Sta-Rite 2 TR100 C Installation Manual

®

TANDEM SYSTEM PLUMBING KIT

®

INSTALLATION, OPERATION & SERVICE MANUAL

PENTAIR POOL PRODUCTS

CORPORA

AIR

PENT

TE OFFICE

Sanford, NC

[phone]

POOL PRODUCTS

k, CA

par

Moor

[phone]

P/N 152992 REV. A

®

TANDEM SYSTEM PLUMBING KIT PAGE 2

For more information on Pentair Pool Products, visit our website at
www.pentairpool.com or contact our factories at 800-831-7133.

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

Pentair Pool Products

1620 Hawkins Ave.
Sanford, NC 27330

919-566-8000

Fax: [phone]

Pentair Pool Products

10951 W. Los Angeles Ave.

Moorpark, CA 93021

805-523-2400

Fax: [phone]

TANDEM SYSTEM PLUMBING KIT PAGE 3

T

ANDEM TRITON II TR 100 C & TR 100 C3 FILTER INSTALLATION

2 TR100 C

or

2 TR100 C3

3 TR100 C

or

3 TR100 C3

4 TR100 C

or

4 TR100 C3

5 TR100 C

or

5 TR100 C3

NOTES

2 TR140 C

or

2 TR140 C3

3 TR140 C

or

3 TR140 C3

4 TR140 C

or

TR140 C3

4

5 TR140 C

or

5 TR140 C3

TR140 C

6

or

TR140 C3

6

TANDEM

ON II TR 140 C & TR 140 C3 FIL

TRIT

TER INSTALLATION

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

TANDEM SYSTEM PLUMBING KIT PAGE 4

MANIFOLD SIZE SCH 40

3” 4” 6”

NUMBER OF

FILTERS KIT # QTY. KIT # QTY. KIT # QTY.

2 FILTERS 14-6400 14-7400 1 14-6402 14-7402 1

C C-3” C C-3” C C-3”

3 FILTERS

4 FILTERS

5 FILTERS

6 FILTERS

3” 4” 6”

NUMBER OF

FILTERS KIT # QTY. KIT # QTY. KIT # QTY.

C

2 FILTERS 14-6401 14-7401 1 14-6403 14-7403 1

C-3”

14-6402 14-7402 1 14-6404 14-7404 1

14-6406 14-7406 1 14-6408 14-7408 1

14-6402 14-7402 1 14-6404 14-7404 1

14-6406 14-7406 2 14-6408 14-7408 2

14-6404 14-7404 1

14-6408 14-7408 3

14-6404 14-7404 1

14-6408 14-7408 4

MANIFOLD SIZE SCH 80

C C-3” C C-3”

NOTES

TERS

3 FIL

4 FILTERS

5 FILTERS

6 FILTERS

14-6403 14-7403 1 14-6405 14-7405 1

14-6409

14-6407

14-6403 14-7403 1 14-6405 14-7405 1

14-6407 14-7407 2 14-6409 14-7409 2

14-7407

1

14-6405 14-7405 1

14-6409

14-6405 14-7405 1

14-6409 14-7409 4

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

14-7409 1

14-7409 3

TANDEM SYSTEM PLUMBING KIT PAGE 12

14

13

15

16

17

22

19

23

18

24

20

21

18

24

20

21

!

!

6” SINGLE FILTER KIT SCHEDULE 40

(14-7408)

Item Pentair Part# AP PN Size Description Sch. Qty

17 15-0080 10401-530 6 X 3 Socket Reducer Tee 40 2

19 15-0075 10427-030 3” Spig x Soc 45 Str. Elbow 40 2

20 15-3014 10463-528 6 X 2 Socket Reducer Saddle 40 3

21 15-2989 10851-020

2” Flg. One-Piece Socket - 150 lb.

80 1

22 15-0056 10856P-030 3” Flg. VS, Spigot - 150 lb. 80 2

23 15-0082 REQ.

3” Bolt Pack - Tank/Flg. Hdwr w/Gasket (#4)

1

Includes 8-5/8 x 3-1/4” hex head bolts, 8-5/8” nuts, 16-5/8” washers

10870-030

and 2 - 3” Neoprene FF Flg. Gaskets

15-2992

Installation, Operation & Service Manual

1

6” SINGLE FILTER KIT SCHEDULE 80

(14-7409)

Item Pentair Part# AP PN Size Description Sch. Qty

17 15-0081 10801-530 6 X 3 Socket Reducer Tee 80 2

19 15-0077 1827-030 3” Spig x Soc 45 Str. Elbow 80 2

20 15-3014 10463-528 6 X 2 Socket Reducer Saddle 40 3

21 15-2989 10851-020

2” Flg. One-Piece Socket - 150 lb.

80 1

22 15-0056 10856P-030 3” Flg. VS, Spigot - 150 lb. 80 2

23 15-0082 REQ.

3” Bolt Pack - Tank/Flg. Hdwr w/Gasket (#4)

1

Includes 8-5/8 x 3-1/4” hex head bolts, 8-5/8” nuts, 16-5/8” washers

10870-030

and 2 - 3” Neoprene FF Flg. Gaskets

15-2992

Installation, Operation & Service Manual

1

!

!

!

!

4” SINGLE FILTER KIT SCHEDULE 40

(14-7406)

I

tem Pentair Part# AP PN Size Description Sch. Qty

1

7 15-0078 10401-420 4 X 3 Socket Reducer Tee 40 2

1

9 15-0075 10427-020 3” Spig x Soc 45 Str. Elbow 40 2

20 15-3010 10478-020 4 X 2 Socket Reducer Saddle 40 3

21 15-2989 15-2989

2” Flg. One-Piece Socket - 150 lb.

80 1

2

2 15-0056 10463-420 3” Flg. VS, Spigot - 150 lb. 80 2

2

3 15-0082 10851-020

3

” Bolt Pack - Tank/Flg. Hdwr w/Gasket (#4)

1

I

ncludes 8-5/8 x 3-1/4” hex head bolts, 8-5/8” nuts, 16-5/8” washers

1

0870-030

a

nd 2 - 3” Neoprene FF Flg. Gaskets

6

15-2992

Installation, Operation & Service Manual

1

4” SINGLE FILTER KIT SCHEDULE 80

(14-7407)

Item Pentair Part# AP PN Size Description Sch. Qty

17 15-0079 10801-422 4 X 3 Socket Reducer Tee 80 2

1

9 15-0077 1827-030 3” Spig x Soc 45 Str. Elbow 80 2

2

0 15-3010 10463-420 4 X 2 Socket Reducer Saddle 40 3

21 15-2989 10851-020

2” Flg. One-Piece Socket - 150 lb.

80 1

22 15-0056 10856P-030 3” Flg. VS, Spigot - 150 lb. 80 2

2

3

15-0082 REQ.

3” Bolt Pack - Tank/Flg. Hdwr w/Gasket (#4)

1

Includes 8-5/8 x 3-1/4” hex head bolts, 8-5/8” nuts, 16-5/8” washers

10870-030

a

nd 2 - 3” Neoprene FF Flg. G

askets

1

5-2992

I

nstallation, Operation & Service Manual

1

6” SINGLE FILTER KIT SCHEDULE 40

(14-7408)

I

tem Pentair Part# AP PN Size Description Sch. Qty

1

7 15-0080 10401-530 6 X 3 Socket Reducer Tee 40 2

1

9 15-0075 10427-030 3” Spig x Soc 45 Str. Elbow 40 2

20 15-3014 10463-528 6 X 2 Socket Reducer Saddle 40 3

21 15-2989 10851-020

2” Flg. One-Piece Socket - 150 lb.

80 1

2

2 15-0056 10856P-030 3” Flg. VS, Spigot - 150 lb. 80 2

2

3 15-0082 REQ.

3

” Bolt Pack - Tank/Flg. Hdwr w/Gasket (#4)

1

Includes 8-5/8 x 3-1/4” hex head bolts, 8-5/8” nuts, 16-5/8” washers

10870-030

and 2 - 3” Neoprene FF Flg. Gaskets

1

5-2992

I

nstallation, Operation & Service Manual

1

6

” SINGLE FILTER KIT SCHEDULE 80

(14-7409)

I

tem Pentair Part# AP PN Size Description Sch. Qty

1

7 15-0081 10801-530 6 X 3 Socket Reducer Tee 80 2

19 15-0077 1827-030 3” Spig x Soc 45 Str. Elbow 80 2

20 15-3014 10463-528 6 X 2 Socket Reducer Saddle 40 3

21 15-2989 10851-020

2” Flg. One-Piece Socket - 150 lb.

80 1

2

2 15-0056 1

0856P-030 3” Flg. VS, Spigot - 150 lb. 80 2

23 15-0082 REQ.

3” Bolt Pack - Tank/Flg. Hdwr w/Gasket (#4)

1

Incl

udes 8-5/8 x 3-1/4” hex head bolts, 8-5/8” nuts, 16-5/8”washers

1

0870-030

a

nd 2 - 3” Neoprene FF Flg. Gaskets

15-2992

Installation, Operation & Service Manual

1

ADDENDUM TANDEM PLUMBING KIT PAGE 5

FILTER ADDER KIT

TWO FILTER

SYSTEM A B C D E F G H I J K TOTAL WT.

3” - TR100C 82 3/8” 17 15/16” 48” MIN. 18” MIN 39 3/4” 15” 29 33/64” 8 5/8” 11 31/32” 51 13/16” -------- 2300 LBS.

TR140C

-

3”

4” - TR140C 95 3/4” 19 35/64” 54” MIN. 18” MIN 45 1/2” 18” 33 1/8” 9 15/16” 12 21/32” 59 11/64” -------- 3300 LBS.

6” - TR140C 111 3/4” 24 7/32” 54” MIN. 18” MIN 45 1/2” 18” 35 3/8” 12 13/16” 10 21/64” 64 13/32” 69 53/64 3550 LBS.

88 3/8” 17 15/16” 54” MIN. 18” MIN 45 1/4” 18” 32 33/64” 8 5/8” 13 15/32” 57 13/16” -------- 3200 LBS.

6” PIPING NEEDS TO BE ROTATED UPWARD AS SHOWN AT 25° SO HANDLE WILL CLEAR THE FLOOR.

