Stamina T3000 Treadmill 45-1003, In Motion T3000 Owner's Manual

45-1003

STAMINA PRODUCTS

MADE IN CHINA

Product May Vary Slightly

From Pictured.

Exercise can present a health
risk. Consult a physician
before beginning any exercise
program with this equipment.
If you feel faint or dizzy,
immediately discontinue use
of this equipment. Serious
bodily injury can occur if this
equipment is not assembled
and used correctly. Serious
bodily injury can also occur if
all instructions are not
followed. Keep others and
pets away from equipment
when in use. Always make
sure all bolts and nuts are
tightened prior to each use.
Follow all safety instructions in
this manual.

When calling for parts or
service, please specify the
following number.

WA RNING

CAUTION:
Weight on this product should not exceed 250 lbs.

Owner's Manual

2040 N. Alliance, Springfield, MO 65803

Customer Service

1 [phone]

www.staminaproducts.com

This Product is Produced Exclusively by

2008, 06

2008 Stamina Products, Inc.

TABLE OF CONTENTS

SAFETY INSTRUCTIONS

To reduce the risk of serious injury, read the following Safety Instructions before
using the INMOTION

T3000 T readmill.

WARNING:

Before starting any exercise or conditioning program you should consult with your personal
physicia n to see if you require a complete physical exa m. This is e specially i mporta nt if you
are over the age of 35, have never exercised before, are pregnant, or suffer from any
illness. READ AND FOLLOW THE SAFETY PRECAUTIONS. FAILURE TO FOLLOW

THESE INSTRUCTIONS CAN RESUL T IN SERIOUS BODILY INJURY.

WARNING:

2

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

11.

12.

13.

14.

15.

16.

17.

18.

Read all warnings posted on the INMOTION

T3000 Treadmill.

Read this Owner's Manual and follow it carefully before using the INMOTION

T3000 Treadmill.

Make sure that it is properly assembled and tightened before use.
We recommend that two people be available for assembly of this product.
Keep children away from the INMOTION

T3000 Tre admill. Do not allow children to use or play on

the INMOTION

T3000 Treadmill. Keep children and pets away from the INMOTION T3000

Treadmill when it is in use.

It is recommended that you place this exercise equipment on an equipment mat.
Set up and operate the INMOTION

T3000 Treadmill on a solid level surface. Do not position the

INMOTION

T3000 Treadmill on loose rugs or uneven surfa ces.

Inspect the INMOTION

T3000 Treadmill for worn or loose components prior to use. Tighten/

replace any loose or worn components prior to using the INMOTION T3000 Tre admill.
Keep fingers clear of all pinch points when folding a nd unfolding the INMOTION

T3000 Tre admill.

When folding the INMOTION

T3000 Tre admill for storage, ma ke sure that Base Fra me Assembly

is locked securely in the folded position by the Pull Pin(6).
Consult a physician prior to commencing an exercise program. If, at any time during exercise, you
feel faint, dizzy, or experience pain, stop and consult your physician.
Follow your physician's recommendations in developing your own personal fitness program.
Always choose the workout which best fits your physical strength and flexibility level. Know your
limits and train within them. Always use common sense when exercising.
Do not wear loose or dangling clothing while using the INMOTION

T3000 Treadmill.

Never exercise in bare feet or socks; always wear correct footwear, such as running, walking, or
crosstraining shoes. Be sure that they fit well, provide foot support a nd feature non-s kid rubber soles.
Be careful to maintain your balance while using, mounting, dismounting, or assembling the

INMOTION

T3000 Treadmill, loss of balance may result in a fall and serious bodily injury.

The INMOTION

T3000 Treadmill should not be used by persons weighing over 250 pounds.

The INMOTION

T3000 Treadmill should be used by only one person at a time.

The INMOTION

T3000 Tre a dmill is for consumer use only. It is not for use in public or semipublic

facilities.

Safety Instruction s 2
Before You Begin 4
Equipment Warning & Notice Labels 5
Hardware Identification Chart 6
Assembly Instructions 7
Using The Electronics Meter 10
Treadmill Adjustments 11

Maintenance 12
Storage 13
Product Parts Drawing 14
Parts List 15
Warranty 16
Notes 17
Fax/Mail Ordering Form 18

Page Page

THANK YOU FOR PURCHASING THE

INMOTION T3000 TREADMILL

To help you get started, we have pre-assembled most of your
INMOTION T3000 Treadmill at the factory with the exception

of those few parts left unassembled for shipping purposes.

