - Located on the front panel is a two-pole switch which turns power
CAUTION	on or off. An indicator light (Power On) is located on the control housing.

2.THERMOSTAT CONTROL - Located on the Control Housing, this control allows you to select the desired frying temperature. A signal light "Heating" indicates when the element is on. When the light goes off, the desired temperature has been reached.

3.HI-LIMIT THERMOSTAT - Should fat temperatures reach 450° F (230° C), this control will shut off

the power to the heating elements. The unit will still have power. The fat temperature must cool to 400° F (202.4° C) and the manual reset button located on the back panel of the control housing must be pressed to restore operation. Should the hi-limit control activate twice in succession, the primary thermostat should be checked for malfunction by a qualiied service technician. Each pot is equipped with its own HI-LIMIT THERMOSTAT.

FRYING

After fat has been added, turn the switch on and set the thermostat at 200° F (92.4° C). After the fat has melted, turn the thermostat to the desired setting. Included in this instruction booklet is a frying

chart and some helpful hints on fat use. After the selected fat temperature has been reached, slowly lower half illed baskets into the fat. Do not overload baskets as this causes foods to be improperly

fried.

NOTE: Baskets should be allowed to drain after frying cycle. The kettle handles serve as basket hangers.

IDLING

During idle periods turn thermostat control to approximately 200° F (92.4° C). The fast recovery fryers can be brought up to frying temperature in a matter of minutes. Lowering the temperature

during idle periods saves energy costs and prolongs fat life.

DRAINING KETTLE

Turn switch to "OFF". Raise element to the irst stop and allow to drain. Raise the element to the vertical position and siphon the oil out of the kettle.

DO NOT ATTEMPT TO REMOVE THE KETTLE FILLED WITH HOT OIL. CONTACTING HOT

OIL CAN RESULT IN SEVERE INJURIES OR DEATH.

CAUTION If you do not have a siphon, order one from your dealer or dip the oil out and strain into a container. After oil has been removed, remove the kettle and clean.

INAPPROPRIATE USE DUE TO A LACK OF COMMON SENSE MAY RESULT IN CAUTION PRODUCT DAMAGE OR PERSONAL INJURY.

CLEANING THE EXTERIOR

The exterior surfaces can be cleaned by regularly wiping with a soft cloth. Any discoloration can be removed with a non-abrasive cleaner.

4