Stamina UX2 User Manual

Owner's

Manual

!

WARNING

Exercise can present a
health risk. Consult a
physician before beginning
any exercise program with
this equipment. If you feel
faint or dizzy, immediately
discontinue use of this
equipment. Serious bodily
injury can occur if this
equipment is not assembled
and used correctly. Serious
bodily injury can also occur
if all instructions are not
followed. Keep others and
pets away from equipment
when in use. Always make
sure all bolts and nuts are
securely tightened prior to
each use. Follow all safety
instructions in this manual.

Product May Vary Slightly From Pictured.

CAUTION:
Weight on this product should not exceed 250 lbs.

This Product is Distributed Exclusively by

2040 N. Alliance, Springeld, MO 65803

Customer Service

1 [phone]

www.staminaproducts.com

When calling for parts or

service, please specify

the following number

:

Model#: 15-0881

STAMINA PRODUCTS

MADE IN CHINA

© 2013 Stamina Products, Inc.

2013, 03

TABLE OF CONTENTS

Safety Instructions ...................................... 2

Before You Begin ........................................ 4

Equipment Warning, Caution & Notice Labels ... 5

Hardware Identication Chart .................... 6

Assembly Instructions ................................ 7

Set Up Instructions ................................... 11

Operational Instructions ........................... 12

Storage ....................................................... 14

Adjustment Instructions ........................... 16

Conditioning Guidelines ........................... 18

Warm-Up and Cool-Down ......................... 19

Product Parts Drawing .............................. 20

Parts List .................................................... 21

Warranty ..................................................... 23

Notes ........................................................... 24

Fax/Mail Ordering Form ............................ 26

Maintenance ............................................... 15

SAFETY INSTRUCTIONS

!

WARNING

!

WARNING

!

WARNING

1. Read all warnings and cautions posted on the STAMINA® UX2 Air Bike.

2. The STAMINA® UX2 Air Bike should only be used after a thorough review of the Owner’s Manual. Make

sure that it is properly assembled and tightened before use.

3. We recommend that two people be available for assembly of this product.

4. Keep children away from the STAMINA® UX2 Air Bike. Do not allow children to use or play on the
STAMINA® UX2 Air Bike. Keep children and pets away from the STAMINA® UX2 Air Bike when it is in
use.

5. The STAMINA® UX2 Air Bike is not a freewheeling exercise bike; therefore, pedal speed should be
reduced in a controlled manner to prevent injury from spinning pedals.

6. Remain seated, do not stand up on the pedals while riding the STAMINA® UX2 Air Bike. Failure to do so
could result in serious injury.

7. It is recommended that you place this exercise equipment on an equipment mat.

8. Set up and operate the STAMINA® UX2 Air Bike on a solid level surface. Do not position the STAMINA®
UX2 Air Bike on loose rugs or uneven surfaces.

9. Make sure that adequate space is available for access to and around the STAMINA® UX2 Air Bike.

10. Adjust the Leveling Caps(48) on the Front Stabilizer(3) so that the bike sits on the oor without rocking.

11. Before using, inspect the STAMINA® UX2 Air Bike for worn or loose components, and securely tighten or

replace any worn or loose components prior to use.

12. Before getting on the STAMINA® UX2 Air Bike, always check the Seat Post(4), Pedals(31, 32), and

Handlebars(6, 7, & 8) to be sure they are secure. The Locking Knob(46) must be inserted into one of the
holes in the Seat Post(4) and securely tightened.

13. Each user should adjust the seat per instructions on page 13.

14. Do not attempt to adjust the seat while you are on the STAMINA® UX2 Air Bike.

15. Consult a physician prior to commencing an exercise program and follow his/her recommendations in

developing your tness program. If at any time during exercise you feel faint, dizzy, or experience pain, stop

and consult your physician.

16. Always choose the workout which best ts your physical strength and exibility level. Know your limits and

train within them. Always use common sense when exercising.

17. Do not wear loose or dangling clothing while using the STAMINA® UX2 Air Bike.

18. Never exercise in bare feet or socks; always wear proper footwear such as running, walking, or cross

training shoes that t well, provide foot support, and feature non-skid rubber soles.

19. Be careful to maintain your balance while using, mounting, dismounting, or assembling the STAMINA® UX2
Air Bike, loss of balance may result in a fall and serious bodily injury.

20. The STAMINA® UX2 Air Bike should not be used by persons weighing over 250 pounds.

21. The STAMINA® UX2 Air Bike should be used by only one person at a time.

22. The STAMINA® UX2 Air Bike is for consumer use only. It is not for use in public or semipublic facilities.

This product contains a chemical known to the State of California to cause
cancer and birth defects or other reproductive harm.
Consult your physician before starting this or any exercise program. This is

especially important if you are over the age of 35, have never exercised before,

are pregnant, or suffer from any health problem. This product is for home use
only. Do not use in institutional or commercial applications. Failure to follow
all warnings and instructions could result in serious injury or death.
To reduce the risk of serious injury, read the following Safety Instructions
before using the STAMINA® UX2 Air Bike.