Simply follow the few assembly instructions set forth in this manual.

With regular workouts you will be getting your body into sha pe

and on your way to achieving a happier and healthier lifestyle.

3

Should you have any que stions,

please call our Customer Service Department toll-free number,

1 [phone]

Monday - Thursday, 7:30 A.M. - 5:00 P.M., Central Time.

Friday, 8:00 A.M. - 3:00 P.M., Central Time.

CALL US FIRST

Customer Service

1(800) 375-7520

www.staminaproducts.com

TELEPHONE

CUSTOMER SERVICE

Tel: [phone]

FAX

CUSTOMER SERVICE

Fax: [phone]

MAIL

STAMINA PRODUCTS, INC.

ATTN: Customer Service

P.O. Box 1071

Springfield, MO. 65801-1071

ONLINE

CUSTOMER SERVICE

[e-mail]

[e-mail]

www.staminaproducts.com

BEFORE YOU BEGIN

4

THE FOLLOWING TOOLS ARE REQUIRED FOR ASSEMBLY : Wrench

Allen Wrench (4mm)

Meter

Right Upright

Moving Wheel

Upright Support

Side Molding

Walking Belt

Base Frame

U-Shaped Handrail

Left Upright

Flywheel

Adjustment
Bracket

Bumper Stand

Thank you for choosing the INMOTION

T3000

Treadmill

. We take great pride in producing this

quality product and hope it will provide many hours
of quality exercise to make you feel better , look better
and enjoy life to its fullest.
Yes, it's a proven fact that a regular exercise
program can improve your physical and mental
health. Too often, our busy lifestyles limit our time
and opportunity to exercise. The INMOTION

T3000

Treadmill

provides a convenient and si mple method

to begin your assault on getting your body in shape
and achieving a happier and healthier lifestyle.
Before reading further, please review the drawing
below and fa mili arize yoursel f with the parts that are
labeled.
Read this manual carefully before using the

INMOTION T3000 Treadmill.

Although Stamin a constructs its products with the
finest materials and uses the highest standards of
manufacturing and quality control, there can
sometimes be missing parts or incorrectly sized
parts. If you have any questions or problems with
the parts included with your INMOTION

T3000

Treadmill

, plea se do not return the product. Contact

us FIRST!
If a part is missing or defective, please call us toll
free at 1-800-375-7520 (in the U.S.). Our Customer
Service Staff is available to a ssist you from 7:30 A.M.
to 5:00 P .M. (Central T ime) Monday through Thursday
and 8:00 A.M. to 3:00 P.M. (Central Ti me) on Friday.
If you would like to contact us online, go to our
website at www.sta mina products.com a nd a ccess the
Customer Service section.
Be sure to have the name and model number of
the product available when you contact us.

Warning Label

5

EQUIPMENT WARNING & NOTICE LABELS

This chart is provided to help identify the warning & notice labels on the INMOTION T3000 Treadmill.
Please take a moment to familiarize yourself with all of the warning & notice labels.

Label is larger tha n actual size

WAR NING LABEL(46)

W1

6

Part No. and Description Qty

35 Bolt, Hex Head (M12x1.75x75mm) 2

36 Bolt, Button Head (M6x1x15mm) 2

45 Washer (M12) 2

41 Arc Washer (M6) 2
42 Arc Washer (M8) 4

HARDWARE IDENTIFICATION CHART

This chart is provided to help identify the hardware used in the assembly process. Place the washers, the
ends of the bolts, or screws on the circles to check for the correct di a meter . Use the small scale to check the
length of the bolts and screws.

NOTICE: The length of all bolts and screws except those with flat hea ds is

measured from below the head to the end of the bolt or screw.
Flat head bolts and screws are measured from the top of the
head to the end of the bolt or screw.

mm.

in.

INCHES

MILLIMETERS

11/2021/2 31/2 41/2 51/2 61/2

0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150

6 8 10 12

3/16" 5/16" 1/2"3/8"1/4"

length

length

After unpacking the unit, open the hardware bag and make sure that you have all the following items.
Some hardware may be already attached to the part.

