FADER C LEA N I N G
The RM-100 faders may need lubrication from time to time. This will extend the
fader life and eliminate any potential damage due to extended heavy usage.
Cleaning Instructions
1. Remove the fader and disconnect the cable coming from the mixer. To remove
the crossfader, unsecrew the outer screws (removing the 2 inner screws will
detach the fader from the fader plate). To remove the line faders, remove all 4
screws.
2. Spray a small amount of cleaner or lubricant into both ends of the fader and
slide the fader back and forth a few times to spread the fluid evenly throughout
the fader.
3. Shake and wipe off excess fluid before re-assembling the fader.
FADE R R EPL AC E M E N T
To replace the cross or channel faders, follow step 1 of the cleaning instructions.
Replacement parts are available from Stanton or your local Stanton dealer.
CF-RM19 Crossfader
LF-RM19 Line input fader
RF-RM19 Line input rotary (dial) fader
PS-RM19US US Power Supply (110v)
PS-RM19EU European Power Supply (220v)
PS-RM19UK UK only Power Supply (240v)
RM-100
Professional performance mixer
© 2001, Stanton Magnetics, LLC
OWNER’S M A N U A L
STANTON MAGNETICS, LLC
info@stantonmagnetics.com
T RO U B LE S H O OTI N G
Thank you for making Stanton your first choice in professional DJ mixers.
This new, innovative family of mixers has been developed with input from the professional DJ community, bringing to the marketplace a previously unavailable, affordable combination of user-friendly, functional design, rugged construction, and professional quality features.
Stanton and your authorized Stanton dealer are dedicated to your complete satisfaction by offering benchmark service and support throughout the long life of your
Stanton product.
Again, we appreciate your patronage, and look forward to many years of making
music together.
PLEASE READ CAREFULLY BEFORE USE OF THIS PRODUCT
FA I LU R E TO FO L LOW T H E I N ST RU C TI O N S P R I N TE D B E LOW M AY VO I D WA R R A N T Y
• Follow all security advice printed on your mixer
• When removing the unit's AC plug from the power source, grasp and pull the
plug, NEVER the cord itself!
• Avoid placing your mixer near heat sources, such as power amplifiers.
• When in use, place your mixer on a stable surface, away from vibration. Always
use care when carrying your mixer. Impact, or heavy vibration may compromise
the unit's mechanical integrity. The manufacturer is not responsible for damage
resulting from an impact, or misuse.
• When in use, place your mixer away from sources of hum or noise, such as
transformers, or electric motors.
• To prevent overheating, always provide your mixer with adequate ventilation
air space.
• Avoid stepping on your mixer's AC cord. Repeated compression of the cord
may lead to electrical shorting.
• To avoid damage due to AC voltage peaks, always disconnect your mixer from
the power source during electrical storms.
• Your mixer contains no user-serviceable parts. The manufacturer is not
responsible for any damage or personal injury resulting from unauthorized
user-servicing or modifications. In addition, the warranty will be void if any
unauthorized service by the user is detected. Always return you mixer to an
authorized Stanton dealer for servicing.
Problem
Excessive hum when using
phono source.
Low frequency hum while
operating source unit.
Pro g ram volume can’t be
adjusted with master vo l u m e
c o n t ro l .
No powe r.
The amplifier is turned up,
but there is no signal.
No signal in headphones.
Cause
Poor ground connection.
Loose cartridge/headshell
connection.
Poor AC source ground.
Loose input/output connection. Shorted cable.
Amplifier or outboard gear
connected to the re c o rd output.
I m p roperly connected AC cord
or power line source not on.
B l own fuse.
Faulty output connections
Improper level adjustment.
Improper connection.
Improper level or cue mix
settings.
Solution
Properly connect turntable
ground wire to mixer ground
terminal.
Check cartridge connection
to headshell. Check headshell connection to tonearm.
Properly ground the AC
source. Check all input and
output connections for
s e c u re fit. Isolate and re p l a c e
the damaged cable.
Connect amplifier or outboard
gear to master output.
Properly connect AC cord to
AC power source. Turn powe r
o n .
Re m ove the fuse cover with a
flat-bladed scre wd r i ve r.
Replace fuse with a new
500mA fuse.
Properly connect amplifier, or
outboard gear to mixer.
Properly set crossfader,
channel faders, gain controls, and input selector toggles.
Check headphone connection to mixer. Tighten if necessary.
Adjust headphone level and
cue mix to the proper level
and channel settings.
D E S C R I P T ION O F FU N C TI O N S
1. Power switch: Selects power "ON" or "OFF".
2. BNC jack: 12V gooseneck light input
3. Mono/stereo switch: switches the of Master output between a stereo and mono signal
4. Master balance control: Controls left/right signal balance of the master output.
5. Master level control: Controls the overall signal output level of the master output.
6. Cue stereo/split switch: In "stereo" position, the pre-selected signal of switches (17)
and controls (9) and (11) will be monitored as a stereo signal in the headphones. In
"split" position, the pre-selected signal of switches ( 17) and controls ( 9) and ( 11)
will be monitored on one side of the headphones, and the master output signal on the
other side.
7. Booth level control: Controls the signal level of the booth output.
8. Headphone level control: Controls the overall headphone output level. It is recommended headphones with an impedance rating of 200 ohms or less be used for maximum volume.