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

Use a plastic pipe sealant on the 2” valve

1

. Check carton for any evidence of damage due

to rough handling in Shipment. If carton or
any filter kit components are damaged, notify
freight carrier immediately.

adapter male thread and thread into the 2”
spigot female adapter making sure to have
the 3-1/2” plastic nut in place over the
adapter before doing so. If individual shut off
valves are desired, they can be placed in this

2. Refer to Filter Manual for details on filter
installation.

location. Dry fit the female adapter/valve
adapter assembly into the socket end of the 2”
spigot x socket 45° elbow. Dry fit spigot end of

TYPICAL SAND FILTER

FIGURE 4A

3. The Tandem filter kits have been designed to
provide the maximum flexibility for instal­lation. The installer will supply all the piping
to connect the complete system.

4. It is recommended that the filters be positi­oned in their final location and arranged to
allow sufficient service access for each filter
Equal filter spacing is recommended since it
simplifies the installation. Refer to filter tank
label for minimum filter clearance between fil
ters.

.

-

this assembly into the reduced tee port of the
reducer tee. These glue joints, which connects
the “T” to the 45° to the valve adapter, are
very important. Pre-assemble the joints dry
and insure that the “T” is aligned. Mark tim­ing marks on the female adapter, the 45°
elbow and the “T” to insure proper rea-lign­ment when making the final glue joint. Make
the final glue joint only after you are confi­dent that your alignment is proper.

3–inch Filter Unit “T” Assembly

You will need the following parts from your

5. Once filters are in position, place about 5 gal­lons of water in the tanks. This will help sta­bilize the filter.

6. It is best to cut all piping and dry assemble the
complete system prior to making any final
glue joints. This helps to insure that no mis­takes are made in the final system.

installation kit.

1. Socket Tee or Reducer Tee
(either 3 tee, 4x3 or 6x3 reducer tee)

2. 3” Spigot x Socket 45

° Street Elbow

3. 3” Flange, VS, Spigot

Dry fit the spigot end of the 3” Spigot x Socket
45° Street Elbow into the tee port of the stan­dard or reducer tee. Dry fit this assembly

assemblies first. These are the assemblies that
form the “T” connections that join directly to

You should assemble the tank “T” fitting

FIGURE 4B

the inlet and outlet of the filters – two assem­blies per tank. Follow the instructions for the
assemblies that correspond to the size filter
you are installing, either 2-inch or 3-inch.

2–inch Filter Unit “T” Assembly

You will need the following parts from your
installation kit.

Socket Reducer T

1.

ee

(either 3x2, 4x2 or 6x2)

2.

2” Spigot x Socket 45° Street Elbow

3. 2” Spigot Female Adapter,
Spigot x Female Pipe Thread

Adapter (P/N 271092)

alve

2” V

4.

READ AND FOLLOW ALL SAFETY INSTRUCTIONSREAD AND FOLLOW ALL SAFETY INSTRUCTIONS

onto the spigot nipple of the 3” spigot flange.
These glue joints, which connects the “T” to
the 45° to the flange, are very important. Pre­assemble the joints dry and insure that the
“T” is aligned. Mark timing marks on the
flange, the 45° elbow and the “T” to insure
proper rea-lignment when making the final
glue joint. Make the final glue joint only after
you are confident that your alignment is
proper.

Build up all of these “ T” fitting assemblies.
There should be two “T” assemblies for each
filter in your system. Let these assemblies
dry completely before continuing.

7. For the 2-inch filter units connect one “T”
assembly constructed above to each of the fil
ter bulkhead fittings with the 3-1/2” plastic
nut. For the 3-inch filter units connect the “T”

-

14

14

13

15

16

18

24

20

21

15

16

18

24

20

21

ADDENDUM TANDEM PLUMBING KIT PAGE 6

6

” SINGLE FILTER KIT SCHEDULE 40

(14-6408)

I

tem Pentair Part# AP PN Size Description Sch. Qty

5 15-0072 10401-528 6 X 2 Socket Reducer Tee 40 2

6

15-0060 10427-020 2” Spig x Soc 45 Str. Elbow 40 2

7 15-0061 10478-020

2” Spigot Female Adapter,Spig x Fipt

40 2

8 27-1092 27-1092

2”Valve Adapter Kit

1

11 15-3014 10463-528 6 X 2 Socket Reducer Saddle 40 3

12 15-2989 10851-020

2” Flg. One-Piece Socket - 150 lb.

80 1

15-2992

Installation, Operation & Service Manual

1

6” SINGLE FILTER KIT SCHEDULE 80

(14-6409)

Item Pentair Part# AP PN Size Description Sch. Qty

5 15-0074 10801-528 6 X 2 Socket Reducer Tee 80 2

6 15-0063 1827-020 2” Spig x Soc 45 Str. Elbow 80 2

7

15-0064 10878-020SR

2

” Spigot Female Adapter,Spig x Fipt802

8

27-1092 27-1092

2

”Valve Adapter Kit

1

11 15-3014 10463-528 6 X 2 Socket Reducer Saddle 40 3

12 15-2989 10851-020

2” Flg. One-Piece Socket - 150 lb.

80 1

15-2992

Installation, Operation & Service Manual

1

4” SINGLE FILTER KIT SCHEDULE 40

(14-6406)

Item Pentair Part# AP PN Size Description Sch. Qty

5 15-0068 10401-420 4 X 2 Socket Reducer Tee 40 2

6

15-0060 10427-020 2” Spig x Soc 45 Str. Elbow 40 2

7 15-0061 10478-020

2” Spigot Female Adapter,Spig x Fipt

40 2

8 27-1092 27-1092

2”Valve Adapter Kit

1

11 15-3010 10463-420 4 X 2 Socket Reducer Saddle 40 3

12 15-2989 10851-020

2” Flg. One-Piece Socket - 150 lb.

80 1

1

5-2992

I

nstallation, Operation & Service Manual

1

4” SINGLE FILTER KIT SCHEDULE 80

(14-6407)

Item Pentair Part# AP PN Size Description Sch. Qty

5 15-0069 10801-420 4 X 2 Socket Reducer Tee 80 2

6 15-0063 1827-020 2” Spig x Soc 45 Str. Elbow 80 2

7 15-0064 10878-020SR

2” Spigot Female Adapter,Spig x Fipt

80 2

8

27-1092 27-1092

2

”Valve Adapter Kit

1

11 15-3010 10463-420 4 X 2 Socket Reducer Saddle 40 3

12 15-2989 10851-020

2” Flg. One-Piece Socket - 150 lb.

80 1

15-2992

Installation, Operation & Service Manual

1

!

!

!

!

!

!

!

!

!

!

!

!

4” TWO FILTER KIT SCHEDULE 40

(

14-7402)

Item Pentair Part# AP PN Size Description Sch. Qty

13 15-3063 10854P-040 4 Flg. VS, Socket - 150lb. 80 2

14 15-0065 10856P-040 4 Flg. VS, Spigot - 150lb. 80 6

15 15-0066 1728-040 4 Butterfly Valve, Asahi SP 4

1

6 15-0067 REQ. 4

H

ardware Kit - Valve/Flg.Hardware (#2)

1

Includes 32-5/8 x 6” hex head bolts,32-5/8” nuts, 64-5/8” washers

17 15-0078 10401-422 4 X 3 Socket Reducer Tee 40 4

18 15-3012 10401-040 4 Socket Tee 40 1

19 15-0075 10427-030 3” Spig x Soc 45 Str. Elbow 40 4

20 15-3010 10463-420 4 X 2 Socket Reducer Saddle 40 3

2

1 15-2989 10851-020

2

” Flg. One-Piece Socket - 150 lb.Solid801

22 15-0056 10856P-030 3” Flg. VS,Spigot - 150 lb. 80 4

23 15-0076 REQ.

3” Bolt Pack - Tank/Flg. Hdwr w/Gasket (#4)

1

I

ncludes 16-5/8 x 3-1/4” hex head bolts,16-5/8” nuts, 32-5/8” washers

10870-030

and 4 - 3” Neoprene FF Flg. Gaskets

24 15-3007 10406-040 4 90 Socket Elbow

40 1

15-2992

Installation, Operation & Service Manual

1

6” TWO FILTER KIT SCHEDULE 40

(14-7404)

I

tem

Pentair Part# AP PN Size Description Sch. Qty

13 15-3064 10854P-060 6 Flg. VS, Socket - 150lb. 80 2

14

15-0070 10856P-060 6 Flg.VS, Spigot - 150lb. 80 6

15 15-0071 1728-060 6 Butterfly Valve, Asahi SP 4

16 15-0073 REQ. 6

Hardware Kit - Valve/Flg.Hardware (#2)

1

Includes 32-3/4” x 7”hex head bolts, 32-3/4” nuts, 64-3/4”washers

17 15-0080 10401-530 6 X 3 Socket Reducer Tee 40 4

18

15-3013 10401-060 6 Socket Tee 40 1

19

15-0075 10427-030 3” Spig x Soc 45 Str. Elbow 40 4

20

15-3014 10463-528 6 X 2 Socket Reducer Saddle 40 3

21 15-2989 10851-020

2” Flg. One-Piece Socket - 150 lb.Solid

80 1

22 15-0056 10856P-030 3” Flg. VS,Spigot - 150 lb. 80 4

23 15-0076 REQ.

3” Bolt Pack - Tank/Flg. Hdwr w/Gasket (#4)

1

Includes 16-5/8 x 3-1/4” hex head bolts,16-5/8” nuts, 32-5/8” washers

10870-030

and 4 - 3” Neoprene FF Flg. Gaskets

24 15-3008 10406-060 6 90 Socket Elbow

40 1

15-2992

Installation, Operation & Service Manual

1

4

” TWO FILTER KIT SCHEDULE 80

(14-7403)

I

tem Pentair Part# AP PN Size Description Sch. Qty

1315-3063 10854P-040 4 Flg.VS, Socket - 150lb. 80 2

14 15-0065 10856P-040 4 Flg. VS, Spigot - 150lb. 80 6

15

15-0066 1728-040 4 Butterfly Valve, Asahi SP 4

16 15-0067 REQ. 4

Hardware Kit - Valve/Flg.Hardware (#2)

1

Includes 32-5/8 x 6” hex head bolts,32-5/8” nuts, 64-5/8” washers

1

7 15-0079 10801-422 4 X 3 Socket Reducer Tee 80 4

1

8 15-3057 10801-040 4 Socket Tee 80 1

19 15-0077 10827-030 3” Spig x Soc 45 Str. Elbow 80 4

20 15-3010 10463-420 4 X 2 Socket Reducer Saddle 40 3

21 15-2989 10851-020

2” Flg. One-Piece Socket - 150 lb.Solid

80 1

2

2 15-0056 10856P-030 3” Flg. VS,Spigot - 150 lb. 80 4

23 15-0076 REQ.