34 Bolt, Hex Head (M8x1.25x15mm) 4

Place all parts from the box in a cleared area and position them on the floor in front of you. Remove all
packing materi als from your area a nd pla ce the m ba ck into the box. Do not dispose of the pa cking materi als
until a ssembly is completed. Read e a ch step carefully before beginning. If you are missing a part please call
our toll-free number for assistance 1 [phone] or e-mail us at:

[e-mail]

7

ASSEMBLY INSTRUCTIONS

STEP 1

NOTE: The LEFT UPRIGHT(2) is the one with the LOWER EXTENSION WIRE(27).
Attach the LEFT and RIGHT UPRIGHTS(2, 3) to the UPRIGHT SUPPORT(4) with HEX BOLTS
(M8x1.25x15mm)(34) and ARC W ASHERS(M8)(42).

ASSEMBLY INSTRUCTIONS

8

STEP 2

Place the BASE FRAME(1) between the LEFT and RIGHT UPRIGHTS(2, 3) and secure with HEX
BOLTS(M12x1.75x75mm)(35) and W ASHERS(M12)(45). DO NOT TIGHTEN COMPLETELY.

STEP 3

Slide down the upper parts of the FOAM GRIPS(22), so you can see the screw hole s at the ba ck side of the
tops of the LEFT and RIGHT UPRIGHTS(2, 3). Conne ct the UPPER EXTENSION WIRE(26) to the LOWER
EXTENSION WIRE(27). Insert the U-SHAPED HANDRAIL(5) into the LEFT and RIGHT UPRIGHTS(2, 3)
and secure with BUTTON HEAD BOLTS(M6x1x15mm)(36) and ARC WASHERS(M6)(41). Slide up the

FOAM GRIPS(22) to cover the screw hea ds.

STEP 4

Go back and tighten HEX BOLTS(M12x1.75x75mm)(35) in STEP 2. Connect the LOWER EXTENSION
WIRE(27) located on the LEFT UPRIGHT(2) to the SENSOR WIRE(28). Insert the PULL PIN(6) through
the RIGHT UPRIGHT(3) and BASE FRAME(1) to lock the BASE FRAME(1) in position.

Slide down the
upper parts of the
FOAM GRIPS(22)
for assembly.

ASSEMBLY INSTRUCTIONS

9

STEP 5

Install two AA batteries into the METER(24), two batteries included. See page 10 f or detailed battery installation
instructions. Slide the METER(24) onto the plate on the U-SHAPED HANDRAIL(5). Connect the UPPER

EXTENSION WIRE(26) to the METER(24).

STEP 6

Attach the BUMPER STANDS(20) to the bottom of the BASE FRAME(1).
NOTE: The BUMPER STANDS(20) may be stored on the end of the BASE FRAME(1) to increase the

angle of the treadmill and reduce the walking resistance. See page 12 for details on adjusting the walking
resistance.

USING THE ELECTRONIC METER

Walking Belt movement or push the button.
Automatic shut off after 4 minutes of ina ctivity .

POWER OFF :

POWER ON :

AA Batteries

MODE / CLEAR BUTTON:

Press and release to select functions.
Press and hold for three se conds to reset all
functions to zero.

SCAN:

TIME:

SPEED:

DISTANCE:

CALORIES:

Automatically scans TIME, SPEED, DISTANCE, and CALORIES in sequence with a change
every four seconds. Press a nd release the button until "

" a ppears on the display and points

to SCAN.
Displays the time from 1 sec. up to 99:59 minutes.
Displays the current speed from zero to 999.9 Mile/Hr.
Displays the distance from zero to 99.99 miles.
Displays the calorie consumption, from zero to 999.9 Kcal.

The calorie readout is a n estimate for a n average user . It should be used only a s a comparison
between workouts on this unit.

HOW TO INSTALL AND REPLACE BATTERY:

Open the Battery Door on the back of the meter.
The meter operates with two AA batteries, two batteries included.
Refer to the illustration to install or replace the batteries.

1.

2.

Do not mix a new battery with an old battery.
Use the same type of battery. Do not mix an alkaline battery with
another type of battery.
Rechargeable batteries are not recommended.

1.

2.

3.

NOTE:

FUNCTIONS:

10

The ba sic idea behind the ma nual treadmill is to have the belt running on a tre admill board a nd between two
rollers so that the belt will move without much effort. In order for the belt to run smoothly, there are a few
points that need to be noted.

TREADMILL ADJUSTMENTS

BELT ALIGNMENT

The belt must be in the center of the treadmill to prevent it from rubbing against the flywheels. If the belt rubs
a flywheel, it will be difficult to keep the belt moving and eventually da mage the edge of the belt.