2

Call Us First

www.staminaproducts.com

1 [phone]

Customer Service

THANK YOU FOR PURCHASING THE

STAMINA® UX2 Air Bike

To enact your warranty, please register your product

by going to register.staminaproducts.com

To help you get started, we have pre-assembled most of your

STAMINA® UX2 Air Bike at the factory with the exception

of those few parts left unassembled for shipping purposes.

Simply follow the few assembly instructions set forth in this manual.

With regular workouts, you will be getting your body into shape

and be on your way to achieving a happier and healthier lifestyle.

Should you have any questions,

please call our Customer Service Department toll-free number,

Monday - Thursday, 7:30 A.M. - 5:00 P.M., Central Time.

Friday, 8:00 A.M. - 3:00 P.M., Central Time.

1 [phone]

ONLINE

CUSTOMER SERVICE

[e-mail]

www.staminaproducts.com

TELEPHONE

CUSTOMER SERVICE

Tel: [phone]

3

FAX

CUSTOMER SERVICE

Fax: [phone]

MAIL

STAMINA PRODUCTS, INC.

ATTN: Customer Service

P.O. Box 1071

Springeld, MO. 65801-1071

BEFORE YOU BEGIN

Thank you for choosing the STAMINA® UX2

Air Bike. We take great pride in producing this

quality product and hope it will provide many hours
of quality exercise to make you feel better, look
better, and enjoy life to its fullest.

It's a proven fact that a regular exercise program
can improve your physical and mental health.
Too often, our busy lifestyles limit our time and
opportunity to exercise. The STAMINA® UX2 Air
Bike provides a convenient and simple method to
begin your journey of getting your body in shape
and achieving a happier and healthier lifestyle.

Before reading further, please review the
drawing below and familiarize yourself with the
parts that are labeled.

Read this manual carefully before using the

STAMINA® UX2 Air Bike.

Foam Grip

Left Handlebar

Although Stamina constructs its products with

the nest materials and uses the highest standards

of manufacturing and quality control, there can
sometimes be missing parts or incorrectly sized
parts. If you have any questions or problems with
the parts included with your STAMINA® UX2 Air
Bike, please do not return the product. Contact us
FIRST!

If a part is missing or defective, please go to
staminaproducts.com under the Service section
and order the part needed, or call us toll free

at 1-800-375-7520 (in the U.S.). Our Customer

Service Staff is available to assist you from 7:30
A.M. to 5:00 P.M. (Central Time) Monday through
Thursday and 8:00 A.M. to 3:00 P.M. (Central
Time) on Friday.

Be sure to have the name and model number of
the product available when you contact us.

Foam Grip

Tension Knob

Seat

Seat Post

Main Frame

Warning Label

Endcap

Crank

Rear Stabilizer

THE FOLLOWING TOOLS ARE INCLUDED FOR ASSEMBLY :

Right Handlebar

Meter

Fan Cage

Right Chain Guard

Lower Bar

Leveling Cap

Linkage

Right Pedal

Wrench

Multi-opening Wrench

Allen Wrench (6mm)

4

EQUIPMENT WARNING, CAUTION & NOTICE LABELS

This chart is provided to help identify the warning, caution, and notice labels on the STAMINA® UX2
Air Bike. Please take a moment to familiarize yourself with all of the warning, caution, and notice

labels.

Label is larger than actual size

WARNING LABEL(73)W1

5

HARDWARE IDENTIFICATION CHART

This chart is provided to help identify the hardware used in the assembly process. Place the washers or

the ends of the bolts or screws on the circles to check for the correct diameter. Use the small scale to

check the length of the bolts and screws.

3/16"

1/4" 5/16" 3/8" 1/2"

INCHES

0 1/2

1 1/2 2 1/2 3 1/2 4 1/2 5 1/2 6

in.

mm.

0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150

length

6 8

10 12

MILLIMETERS

NOTICE: The length of all bolts and screws, except those with flat

heads, is measured from below the head to the end of the bolt

length

or screw. Flat head bolts and screws are measured from the
top of the head to the end of the bolt or screw.

After unpacking the unit, open the hardware bag and make sure that you have all the following items.
Some hardware may be already attached to the part.

Part No. and Description Qty

51 Carriage Bolt (M8 x 1.25 x 38mm) 2

57 Screw, Round Head (M5 x 0.8 x 12mm) 4

58 Screw, Flat Head (M5 x 0.8 x 15mm) 1

59 Bolt, Round Head (M6 x 1 x 12mm) 4

35 Thin Nut (1/2” - 20) 2

62 Nylock Nut (M8 x 1.25) 5

64 Acorn Nut (M8 x 1.25) 2

70 Arc Washer (M6) 4
71 Arc Washer (M8) 2

33 Pedal Washer (1/2”) 2
38 Bushing Washer (ø16.3 x ø25 x 0.5t) 2
39 Large Washer (M8) 2
67 Washer (M8 x ø16mm x 1.5mm) 3

6

ASSEMBLY INSTRUCTIONS

Place all parts from the box in a cleared area and position them on the oor in front of you. Remove

all packing materials from your area and place them back into the box. Do not dispose of the packing
materials until assembly is completed. Read each step carefully before beginning. If you are missing
a part, please go to staminaproducts.com under the Service section and order the part needed,

e-mail us at [e-mail], or call us toll free at 1-800-375-7520 (in the
U.S.). Our Customer Service Staff is available to assist you from 7:30 A.M. to 5:00 P.M. (Central

Time) Monday through Thursday and 8:00 A.M. to 3:00 P.M. (Central Time) on Friday.

