Stamina 20-2018 Owner's Manual

When calling for parts or

service, please specify

the following number

:

Model#: 20-2018

CAUTION:
Weight on this product should not exceed 250 lbs.

Owner's

Manual

This Product is Distributed Exclusively by

2040 N. Alliance, Springeld, MO 65803

Customer Service

1 [phone]

www.staminaproducts.com

Product May Vary Slightly From Pictured.

STAMINA PRODUCTS

MADE IN CHINA

©

2015 Stamina Products, Inc.

2015, 01

Exercise can present a
health risk. Consult a
physician before beginning
any exercise program with
this equipment. If you feel
faint or dizzy, immediately
discontinue use of this
equipment. Serious bodily
injury can occur if this
equipment is not assembled
and used correctly. Serious
bodily injury can also occur
if all instructions are not
followed. Keep others and
pets away from equipment
when in use. Always make
sure all bolts and nuts are
securely tightened prior to
each use. Follow all safety
instructions in this manual.

!

WARNING

TABLE OF CONTENTS

SAFETY INSTRUCTIONS

2

1. Save these instructions and ensure that other exercisers read this manual prior to using the

STAMINA

│X

AB/Hyper Bench for the rst time.

2. Read all warnings and cautions posted on the STAMINA

│X

AB/Hyper Bench.

3. The STAMINA

│X

AB/Hyper Bench should only be used after a thorough review of the Owner’s

Manual. Make sure that it is properly assembled and tightened before use.

4. We recommend that two people be available for assembly of this product.

5. Keep children away from the STAMINA

│X

AB/Hyper Bench. Do not allow children to use or play

on the STAMINA

│X

AB/Hyper Bench. Keep children and pets away from the STAMINA│X AB/

Hyper Bench when it is in use.

6. It is recommended that you place this exercise equipment on an equipment mat.

7. Set up and operate the STAMINA

│X

AB/Hyper Bench on a solid level surface. Do not position

the STAMINA

│X

AB/Hyper Bench on loose rugs or uneven surfaces.

8. Make sure that adequate space is available for access to and around the STAMINA

│X

AB/Hyper

Bench.

9. Before using, inspect the STAMINA

│X

AB/Hyper Bench for worn or loose components, and

securely tighten or replace any worn or loose components prior to use.

10. Consult a physician prior to commencing an exercise program and follow his/her

recommendations in developing your tness program. If at any time during exercise you feel faint,

dizzy, or experience pain, stop and consult your physician.

11. Always choose the workout which best ts your physical strength and exibility level. Know your

limits and train within them. Always use common sense when exercising.

12. Do not wear loose or dangling clothing while using the STAMINA

│X

AB/Hyper Bench.

13. Never exercise in bare feet or socks; always wear proper footwear such as running, walking, or

cross training shoes that t well, provide foot support, and feature non-skid rubber soles.

14. Be careful to maintain your balance while using, mounting, dismounting, or assembling the

STAMINA

│X

AB/Hyper Bench, loss of balance may result in a fall and serious bodily injury.

15. The STAMINA

│X

AB/Hyper Bench should not be used by persons weighing over 250 pounds.

16. The STAMINA

│X

AB/Hyper Bench should be used by only one person at a time.

17. The STAMINA

│X

AB/Hyper Bench is for consumer use only. It is not for use in public or

semipublic facilities.

!

WARNING

This product contains a chemical known to the State of California to cause
cancer and birth defects or other reproductive harm.
Consult your physician before starting this or any exercise program. This is

especially important if you are over the age of 35, have never exercised before,

are pregnant, or suffer from any health problem. This product is for home use
only. Do not use in institutional or commercial applications. Failure to follow all
warnings and instructions could result in bodily injury and property damage.
To reduce the risk of serious injury, read the following Safety Instructions
before using the STAMINA

│X

AB/Hyper Bench.

!

WARNING

!

CAUTION

Safety Instructions ...................................... 2

Before You Begin ........................................ 4

Equipment Warning, Caution & Notice Labels ... 5

Hardware Identication Chart .................... 6

Assembly Instructions ................................ 7

Operational Instructions ........................... 11

Storage ....................................................... 13

Maintenance ............................................... 13

Conditioning Guidelines ........................... 14

Warm-Up and Cool-Down ......................... 15

Product Parts Drawing .............................. 16

Parts List .................................................... 17

Warranty ..................................................... 18

Fax/Mail Ordering Form ............................ 19

Your STAMINA│X AB/Hyper Bench does require assembly.