The treadmill has belt guides welded to the bottom of the treadmill frame that move the belt toward the
center of the treadmill. However, the rear roller must be properly aligned with the treadmill frame and front
roller if the belt is to remain centered on the treadmill.

The bolts in the rear of the treadmill (one on the left and the other on the right) adjust the alignment of the
rear roller as well as the tension of the belt.

The belt will run to the side of the loose rear bolt.
Hint:

BEL T DRIFTING LEFT

Turn the left screw 1/4 turn CLOCKWISE and the right screw 1/4 turn
COUNTER-CLOCKWISE, then walk on the treadmill. Repeat if needed.

BEL T DRIFTING RIGHT

Turn the left screw 1/4 turn COUNTER-CLOCKWISE and the right screw
1/4 turn CLOCKWISE, then walk on the tre admill. Repeat if needed.

NOTE:

When you believe the WALKING BELT is centered, use the treadmill for three (3) minutes to verify the
WALKING BELT won't drift to one side. If the WALKING BEL T continues to drift, the floor may not be level.

Rotate the treadmill 90 degrees or move the treadmill to another location.

BELT TENSION

The belt should be tight and not lying on the treadmill board. If the belt is too loose, the belt will slip on the
front roller and you will notice a jerky movement when you walk on the treadmill. If the belt is too tight, the
edges of the belt will begin to curl and more effort will be required to move the belt. Excessive belt tension
can also damage the bearings in the rollers. The bolts in the rear of the treadmill (one on the left and the
other on the right) adjust the tension of the belt as well as the alignment of the rear roller.

BELT TOO LOOSE: Use the 4mm ALLEN WRENCH to tighten the bolts in the rear of the treadmill.

Tighten both rollers 1/4 turn at a time until the belt stops slipping on the front roller.

BEL T TOO TIGHT: Use the 4mm ALLEN WRENCH to loosen the bolts in the rear of the treadmill. Loosen

both rollers 1/2 turn at a time until the belt begins to slip on the front roller. Then use the procedure above to
tighten the belt.

11

Eyeball the rear roller to make sure both the right side and the left side of the roller are the same
distance from the back edge of the treadmill. Use the 4mm ALLEN WRENCH to make these
adjustments. Turn the bolts Clockwise to tighten and Counter-Clockwise to loosen.

RIGHT

ADJUSTMENT

LEFT

ADJUSTMENT

TREADMILL ADJUSTMENTS
WALKING RESISTANCE

The walking resistance or effort needed to push the treadmill belt can be adjusted by changing the incline
angle. This treadmill has two adjustment positions.

Lowest Re sis tance

Remove (unscrew) the BUMPER STANDS(20)
from the bottom of the treadmill and store them

in the end of the treadmill.

Highest Resistance

The BUMPER STANDS(20) are attached to

the bottom of the treadmill.

Since this is a new machine, you may need some time to get used to walking on the treadmill and to
break it in.
If the walking resistance is still too high, check the BELT TENSION.
The belt resistance can be reduced by adding silicone lubricant between the belt and the board. Wipe
the board under the belt with a cloth and spray or spread silicone lubricant on the board under the belt.

Clean the exposed surfaces of the walking belt and the board with an absorbent cloth.
It is the sole responsibility of the user/owner to ensure that regular maintenance is performed.
Verify that all nuts a nd bolts are pre sent and properly tightened. Re pla ce missing nuts a nd bolts. T ighten
loose nuts and bolts.
Verify that the Warning Label is in place and easy to read. Call Stamina Products immediately
(1-800-375-7520) for a replacement W arning Label if the Warning Label is missing or damaged.
Worn or damaged components shall be replaced immediately or the INMOTION

T3000 Treadmill

removed from service until repair is made.
Only Stamina Products supplied components shall be used to maintain/repair the INMOTION

T3000

Treadmill

.

Keep your INMOTION

T3000 Treadmill clean by wiping with an absorbent cloth after use.

If the WALKING BEL T(15) does not move ea sily , lubricate the BOARD(16) under the WALKING BEL T(15)
with Silicone Lubricant.

1.

2.

3.

4.

5.

6.

7.

8.

MAINTENANCE

The safety and integrity designed into the INMOTION T3000 T re a dmill ca n only be maintained when the
INMOTION T3000 Treadmill is regularly examined for damage and wear. Special attention should be

given to the following:

NOTE:

1.

2.

3.

12

STORAGE

13

To store the INMOTION

T3000 Treadmill simply keep it in a clean dry place.