STEP 1

Insert REAR STABILIZER(2) into the MAIN FRAME(1) and fasten with ROUND HEAD SCREWS

(M5x0.8x12mm)(57).

STEP 2

Attach FRONT STABILIZER(3) to the MAIN FRAME(1) with CARRIAGE BOLTS(M8x1.25x38mm)(51),
ARC WASHERS(M8)(71), and ACORN NUTS(M8x1.25)(64).

STEP 3

Turn the LEVELING CAPS(48) on the FRONT STABILIZER(3) as needed until bike is steady and not rocking.

7

ASSEMBLY INSTRUCTIONS

STEP 4

Attach the SEAT(43) to the SEAT POST(4) with NYLOCK NUTS(M8x1.25)(62) and WASHERS(M8)(67).
Insert the SEAT POST(4) into the MAIN FRAME(1) and lock in position with LOCKING KNOB(46).

8

ASSEMBLY INSTRUCTIONS

STEP 5

There is a “R” decal on the RIGHT HANDLEBAR(7) and RIGHT LOWER BAR ASSEMBLY(8, 9). Attach
the LOWER BAR(8) to the RIGHT HANDLEBAR(7) with ROUND HEAD BOLTS(M6x12mm)(59) and

ARC WASHERS(M6)(70). Repeat to assemble the LEFT HANDLEBAR(6) and LEFT LOWER BAR
ASSEMBLY(8, 9).

STEP 6

Slide the AXLE(36) through BUSHINGS(37) into the MAIN FRAME(1). Slide the two BUSHING
WASHERS(38) onto both sides of the AXLE(36). Slide the LEFT and RIGHT HANDLEBARS(6, 7), with the
grips facing outside, onto AXLE(36) and fasten with LARGE WASHERS(M8)(39) and NYLOCK NUTS(M8)
(62). Place a NUT CAP(40) onto the NYLOCK NUT(M8)(62) on both sides.

STEP 7

Slide the two FOAM GRIPS(41) onto the LEFT and RIGHT HANDLEBARS(6, 7).
NOTE: Lubricate the LEFT and RIGHT HANDLEBARS(6, 7) with a small amount of liquid soap for easier

installation of the FOAM GRIPS(41).

L

R

L

R

9

ASSEMBLY INSTRUCTIONS

IMPORTANT STUDY THE FOLLOWING ILLUSTRATION AND READ ALL OF STEP 8 “a” through

“f” BEFORE ATTACHING PEDALS AND CONNECTING LINKAGES.

STEP 8

NOTE: The RIGHT PEDAL(32) has R marked on the bottom side of the pedal. The LEFT PEDAL(31) has

L marked on the bottom side of the pedal. Both PEDALS(31, 32) have RIGHTHAND THREADS.

Tighten both PEDALS(31, 32) by turning clockwise.

a. Slide the two PEDAL WASHERS(1/2”)(33) onto both PEDAL SHAFTS of PEDALS(31, 32).
b. Insert PEDAL SHAFTS of PEDALS(31, 32) through the LINKAGES(9).
c. Slide SPACERS(34) onto PEDAL SHAFTS.
WARNING: SPACERS(34) must be between LINKAGES(9) and CRANK(10) so that there will be enough

clearance between LINKAGES(9) and CRANK(10).
d. Thread PEDAL SHAFTS of PEDALS(31, 32) into CRANK(10) and securely tighten.
e. Hold PEDAL SHAFTS and thread THIN NUTS(1/2”-20)(35) onto PEDAL SHAFTS.
f. Tighten PEDAL SHAFTS and THIN NUTS(1/2”-20)(35) until THIN NUTS(1/2”-20)(35) are tight.

STEP 9

Install two AA batteries into the METER(47), the batteries are not included. See page 12 for detailed battery
installation instructions. Plug the SPEED PICKUP WIRE(23) into the connecting wire on the METER(47).
Slide the METER(47) onto the plate on the MAIN FRAME(1).

NOTE: Be careful not to damage the wires when attaching the METER(47).

10

SET UP INSTRUCTIONS

Place the STAMINA® UX2 Air Bike in the area where it will be used. It is recommended that
the STAMINA® UX2 Air Bike be placed on an equipment mat. The STAMINA® UX2 Air Bike is
approximately 42.5 inches long (max.) x 22.3 inches wide x 45.3 inches tall. (These dimensions may vary
up to one inch.) An area 4 feet wide x 6 feet long is required for safe operation of the STAMINA® UX2

Air Bike. Make sure that adequate space is available for access to and passage around the STAMINA®
UX2 Air Bike.

LEVELING: Adjust the LEVELING CAPS(48) on the FRONT STABILIZER(3) so that the STAMINA®

UX2 Air Bike sits on the floor without rocking. Remove and reposition the LEVELING
CAPS(48) so the at side of both caps are in contact with the oor.

MOVING: To move the STAMINA® UX2 Air Bike, it is recommended that two people move the bike

together.