Please follow the assembly steps set forth in this manual.

With regular workouts, you will be getting your body into shape

and be on your way to achieving a happier and healthier lifestyle.

3

Should you have any questions,

please call our Customer Service Department toll-free number,

1 [phone]

Monday - Thursday, 7:30 A.M. - 5:00 P.M., Central Time.

Friday, 8:00 A.M. - 3:00 P.M., Central Time.

TELEPHONE

CUSTOMER SERVICE

Tel: [phone]

FAX

CUSTOMER SERVICE

Fax: [phone]

MAIL

STAMINA PRODUCTS, INC.

ATTN: Customer Service

P.O. Box 1071

Springeld, MO. 65801-1071

ONLINE

CUSTOMER SERVICE

[e-mail]

www.staminaproducts.com

To enact your warranty, please register your product

by going to register.staminaproducts.com

Call Us First

www.staminaproducts.com

1 [phone]

Customer Service

THANK YOU FOR PURCHASING THE

STAMINA│X AB/Hyper Bench

Foam Roll

Foam Grip

Right Handrail

Knee Cushion

Securing

Knob

BEFORE YOU BEGIN

4

THE FOLLOWING TOOLS ARE INCLUDED FOR ASSEMBLY : Wrench (2 pieces)

Ankle Support

Main Support

Thank you for choosing the STAMINA

│X

AB/

Hyper Bench. We take great pride in producing

this quality product and hope it will provide many
hours of quality exercise to make you feel better,
look better, and enjoy life to its fullest.

It's a proven fact that a regular exercise program
can improve your physical and mental health.
Too often, our busy lifestyles limit our time and
opportunity to exercise. The STAMINA

│X

AB/

Hyper Bench provides a convenient and simple

method to begin your journey of getting your body
in shape and achieving a happier and healthier
lifestyle.

Before reading further, please review the
drawing below and familiarize yourself with the
parts that are labeled.

Read this manual carefully before using the

STAMINA

│X

AB/Hyper Bench.

Although Stamina constructs its products with

the nest materials and uses the highest standards

of manufacturing and quality control, there can
sometimes be missing parts or incorrectly sized
parts. If you have any questions or problems with
the parts included with your STAMINA

│X

AB/

Hyper Bench, please do not return the product.

Contact us FIRST!

If a part is missing or defective, please go to
staminaproducts.com under the Service section
and order the part needed, or call us toll free

at 1-800-375-7520 (in the U.S.). Our Customer

Service Staff is available to assist you from 7:30

A.M. to 5:00 P.M. (Central Time) Monday through
Thursday and 8:00 A.M. to 3:00 P.M. (Central
Time) on Friday.

Be sure to have the name and model number of
the product available when you contact us.

Front
Support

Front Stabilizer

Caution Label

Oval Endcap

Oval Endcap

Rear Stabilizer

Seat

Adjustment

Foam Grip

Adjustment

Knob

Seat Cushion

5

Label is larger than actual size

This chart is provided to help identify the warning, caution, and notice labels on the STAMINA

│X

AB/Hyper Bench. Please take a moment to familiarize yourself with all of the warning, caution, and
notice labels.

EQUIPMENT WARNING, CAUTION & NOTICE LABELS

CAUTION LABEL(41)C1

Part Number and Description Qty

18 Bolt, Hex Head (M10 x 1.5 x 70mm) 1
19 Bolt, Hex Head (M10 x 1.5 x 60mm) 2

6

25 Nylock Nut (M10 x 1.5) 6

23 Washer (M10) 18
24 Washer (M6) 8

20 Bolt, Hex Head (M10 x 1.5 x 20mm) 6
21 Bolt, Hex Head (M6 x 1 x 15mm) 4

length

length

mm.

in.

INCHES

This chart is provided to help identify the hardware used in the assembly process. Place the washers or

the ends of the bolts or screws on the circles to check for the correct diameter. Use the small scale to

check the length of the bolts and screws.

NOTICE: The length of all bolts and screws, except those with flat

heads, is measured from below the head to the end of the bolt
or screw. Flat head bolts and screws are measured from the
top of the head to the end of the bolt or screw.

After unpacking the unit, open the hardware bag and make sure that you have all the following items.
Some hardware may be already attached to the part.