3” Bolt Pack - Tank/Flg. Hdwr w/Gasket (#4)

1

Includes 16-5/8 x 3-1/4” hex head bolts,16-5/8” nuts, 32-5/8” washers

10870-030

and 4 - 3” Neoprene FF Flg. Gaskets

24 15-3066 10806-040 4 90 Socket Elbow

80 1

15-2992

Installation, Operation & Service Manual

1

6” TWO FILTER KIT SCHEDULE 80

(14-7405)

Item Pentair Part# AP PN Size Description Sch. Qty

1

3 15-3064 10854P-060 6 Flg. VS, Socket - 150lb. 80 2

14

1

5-0070 10856P-060 6 Flg.VS, Spigot - 150lb. 80 6

15 15-0071 1728-060 6 Butterfly Valve, Asahi SP 4

16

15-0073 REQ. 6

Hardware Kit - Valve/Flg.Hardware (#2)

1

Includes 32-3/4” x 7”hex head bolts, 32-3/4” nuts, 64-3/4”washers

17 15-0081 10801-530 6 X 3 Socket Reducer Tee 80 4

18 15-3059 10801-060 6 Socket Tee 80 1

19 15-0077 10827-030 3” Spig x Soc 45 Str. Elbow 80 4

20 15-3014 10463-528 6 X 2 Socket Reducer Saddle 40 3

21 15-2989 10851-020

2” Flg. One-Piece Socket - 150 lb.Solid

80 1

22 15-0056 10856P-030 3” Flg. VS,Spigot - 150 lb. 80 4

23 15-0076 REQ.

3” Bolt Pack - Tank/Flg. Hdwr w/Gasket (#4)

1

Includes 16-5/8 x 3-1/4” hex head bolts,16-5/8” nuts, 32-5/8” washers

10870-030

and 4 - 3” Neoprene FF Flg. Gaskets

24 15-3067 10406-060 6 90 Socket Elbow

80 1

15-2992

Installation, Operation & Service Manual

1

6” SINGLE FILTER KIT SCHEDULE 40

(14-6408)

Item Pentair Part# AP PN Size Description Sch. Qty

5 15-0072 10401-528 6 X 2 Socket Reducer Tee 40 2

6 15-0060 10427-020 2” Spig x Soc 45 Str.Elbow 40 2

7

15-0061 10478-020

2

” Spigot Female Adapter,Spig x Fipt402

8 27-1092 27-1092

2”Valve Adapter Kit

1

11 15-3014 10463-528 6 X 2 Socket Reducer Saddle 40 3

12 15-2989 10851-020

2” Flg. One-Piece Socket - 150 lb.

80 1

15-2992

Installation, Operation & Service Manual

1

6” SINGLE FILTER KIT SCHEDULE 80

(14-6409)

Item Pentair Part# AP PN Size Description Sch. Qty

5 15-0074 10801-528 6 X 2 Socket Reducer Tee 80 2

6 15-0063 1827-020 2” Spig x Soc 45 Str. Elbow 80 2

7 15-0064 10878-020SR

2” Spigot Female Adapter,Spig x Fipt

80 2

8

27-1092 27-1092

2

”Valve Adapter Kit

1

11 15-3014 10463-528 6 X 2 Socket Reducer Saddle 40 3

12 15-2989 10851-020

2” Flg. One-Piece Socket - 150 lb.

80 1

15-2992

Installation, Operation & Service Manual

1

!

!

!

!

!

!

4” TWO FILTER KIT SCHEDULE 80

(14-7403)

Item Pentair Part# AP PN Size Description Sch. Qty

13

15-3063 10854P-040 4 Flg.VS, Socket - 150lb. 80 2

14 15-0065 10856P-040 4 Flg. VS, Spigot - 150lb. 80 6

15

15-0066 1728-040 4 Butterfly Valve, Asahi SP 4

16 15-0067 REQ. 4

Hardware Kit - Valve/Flg.Hardware (#2)

1

Includes 32-5/8 x 6” hex head bolts,32-5/8” nuts, 64-5/8” washers

17 15-0079 10801-422 4 X 3 Socket Reducer Tee 80 4

18 15-3057 10801-040 4 Socket Tee 80 1

19 15-0077 10827-030 3” Spig x Soc 45 Str. Elbow 80 4

20 15-3010 10463-420 4 X 2 Socket Reducer Saddle 40 3

21 15-2989 10851-020

2” Flg. One-Piece Socket - 150 lb.Solid

80 1

22 15-0056 10856P-030 3” Flg. VS,Spigot - 150 lb. 80 4

23 15-0076 REQ.

3” Bolt Pack - Tank/Flg. Hdwr w/Gasket (#4)

1

Includes 16-5/8 x 3-1/4” hex head bolts,16-5/8” nuts, 32-5/8” washers

10870-030

and 4 - 3” Neoprene FF Flg. Gaskets

24 15-3066 10806-040 4 90 Socket Elbow

80 1

15-2992

Installation, Operation & Service Manual

1

6” TWO FILTER KIT SCHEDULE 80

(14-7405)

Item Pentair Part# AP PN Size Description Sch. Qty

13 15-3064 10854P-060 6 Flg. VS, Socket - 150lb. 80 2

14

15-0070 10856P-060 6 Flg.VS, Spigot - 150lb. 80 6

15 15-0071 1728-060 6 Butterfly Valve, Asahi SP 4

16

15-0073 REQ. 6

Hardware Kit - Valve/Flg.Hardware (#2)

1

Includes 32-3/4” x 7”hex head bolts, 32-3/4” nuts, 64-3/4”washers

17 15-0081 10801-530 6 X 3 Socket Reducer Tee 80 4

18 15-3059 10801-060 6 Socket Tee 80 1

19 15-0077 10827-030 3” Spig x Soc 45 Str. Elbow 80 4

20 15-3014 10463-528 6 X 2 Socket Reducer Saddle 40 3

21 15-2989 10851-020

2” Flg. One-Piece Socket - 150 lb.Solid

80 1

22 15-0056 10856P-030 3” Flg. VS,Spigot - 150 lb. 80 4

23 15-0076 REQ.

3” Bolt Pack - Tank/Flg. Hdwr w/Gasket (#4)

1

Includes 16-5/8 x 3-1/4” hex head bolts,16-5/8” nuts, 32-5/8” washers

10870-030

and 4 - 3” Neoprene FF Flg. Gaskets

24 15-3067 10406-060 6 90 Socket Elbow

80 1

15-2992

Installation, Operation & Service Manual

1

6” SINGLE FILTER KIT SCHEDULE 40

(14-6408)

Item Pentair Part# AP PN Size Description Sch. Qty

5 15-0072 10401-528 6 X 2 Socket Reducer Tee 40 2

6 15-0060 10427-020 2” Spig x Soc 45 Str.Elbow 40 2

7 15-0061 10478-020

2” Spigot Female Adapter,Spig x Fipt

40 2

8 27-1092 27-1092

2”Valve Adapter Kit

1

11 15-3014 10463-528 6 X 2 Socket Reducer Saddle 40 3

12 15-2989 10851-020

2” Flg. One-Piece Socket - 150 lb.

80 1

15-2992

Installation, Operation & Service Manual

1

6” SINGLE FILTER KIT SCHEDULE 80

(14-6409)

Item Pentair Part# AP PN Size Description Sch. Qty

5 15-0074 10801-528 6 X 2 Socket Reducer Tee 80 2

6 15-0063 1827-020 2” Spig x Soc 45 Str. Elbow 80 2

7 15-0064 10878-020SR

2” Spigot Female Adapter,Spig x Fipt

80 2

8 27-1092 27-1092

2”Valve Adapter Kit

1

11 15-3014 10463-528 6 X 2 Socket Reducer Saddle 40 3

12 15-2989 10851-020

2” Flg. One-Piece Socket - 150 lb.

80 1

15-2992

Installation, Operation & Service Manual

1

!

!

!

!

4” TWO FILTER KIT SCHEDULE 80

(14-7403)

Item Pentair Part# AP PN Size Description Sch. Qty

13 15-3063 10854P-040 4 Flg. VS, Socket - 150lb. 80 2

14 15-0065 10856P-040 4 Flg. VS, Spigot - 150lb. 80 6

15

15-0066 1728-040 4 Butterfly Valve, Asahi SP 4

16 15-0067 REQ. 4

Hardware Kit - Valve/Flg.Hardware (#2)

1

Includes 32-5/8 x 6” hex head bolts,32-5/8” nuts, 64-5/8” washers

17 15-0079 10801-422 4 X 3 Socket Reducer Tee 80 4

18 15-3057 10801-040 4 Socket Tee 80 1

19 15-0077 10827-030 3” Spig x Soc 45 Str. Elbow 80 4

20 15-3010 10463-420 4 X 2 Socket Reducer Saddle 40 3

21 15-2989 10851-020

2” Flg. One-Piece Socket - 150 lb.Solid

80 1

22 15-0056 10856P-030 3” Flg. VS,Spigot - 150 lb. 80 4

23 15-0076 REQ.

3” Bolt Pack - Tank/Flg. Hdwr w/Gasket (#4)

1

Includes 16-5/8 x 3-1/4” hex head bolts,16-5/8” nuts, 32-5/8” washers

10870-030

and 4 - 3” Neoprene FF Flg. Gaskets

24 15-3066 10806-040 4 90 Socket Elbow

80 1

15-2992

Installation, Operation & Service Manual

1

!

!

!

!