EQUIPMENT MAT

FUNCTION INSPECTION:

Visually inspect the STAMINA® UX2 Air Bike to verify that assembly is as shown in the above
illustration. Check the function of the STAMINA® UX2 Air Bike by turning the crank slowly through one
complete revolution to verify that the drive train functions properly. Adjust the TENSION KNOB(27) and
verify that it functions properly and the resistance changes.

CAUTION: Locate and read the WARNING LABEL(73) on the STAMINA® UX2 Air Bike. Make sure

that all users read the WARNING LABEL(73) before using the product.

11

OPERATIONAL INSTRUCTIONS

USING THE FITNESS METER

POWER ON :

POWER OFF :

Pedal movement or press the button.

Automatic shut off after four minutes of
inactivity.

MODE/RESET BUTTON:

Press to select display functions, include SCAN, TIME,
SPEED, DISTANCE, and CALORIES.

Press and hold for three seconds to reset all functions to
zero.

FUNCTIONS:

SCAN:

TIME:

Automatically scans each function of TIME, SPEED, DISTANCE, and CALORIES in
sequence with change every four seconds. Press and release the button until "SCAN"
appears on the display.

Displays the time from one second up to 99:59 minutes.

SPEED:

DISTANCE:

CALORIES:

NOTE:

Displays the current speed from zero to 999.9 miles per hour.

Displays the distance from zero to 99.99 miles.

Displays the calories burned from zero to 999.9 Kcal.
The calorie readout is an estimate for an average user. It should be used only as a
comparison between workouts on this unit.

The meter will shut off automatically after four minutes of inactivity. All function values
will be kept. Press the button and hold it down for three seconds to reset all functions
to zero.

HOW TO INSTALL AND REPLACE BATTERIES:

1. Open the Battery Door on the back of the meter.

2. The meter operates with two AA batteries, the batteries are not

included. Refer to the illustration to install or replace the batteries.

NOTE:

1. Do not mix a new battery with an old battery.

2. Use the same type of battery. Do not mix an alkaline battery with

another type of battery.

3. Rechargeable batteries are not recommended.

AA Batteries

12

OPERATIONAL INSTRUCTIONS

SEAT HEIGHT ADJUSTMENT

Proper seat height is important for efcient exercise. To determine proper seat height, sit on the bike and

center the ball of your foot on the pedal in the down position. Your leg should be slightly bent and relaxed
as shown.

If your leg is too straight or your foot cannot touch the pedal, you will need to lower the seat. If your leg
is bent too much you will need to raise the seat. Remove the LOCKING KNOB(46). Lower or raise the
SEAT(43) to the desired height and secure with the LOCKING KNOB(46).

CAUTION: The LOCKING KNOB(46) must be inserted into one of the holes in the SEAT POST(4).

NOTE: The LOCKING KNOB(46) should be screwed in tight to make the SEAT POST(4) t securely

in the MAIN FRAME(1).

LOAD ADJUSTMENT

To increase the load, turn the TENSION KNOB(27) clockwise.
To decrease the load, turn the TENSION KNOB(27)
counterclockwise.
NOTE: The load will increase as you pedal faster.

13

OPERATIONAL INSTRUCTIONS

Exercise Workout

The secret to aerobic training is achieving a selected heart rate and maintaining it. The STAMINA® UX2
Air Bike

, with its air resistance system allows the user to easily attain the desired pulse rate.

Since no two people or life styles are alike, the
user to isolate portions of the body that may need greater emphasis in training.

These exercises provide cardiovascular conditioning, muscle toning and joint exing with the ability to

exercise both the upper and lower body simultaneously or independently. Increase the workout intensity
by increasing the speed of the leg and/or arm movements.

STAMINA® UX2 Air Bike has been designed to allow the

Full Body Workout: Sitting comfortably erect, use the handlebars to either push or pull while simultaneously

pedaling. Alternate the effort to your arms or legs to intensify or reduce the work of the upper or lower body.
The handlebars may be gripped from underneath (palm up) to change the muscle groups used in the arms.

Lower Body Workout: Simply release the handlebars and place your hands on your hips or thighs as

you pedal. This concentrates the exercise on the lower body.

Upper Body Workout: Stand with feet on the Rear Stabilizer, lean over the seat and activate the fan

using the handlebars. This exercise is most effective when the muscles of the torso are used in a twisting
motion.

Advantages:

1. For the Upper Body:
Handlebar Push: Provides cardiovascular conditioning, triceps, upper back, and shoulder muscle training.
Handlebar Pull: Provides cardiovascular conditioning, biceps, shoulder, and chest muscle training.

2. For the Lower Body:
Pedaling: Provides cardiovascular conditioning, thigh and calf muscle toning, and hip, knee, and ankle

exion.

STORAGE

1. To store the STAMINA® UX2 Air Bike, simply keep it in a clean dry place.

2. The STAMINA® UX2 Air Bike is approximately 42.5 inches long (max.) x 22.3 inches wide x 45.3 inches

tall. These dimensions will vary. Please measure your STAMINA® UX2 Air Bike if exact dimensions are

needed.

3. The STAMINA® UX2 Air Bike must be lifted for movement. Two people are required.

4. To avoid damage to the electronics, remove the batteries before storing the STAMINA® UX2 Air Bike

for one year or more.

