M.212
USER’S MANUAL
IMPORTANT SAFETY PRECAUTIONS
1. Read Instructions – All the safety and operating instructions should be read
before this product is operated.
2. Retain Instructions – The safety and operating instructions should be retained
for future reference.
3. Heed Warnings – All warnings on the appliance and in the operating
instructions should be adhered to.
4. Follow Instructions – All operating and use instructions should be followed.
5. Water and Moisture – The appliance should not be used near water - for
example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet
basement, or near a swimming pool, and the like.
6. Heat – Appliance should be situated away from heat sources such as
radiators, heat registers, stoves, or other appliances (including amplifiers) that
produce heat.
7. Power Sources – This product should be operated only from the type
of power source indicated on the rating label. If you are not sure of the type
of power supply to your home, consult your product dealer or local power
company. For products intended to operate from battery power, or other
sources, refer the operating instructions.
8. Grounding or Polarization – This product may be equipped with a polarized
alternation-current line plug (a plug having one blade wider than the other).
This plug will fit into the power outlet only one way. This is a safety feature.
If you are unable to insert the plug fully into the outlet, try reversing the plug.
If the plug should still fail to fit, contact your electrician to replace your obsolete
outlet. Do not defeat the safety purpose of the polarized plug.
9. Power-Cord Protection – Power-supply cords should be routed so that they
are not likely to be walked on or pinched by items placed upon or against them,
paying particular attention to the cord in correspondence of plugs, convenience
receptacles, and the point where they exit from the appliance.
10. Cleaning – The appliance should be cleaned only as recommended by the
manufacturer. Clean by wiping with a cloth slightly damp with water. Avoid
getting water inside the appliance.
11. Non-use Periods – The power cord of the appliance should be unplugged from
the outlet when left unused for a long period of time.
12. Object and Liquid Entry – Care should be taken so that objects do not fall
and liquids are not spilled into the enclosure through openings.
13. Damage Requiring Service – The appliance should be serviced by qualified
service personnel when:
A. The power-supply cord or the plug has been damaged; or
B. Objects have fallen, or liquid has been spilled into the appliance; or
C. The appliance has been exposed to rain; or
D. The appliance does not appear to operate normally or exhibits a marked
change in performance; or
E. The appliance has been dropped, or the enclosure damaged.
14. Servicing – The user should not attempt any service to the appliance beyond
that described in the operating instructions. All other servicing should be
referred to qualified service personnel.
15. Ventilation – Slots and openings in the cabinet are provided for ventilation and
to ensure reliable operation of the product and to protect it from overheating,
and these openings must not be blocked or covered. The openings should
never be blocked by placing the product on a bed, sofa, rug, or other similar
surface. This product should not be placed in a built-in installation such as
a bookcase or rack unless proper ventilation is the manufacturer’s instructions
have been adhered to.
16. Attachments – do not use attachments not recommended by the
product manufacturer as they may cause hazards.
17. Accessories – Do not place this product on an unstable cart, stand,
tripod, bracket, or table. The product may fall, causing serious injury to a child
or adult, and serious damage to the product. Use only with a cart, stand, tripod,
bracket, or table recommended by the manufacturer, or sold with the
product. Any mounting of the product should follow the manufacturer’s
instructions,and should use a mounting accessory recommended by the
manufacturer.
18. Replacement Parts – When replacement parts are required, be sure the
service technician has used replacement parts specified by the
manufacturer or have the same characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock, or other hazards.
19. Safety Check – Upon completion of any service or repairs to this product, ask
the service technician to perform safety checks to determine that the product is
in proper operating conditions.
20. This product is in compliance with EU WEEE regulations. Disposal of end of
life product should not be treated as municipal waste. Please refer to your local
regulations for instructions on proper disposal of this product.
21. Carts and Stands – The appliance should be used only with a cart or stand
that is recommended by the manufacturer. An appliance and cart
combination should be moved with care. Quick stops, excessive force, and
uneven surfaces may cause the appliance and cart combination to overturn.
CAUTION: To reduce the risk of electric shock, do not remove any cover.
No user-serviceable parts inside. Refer servicing to qualified service personnel only.
The lightning flash with arrowhead symbol within the equilateral triangle is intended to alert the user to the presence of un-insulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock.
The exclamation point within the equilateral triangle is intended to alert the user to the presence of important operation and maintenance (servicing) instructions in the literature accompanying this appliance.