VALVED FILTER MANIFOLD

3” TWO FILTER KIT SCHEDULE 40

(14-7400)

Item Pentair Part# AP PN Size Description Sch. Qty

13 15-3062 10854P-030 3 Flg. VS, Socket - 150lb. 80 2

14 15-0056 10856P-030 3 Flg. VS, Spigot - 150lb. 80 6

1

5 15-0057 1728-030 3 Butterfly Valve, Asahi SP 4

1

6 15-0058 REQ. 3

H

ardware Kit - Valve/Flg.Hardware (#1)

1

Includes 16-5/8 x 6” hex head bolts,16-5/8” nuts, 32-5/8” washers

17 15-3011 10401-030 3 Socket Tee 40 5

19 15-0075 10427-030 3” Spig x Soc 45 Str. Elbow 40 4

2

0 15-3009 10463-338 3 X 2 Socket Reducer Saddle 40 3

21 15-2989 10851-020

2” Flg. One-Piece Socket - 150lb Solid

80 1

2

2 15-0056 10856P-030 3” Flg. VS.Spigot - 150lb 80 4

23 15-0076 REQ.

3” Bolt Pack - Tank/Flg. Hdwr w/Gasket (#4)

1

Includes 16-5/8 x 6” hex head bolts,16-5/8” nuts, 32-5/8” washers

10470-030

and 4 - 3” Neoprene FF Flg. Gaskets

24 15-3006 10406-030 3 90 Socket Elbow 80 1

15-2992

Installation, Operation & Service Manual

1

VALVED FILTER MANIFOLD

3” TWO FILTER KIT SCHEDULE 80

(14-7401)

Item Pentair Part# AP PN Size Description Sch. Qty

13 15-3062 10854P-030 3 Flg. VS, Socket - 150lb. 80 2

14 15-0056 10856P-030 3 Flg. VS, Spigot - 150lb. 80 6

15 15-0057 1728-030 3 Butterfly Valve, Asahi SP 4

1

6 15-0058 REQ. 3

H

ardware Kit - Valve/Flg.Hardware (#1)

1

Includes 16-5/8 x 6” hex head bolts,16-5/8” nuts, 32-5/8” washers

17 15-3056 10801-030 3 Socket Tee 80 5

19 15-0077 10827-030 3” Spig x Soc 45 Str. Elbow 80 4

20 15-3009 10463-338 3 X 2 Socket Reducer Saddle 40 3

21 15-2989 10851-020

2” Flg. One-Piece Socket - 150lb Solid

80 1

22 15-0056 10856P-030 3” Flg. VS.Spigot - 150lb 80 4

23 15-0076 REQ.

3” Bolt Pack - Tank/Flg. Hdwr w/Gasket (#4)

1

Inc

ludes 16-5/8 x 6” hex head bolts,16-5/8” nuts, 32-5/8” washers

10870-030

and 4 - 3” Neoprene FF Flg. Gaskets

24

15-3065 10806-030 3 90 Socket Elbow 80 1

15-2992

Installation, Operation & Service Manual

1

!

!

VALVED FILTER MANIFOLD

3” TWO FILTER KIT SCHEDULE 40

(14-7400)

I

tem Pentair Part# AP PN Size Description Sch. Qty

13 15-3062 10854P-030 3 Flg. VS, Socket - 150lb. 80 2

14 15-0056 10856P-030 3 Flg. VS, Spigot - 150lb. 80 6

15 15-0057 1728-030 3 Butterfly Valve, Asahi SP 4

16 15-0058 REQ. 3

Hardware Kit - Valve/Flg.Hardware (#1)

1

Includes 16-5/8 x 6” hex head bolts,16-5/8” nuts, 32-5/8” washers

1

7 15-3011 10401-030 3 Socket Tee 40 5

1

9 15-0075 10427-030 3” Spig x Soc 45 Str. Elbow 40 4

20 15-3009 10463-338 3 X 2 Socket Reducer Saddle 40 3

21 15-2989 10851-020

2” Flg. One-Piece Socket - 150lb Solid

80 1

22 15-0056 10856P-030 3” Flg. VS.Spigot - 150lb 80 4

23 15-0076 REQ.

3” Bolt Pack - Tank/Flg. Hdwr w/Gasket (#4)

1

I

ncludes 16-5/8 x 6” hex head bolts,16-5/8” nuts, 32-5/8” washers

10470-030

and 4 - 3” Neoprene FF Flg. Gaskets

24 15-3006 10406-030 3 90 Socket Elbow 80 1

15-2992

Installation, Operation & Service Manual

1

6” SINGLE FILTER KIT SCHEDULE 40

(

14-6408)

Item Pentair Part# AP PN Size Description Sch. Qty

5 15-0072 10401-528 6 X 2 Socket Reducer Tee 40 2

6 15-0060 10427-020 2” Spig x Soc 45 Str.Elbow 40 2

7 15-0061 10478-020

2” Spigot Female Adapter,Spig x Fipt

40 2

8 27-1092 27-1092

2”Valve Adapter Kit

1

11 15-3014 10463-528 6 X 2 Socket Reducer Saddle 40 3

12 15-2989 10851-020

2” Flg. One-Piece Socket - 150 lb.

80 1

15-2992

Installation, Operation & Service Manual

1

6” SINGLE FILTER KIT SCHEDULE 80

(14-6409)

I

tem Pentair Part# AP PN Size Description Sch. Qty

5

15-0074 10801-528 6 X 2 Socket Reducer Tee 80 2

6 15-0063 1827-020 2” Spig x Soc 45 Str. Elbow 80 2

7 15-0064 10878-020SR

2” Spigot Female Adapter,Spig x Fipt

80 2

8 27-1092 27-1092

2”Valve Adapter Kit

1

1

1 15-3014 10463-528 6 X 2 Socket Reducer Saddle 40 3

12 15-2989 10851-020

2” Flg. One-Piece Socket - 150 lb.

80 1

15-2992

Installation, Operation & Service Manual

1

4

” SINGLE FILTER KIT SCHEDULE 40

(14-6406)

I

tem Pentair Part# AP PN Size Description Sch. Qty

5 15-0068 10401-420 4 X 2 Socket Reducer Tee 40 2

6 15-0060 10427-020 2” Spig x Soc 45 Str.Elbow 40 2

7 15-0061 10478-020

2” Spigot Female Adapter,Spig x Fipt

40 2

8 27-1092 27-1092

2”Valve Adapter Kit

1

11 15-3010 10463-420 4 X 2 Socket Reducer Saddle 40 3

12 15-2989 10851-020

2” Flg. One-Piece Socket - 150 lb.

80 1

15-2992

Installation, Operation & Service Manual

1

4” SINGLE FILTER KIT SCHEDULE 80

(14-6407)

Item Pentair Part# AP PN Size Description Sch. Qty

5 15-0069 10801-420 4 X 2 Socket Reducer Tee 80 2

6 15-0063 1827-020 2” Spig x Soc 45 Str. Elbow 80 2

7 15-0064 10878-020SR

2” Spigot Female Adapter,Spig x Fipt

80 2

8 27-1092 27-1092

2”Valve Adapter Kit

1

11 15-3010 10463-420 4 X 2 Socket Reducer Saddle 40 3

12 15-2989 10851-020

2” Flg. One-Piece Socket - 150 lb.

80 1

15-2992

Installation, Operation & Service Manual

1

!

!

!

!

!

!

!

!

4” TWO FILTER KIT SCHEDULE 40

(14-7402)

I

tem Pentair Part# AP PN Size Description Sch. Qty

13 15-3063 10854P-040 4 Flg. VS, Socket - 150lb. 80 2

14 15-0065 10856P-040 4 Flg. VS, Spigot - 150lb. 80 6

15 15-0066 1728-040 4 Butterfly Valve, Asahi SP 4

16 15-0067 REQ. 4

Hardware Kit - Valve/Flg.Hardware (#2)

1

Includes 32-5/8 x 6” hex head bolts,32-5/8” nuts, 64-5/8” washers

17 15-0078 10401-422 4 X 3 Socket Reducer Tee 40 4

18 15-3012 10401-040 4 Socket Tee 40 1

19 15-0075 10427-030 3” Spig x Soc 45 Str. Elbow 40 4

20 15-3010 10463-420 4 X 2 Socket Reducer Saddle 40 3

21 15-2989 10851-020

2” Flg. One-Piece Socket - 150 lb.Solid

80 1

22 15-0056 10856P-030 3” Flg. VS,Spigot - 150 lb. 80 4

23 15-0076 REQ.

3” Bolt Pack - Tank/Flg. Hdwr w/Gasket (#4)

1

Includes 16-5/8 x 3-1/4” hex head bolts,16-5/8” nuts, 32-5/8” washers

10870-030

and 4 - 3” Neoprene FF Flg. Gaskets

24 15-3007 10406-040 4 90 Socket Elbow

40 1

15-2992

Installation, Operation & Service Manual

1

4” TWO FILTER KIT SCHEDULE 80

(14-7403)

Item Pentair Part# AP PN Size Description Sch. Qty

13

15-3063 10854P-040 4 Flg.VS, Socket - 150lb. 80 2

14 15-0065 10856P-040 4 Flg. VS, Spigot - 150lb. 80 6

15

15-0066 1728-040 4 Butterfly Valve, Asahi SP 4

16 15-0067 REQ. 4

Hardware Kit - Valve/Flg.Hardware (#2)

1

Includes 32-5/8 x 6” hex head bolts,32-5/8” nuts, 64-5/8” washers

17 15-0079 10801-422 4 X 3 Socket Reducer Tee 80 4

18 15-3057 10801-040 4 Socket Tee 80 1

19 15-0077 10827-030 3” Spig x Soc 45 Str. Elbow 80 4

20 15-3010 10463-420 4 X 2 Socket Reducer Saddle 40 3

21 15-2989 10851-020

2” Flg. One-Piece Socket - 150 lb.Solid

80 1

22 15-0056 10856P-030 3” Flg. VS,Spigot - 150 lb. 80 4

23 15-0076 REQ.

3” Bolt Pack - Tank/Flg. Hdwr w/Gasket (#4)

1

Includes 16-5/8 x 3-1/4” hex head bolts,16-5/8” nuts, 32-5/8” washers

10870-030

and 4 - 3” Neoprene FF Flg. Gaskets

24 15-3066 10806-040 4 90 Socket Elbow

80 1

assembly to the inlet and outlet flanges with
t

he 3” Bolt Pack w/gasket from the installation
kit. You may need to use temporary supports
under the “T” assemblies while making these
connections.