To avoid damage to the electronics meter, remove the batteries before storing the INMOTION

T3000

Treadmill

for one year or more.

Follow the following process to fold The INMOTION

T3000 Treadmill as illustrated for easy storage.

1.

2.

3.

4.

UNFOLD THE INMOTION T3000 Treadmill

Remove the PULL PIN(6) from the BASE FRAME ASSEMBLY(1) and unfold the BASE FRAME
ASSEMBLY(1).
Lock the BASE FRAME ASSEMBLY(1) in position by inserting the PULL PIN(6) through the RIGHT
UPRIGHT FRAME(3) and BASE FRAME(1).

a.

b.

Move the INMOTION

T3000 Tre admill with the moving wheels on the UPRIGHT SUPPORT(4). Gra sp

the U-SHAPED HANDRAIL(5) to move the INMOTION

T3000 Tre admill.

a.b.Remove the PULL PIN(6) to unlock the BASE FRAME ASSEMBLY(1).

Fold up the BASE FRAME ASSEMBL Y(1). Insert the PULL PIN(6) into the hole in the BASE FRAME

ASSEMBLY(1) to lock the BASE FRAME ASSEMBLY(1) in upright position.
CAUTION: Make sure the BASE FRAME ASSEMBLY(1) is locked securely in folded position by the
PULL PIN(6).

PRODUCT PARTS DRAWING

14

FRONT

BACK

Belt Guides

PARTS LIST

DIAGRAM# PART NAME QTY

15

1 Base Frame 1
2 Left Upright 1
3 Right Upright 1
4 Upright Support 1
5 U-Shaped Handrail 1
6 Pull Pin 1
7 Bumper 1
8 Front Roller /w Flywheels 1
9 Front Shaft 1
10 Bearing (6000zz) 4
11 Plastic Spacer 4
12 Rear Roller 1
13 Rear Shaft 1
14 Adjustment Bracket 2
15 Walking Belt 1
16 Board 1
17 Left Side Molding 1
18 Right Side Molding 1
19 Round Cap (38mm) 2
20 Bumper Stand 2
21 Moving Wheel 2
22 Foam Grip 2
23 Long Foam Grip 2
24 Meter 1
25 Grommet Plug 2
26 Upper Extension Wire 1
27 Lower Extension Wire 1
28 Sensor Wire 1
29 Magnet 1
30 Screw Sleeve 6
31 Round Plug (31.8mm) 2
32 Screw , Round Head (M3 x 15mm) 2
33 Screw , Flat Head (M5 x 25mm) 6
34 Bolt, Hex Head (M8 x 1.25 x 15mm) 4
35 Bolt, Hex Head (M12 x 1.75 x 75mm) 2
36 Bolt, Button Head (M6 x 1 x 15mm) 2
37 Bolt, Button Head (M6 x 1 x 55mm) 2
38 Bolt, Button Head (M8 x 1.25 x 15mm) 2
39 Bolt, Socket Head (M6 x 1 x 70mm) 2
40 Nylock Nut (M6 x 1) 2
41 Arc Washer (M6) 2
42 Arc Washer (M8) 6
43 Washer (M6) 6
44 Washer (M10) 2
45 Washer (M12) 2
46 Warning Label 1
47 Wrench 1
48 Allen Wrench (4mm) 1
49 Owner's Ma nual 1

16

WARRANTY

LIMITED WARRANTY

MODEL 45-1003

Stamina Products, Inc. warrants that this product will be free from defects in materials and workmanship
under normal use, service and proper operation for a period of 90 days on the parts and one year on the
frame from the date of the original purchase from an authorized retailer. THIS WARRANTY SHALL NOT

APPLY TO ANY PRODUCT WHICH HAS BEEN SUBJECT TO COMMERCIAL USE, ABUSE, MISUSE,
ALTERATION OF ANY TYPE OR CAUSE OR TO ANY DEFECT OR DAMAGE CAUSED BY REPAIR,
REPLACEMENT , SUBSTITUTION OR USE WITH P ARTS OTHER THAN P ARTS PROVIDED BY ST AMINA
PRODUCTS, INC. Commercial use includes use of the product in athletic clubs, health clubs, spas,

gymnasiums, exercise facilities, and other public or semipublic facilities whether or not the product's use is
in furtherance of a profit making enterprise, and all other use which is not f or personal, family, or household
purposes.