MILLIMETERS

0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150

0 1/2

1 1/2 2 1/2 3 1/2 4 1/2 5 1/2 6

6 8

10 12

3/16"

1/4" 5/16" 3/8" 1/2"

HARDWARE IDENTIFICATION CHART

36 Bolt, Hex Head (M10 x 1.5 x 130mm) 2
37 Bolt, Hex Head (M10 x 1.5 x 120mm) 1

38 Bolt, Hex Head (M6 x 1 x 35mm) 4

ASSEMBLY INSTRUCTIONS

7

FRONT

REAR

Place all parts from the box in a cleared area and position them on the oor in front of you. Remove

all packing materials from your area and place them back into the box. Do not dispose of the packing
materials until assembly is completed. Read each step carefully before beginning. If you are missing
a part, please go to staminaproducts.com under the Service section and order the part needed,

e-mail us at [e-mail], or call us toll free at 1-800-375-7520 (in the
U.S.). Our Customer Service Staff is available to assist you from 7:30 A.M. to 5:00 P.M. (Central
Time) Monday through Thursday and 8:00 A.M. to 3:00 P.M. (Central Time) on Friday.

STEP 1

Insert the REAR STABILIZER(1) into the MAIN SUPPORT(3) and secure with HEX BOLTS(M10x1.5x20mm)
(20), and WASHERS(M10)(23). Press a NUT CAP(M10)(26) onto each bolt head of HEX BOLTS

(M10x1.5x20mm)(20).

STEP 2

Insert the FRONT STABILIZER(2) into the FRONT SUPPORT(4) and secure with HEX BOLTS(M10x1.5x20mm)
(20), and WASHERS(M10)(23). Press a NUT CAP(M10)(26) onto each bolt head of HEX BOLTS
(M10x1.5x20mm)(20).

STEP 3

Attach the FRONT SUPPORT(4) to the MAIN SUPPORT(3) with HEX BOLT(M10x1.5x70mm)(18),
WASHERS(M10)(23), and NYLOCK NUT(M10x1.5)(25). Press the NUT CAPS(M10)(26) onto the bolt head

of HEX BOLT(M10x1.5x70mm)(18) and NYLOCK NUT(M10x1.5)(25). Lock the FRONT SUPPORT(4) in
position by inserting the LOCKING PIN(ø8x60mm)(15) through the bracket on the MAIN SUPPORT(3)
and the FRONT SUPPORT(4).

ASSEMBLY INSTRUCTIONS

8

STEP 4: Attach the two CUSHION RAILS(9) to the FRONT SUPPORT(4) with HEX BOLT(M10x1.5x130mm)

(36), WASHERS(M10)(23), and NYLOCK NUT(M10x1.5)(25). Press the NUT CAPS(M10)(26) onto the
bolt head of HEX BOLT(M10x1.5x130mm)(36) and NYLOCK NUT(M10x1.5)(25).

NOTE: Tighten until snug, the CUSHION RAILS(9) must be allowed to pivot.

STEP 5: Refer to the Illustration. Slide the SEAT ADJUSTMENT(11) around FRONT SUPPORT(4) and

between the CUSHION RAILS(9). To attach the open end of the SEAT ADJUSTMENT(11) to the CUSHION
RAILS(9), insert the HEX BOLT(M10x1.5x130mm)(36) through the WASHERS(M10)(23), CUSHION
RAILS(9), SEAT ADJUSTMENT(11), SPACER(40), and tighten together with NYLOCK NUT(M10x1.5)(25).
Press the NUT CAPS(M10)(26) onto the bolt head of HEX BOLT(M10x1.5x130mm)(36) and NYLOCK
NUT(M10x1.5)(25).

STEP 6: Attach the SEAT CUSHION(35) to the CUSHION RAILS(9) with WASHERS(M6)(24) and HEX

BOLTS(M6x1x35mm)(38).

NOTE: The SEAT CUSHION(35) can be adjusted to different incline positions. To position the SEAT

CUSHION(35) to desired elevation, select one of the holes in the SEAT ADJUSTMENT(11) and

attach the SEAT ADJUSTMENT(11) to one of the holes in the FRONT SUPPORT(4) with the
ADJUSTMENT PIN(ø10x70mm)(39).

ASSEMBLY INSTRUCTIONS

9

STEP 7: Insert the CUSHION POST(5) into the MAIN SUPPORT(3) and lock in position with the

ADJUSTMENT KNOB(13). For added safety, thread the SECURING KNOB(14) into the right side of the
MAIN SUPPORT(3).

NOTE: The pin of the ADJUSTMENT KNOB(13) must be inserted into one of the adjustment holes in the

CUSHION POST(5). The ADJUSTMENT KNOB(13) and SECURING KNOB(14) must be screwed
in completely to ensure that the CUSHION POST(5) will t tightly in the MAIN SUPPORT(3).