14

MAINTENANCE

The safety and integrity designed into the STAMINA® UX2 Air Bike can only be maintained when the
STAMINA® UX2 Air Bike is regularly examined for damage and wear. Special attention should be given

to the following:

1. Adjust the TENSION KNOB(27) and verify that it functions properly and the resistance changes.

2. Use a wrench to verify that the PEDALS(31, 32) are tightened securely. If tightening is required,

tighten the pedals rst, then tighten the THIN NUTS(35) securely.

3. Verify that all nuts and bolts are present and properly tightened. Replace missing nuts and bolts.

Tighten loose nuts and bolts.

4. Verify that the WARNING LABEL(73) is in place and easy to read. Call Stamina Products immediately

at 1-800-375-7520 for a replacement WARNING LABEL(73) if it is missing or damaged.

5. It is the sole responsibility of the user/owner to ensure that regular maintenance is performed.

6. Worn or damaged components shall be replaced immediately or the STAMINA® UX2 Air Bike

removed from service until repair is made.

7. Only Stamina Products supplied components shall be used to maintain/repair the STAMINA® UX2 Air

Bike.

8. Keep your STAMINA® UX2 Air Bike clean by wiping it off with an absorbent cloth after use.

IT IS NOT NECESSARY TO RETURN ENTIRE BIKE FOR A MONITOR REPAIR.

THE MONITOR IS REMOVABLE FROM BIKE FOR REPAIR OR REPLACEMENT.

PROBLEM CORRECTION

No speed or distance displays

2.
on meter.

Chain makes popping noise.3.

4.

5.

TROUBLE SHOOTING GUIDE

CAUSE

Batteries weak or dead.1.No display on meter.1.

Pickup wire not connected to

1.
meter.

Speed pickup not working

2.
properly.

Meter not working properly.3.

Chain is too loose.1.

1. 1.

Bike is not level.1.Bike rocks as you pedal. Adjust leveling caps on front

Replace batteries. (Use two AA.)1.

Securely plug pickup wire into

1.
the connecting wire on the meter.

Replace speed pickup.

2.

Replace meter.

3.

Adjust chain - See page 16 chain

1.
adjustment.

Adjust chainChain is too loose and hits fan.Bike makes sudden loud noise.

1.
stabilizer until bike is level.

Fan needs adjustment.1.Resistance too high.6. Adjust fan per instructions on

15

1.
page 16 and 17.

ADJUSTMENT INSTRUCTIONS

Chain Adjustment

Chain Adjustment required if the Chain is too loose.

1. Loosen the NUTS(3/8”-26)(66) on both sides of the fan.

2. Adjust the NUT(M6x1)(65) on the chain side of bike to remove
all slack from the chain.

3. Adjust the NUT(M6x1)(65) on the side opposite the chain so
that the center of the NUT(3/8”-26)(66) is the same distance
from TAB on both sides of bike.

4. Tighten the NUTS(3/8”-26)(66) on both sides of the fan.

TAB

Fan Adjustment

Fan Adjustment is required if the fan locks up or the resistance of the fan increases after use. To
adjust the fan, use the following procedures:

STEP 1: Remove both PEDALS(31, 32).
STEP 2: Remove the SCREWS(52, 54, & 55) holding the CHAIN GUARDS(29, 30) and FAN CAGES(28)

to the BIKE. Remove the CHAIN GUARDS(29, 30).
NOTE: The CRANK(10) should be pointing down.
STEP 3: Remove the NUTS(3/8”-26)(66), EYE BOLTS(22), and NUT(M6x1)(65) from the FAN AXLE(21).
STEP 4: Slide the FAN(18) toward the rear and slide the CHAIN(17) off of the big sprocket on the

CRANK(10). Then slide the CHAIN(17) off of the small sprocket on the FAN(18).
STEP 5: Unhook the TENSION STRAP(25) from the FRAME(1). Remove the FAN(18) and FAN CAGES

(28) from the bike.

HINT

It is best to lift the front of the frame and remove the fan and fan cages thru the bottom of the bike.

:

Left Side View

Small Sprocket

16

ADJUSTMENT INSTRUCTIONS

STEP 6: Hold the FAN(18) so that the FRONT SPROCKET is on your left side as shown.

STEP 7: Loosen NUTS “A” and “B” until at least 1/2” of FAN AXLE is showing between NUT “A” and

the FAN BUSHING.

STEP 8: Tighten NUT “C” completely until it bottoms out on the last FAN AXLE thread.

STEP 9: Tighten NUT “A” completely against FAN BUSHING, then back off 1/4 turn or until the FAN

AXLE has a very small amount of play side to side.

STEP 10: Hold NUT “A” and tighten NUT “B” completely against the SPEED PICKUP and NUT “A”.

NOTE: The FAN should be able to spin freely on the FAN AXLE after completion of this step.

FAN

FAN BUSHING

WASHER

FAN AXLE

NUT C

WAVY WASHER

FRONT

SPROCKET

STEP 11: Reverse STEPS 1 through 4 to reinstall the FAN(18),

FAN CAGES(28), CHAIN(17), and CHAIN GUARDS
(29, 30).

NOTE: DO NOT tighten NUTS(3/8”-26)(66) and NUTS

(M6x1)(65) until STEP 11.