8. Inter connecting pipes between “T”’s can now
be added. Insure that the filters are in posi­tion and in a straight line and equal distance
apart. Measure and cut “T” connector pipes for
both top and bottom “T”’s. These connector
pipes should all be the same length unless a
set of filters is unequally spaced. Do not make
final glue joint until pipe supports are in place.
See step 9.

9. Dry assemble the connecting pipes between
filter “T”’s and place the saddle supports into
position to measure for the support legs. One
set of supports goes between the manifold
pipes and directly under that support is the
other support with flanged bottom. Measure
both support legs and cut appropriate 2” pipes
to fit. Dry assemble and mark timing marks

10. The connecting pipes between filter “T”’s may

1.

1

on all joints so that they may be re-assembled
properly when the final glue joints are made.
Repeat for the second set of supports. Make
the final glue joints only after you are confi­dent that your piping is correct.

now be glued. Make the final glue joint only
after you are confident that your piping is cor­rect.

The end filters on both the inlet side of the sys
tem and the return side of the system may
now be flanged and valves installed. The kits
are supplied with two different types of
flanges: socket and spigot flanges. The flanges
in the kit should arrive assembled but in ship
ping might have become disassembled. If so,
install the flanges over the spigot/socket stub
ends. Pre-assemble all 8 flange/ stub end
assemblies. The flange has a recess on the ID,
which allows two small protrusions on the
stub end to slip thru the flange and the pro
trusion locks the flange and stub end together
when rotated slightly. Use the spigot type
flanges to connect to the open end of the four
“T”’s on the filter units. The spigot stub ends

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

TANDEM SYSTEM PLUMBING KIT PAGE 11

will glue directly into the open ends of the
“T”’s. Make the final glue joints between the
“T”’s and flange/stub end assemblies, only
when you are confident that your piping is
correct.

12. The four valves and flange/stub end assem­blies can now be mounted. NOTE: use the
remaining two spigot end flanges on the inlet
side of the filter units and use the two socket
end flanges on the outlet side. This will allow
the tee and elbow inlet fittings to be cement­ed directly to the spigot flanges and leave the
socket flanges for the outlet pipe.

It is helpful to have two people to mount the
valves. Locate the Hardware Kit – Valve/Flg.
Hdwr. and pull 4 or 8 bolts, nuts and washer
sets for use in mounting valves. A 3-inch
valve will require 4 sets; the 4 and 6 inch will
require 8 sets. Place 2 bolts and washers
thru the mounted flange 180° apart. Place the
valves into position as indicated on Figure 3
B in the installation manual. Be certain that
the teeth of the latch-ing mechanism are ori
ented as depicted in Figure 3 B. Place the
mating flange on the assembly and use wash­er and nuts on two bolts to snug the flanges
and valve together. Do this on all four
valves/flange combinations.

13. The final tee and elbow inlet fittings may now
be assembled. Place the tee on the top mani-

-

fold spigot flange nipple and the elbow on the

-

-

-

bottom manifold spigot flange nipple. Snug
them in place and measure the length of the
connecting pipe. Field cut the pipe and dry
assemble. Once you are certain of your
assembly

, mark the tee, elbow and connec-tor
pipe to insure proper re-assembly. Glue all
four joints.

14. Install all remaining flange bolts with washers
and nuts. Follow the recommended bolt
torque and tightening sequence when making
the final installation of the bolt, nut and
washer sets.

15. The manifold is now complete and remaining
piping can now be connected.

E. PARTS LIST FOR TR 100C3 & 140C3 FILTERS

INLET MANIFOLD

3” INLET MANIFOLD

(SCH 40, SCH 80)

ITEM PART # PART # DESCRIPTION QTY

SCH 40 SCH 80

5 15-3011 15-3056 3” SXSXS TEE 1

11 15-3006 15-3065 3” -90 ELL SXS 1

4” INLET MANIFOLD

(SCH 40, SCH 80)

ITEM PART # PART # DESCRIPTION QTY

CH 40 SCH 80

S

15-3012 15-3057 4” SXSXS TEE 1

5

2 15-3007 15-3066 4” -90 ELL SXS 1

1

ITEM PART # PART # DESCRIPTION QTY

6 15-3013 15-3059 6” SXSXS TEE 1

2 15-3008 15-3067 6” -90 ELL SXS 1

1

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

6” INLET MANIFOLD

CH 40 SCH 80

S

90 ELL

(SCH 40, SCH 80)

o

SOCKET TEE

TANDEM SYSTEM PLUMBING KIT PAGE 10

6” SINGLE FILTER KIT SCHEDULE 40

(14-6408)

Item Pentair Part# AP PN Size Description Sch. Qty

5

15-0072 10401-528 6 X 2 Socket Reducer Tee 40 2

6 15-0060 10427-020 2” Spig x Soc 45 Str. Elbow 40 2

7 15-0061 10478-020

2” Spigot Female Adapter,Spig x Fipt

40 2

8

27-1092 27-1092

2

”Valve Adapter Kit

1

11 15-3014 10463-528 6 X 2 Socket Reducer Saddle 40 3

12 15-2989 10851-020

2” Flg. One-Piece Socket - 150 lb.

80 1

1

5-2992

I

nstallation, Operation & Service Manual

1

6” SINGLE FILTER KIT SCHEDULE 80

(

14-6409)

Item Pentair Part# AP PN Size Description Sch. Qty

5

15-0074 10801-528 6 X 2 Socket Reducer Tee 80 2

6 15-0063 1827-020 2” Spig x Soc 45 Str. Elbow 80 2

7 15-0064 10878-020SR

2” Spigot Female Adapter,Spig x Fipt

80 2

8

27-1092 27-1092

2

”Valve Adapter Kit

1

1

1 15-3014 10463-528 6 X 2 Socket Reducer Saddle 40 3

12 15-2989 10851-020

2” Flg. One-Piece Socket - 150 lb.

80 1

15-2992

Installation, Operation & Service Manual

1

4

” SINGLE FILTER KIT SCHEDULE 40

(14-6406)

Item Pentair Part# AP PN Size Description Sch. Qty

5 15-0068 10401-420 4 X 2 Socket Reducer Tee 40 2

6 15-0060 10427-020 2” Spig x Soc 45 Str. Elbow 40 2

7

15-0061 10478-020

2

” Spigot Female Adapter,Spig x Fipt402

8

27-1092 27-1092

2

”Valve Adapter Kit

1

1

1 15-3010 10463-420 4 X 2 Socket Reducer Saddle 40 3

1

2 15-2989 10851-020

2

” Flg. One-Piece Socket - 150 lb.801

15-2992

Installation, Operation & Service Manual

1

4” SINGLE FILTER KIT SCHEDULE 80

(14-6407)

I

tem Pentair Part# AP PN Size Description Sch. Qty

5

15-0069 10801-420 4 X 2 Socket Reducer Tee 80 2

6

15-0063 1827-020 2” Spig x Soc 45 Str.Elbow 80 2

7

15-0064 10878-020SR

2

” Spigot Female Adapter,Spig x Fipt802

8 27-1092 27-1092

2”Valve Adapter Kit

1

11 15-3010 10463-420 4 X 2 Socket Reducer Saddle 40 3

1

2 15-2989 10851-020

2

” Flg. One-Piece Socket - 150 lb.801

1

5-2992

I

nstallation, Operation & Service Manual

1

!

!

!

!

6” SINGLE FILTER KIT SCHEDULE 40

(

14-6408)

Item Pentair Part# AP PN Size Description Sch. Qty

5 15-0072 10401-528 6 X 2 Socket Reducer Tee 40 2

6

15-0060 10427-020 2” Spig x Soc 45 Str. Elbow 40 2

7

15-0061 10478-020

2

” Spigot Female Adapter,Spig x Fipt402

8 27-1092 27-1092

2”Valve Adapter Kit

1

1

1 15-3014 10463-528 6 X 2 Socket Reducer Saddle 40 3

12 15-2989 10851-020

2” Flg. One-Piece Socket - 150 lb.

80 1

1

5-2992

I

nstallation, Operation & Service Manual

1

6” SINGLE FILTER KIT SCHEDULE 80

(14-6409)

Item Pentair Part# AP PN Size Description Sch. Qty

5

15-0074 10801-528 6 X 2 Socket Reducer Tee 80 2

6 15-0063 1827-020 2” Spig x Soc 45 Str. Elbow 80 2

7 15-0064 10878-020SR

2” Spigot Female Adapter,Spig x Fipt

80 2

8

27-1092 27-1092

2

”Valve Adapter Kit

1

1

1 15-3014 10463-528 6 X 2 Socket Reducer Saddle 40 3

12 15-2989 10851-020

2” Flg. One-Piece Socket - 150 lb.

80 1

15-2992

Installation, Operation & Service Manual

1

!

!

FILTER ADDER KIT

TANDEM SYSTEM PLUMBING KIT PAGE 7

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

TANDEM SYSTEM PLUMBING KIT PAGE 8

!

!