9. Headphone output: Connection for 1/4 inch headphone. Recommended headphone
impedance is 32-200 ohms for maximum volume.
10. Cue pan assign: When this switch is"UP," the cue pan fader affects the headphone
output. While "DOWN," the cue pan fader affects the booth output.
11. Cue pan: Fades the headphone output between the channel(s) selected by the cue
assign switches (17) and the master one output, effectively allowing the user to preview a mix.
12. Send/return: Send and Return levels are used to control the volume of the external
effects unit used in the effects loop.
13. Crossfader source selectors: When set to A, the selecte channel will be assigned to
the left side of the crossfader. when set to B, the selected channel will be assigned to
the right side of the crossfader. When set to BYPASS, the crossfder will be bypassed
alltoghter.
14. Crossfader: Fades the master output between the channels selected by the
Crossfader source selectors (13).
15. Beat indicators: Illuminate according to the beat of the program music. The replacement of illumination varies depending on the style of music selected. This features
offers a helpful visual indicator of beat alignment.
16. Channel fader: Controls the input channel level.
17. Cue assign switch: Selects the channel to be monitored.
18. Fader Start: Turns the fader start function ON or OFF. The fader start will work with CD
players (such as Stanton’s S-Series) to start the audio from the CD player’s cue point.
19. Talkover attenuation control: Sets the amount of attenuation applied to the music
output signal when switch (20) is applied and the mic is spoken into. The attenuation
is adjustable from zero to 26 decibels.
20. Mic selector: Turns the mic on or off and activates the automatic talkover circuit.
When activated, the automatic talkover circuit reduces the music output based on the
setting of the talkover attenuation control (19).
21. FX switch: Turns effect send signal ON or OFF for each channel
22. Equalizer: Individual controls for low frequency, midrange, and high frequency
equalization with (+10/-10 dB) Note: Any changes made to EQ settings will change the
overall output level.
23. Microphone volume: Controls the output levels of mics 1 and 2
24. Input channel controls: Controls the input sensitivity of each channel and Hi, Mid,
and Low frequency equalization (+9/-26dB) of each channel.
25. Microphone 1 input: Combo XLR / 1/4” connector
26. Input selector switches: Selects phono or line input.
27. Auxilliary selectors: A. Enables monitoring of the effects loop through the headphones. B. Turns ON/OFF the efftects loop in the master output.
28. Output Level meter: Displays the o verall signal level of the master output.
29. Input Level meter: Displays the input level. The input level is determined by the input
channel controls (24).
30. Audio signal inputs: Line inputs are used to connect to line level sources such as CD
players, samplers, tape players, etc. Phono inputs are used to connect to turntables.
Mic inputs connect directly to microphones. To prevent potential circuit damage, never
connect line level source to phono inputs.
31. Fader Start connector: Connects to the sound module’s remote start output (such as
Stanton’s S-Series CD players) to control the cue-start via the mixer’s crossfader.
32. Audio signal outputs: Master output connects to an amplifier, EQ, crossover, or other
outboard signal processing. Record out connects to tape recorder, mini disk recorder,
etc. Booth output is a second master output used mostly for in-booth monitoring.
33. AC cord connector: Input connection for the supplied removable AC cord.
34. Send/return connetions: Connect the send output to the input of an outboard signal
processor, such as the Stanton DJF-1 DJ filter. Connect the return input to the output of
the outboard signal processor to create an effect loop.
TE C H N I C A L S P E C I FI C AT I O N S
Line inputs: 8 (RCA), 150 mV / 27K ohm
Phono inputs: 4 (RCA), 3 mV / 47K ohm
DJ mic input: 3 (XLR, 1/4“), 2.45 mV / 3K ohm
Effect Send: 1 (1/4”), 775mv
Effect Return: 1 (1/4”), 245mv
Master output: 1 (RCA), 1.2 V / 1K ohm
Booth output: 1 (RCA), 1.2 V / 1K ohm
Record output: 1 (RCA), 245 mV / 10K ohm
Headphone output: 1 (1/4”), 32 - 200 ohms recommended
Frequency Response: 20 Hz - 20 kHz, +/- 2 dB
Tone Control : + 9/-26 dB (Hi, Mid, Low)
Mic Tone: Hi/Mid/Lo +/-10 dB
Gain Control: 0-20dB
S/N Ratio: Less than 70dB
T.H.D: less than 0.2%
Dimension(LxWxD): 19” x 10.5” x 4” (482 x 267 x 102 mm)
WA R R A N T Y
This unit has been designed and manufactured using quality
components. Therefore, it is warranted to be free from defects in materials (limited as specified below), and workmanship for a period of twelve
(12) months from the original purchase date. During this period, all
service and parts necessary to repair a defect will be free of charge. This
limited warranty applies to mechanical parts which are subject to wear
and tear as specified:
• Faders, specified durability: 15,000 cycles
• Rotary potentiometers, specified durability: 10,000 cycles
• Switches, specified durability: 10,000 cycles
Consequently, the parts listed above are warranted to be free from
defects in materials and workmanship for a period of thirty days (30)
days from the original purchase date.
FOR THE WA R R A N TY TO BE VA LID, PLEASE CO M PLE T E THE
O N LINE WA R R A N TY REGIST R ATION FORM FOUND AT
W W W. STA N TO N M AG N E TI CS . CO M
Stanton Magnetics, LLC,
Hollywood, FL 33020
Loading...