CAUTION: To prevent electric shock, do not use this polarized plug with an extension cord, receptacle or other outlet unless the
blades can be fully inserted to prevent blade exposure.
II
Thank you for purchasing Stanton’s newest innovation in professional tabletop mixer. The M.212 mixer was designed to bring style and reliability to the
mobile or club DJ at an affordable cost.
2 bend EQ w/ input GAIN control per channel.
Fader Start
Power on/off muting
Long Life crossfader
Crossfader curve control
Checking Package Contents
INTRODUCTION
MAIN FEATURES
ACCESSORIES
Check that the carton contains the following items:
(1) M.212 Mixer
(2) AC adaptor
(3) User's Manual
1
CONTROL OVERVIEW TOP PANEL
1. Channel Gain - Adjusts the pre-fader volume for cleaner
sound. Reduce the channel gain if you notice the level
indicators flashing red.
2. Mic Input Gain - Adjusts microphone input level.
3. Mic EQ - The mic channel includes a two-band EQ with a
range of +10 dB to -10 dB.
4. Channel EQ - Adjusts the high, mid and low frequency
levels of the input channels for either making the treble or
bass louder or to be used as an effect.
5. Input Fader - Controls individual source levels (channels) in
the mix.
6. Crossfader Curve - The CUT setting allows the use of the
crossfader for quick cut in and out when scratching and
mixing. The FADE setting is used for longer
typically when mixing between
7. Crossfader - Used to mix the sound from both channels.
8. Mic Input - Insert your ¼” microphone plug here.
two beat-matched sources.
segues,
9. Headphone Input - Insert your ¼” headphone plugs here.
10. Fader Start On/Off Switch - When the unit has been
connected to a CD player using a control cable, this
becomes the On/Off switch to automatically start and stop
the CD player while using the crossfader.
11. Level Indicators - The dual LED indicators are used to
indicate the master output level of the Right and Left
channels.
12. Channel Cue / Cue Pan - Used to preview channel audio
to your headphones. Listen here before bringing up
channel faders or moving the crossfader.
13. Headphone Level - Adjusts
14. Master Level
15. Input Toggle Switch - Selects which source will be active
based on what you have connected to the rear panel input
section (phono/line).
2
- Controls the overall output level.
cue volume.
CONTROL OVERVIEW REAR PANEL
DC 6V
16. Power Switch - Turns unit off and on.
17. Power Connector - Plug in the included power supply here.
18. Fader Start Control Jacks - Connect these jacks to the Fader input jacks of the CD player using the 3.5mm stereo mini cord.
19. Master Output - Unbalanced RCA connectors controlled by the Master level.
20. Line Inputs - Unbalanced RCA jacks for connecting stereo audio from line level sources such as CD players, HiFi VCRs,
cassette decks, DAT machines, laser discs, tuners, even synthesizers or other mixing consoles.
Note: Plug mono audio sources into both Left and Right inputs using a "Y" cable connector.
21. Phono Inputs - Plug your turntables in here. When these connectors are used, your signal is fed directly to the high-quality
RIAA phono pre-amplifiers. Use this position only for turntables. Line level sources will overload the sensitive phono preamps
and will cause distortion.
22. GND - Connect each of your turntable ground leads to either of the two ground terminals.
3
QUICK SETUP DIAGRAM
Review this setup diagram. Make sure all faders are at "zero" and all devices are off. First, connect all input sources and processors. Next, connect your
microphone and monitor headphones. Finally, connect the stereo outputs to the power amplifier(s) and/or audio receivers such as tape decks. Plug your
mixer into AC power. Now you are ready to switch everything on.
IMPORTANT: Always switch on your audio input sources, such as turntables or CD players first, then your mixer, and finally any amplifiers. When turning
off, always reverse this operation by turning off amplifiers, then your mixer, and then input devices.
Turntable
Power
Supply
Turntable
DC 6V
CD Player Controller
DAT, etc.
Power Amp.