NUT A

SPEED PICKUP

NUT B

WASHER

FAN BUSHING

RESISTANCE HUB

STEP 12: The CHAIN must be adjusted as follows:

a. Make sure the CHAIN(17) is on both the FRONT and

REAR SPROCKETS.

b. Tighten NUT(M6x1)(65) on EYE BOLTS(22) until all

slack is removed from CHAIN(17) and CENTER of
NUTS(3/8”)(66) are the same distance from TAB on
both sides of BIKE.

c. Tighten NUTS(3/8”)(66).

TAB

17

CONDITIONING GUIDELINES

How you begin your exercise program depends on your physical condition. If you have been inactive for
several years or are severely overweight, start slowly and increase your workout time gradually. Increase
your workout intensity gradually by monitoring your heart rate while you exercise.

Remember to follow these essentials:

Have your doctor review your training and diet programs.
Begin your training program slowly with realistic goals that have been set by you and your physician.
Warm up before you exercise and cool down after you work out.
Take your pulse periodically during your workout and strive to stay within a range of 60% (lower

intensity) to 90% (higher intensity) of your maximum heart rate zone. Start at the lower intensity, and

build up to higher intensity as you become more aerobically t.

If you feel dizzy or lightheaded you should slow down or stop exercising.

Initially you may only be able to exercise within your target zone for a few minutes; however, your aerobic
capacity will improve over the next six to eight weeks. It is important to pace yourself while you exercise
so you don't tire too quickly.

To determine if you are working out at the correct intensity, use a heart rate monitor or use the table
below. For effective aerobic exercise, your heart rate should be maintained at a level between 60%
and 90% of your maximum heart rate. If just starting an exercise program, work out at the low end of
your target heart rate zone. As your aerobic capacity improves, gradually increase the intensity of your
workout by increasing your heart rate.

Measure your heart rate periodically during your workout by stopping the
exercise but continuing to move your legs or walk around. Place two or

three ngers on your wrist and take a six second heartbeat count. Multiply
the results by ten to nd your heart rate. For example, if your six second

heartbeat count is 14, your heart rate is 140 beats per minute. A six second
count is used because your heart rate will drop rapidly when you stop
exercising. Adjust the intensity of your exercise until your heart rate is at the
proper level.

Target Heart Rate Zone Estimated by Age*

Age

20 years

25 years

30 years

35 years

40 years

45 years

50 years

55 years

60 years

65 years

70 years

Target Heart Rate Zone

(55%-90% of Maximum Heart Rate)

110-180 beats per minute

107-175 beats per minute

105-171 beats per minute

102-166 beats per minute

99-162 beats per minute

97-157 beats per minute

94-153 beats per minute

91-148 beats per minute

88-144 beats per minute

85-139 beats per minute

83-135 beats per minute

Average Maximum

Heart Rate 100%

200 beats per minute

195 beats per minute

190 beats per minute

185 beats per minute

180 beats per minute

175 beats per minute

170 beats per minute

165 beats per minute

160 beats per minute

155 beats per minute

150 beats per minute

wrist pulse

* For cardiorespiratory training benefits, the American College of Sports Medicine recommends

working out within a heart rate range of 55% to 90% of maximum heart rate. To predict the

maximum heart rate, the following formula was used: 220 - Age = predicted maximum heart rate

18

WARM-UP and COOL-DOWN

Warm-Up

Warm up for two to ve minutes before strength training or aerobic exercising. Perform activities that

raise your heart rate and warm the working muscles. Activities may include brisk walking, jogging,
jumping jacks, jump rope, and running in place.

Stretching

strength or aerobic training session is very important. Muscles stretch more easily at these times
because of their elevated temperature, which greatly reduces the risk of injury. Stretches should be held
for 15 to 30 seconds. Do not bounce.

The purpose of warming up is to prepare your body for exercise and to minimize injuries.

Stretching while your muscles are warm after a proper warm-up and again after your

Suggested Stretching Exercises

Lower Body Stretch

Place feet shoulder-width

apart and lean forward.
Keep this position for 30
seconds using the body as a
natural weight to stretch the
backs of the legs.

DO NOT BOUNCE!

When the pull on the back of
the legs lessens, gradually
try a lower position.

Floor Stretch

While sitting on the oor,

open the legs as wide as
possible. Stretch the upper
body toward the knee on the
right leg by using your arms
to pull your chest to your
thighs. Hold this stretch 10
to 30 seconds.

DO NOT BOUNCE!

Do this stretch 10 times.
Repeat the stretch with the
left leg.

Bent Torso Pulls

While sitting on the oor,

have legs apart, one leg
straight and one knee bent.
Pull the chest down to touch
the thigh on the leg that is
bent, and twist at the waist.
Hold this position at least 10
seconds. Repeat 10 times
on each side.

Bent Over Leg Stretch

Stand with feet shoulder-

width apart and lean forward

as illustrated. Using the

arms, gently pull the upper
body towards the right leg.
Let the head hang down.

DO NOT BOUNCE!

Hold the position a minimum
of 10 seconds. Repeat
pulling the upper body to
the left leg. Do this stretch
several times slowly.

Remember to always check with your physician before starting any exercise program.