3” TWO FILTER KIT SCHEDULE 40

(14-6400)

Item Pentair Part# AP PN Size Description Sch. Qty

1 15-3062 10854P-030 3 Flg.VS, Socket - 150lb. 80 2

2 15-0056 10856P-030 3 Flg.VS, Spigot - 150lb. 80 6

3 15-0057 1728-030 3 Butterfly Valve, Asahi SP 4

4

15-0058 REQ. 3

H

ardware Kit - Valve/Flg.Hardware (#1)

1

Includes 16-5/8 x 6” hex head bolts,16-5/8” nuts, 32-5/8” washers

5 15-0059 10401-338 3 X 2 Socket Reducer Tee 40 4

6 15-0060 10427-020 2”Spig x Soc 45 Str. Elbow 40 4

7 15-0061 10478-020

2” Spigot Female Adapter,Spig x Fipt

40 4

8

27-1092 27-1092

2

”Valve Adapter Kit

2

9 15-3011 10401-030 3 Socket Tee 40 1

10

15-3006 10406-030 3 90 Socket Elbow 40 1

11 15-3009 10463-338 3 X 2 Socket Reducer Saddle 40 6

12 15-2989 10851-020

2” Flg. One-Piece Socket - 150 lb. 80 2

15-2992

Installation, Operation & Service Manual

1

6” TWO FILTER KIT SCHEDULE 80

(14-6405)

Item Pentair Part# AP PN Size Description Sch. Qty

1 15-3064 10854P-060 6 Flg.VS, Socket - 150lb. 80 2

2

15-0070 10856P-060 6 Flg.VS, Spigot - 150lb. 80 6

3 15-0071 1728-060 6 Butterfly Valve, Asahi SP 4

4

15-0073 REQ. 6

H

ardware Kit - Valve/Flg.Hardware (#1)

1

Includes 32-3/4 x 7” hex head bolts,32-3/4” nuts, 64-3/4” washers

5

15-0074 10801-528 6 X 2 Socket Reducer Tee 80 4

6 15-0063 10827-020 2”Spig x Soc 45 Str. Elbow 80 4

7

15-0064 10878-020SR

2” Spigot Female Adapter,Spig x Fipt

80 4

8 27-1092 27-1092

2”Valve Adapter Kit

2

9

15-3059 10801-060 6 Socket Tee 80 1

10

15-3067 10806-060 6 90 Socket Elbow 80 1

1

1 15-3014 10463-528 6 X 2 Socket Reducer Saddle 40 6

12 15-2989 10851-020

2” Flg. One-Piece Socket - 150 lb. 80 2

15-2992

Installation, Operation & Service Manual

1

6”

TWO FILTER KIT SCHEDULE 40

(14-6404)

Item Pentair Part# AP PN Size Description Sch. Qty

1 15-3064 10854P-060 6 Flg.VS, Socket - 150lb. 80 2

2 15-0070 10856P-060 6 Flg.VS, Spigot - 150lb. 80 6

3 15-0071 1728-060 6 Butterfly Valve, Asahi SP 4

4 15-0073 REQ . 6

Hardware Kit - Valve/Flg.Hardware (#1)

1

Inc

ludes 32-3/4 x 7” hex head bolts,32-3/4” nuts, 64-3/4” washers

5 15-0072 10401-528 6 X 2 Socket Reducer Tee 40 4

6 15-0060 10427-020 2”Spig x Soc 45 Str. Elbow 40 4

7 15-0061 10478-020

2” Spigot Female Adapter,Spig x Fipt

40 4

8 27-1092 27-1092

2”Valve Adapter Kit

2

9 15-3013 10401-060 6 Socket Tee 40 1

10

1

5-3008 10406-060 6 90 Socket Elbow 40 1

11

15-3014 10463-528 6 X 2 Socket Reducer Saddle 40 6

12

15-2989 10851-020

2” Flg. One-Piece Socket - 150 lb. 80 2

15-2992

Installation, Operation & Service Manual

1

3” TWO FILTER KIT SCHEDULE 80

(

14-6401)

Item Pentair Part# AP PN Size Description Sch. Qty

1 15-3062 10854P-030 3 Flg.VS, Socket - 150lb. 80 2

2

15-0056 10856P-030 3 Flg.VS, Spigot - 150lb. 80 6

3 15-0057 1728-030 3 Butterfly Valve, Asahi SP 4

4

15-0058 REQ. 3

H

ardware Kit - Valve/Flg.Hardware (#1)

1

Includes 16-5/8 x 6” hex head bolts,16-5/8” nuts, 32-5/8” washers

5 15-0062 10801-338 3 X 2 Socket Reducer Tee 80 4

6 15-0063 10827-020 2”Spig x Soc 45 Str. Elbow 80 4

7 15-0064 10878-020SR

2” Spigot Female Adapter,Spig x Fipt

80 4

8 27-1092 27-1092

2”Valve Adapter Kit

2

9 15-3056 10801-030 3 Socket Tee 80 1

10

1

5-3065 10806-030 3 90 Socket Elbow 80 1

11 15-3009 10463-338 3 X 2 Socket Reducer Saddle 40 6

12 15-2989 10851-020

2” Flg. One-Piece Socket - 150 lb. 80 2

15-2992

Installation, Operation & Service Manual

1

!

!

!

!

!

!

!

!

!

!

VALVED FILTER MANIFOLD

3

” TWO FILTER KIT SCHEDULE 40

(

14-7400)

Item Pentair Part# AP PN Size Description Sch. Qty

13 15-3062 10854P-030 3 Flg. VS, Socket - 150lb. 80 2

14 15-0056 10856P-030 3 Flg. VS, Spigot - 150lb. 80 6

1

5 15-0057 1728-030 3 Butterfly Valve, Asahi SP 4

16 15-0058 REQ. 3

Hardware Kit - Valve/Flg.Hardware (#1)

1

Includes 16-5/8 x 6” hex head bolts,16-5/8” nuts, 32-5/8” washers

17 15-3011 10401-030 3 Socket Tee 40 5

19 15-0075 10427-030 3” Spig x Soc 45 Str. Elbow 40 4

20 15-3009 10463-338 3 X 2 Socket Reducer Saddle 40 3

21 15-2989 10851-020

2” Flg. One-Piece Socket - 150lb Solid

80 1

22 15-0056 10856P-030 3” Flg. VS.Spigot - 150lb 80 4

23 15-0076 REQ.

3” Bolt Pack - Tank/Flg. Hdwr w/Gasket (#4)

1

Includes 16-5/8 x 6” hex head bolts,16-5/8” nuts, 32-5/8” washers

10470-030

and 4 - 3” Neoprene FF Flg. Gaskets

2

4 15-3006 10406-030 3 90 Socket Elbow 80 1

15-2992

Installation, Operation & Service Manual

1

V

ALVED FILTER MANIFOLD

3

” TWO FILTER KIT SCHEDULE 80

(14-7401)

Item Pentair Part# AP PN Size Description Sch. Qty

13 15-3062 10854P-030 3 Flg. VS, Socket - 150lb. 80 2

14 15-0056 10856P-030 3 Flg. VS, Spigot - 150lb. 80 6

15 15-0057 1728-030 3 Butterfly Valve, Asahi SP 4

16 15-0058 REQ. 3

Hardware Kit - Valve/Flg.Hardware (#1)

1

Includes 16-5/8 x 6” hex head bolts,16-5/8” nuts, 32-5/8” washers

17 15-3056 10801-030 3 Socket Tee 80 5

1

9 15-0077 10827-030 3” Spig x Soc 45 Str. Elbow 80 4

20 15-3009 10463-338 3 X 2 Socket Reducer Saddle 40 3

21 15-2989 10851-020

2” Flg. One-Piece Socket - 150lb Solid

80 1

22 15-0056 10856P-030 3” Flg. VS.Spigot - 150lb 80 4

23 15-0076 REQ.

3” Bolt Pack - Tank/Flg. Hdwr w/Gasket (#4)

1

I

ncludes 16-5/8 x 6” hex head bolts,16-5/8” nuts, 32-5/8” washers

10870-030

and 4 - 3” Neoprene FF Flg. Gaskets

24 15-3065 10806-030 3 90 Socket Elbow 80 1

15-2992

Installation, Operation & Service Manual

1

!

!

3” TWO FILTER KIT SCHEDULE 40

(14-6400)

Item Pentair Part# AP PN Size Description Sch. Qty

1 15-3062 10854P-030 3 Flg.VS, Socket - 150lb. 80 2

2 15-0056 10856P-030 3 Flg.VS, Spigot - 150lb. 80 6

3 15-0057 1728-030 3 Butterfly Valve, Asahi SP 4

4 15-0058 REQ . 3

Hardware Kit - Valve/Flg.Hardware (#1)

1

I

ncludes 16-5/8 x 6” hex head bolts,16-5/8” nuts, 32-5/8” washers

5 15-0059 10401-338 3 X 2 Socket Reducer Tee 40 4

6 15-0060 10427-020 2”Spig x Soc 45 Str. Elbow 40 4

7 15-0061 10478-020

2” Spigot Female Adapter,Spig x Fipt

40 4

8 27-1092 27-1092

2”Valve Adapter Kit

2

9 15-3011 10401-030 3 Socket Tee 40 1

10

15-3006 10406-030 3 90 Socket Elbow 40 1

11 15-3009 10463-338 3 X 2 Socket Reducer Saddle 40 6

12 15-2989 10851-020

2” Flg. One-Piece Socket - 150 lb. 80 2

1

5-2992

I

nstallation, Operation & Service Manual

1

6” TWO FILTER KIT SCHEDULE 80

(14-6405)

Item Pentair Part# AP PN Size Description Sch. Qty

1 15-3064 10854P-060 6 Flg.VS, Socket - 150lb. 80 2

2 15-0070 10856P-060 6 Flg.VS, Spigot - 150lb. 80 6

3 15-0071 1728-060 6 Butterfly Valve, Asahi SP 4

4

15-0073 REQ. 6

H

ardware Kit - Valve/Flg.Hardware (#1)

1

Includes 32-3/4 x 7” hex head bolts,32-3/4” nuts, 64-3/4” washers

5

15-0074 10801-528 6 X 2 Socket Reducer Tee 80 4

6

15-0063 10827-020 2” Spig x Soc 45 Str. Elbow 80 4

7

15-0064 10878-020SR

2” Spigot Female Adapter,Spig x Fipt

80 4

8 27-1092 27-1092

2”Valve Adapter Kit

2

9 15-3059 10801-060 6 Socket Tee 80 1

101

5-3067 10806-060 6 90 Socket Elbow 80 1

1

1 15-3014 10463-528 6 X 2 Socket Reducer Saddle 40 6

12 15-2989 10851-020

2” Flg. One-Piece Socket - 150 lb. 80 2

15-2992

Installation, Operation & Service Manual

1

6”

TWO FILTER KIT SCHEDULE 40

(14-6404)

Item Pentair Part# AP PN Size Description Sch. Qty

1 15-3064 10854P-060 6 Flg.VS, Socket - 150lb. 80 2

2 15-0070 10856P-060 6 Flg.VS, Spigot - 150lb. 80 6

3

15-0071 1728-060 6 Butterfly Valve, Asahi SP 4

4 15-0073 REQ . 6

Hardware Kit - Valve/Flg.Hardware (#1)