4
Input / output impedance & sensitivity: (Master 0 dBV output, load= 100k ohm, Max, Gain, EQ flat)
Line 10k ohm /-14 dBV (200 mV) +/-2 dB
Phono 47k ohm /-50 dBV (3.16mV) +/-2 dB
Mic 2.2k ohm /-60 dBV (1mV) +/-2 dB
Master 1k ohm
Phones 33 ohm / 0 dBV (1V) ±2 dB
Max. output (THD= 1%, Maximum gain, EQ flat)
Master More than +18 dBV (8.0V) at load= 100k ohm
Phones More than +4 dBV (1.6V) at load= 32 ohm
Channel balance: Within 3 dB
Frequency response: (Master output, EQ flat)
Line 20-20 kHz +/- 2 dB
Phono 20-20 kHz +2, -3 dB (RIAA)
Mic 20-20 kHz +2/-3 dB
S/N ratio: (Maximum gain, master 0 dBV output, EQ flat, w/20 kHz LPF, A-weighted)
Line Less than -80 dBV
Phono Less than -70 dBV
Mic Less than -60 dBV
THD + N: (Master 0 dBV output, maximum gain, w/ 20 kHz LPF)
SPECIFICATIONS
Line Less than 0.05% 20 - 20 kHz
Phono Less than 0.1% 20 - 20 kHz (IEC-A WTD)
Mic Less than 0.2% 20 - 20 kHz (IEC-A WTD)
Phones Less than 0.1% 20 - 20 kHz (From line input)
Crosstalk: (From master output, A-weighted)
Line/Phono More than 70 dB at 1 kHz between L and R
More than 70 dB at 1 kHz between channels
MIC EQ:
Hi 10 +/- 2 dB at 10 kHz
-10 +/- 2 dB at 10 kHz
Low 10 +/- 2 dB at 100 Hz
-10 +/- 2 dB at 100 Hz
Channel EQ:
Hi 9 +/- 2 dB at 13 kHz
-15 +/- 3 dB at 13 kHz
Mid 9 +/- 2 dB at 1 kHz
Less than -23 dB at 1 kHz
Low 9 +/- 2 dB at 70 Hz
-26 +/- 3 dB at 70 Hz
Power Source: DC 6V
Dimensions: 230 (W) X 267 (D) X 111 (H) mm
Weight: 1.65 kg
5
Warranty
Through Stanton’s authorized dealers around the World, Stanton, or one of Stanton’s authorized distributors outside the U.S., will, without charge,
repair or replace, at the sole discretion of the entity responsible for making the repair or providing the replacement, any Stanton merchandise proved
defective in material or workmanship for a period of one year following the date of original purchase. Exceptions to this warranty are as noted below:
The warranty for mechanical parts which are subject to wear and tear are limited to the earlier of either thirty (30) days following the date of original
purchase or the following number of cycles: Faders - 15,000; Rotary potentiometers - 10,000; and Switches - 10,000.
Stanton will warrant all replacement parts and repairs for ninety (90) days from the date of original shipment. Repairs made necessary by reason of
misuse, alteration, normal wear, or accident are not covered under this warranty.
Returns
Authorized Stanton dealers are only authorized to sell and distribute merchandise within a specific country. All goods requiring warranty repair or
replacement must be returned (freight prepaid if not hand-delivered) to the authorized Stanton dealer from whom the merchandise was purchased
and in the same country where the merchandise was purchased. For purposes of purchases made via the Internet, the merchandise must be
returned to the authorized Stanton dealer in the country where the authorized Stanton dealer which sold the merchandise to purchaser is located and
not the authorized Stanton dealer in the country where the purchaser is located or the country in which the merchandise was received. Any returns
to a non-authorized dealer or to an authorized Stanton dealer not in the same country as the merchandise was intended to be sold or as set forth
above will void this warranty.
To initiate a warranty repair, you must contact the authorized Stanton dealer from whom you purchased the merchandise, and follow such authorized
Stanton dealer’s return policy.
Stanton assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the
merchandise. Stanton’s liability for any claim, whether based on breach of contract, negligence, infringement of any rights of any party, or product
liability, and relating to the merchandise shall not exceed the price received by Stanton from your purchase of such merchandise. In no event will
Stanton be liable for any special, incidental or consequential damages (including loss of use, loss of profit and claims of third parties) however
caused, whether by the negligence of Stanton or otherwise. To the extent permitted by law and except as otherwise provided above, Stanton
disclaims any express or implied warranties of merchantability or fitness for a particular purpose.
WARRANTY & RETURN POLICY
The above warranty provides you with specific legal rights. You may also have additional rights, which are subject to variation from state to state and
country to country.
If there is a dispute regarding the warranty of merchandise that does not fall under the warranty conditions stated above, please include a written
explanation with the merchandise when returned pursuant to the terms and conditions set forth herein.
Please register your product online at www.stantondj.com
Stanton Magnetics
772 S. Military Trail
Deerfield Beach, FL 33442
Phone: +1 (954) 949-9600
Technical Support: service@stantonmagnetics.com
LITS00055 11/12/09
Loading...