Cool-Down

state at the end of each exercise session. A proper cool-down slowly lowers your heart rate and allows
blood to return to the heart. Your cool-down should include the stretches listed above and should be

completed after each strength training session.

The purpose of cooling down is to return the body to its normal, or near normal, resting

19

FRONT

PRODUCT PARTS DRAWING

BACK

20

PARTS LIST

1 Main Frame 1
2 Rear Stabilizer 1
3 Front Stabilizer 1
4 Seat Post 1
6 Left Handlebar 1
7 Right Handlebar 1
8 Lower Bar 2
9 Left Linkage 1
10 Crank and Sprocket 1
11 Wavy Washer 1
12 Small Keyed Washer 2
13 Split Bearing 4
14 Crank Bearing Retainer 2
15 Large Keyed Washer 1
16 Roll Pin 1
17 Chain (1/4” pitch) 1
18 Fan 1
19 Resistance Hub 1
20 Fan Bushing 2
21 Fan Axle 1
22 Eye Bolt (M6 x 1 x 55mm) 2
23 Speed Pickup 1
24 Tension Spring 1
25 Tension Strap 1
26 Hook 1
27 Tension Knob 1
28 Fan Cage 2
29 Left Chain Guard 1
30 Right Chain Guard 1
31 Left Pedal w/ Long Shaft 1
32 Right Pedal w/ Long Shaft 1
33 Pedal Washer (1/2”) 2
34 Spacer 2

35 Thin Nut (1/2”-20) 2

36 Axle 1
37 Bushing 6
38 Bushing Washer (ø16.3 x ø25mm x 0.5mm) 2
39 Large Washer (M8) 2
40 Nut Cap 2
41 Foam Grip 2
42 Linkage Bushing 2
43 Seat 1
44 Sleeve 1
46 Locking Knob 1
47 Meter 1
48 Leveling Cap (28.6mm) 2
49 Endcap (45mm) 2

PART# PART NAME QTY

21

PARTS LIST

50 Round Plug (25mm) 2
51 Carriage Bolt (M8 x 1.25 x 38mm) 2
52 Screw, Round Head (M4 x 15mm) 4
54 Screw, Round Head (M5 x 15mm) 4
55 Screw, Round Head (M5 x 25mm) 11
56 Screw, Round Head (M5 x 75mm) 4
57 Screw, Round Head (M5 x 0.8 x 12mm) 4
58 Screw, Flat Head (M5 x 0.8 x 15mm) 1
59 Bolt, Round Head (M6 x 1 x 12mm) 4
60 Bolt, Round Head (M6 x 1 x 25mm) 4
61 Bolt, Hex Head (M8 x 1.25 x 45mm) 2
62 Nylock Nut (M8 x 1.25) 7
63 Nylock Nut (M6 x 1) 4
64 Acorn Nut (M8 x 1.25) 2
65 Nut (M6 x 1) 2

66 Nut (3/8” - 26) 5

67 Washer (M8 x ø16mm x 1.5mm) 3
68 Washer (M8 x ø22mm x 1.5mm) 2
69 Washer (3/8”) 3
70 Arc Washer (M6) 4
71 Arc Washer (M8) 4
72 Wavy Washer (M10) 1
73 Warning Label 1
74 Wrench 1

75 Multi-opening Wrench 1

76 Allen Wrench 1
77 Manual 1

PART# PART NAME QTY

22

LIMITED WARRANTY

MODEL 15-0881

WARRANTY

Stamina Products, Inc. warrants that this product will be free from defects in materials and workmanship
under normal use, service, proper assembly and proper operation for a period of 90 days on the
parts and one year on the frame from the date of the original purchase from an authorized retailer.

THIS WARRANTY SHALL NOT APPLY TO ANY PRODUCT WHICH HAS BEEN SUBJECT
TO COMMERCIAL USE, ABUSE, MISUSE, ALTERATION OF ANY TYPE OR CAUSE OR TO
ANY DEFECT OR DAMAGE CAUSED BY IMPROPER ASSEMBLY, REPAIR, REPLACEMENT,
SUBSTITUTION OR USE WITH PARTS OTHER THAN PARTS PROVIDED BY STAMINA PRODUCTS,
INC. Commercial use includes use of the product in athletic clubs, health clubs, spas, gymnasiums,

exercise facilities, and other public or semipublic facilities whether or not the product's use is in

furtherance of a prot making enterprise, and all other use which is not for personal, family, or household

purposes.

To implement this limited warranty, send a written notice stating your name, date, and place of purchase
and a brief description of the defect along with your receipt to Stamina Products, Inc. P.O. Box 1071,
Springeld Missouri, USA, 65801-1071, or email us at [e-mail], or
call us at 1-800-375-7520. If the defect is covered under this limited warranty, you will be requested to
return the product or part to us for free repair or replacement at our option. NO ACTION FOR BREACH

OF THIS LIMITED WARRANTY MAY BE COMMENCED MORE THAN ONE (1) YEAR AFTER THE
DATE THE ALLEGED BREACH WAS OR SHOULD HAVE BEEN DISCOVERED. NO ACTION FOR
BREACH OF ANY IMPLIED WARRANTY MAY BE COMMENCED MORE THAN ONE (1) YEAR AFTER
DELIVERY OF THE PRODUCT TO THE PURCHASER. This limited warranty is not transferable. IF
ANY PART OF THE PRODUCT IS NOT IN COMPLIANCE WITH THIS LIMITED WARRANTY OR ANY
IMPLIED WARRANTY, THE REMEDY OF REPAIR OR REPLACEMENT IS THE EXCLUSIVE REMEDY
AVAILABLE TO YOU. In the event that the purchaser makes any claim under this limited warranty or any

implied warranty, the Warrantor reserves the right to require the product to be returned for inspection,

at the purchaser's expense, to the Warrantor's premises in Springeld, Missouri. Return of the enclosed

warranty registration card is not required for warranty coverage, but is merely a way of establishing the
date and place of purchase.

