Star Manufacturing 12S, 12 Parts List
Star
Manufacturing
International Inc.
10 Sunnen Drive
St. Louis, MO 63143
Phone: (314) 781-2777
FAX: (314) 781-3636
HOT DOG CHROME ROLLER GRILLHOT DOG CHROME ROLLER GRILL
HOT DOG CHROME ROLLER GRILL
HOT DOG CHROME ROLLER GRILLHOT DOG CHROME ROLLER GRILL
MODELS 12, 25, 25X, 40, 45, 45X and 75MODELS 12, 25, 25X, 40, 45, 45X and 75
MODELS 12, 25, 25X, 40, 45, 45X and 75
MODELS 12, 25, 25X, 40, 45, 45X and 75MODELS 12, 25, 25X, 40, 45, 45X and 75
HOT DOG SILVERSTONE ROLLER GRILLHOT DOG SILVERSTONE ROLLER GRILL
HOT DOG SILVERSTONE ROLLER GRILL
HOT DOG SILVERSTONE ROLLER GRILLHOT DOG SILVERSTONE ROLLER GRILL
MODELS 12S, 25S, 25SX, 40S, 45S, 45SX and 75SMODELS 12S, 25S, 25SX, 40S, 45S, 45SX and 75S
MODELS 12S, 25S, 25SX, 40S, 45S, 45SX and 75S
MODELS 12S, 25S, 25SX, 40S, 45S, 45SX and 75SMODELS 12S, 25S, 25SX, 40S, 45S, 45SX and 75S
2M-Y4358 Rev. T 5-30-97
Installation
and
Operating
Instructions
Model 25
1
GENERAL OPERATING PROCEDURES
CAUTION
This equipment is designed and sold for
commercial use only by personnel trained and
experienced in its operation and is not sold for
consumer use in and around the home nor for
use directly by the general public in food service
locations. For equipment to be used by the
general public, please contact the factory.
INSTALLATION:
This grill is equipped for the voltage shown on
the nameplate. It will operate on alternating
current only, however, the correct voltage must
be applied.
CAUTION
DO NOT CONNECT TO DIRECT
CURRENT (DC).
For flexibility, all models of roller grills, excluding
the 12, are divided into two independently controlled
heat sections. The right control knob controls the
rear cooking section and the left control knob
controls the front cooking section. The 12 and 12S
grills have only one heating section.
A signal light is provided next to each control
knob to give a visual check if one or both sections
are turned on.
Each section is controlled by means of a rotary
switch with positions marked at OFF-HIGHMEDIUM and LOW. On MEDIUM for all models
except the 12 and 12S 230CE, it is normal for
every other roller to be unheated. The 12 and
12S 230CE uses an infinite control which varies
heat on all rollers.
Before cooking for the first time, wash all rollers
with mild detergent solution and then wipe with a
clean wet cloth.
Hot dogs should be kept refrigerated until ready
for use. Always use hot dogs or sausages made
for grilling.
Connection Load:
Model 12, 12S 120V -610 Watts
Model 12, 12S 230CE- - 530 Watts
Model 25, 25S, 25SX, 25X- 1196 Watts
Model 40, 40S - 1636 Watts
Model 45, 45S, 45SX, 45X- 1696 Watts
Model 75, 75S -2656 Watts
The grill should be connected to a wall type
receptacle, a direct line or separate circuit. A
direct line or separate circuit is preferred. If the
grill is connected on a line already overloaded, it
will not operate properly. When installed, the
unit should be level. Optional 4 inch adjustable
legs are available.
NSF requires that perishable foods be kept at
o
140
F or above during serving periods. Do not
keep hot dogs on the LOW setting for more than
two hours. If held for more than two hours they
must be transferred to HIGH or MEDIUM heated
zone for cooking and serving.
CAUTION
USE ONLY PLASTIC OR COATED
UTENSILS FOR HANDLING THE HOT
DOGS. METAL WILL SCRATCH THE
ROLLERS. WHEN COOKING, DO NOT
TRANSFER HOT DOGS FROM HIGH TO
LOW AS THEY MAY SHRINK. DO NOT
OPERATE GRILL WITHOUT GREASE
PAN IN PLACE.
2
Cooking time will vary depending on starting
temperature and quality of the product. For best
results follow the cooking systems shown below.
1. Busy periods - Set both controls on HIGH and
fill to capacity.
2. Medium periods - Set control to HIGH to
cook hot dogs. Reduce heat to MEDIUM as
needed.
3. For all models except the 12 and 12S 230CE
preheat hot dogs on LOW. Medium is used
for preheating the 12 and 12S 230CE. Turn
heat to HIGH for cooking as needed.
CLEANING:
Remove all hot dogs. Turn control to HIGH and
allow rollers to get hot. Clean rollers with a
clean wet cloth. Wipe from the outside ends
towards the center of the rollers. Do not force
grease into the roller end bearings.
Turn the grill off and remove the grease tray by
pulling forward on the front edge. Clean the
entire unit daily to insure long life and satisfactory
performance as well as to maintain an attractive
appearance. The exterior should be kept bright
and attractive by using a mild detergent or nonabrasive cleaner.
CAUTION
DO NOT USE SHARP EDGES ON
SILVERSTONE COATING - SCRAPES
WILL VOID THE WARRANTY. NEVER
USE STEEL WOOL OR ABRASIVE
CLEANERS TO CLEAN ROLLERS AS
THIS WILL DAMAGE THE FINISH AND
POSSIBLY DAMAGE THE BEARINGS.
MAINTENANCE AND REPAIRS
Contact the factory, a service representative or a
local service company for service or required
maintenance.
RETAIN THIS MANUAL FOR FUTURE REFERENCE
PART NO. 2M-Y4358 REV. S 4-24-97
3
Loading...