1

Inc

ludes 32-3/4 x 7” hex head bolts,32-3/4” nuts, 64-3/4” washers

5 15-0072 10401-528 6 X 2 Socket Reducer Tee 40 4

6 15-0060 10427-020 2”Spig x Soc 45 Str. Elbow 40 4

7 15-0061 10478-020

2” Spigot Female Adapter,Spig x Fipt

40 4

8 27-1092 27-1092

2”Valve Adapter Kit

2

9 15-3013 10401-060 6 Socket Tee 40 1

10

1

5-3008 10406-060 6 90 Socket Elbow 40 1

11

15-3014 10463-528 6 X 2 Socket Reducer Saddle 40 6

12

15-2989 10851-020

2” Flg. One-Piece Socket - 150 lb. 80 2

15-2992

Installation, Operation & Service Manual

1

4”

TWO FILTER KIT SCHEDULE 80

(14-6403)

Item Pentair Part# AP PN Size Description Sch. Qty

1

15-3063 10854P-040 4 Flg.VS, Socket - 150lb. 80 2

2 15-0065 10856P-040 4 Flg.VS, Spigot - 150lb. 80 6

3 15-0066 1728-040 4 Butterfly Valve, Asahi SP 4

4 15-0067 REQ . 4

Hardware Kit - Valve/Flg.Hardware (#2)

1

Includes 32-5/8 x 6” hex head bolts,32-5/8” nuts, 64-5/8” washers

5 15-0069 10801-420 4 X 2 Socket Reducer Tee 80 4

6

15-0063

10827-020 2” Spig x Soc 45 Str. Elbow 80 4

7 15-0064 10878-020SR

2” Spigot Female Adapter,Spig x Fipt

80 4

8 27-1092 27-1092

2”Valve Adapter Kit

2

9

15-3057 10401-040 4 Socket Tee 80 1

10

15-3066 10806-040 4 90 Socket Elbow 80 1

11 15-3010 10463-420 4 X 2 Socket Reducer Saddle 40 6

12 15-2989 10851-020

2” Flg. One-Piece Socket - 150 lb. 80 2

15-2992

Installation, Operation & Service Manual

1

4” TWO FILTER KIT SCHEDULE 40

(14-6402)

Item

Pentair Part# AP PN Size Description Sch. Qty

1 15-3063 10854P-040 4 Flg.VS, Socket - 150lb. 80 2

2 15-0065 10856P-040 4 Flg.VS, Spigot - 150lb. 80 6

3 15-0066 1728-040 4 Butterfly Valve, Asahi SP 4

4 15-0067 REQ . 4

Hardware Kit - Valve/Flg.Hardware (#2)

1

Includes 32-5/8 x 6” hex head bolts,32-5/8” nuts, 64-5/8” washers

5 15-0068 10401-420 4 X 2 Socket Reducer Tee 40 4

6 15-0060 10427-020 2”Spig x Soc 45 Str. Elbow 40 4

7 15-0061 10478-020

2” Spigot Female Adapter,Spig x Fipt

40 4

8 27-1092 27-1092

2”Valve Adapter Kit

2

9 15-3012 10401-040 4 Socket Tee 40 1

10

15-3007 10406-040 4 90 Socket Elbow 40 1

11 15-3010 10463-420 4 X 2 Socket Reducer Saddle 40 6

12 15-2989 10851-020

2” Flg. One-Piece Socket - 150 lb. 80 2

15-2992

Installation, Operation & Service Manual

1

3” TWO FILTER KIT SCHEDULE 80

(

14-6401)

Item Pentair Part# AP PN Size Description Sch. Qty

1 15-3062 10854P-030 3 Flg.VS, Socket - 150lb. 80 2

2

15-0056 10856P-030 3 Flg.VS, Spigot - 150lb. 80 6

3 15-0057 1728-030 3 Butterfly Valve, Asahi SP 4

4

15-0058 REQ. 3

H

ardware Kit - Valve/Flg.Hardware (#1)

1

Includes 16-5/8 x 6” hex head bolts,16-5/8” nuts, 32-5/8” washers

5 15-0062 10801-338 3 X 2 Socket Reducer Tee 80 4

6 15-0063 10827-020 2”Spig x Soc 45 Str. Elbow 80 4

7 15-0064 10878-020SR

2” Spigot Female Adapter,Spig x Fipt

80 4

8

27-1092 27-1092

2

”Valve Adapter Kit

2

9 15-3056 10801-030 3 Socket Tee 80 1

10

15-3065 10806-030 3 90 Socket Elbow 80 1

11 15-3009 10463-338 3 X 2 Socket Reducer Saddle 40 6

12 15-2989 10851-020

2” Flg. One-Piece Socket - 150 lb. 80 2

15-2992

Installation, Operation & Service Manual

1

!

!

!

!

!

!

!

!

!

!

!

!

!

!

VALVED FILTER MANIFOLD

3

” TWO FILTER KIT SCHEDULE 40

(

14-7400)

Item Pentair Part# AP PN Size Description Sch. Qty

13 15-3062 10854P-030 3 Flg. VS, Socket - 150lb. 80 2

14 15-0056 10856P-030 3 Flg. VS, Spigot - 150lb. 80 6

1

5 15-0057 1728-030 3 Butterfly Valve, Asahi SP 4

16 15-0058 REQ. 3

Hardware Kit - Valve/Flg.Hardware (#1)

1

Includes 16-5/8 x 6” hex head bolts,16-5/8” nuts, 32-5/8” washers

17 15-3011 10401-030 3 Socket Tee 40 5

19 15-0075 10427-030 3” Spig x Soc 45 Str. Elbow 40 4

20 15-3009 10463-338 3 X 2 Socket Reducer Saddle 40 3

21 15-2989 10851-020

2” Flg. One-Piece Socket - 150lb Solid

80 1

22 15-0056 10856P-030 3” Flg. VS.Spigot - 150lb 80 4

23 15-0076 REQ.

3” Bolt Pack - Tank/Flg. Hdwr w/Gasket (#4)

1

Includes 16-5/8 x 6” hex head bolts,16-5/8” nuts, 32-5/8” washers

1

0470-030

a

nd 4 - 3” Neoprene FF Flg. Gaskets

24 15-3006 10406-030 3 90 Socket Elbow 80 1

15-2992

Installation, Operation & Service Manual

1

V

ALVED FILTER MANIFOLD

3

” TWO FILTER KIT SCHEDULE 80

(14-7401)

Item Pentair Part# AP PN Size Description Sch. Qty

13 15-3062 10854P-030 3 Flg. VS, Socket - 150lb. 80 2

14 15-0056 10856P-030 3 Flg. VS, Spigot - 150lb. 80 6

15 15-0057 1728-030 3 Butterfly Valve, Asahi SP 4

16 15-0058 REQ. 3

Hardware Kit - Valve/Flg.Hardware (#1)

1

Includes 16-5/8 x 6” hex head bolts,16-5/8” nuts, 32-5/8” washers

1

7 15-3056 10801-030 3 Socket Tee 80 5

1

9 15-0077 10827-030 3” Spig x Soc 45 Str. Elbow 80 4

20 15-3009 10463-338 3 X 2 Socket Reducer Saddle 40 3

21 15-2989 10851-020

2” Flg. One-Piece Socket - 150lb Solid

80 1

22 15-0056 10856P-030 3” Flg. VS.Spigot - 150lb 80 4

2

3 15-0076 REQ.

3

” Bolt Pack - Tank/Flg. Hdwr w/Gasket (#4)

1

I

ncludes 16-5/8 x 6” hex head bolts,16-5/8” nuts, 32-5/8” washers

10870-030

and 4 - 3” Neoprene FF Flg. Gaskets

24 15-3065 10806-030 3 90 Socket Elbow 80 1

15-2992

Installation, Operation & Service Manual

1

6” TWO FILTER KIT SCHEDULE 80

(

14-6405)

I

tem Pentair Part# AP PN Size Description Sch. Qty

1

15-3064 10854P-060 6 Flg.VS, Socket - 150lb. 80 2

2

15-0070 10856P-060 6 Flg.VS, Spigot - 150lb. 80 6

3 15-0071 1728-060 6 Butterfly Valve, Asahi SP 4

4 15-0073 REQ . 6

Hardware Kit - Valve/Flg.Hardware (#1)

1

Includes 32-3/4 x 7” hex head bolts,32-3/4” nuts, 64-3/4” washers

5 15-0074 10801-528 6 X 2 Socket Reducer Tee 80 4

6

15-0063 10827-020 2” Spig x Soc 45 Str. Elbow 80 4

7

15-0064 10878-020SR

2” Spigot Female Adapter,Spig x Fipt

80 4

8 27-1092 27-1092

2”Valve Adapter Kit

2

9 15-3059 10801-060 6 Socket Tee 80 1

101

5-3067 10806-060 6 90 Socket Elbow 80 1

11 15-3014 10463-528 6 X 2 Socket Reducer Saddle 40 6

12 15-2989 10851-020

2” Flg. One-Piece Socket - 150 lb. 80 2

15-2992

Installation, Operation & Service Manual

1

6” TWO FILTER KIT SCHEDULE 40

(14-6404)

Item Pentair Part# AP PN Size Description Sch. Qty

1 15-3064 10854P-060 6 Flg.VS, Socket - 150lb. 80 2

2 15-0070 10856P-060 6 Flg.VS, Spigot - 150lb. 80 6

3 15-0071 1728-060 6 Butterfly Valve, Asahi SP 4

4 15-0073 REQ . 6

Hardware Kit - Valve/Flg.Hardware (#1)

1

Inc

ludes 32-3/4 x 7” hex head bolts,32-3/4” nuts, 64-3/4” washers

5 15-0072 10401-528 6 X 2 Socket Reducer Tee 40 4

6 15-0060 10427-020 2”Spig x Soc 45 Str. Elbow 40 4

7 15-0061 10478-020

2” Spigot Female Adapter,Spig x Fipt

40 4

8 27-1092 27-1092

2”Valve Adapter Kit

2

9 15-3013 10401-060 6 Socket Tee 40 1

10

15-3008 10406-060 6 90 Socket Elbow 40 1

11

15-3014 10463-528 6 X 2 Socket Reducer Saddle 40 6

12

15-2989 10851-020

2” Flg. One-Piece Socket - 150 lb. 80 2

15-2992

Installation, Operation & Service Manual

1

4” TW

O FILTER KIT SCHEDULE 80

(14-6403)

Item Pentair Part# AP PN Size Description Sch. Qty

1

15-3063 10854P-040 4 Flg.VS, Socket - 150lb. 80 2

2 15-0065 10856P-040 4 Flg.VS, Spigot - 150lb. 80 6

3 15-0066 1728-040 4 Butterfly Valve, Asahi SP 4

4 15-0067 REQ . 4

Hardware Kit - Valve/Flg.Hardware (#2)

1

Includes 32-5/8 x 6” hex head bolts,32-5/8” nuts, 64-5/8” washers

5 15-0069 10801-420 4 X 2 Socket Reducer Tee 80 4

6

15-0063

10827-020 2” Spig x Soc 45 Str. Elbow 80 4

7 15-0064 10878-020SR

2” Spigot Female Adapter,Spig x Fipt

80 4

8 27-1092 27-1092

2”Valve Adapter Kit

2

9

15-3057 10401-040 4 Socket Tee 80 1

10

15-3066 10806-040 4 90 Socket Elbow 80 1

11 15-3010 10463-420 4 X 2 Socket Reducer Saddle 40 6

12 15-2989 10851-020

2” Flg. One-Piece Socket - 150 lb. 80 2

15-2992

Installation, Operation & Service Manual

1

!