Stamina Products, Inc. SHALL NOT BE LIABLE FOR THE LOSS OF USE OF ANY PRODUCT, LOSS

OF TIME, INCONVENIENCE, COMMERCIAL LOSS OR ANY OTHER INDIRECT, CONSEQUENTIAL,
SPECIAL OR INCIDENTAL DAMAGES DUE TO BREACH OF THE ABOVE WARRANTY OR ANY
IMPLIED WARRANTY.

This limited warranty is the only written or express warranty given by Stamina Products, Inc. This

warranty gives you specic legal rights, and you may also have other legal rights which vary from state

to state. ANY OTHER RIGHT WHICH YOU MAY HAVE, INCLUDING ANY IMPLIED WARRANTY OR
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, IS LIMITED IN DURATION TO
THE DURATION OF THIS WARRANTY.

The laws in some jurisdictions restrict the rights of manufacturers and distributors of consumer goods
to disclaim or limit implied warranties and consequential and incidental damages with respect thereto.
If any such law is found to be applicable, the foregoing disclaimers and limitations of and on implied
warranties and consequential and incidental damages with respect thereto shall be disregarded and shall
be deemed not to have been made to the extent necessary to comply with such legal restriction.

23

NOTES

24

NOTES

25

TO CONTACT CUSTOMER SERVICE

TO CONTACT CUSTOMER SERVICE

For your convenience, Stamina’s customer service representatives can be reached by email at customerservice@
staminaproducts.com or by phone at 1-800-375-7520 (in the U.S.). Our customer service representatives are available Monday

through Thursday from 7:30 a.m. until 5:00 p.m., and Friday 8:00 a.m. until 3 p.m. Central Time.

ONLINE

CUSTOMER SERVICE

[e-mail]

www.staminaproducts.com

TELEPHONE

CUSTOMER SERVICE

Tel: [phone]

FAX

CUSTOMER SERVICE

Fax: [phone]

STAMINA PRODUCTS, INC.

P.O. Box 1071 Springeld, MO. 65801-1071

MAIL

ATTN: Customer Service

Would you like to recieve email information or special offers from Stamina Products? Register at contact.staminaproducts.com

TO REGISTER YOUR PRODUCT

TO REGISTER YOUR PRODUCT

To enact your warranty, please register your product by going to register.staminaproducts.com. Please have your product model
number (printed on the cover of this owner’s manual) and the serial number (printed on the black and white sticker on your
product) ready.

If you don’t have internet access, you can call customer service at 1-800-375-7520, or ll out and mail the product registration
form below to Stamina Products, Inc.; P.O. Box 1071; Springeld, MO 65801-1071.

PRODUCT REGISTRATION FORM

Model Number: ...................................................................................... Serial Number: .............................................................................................

Product Name: ..................................................................................................................................................................................................................................

Place Purchased: ..............................................................................................................................................................................................................................

Date of Purchase: .................................................................................. Purchase Price: ............................................................................................

First Name: ............................................................................................ Last Name: ...................................................................................................

City: .................................................................. State: ................................................................ Zip Code: .................................................

Email Address: ....................................................................................... Phone #: ( ) ......................................................................................

Would you like to receive email information or special offers from Stamina Products?* ____Yes ____No

Stamina Products, Inc.

P.O. Box 1071

Springeld, MO 65801-1071

*If yes, be sure your email address is included above.

Detach and Mail or Fax the Form Above

TO ORDER PARTS

TO ORDER PARTS

If there are missing or damaged parts, you can go to parts.staminaproducts.com and order those parts. If you have questions,
please contact customer service. Do not return the product. To order parts by mail, fill out the sheet below and fax it to

417-889-8064. The part will be mailed to your address.

Detach and Mail or Fax the Form Below

PARTS ORDER FORM

Mr./Ms: ..............................................................................................................................................................................................................................................

Address: ........................................ ............................................................................................. Apt. #:..........................................................................

City: .................................................................. State: ................................................................ Zip Code: .................................................

IMPORTANT : We must have your phone number to process the order!

Phone #: ( ) ................................................................................ Work Phone #: ( ) .............................................................................

Date of Purchase: ..................................................................................

Model #: ............................................................................................................................................................................................................................................

Purchased From: ..............................................................................................................................................................................................................................

IMPORTANT : Before lling out the form below make sure you have the correct information.

PART # DESCRIPTION QUANTITY

EXAMPLE:

1 Rear Unit Assembly 1

Refer to the parts list to make sure you're ordering the right parts!

Stamina Products, Inc.

P.O. Box 1071

Springeld, MO 65801-1071