T o i mplement this li mited warranty, send a written notice stating your name, date, a nd place of purchase and
a brief description of the defect along with your rece ipt to Stamin a Products, Inc. P .O. Box 1071, Springf ield

Missouri, USA, 65801-1071, or email us at [e-mail], or call us at
1 [phone]. If the defect is covered under this limited warranty, you will be requested to return the
product or part to us for free repair or replacement at our option. NO ACTION FOR BREACH OF THIS
LIMITED WARRANTY MAY BE COMMENCED MORE THAN ONE (1) YEAR AFTER THE DATE THE
ALLEGED BREACH WAS OR SHOULD HAVE BEEN DISCOVERED. NO ACTION FOR BREACH OF
ANY IMPLIED W ARRANTY MAY BE COMMENCED MORE THAN ONE (1) YEAR AFTER DELIVERY OF
THE PRODUCT TO THE PURCHASER. This limited warranty is not trans fera ble. IF ANY PART OF THE
PRODUCT IS NOT IN COMPLIANCE WITH THIS LIMITED W ARRANTY OR ANY IMPLIED W ARRANTY,
THE REMEDY OF REP AIR OR REPLACEMENT IS THE EXCLUSIVE REMEDY A V AILABLE TO YOU. In

the event that the purchaser ma kes a ny claim under this limited warra nty or any i mplied warranty , the W arrantor
reserves the right to require the product to be returned for inspection, at the purchaser's expense, to the
Warrantor's premises in Springfield, Missouri. Return of the enclosed warranty registration card is not
required for warranty coverage, but is merely a way of establishing the date and place of purchase.

Stamin a Products, Inc. SHALL NOT BE LIABLE FOR THE LOSS OF USE OF ANY PRODUCT, LOSS OF

TIME, INCONVENIENCE, COMMERCIAL LOSS OR ANY OTHER INDIRECT, CONSEQUENTIAL,
SPECIAL OR INCIDENT AL DAMAGES DUE TO BREACH OF THE ABOVE WARRANTY OR ANY IMPLIED
WARRANTY.

This limited warra nty is the only written or express warranty given by Sta mina Products, Inc. This warranty
gives you specific legal rights, and you may also have other legal rights which vary from state to state.

ANY OTHER RIGHT WHICH YOU MAY HAVE, INCLUDING ANY IMPLIED WARRANTY OR
MERCHANT ABILITY OR FIT NESS FOR A P ARTICULAR PURPOSE, IS LIMITED IN DURA TION TO THE
DURA TION OF THIS WARRANTY.

The laws in some jurisdictions restrict the rights of manufacturers and distributors of consumer goods to
disclaim or limit implied warranties and consequential and incidental damages with respect thereto. If any
such law is found to be a pplicable, the foregoing disclai mers and li mitations of a nd on implied warranties a nd
consequential a nd incidental da mages with respect thereto shall be disregarded a nd shall be deemed not to
have been made to the extent necessary to comply with such legal restriction.

17

NOTES

IMPORT ANT : Before filling out the form below make sure you have the right information.

Refer to the parts list to make sure you're ordering the right parts!

Detach and Mail or Fax the Form Below

Stamina Products, Inc.

P.O. Box 1071

Springfield, MO 65801-1071

IMPORT ANT : We must have your phone number in order to process the order!

FAX/MAIL ORDERING FORM

Please do not return the product. For your convenience, Stamina's Customer Service Department can be
reached by e mail at [e-mail] or toll free at 1-800-375-7520 (in the U.S.). Should a part
be missing or a defective part found, please call us from 7:30 A.M. to 5:00 P.M. Central Time, Monday
through Thursday and 8:00 A.M. to 3:00 P .M. on Friday or f ill out the fax sheet ordering f orm below and fax
it to [phone]. Our Customer Service Department will be a ble to a ssist you with your problem a nd the
part will be mailed directly to your house.

Mr./Ms:
Address: Apt. #:
City: State: Zip Code:

Phone #: ( ) Work Phone #: ( )
Date Purchased:
Model #:
Purchased From:

P ART # DESCRIPTION QUANTITY
1 Rear Unit Assembly 1

EXAMPLE:

TELEPHONE

CUSTOMER SERVICE

Tel: [phone]

FAX

CUSTOMER SERVICE

Fax: [phone]

MAIL

STAMINA PRODUCTS, INC.

ATTN: Customer Service

P.O. Box 1071

Springfield, MO. 65801-1071

ONLINE

CUSTOMER SERVICE

[e-mail]

[e-mail]

www.staminaproducts.com