Sta-Rite TS5L Installation Manual
TS5L
UY Connectors
TS5L
UY Connectors
APPLICATION:
Temperature Sensor used with Compool pool and spa control systems.
This Sensor may be used for Water or Solar. With the Cp3800 Control
system family it may also be used for Freeze protection.The UY wire
connectors are for 22-26 guage wires and designed for indoor or
outdoor use.
KIT INCLUDES:
QTY. DESCRIPTION
1 Temperature Sensor, Linear (with 25 feet cable)
2 UY Wire Splicing Connectors
Pentair Water Pool and Spa, Inc.
1620 Hawkins Ave., Sanford, NC 27330 • (919) 566-8000
10951 W. Los Angeles Ave., Moorpark, CA 93021
P/N 9420590 Rev.A 2-16-07 P/N 9420590 Rev.A 2-16-07
• (805) 553-5000
APPLICATION:
Temperature Sensor used with Compool pool and spa control systems.
This Sensor may be used for Water or Solar. With the Cp3800 Control
system family it may also be used for Freeze protection.The UY wire
connectors are for 22-26 guage wires and designed for indoor or
outdoor use.
KIT INCLUDES:
QTY. DESCRIPTION
1 Temperature Sensor, Linear (with 25 feet cable)
2 UY Wire Splicing Connectors
Pentair Water Pool and Spa, Inc.
1620 Hawkins Ave., Sanford, NC 27330 • (919) 566-8000
10951 W. Los Angeles Ave., Moorpark, CA 93021
• (805) 553-5000
INSTALLATION:
INSTALLATION:
Water Temperature Sensor Replacement Parts
1. Remove old Sensor and cable.
2. Use existing clamp to install new Sensor into plumbing
3. Run cable to the Power Center and connect to existing WATER
temperature screw terminals: RED to (+) and GREEN to (–).
Solar Temperature Sensor
1. For unglazed panels, fasten Sensor next to solar panels. For
glazed panels, suspend Sensor between collector and glazing.
2. Run a 2-conductor 22 AWG cable from the sensor to the Power
Center. At the Sensor, cut off excess cable and use crimp
connectors (included) to provide waterproof connections. Insert
the 2 wires to be connected into the connector and squeeze the
connector with a pair of pliers. NOTE: Do not strip wires.
3. At the Power Center circuit board, connect Sensor wires to the
SOLAR screw terminals, RED to (+) and GREEN to (–).
Freeze Temperature Sensor for Cp3800, Cp3600, Cp3400, Cp3810,
Cp3820 and Cp3830
1. Cut cable to approximately 2 ft. so that Sensor will hang from
the bottom of Power Center. If necessary, Sensor may be
located further from Power Center.
Water Temperature Sensor Replacement Parts
1. Remove old Sensor and cable.
2. Use existing clamp to install new Sensor into plumbing
3. Run cable to the Power Center and connect to existing WATER
temperature screw terminals: RED to (+) and GREEN to (–).
Solar Temperature Sensor
1. For unglazed panels, fasten Sensor next to solar panels. For
glazed panels, suspend Sensor between collector and glazing.
2. Run a 2-conductor 22 AWG cable from the sensor to the Power
Center. At the Sensor, cut off excess cable and use crimp
connectors (included) to provide waterproof connections. Insert
the 2 wires to be connected into the connector and squeeze the
connector with a pair of pliers. NOTE: Do not strip wires.
3. At the Power Center circuit board, connect Sensor wires to the
SOLAR screw terminals, RED to (+) and GREEN to (–).
Freeze Temperature Sensor for Cp3800, Cp3600, Cp3400, Cp3810,
Cp3820 and Cp3830
1. Cut cable to approximately 2 ft. so that Sensor will hang from
the bottom of Power Center. If necessary, Sensor may be
located further from Power Center.
2. At the Power Center circuit board, connect Sensor wires to the
FREEZE screw terminals.
3. If the Sensor will be located at a distance from the Power
Center, run a 2-conductor cable between the Sensor and the
Power Center. At the Sensor, use crimp connectors (included)
to provide waterproof connections. Before making connections,
cut off stripped ends of cable. Insert the 2 wires to be connected
into the connector and squeeze the connector with a pair of
pliers. NOTE: Do not strip wires.
Pentair Water Pool and Spa, Inc.
1620 Hawkins Ave., Sanford, NC 27330 • (919) 566-8000
10951 W. Los Angeles Ave., Moorpark, CA 93021
P/N 9420590 Rev.A 2-16-07 P/N 9420590 Rev.A 2-16-07
• (805) 553-5000
2. At the Power Center circuit board, connect Sensor wires to the
FREEZE screw terminals.
3. If the Sensor will be located at a distance from the Power
Center, run a 2-conductor cable between the Sensor and the
Power Center. At the Sensor, use crimp connectors (included)
to provide waterproof connections. Before making connections,
cut off stripped ends of cable. Insert the 2 wires to be connected
into the connector and squeeze the connector with a pair of
pliers. NOTE: Do not strip wires.
Pentair Water Pool and Spa, Inc.
1620 Hawkins Ave., Sanford, NC 27330 • (919) 566-8000
10951 W. Los Angeles Ave., Moorpark, CA 93021
• (805) 553-5000
Loading...