!

!

!

!

!

!

!

VALVED FILTER MANIFOLD

3

” TWO FILTER KIT SCHEDULE 40

(

14-7400)

Item Pentair Part# AP PN Size Description Sch. Qty

13 15-3062 10854P-030 3 Flg. VS, Socket - 150lb. 80 2

1

4 15-0056 10856P-030 3 Flg. VS, Spigot - 150lb. 80 6

15 15-0057 1728-030 3 Butterfly Valve, Asahi SP 4

16 15-0058 REQ. 3

Hardware Kit - Valve/Flg.Hardware (#1)

1

Includes 16-5/8 x 6” hex head bolts,16-5/8” nuts, 32-5/8” washers

17 15-3011 10401-030 3 Socket Tee 40 5

1

9 15-0075 10427-030 3” Spig x Soc 45 Str. Elbow 40 4

20 15-3009 10463-338 3 X 2 Socket Reducer Saddle 40 3

21 15-2989 10851-020

2” Flg. One-Piece Socket - 150lb Solid

80 1

22 15-0056 10856P-030 3” Flg. VS.Spigot - 150lb 80 4

2

3 15-0076 REQ.

3

” Bolt Pack - Tank/Flg. Hdwr w/Gasket (#4)

1

Includes 16-5/8 x 6” hex head bolts,16-5/8” nuts, 32-5/8” washers

10470-030

and 4 - 3” Neoprene FF Flg. Gaskets

24 15-3006 10406-030 3 90 Socket Elbow 80 1

15-2992

Installation, Operation & Service Manual

1

6” TWO FILTER KIT SCHEDULE 80

(

14-6405)

Item Pentair Part# AP PN Size Description Sch. Qty

1 15-3064 10854P-060 6 Flg.VS, Socket - 150lb. 80 2

2

15-0070 10856P-060 6 Flg.VS, Spigot - 150lb. 80 6

3 15-0071 1728-060 6 Butterfly Valve, Asahi SP 4

4

15-0073 REQ. 6

H

ardware Kit - Valve/Flg.Hardware (#1)

1

Includes 32-3/4 x 7” hex head bolts,32-3/4” nuts, 64-3/4” washers

5

15-0074 10801-528 6 X 2 Socket Reducer Tee 80 4

6 15-0063 10827-020 2”Spig x Soc 45 Str. Elbow 80 4

7

15-0064 10878-020SR

2” Spigot Female Adapter,Spig x Fipt

80 4

8 27-1092 27-1092

2”Valve Adapter Kit

2

9 15-3059 10801-060 6 Socket Tee 80 1

10

15-3067 10806-060 6 90 Socket Elbow 80 1

1

1 15-3014 10463-528 6 X 2 Socket Reducer Saddle 40 6

12 15-2989 10851-020

2” Flg. One-Piece Socket - 150 lb. 80 2

15-2992

Installation, Operation & Service Manual

1

6”

TWO FILTER KIT SCHEDULE 40

(14-6404)

Item Pentair Part# AP PN Size Description Sch. Qty

1 15-3064 10854P-060 6 Flg.VS, Socket - 150lb. 80 2

2 15-0070 10856P-060 6 Flg.VS, Spigot - 150lb. 80 6

3 15-0071 1728-060 6 Butterfly Valve, Asahi SP 4

4 15-0073 REQ . 6

Hardware Kit - Valve/Flg.Hardware (#1)

1

Inc

ludes 32-3/4 x 7” hex head bolts,32-3/4” nuts, 64-3/4” washers

5 15-0072 10401-528 6 X 2 Socket Reducer Tee 40 4

6 15-0060 10427-020 2”Spig x Soc 45 Str. Elbow 40 4

7 15-0061 10478-020

2” Spigot Female Adapter,Spig x Fipt

40 4

8 27-1092 27-1092

2”Valve Adapter Kit

2

9 15-3013 10401-060 6 Socket Tee 40 1

10

15-3008 10406-060 6 90 Socket Elbow 40 1

11

15-3014 10463-528 6 X 2 Socket Reducer Saddle 40 6

12

15-2989 10851-020

2” Flg. One-Piece Socket - 150 lb. 80 2

15-2992

Installation, Operation & Service Manual

1

!

!

!

!

!

!

VALVED FILTER MANIFOLD

3

” TWO FILTER KIT SCHEDULE 40

(

14-7400)

I

tem Pentair Part# AP PN Size Description Sch. Qty

13 15-3062 10854P-030 3 Flg. VS, Socket - 150lb. 80 2

14 15-0056 10856P-030 3 Flg. VS, Spigot - 150lb. 80 6

15 15-0057 1728-030 3 Butterfly Valve, Asahi SP 4

16 15-0058 REQ. 3

Hardware Kit - Valve/Flg.Hardware (#1)

1

Includes 16-5/8 x 6” hex head bolts,16-5/8” nuts, 32-5/8” washers

1

7 15-3011 10401-030 3 Socket Tee 40 5

19 15-0075 10427-030 3” Spig x Soc 45 Str. Elbow 40 4

20 15-3009 10463-338 3 X 2 Socket Reducer Saddle 40 3

21 15-2989 10851-020

2” Flg. One-Piece Socket - 150lb Solid

80 1

22 15-0056 10856P-030 3” Flg. VS.Spigot - 150lb 80 4

23 15-0076 REQ.

3” Bolt Pack - Tank/Flg. Hdwr w/Gasket (#4)

1

I

ncludes 16-5/8 x 6” hex head bolts,16-5/8” nuts, 32-5/8” washers

1

0470-030

a

nd 4 - 3” Neoprene FF Flg. Gaskets

24 15-3006 10406-030 3 90 Socket Elbow 80 1

15-2992

Installation, Operation & Service Manual

1

6” TWO FILTER KIT SCHEDULE 80

(14-6405)

Item Pentair Part# AP PN Size Description Sch. Qty

1 15-3064 10854P-060 6 Flg.VS, Socket - 150lb. 80 2

2 15-0070 10856P-060 6 Flg.VS, Spigot - 150lb. 80 6

3 15-0071 1728-060 6 Butterfly Valve, Asahi SP 4

4 15-0073 REQ . 6

Hardware Kit - Valve/Flg.Hardware (#1)

1

Includes 32-3/4 x 7” hex head bolts,32-3/4” nuts, 64-3/4” washers

5 15-0074 10801-528 6 X 2 Socket Reducer Tee 80 4

6 15-0063 10827-020 2”Spig x Soc 45 Str. Elbow 80 4

7

15-0064 10878-020SR

2” Spigot Female Adapter,Spig x Fipt

80 4

8 27-1092 27-1092

2”Valve Adapter Kit

2

9 15-3059 10801-060 6 Socket Tee 80 1

10

15-3067 10806-060 6 90 Socket Elbow 80 1

11 15-3014 10463-528 6 X 2 Socket Reducer Saddle 40 6

12 15-2989 10851-020

2” Flg. One-Piece Socket - 150 lb. 80 2

15-2992

Installation, Operation & Service Manual

1

!

!

!

!

VALVED FILTER MANIFOLD

3” TWO FILTER KIT SCHEDULE 40

(14-7400)

Item Pentair Part# AP PN Size Description Sch. Qty

13 15-3062 10854P-030 3 Flg. VS, Socket - 150lb. 80 2

14 15-0056 10856P-030 3 Flg. VS, Spigot - 150lb. 80 6

15 15-0057 1728-030 3 Butterfly Valve, Asahi SP 4

16 15-0058 REQ. 3

Hardware Kit - Valve/Flg.Hardware (#1)

1

Includes 16-5/8 x 6” hex head bolts,16-5/8” nuts, 32-5/8” washers

17 15-3011 10401-030 3 Socket Tee 40 5

19 15-0075 10427-030 3” Spig x Soc 45 Str. Elbow 40 4

20 15-3009 10463-338 3 X 2 Socket Reducer Saddle 40 3

21 15-2989 10851-020

2” Flg. One-Piece Socket - 150lb Solid

80 1

22 15-0056 10856P-030 3” Flg. VS.Spigot - 150lb 80 4

23 15-0076 REQ.

3” Bolt Pack - Tank/Flg. Hdwr w/Gasket (#4)

1

Includes 16-5/8 x 6” hex head bolts,16-5/8” nuts, 32-5/8” washers

10470-030

and 4 - 3” Neoprene FF Flg. Gaskets

24 15-3006 10406-030 3 90 Socket Elbow 80 1

15-2992

Installation, Operation & Service Manual

1

TANDEM SYSTEM PLUMBING KIT PAGE 9

F. PARTS LIST FOR TR 100C & 140C FILTERS

10

9

4. Valve positioning is very important for your
system. Refer to the above diagrams when
changing valve positions. All four valves
must be in the proper position before apply­ing power to the system.

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

9

0

1

9

10

9

10

o

90 ELL

S

OCKET TEE

VALVED FILTER MANIFOLD

A. TR 100C/C3 and TR 140C/C3, remove

the 2” drain plug cap. The filter will
drain very slowly, and therefore, it is
recommended that the drain plug be
left out.

READ AND FOLLOW ALL SAFETY INSTRUCTIONS