STEP 8: Attach the LEFT and RIGHT HANDRAILS(6, 7) to both sides of the CUSHION POST(5) with HEX

BOLTS(M10x1.5x60mm)(19), WASHERS(M10)(23), and NYLOCK NUTS(M10x1.5)(25). Press the NUT
CAPS(M10)(26) onto the bolt heads of HEX BOLTS(M10x1.5x60mm)(19) and NYLOCK NUTS(M10x1.5)

(25).

STEP 9: Attach the KNEE CUSHION(12) to the CUSHION POST(5) with HEX BOLTS(M6x1x15mm)

(21) and WASHERS(M6)(24).
NOTE: There are the selection holes in the CUSHION POST(5) for adjusting the height of the KNEE

CUSHIONS(12).

12

ASSEMBLY INSTRUCTIONS

10

STEP 10

Attach the ANKLE SUPPORT(8) to the MAIN SUPPORT(3) with HEX BOLT(M10x1.5x120mm)(37),
WASHERS(M10)(23), and NYLOCK NUT(M10x1.5)(25). Press the NUT CAPS(M10)(26) onto the bolt

head of HEX BOLT(M10x1.5x120mm)(37) and NYLOCK NUT(M10x1.5)(25).

STEP 11

Slide the FOAM ROLLS(16) onto both sides of the ANKLE SUPPORT(8).

OPERATIONAL INSTRUCTIONS

11

EXERCISE PROGRAM

BACK HYPEREXTENSIONS

DECLINE CRUNCHES

KNEE-INS

INCLINE PUSH-UPS

Once you have completed the assembly of your STAMINA| X AB/Hyper Bench, please
view the following for a list of recommended exercises.
**Dumbbell sold separately

DECLINE PUSH-UPS

BENCH DIPS

SPLIT SQUATS

ONE-ARM ROWS

BICEP CURLS

12

1. To store the STAMINA

│X

AB/Hyper Bench, simply keep it in a clean dry place.

2. Use two people to lift from the FRONT and REAR STABILIZER(2, 1) to move the STAMINA│X AB/

Hyper Bench.

3. Follow the process below to fold the STAMINA│X AB/Hyper Bench as illustrated for easy storage.

The safety and integrity designed into the STAMINA

│X

AB/Hyper Bench can only be maintained when

the STAMINA│X AB/Hyper Bench is regularly examined for damage and wear. Special attention should
be given to the following:

1. Verify that the CAUTION LABEL(41) is in place and easy to read. Call Stamina Products immediately

at 1-800-375-7520 for a replacement CAUTION LABEL(41) if it is missing or damaged.

2. It is the sole responsibility of the user/owner to ensure that regular maintenance is performed.

3. Verify that all nuts and bolts are present and properly tightened. Replace missing nuts and bolts.
Securely tighten loose nuts and bolts.

4. Worn or damaged components shall be replaced immediately or the STAMINA

│X

AB/Hyper Bench

removed from service until repair is made.

5. Only Stamina Products supplied components shall be used to maintain/repair the STAMINA│X AB/

Hyper Bench.

6. Keep your STAMINA

│X

AB/Hyper Bench clean by wiping it off with an absorbent cloth after use.

STORAGE

MAINTENANCE

13

a. Loosen but do not remove the SECURING KNOB(14).

Loosen and pull the ADJUSTMENT KNOB(13), slide
the KNEE CUSHION(12) to the lowest position. Then
lock in position by tightening the ADJUSTMENT
KNOB(13) and SECURING KNOB(14).

b. Refer to illustration A and B. Pull out the ADJUSTMENT

PIN(39) and lower the SEAT CUSHION(35) to the
lowest position. Lock the SEAT CUSHION(35) in
position with the ADJUSTMENT PIN(39).

c. Remove the LOCKING PIN(15) from the MAIN

SUPPORT(3) to fold the FRONT SUPPORT(4). Store
the LOCKING PIN(15) in the hole in the FRONT
SUPPORT(4). The STAMINA

│X

AB/Hyper Bench

should appear as shown in illustration C after folded.

B.

C.

A.

12

How you begin your exercise program depends on your physical condition. If you have been inactive for
several years or are severely overweight, start slowly and increase your workout time gradually. Increase
your workout intensity gradually by monitoring your heart rate while you exercise.

Initially you may only be able to exercise within your target zone for a few minutes; however, your aerobic
capacity will improve over the next six to eight weeks. It is important to pace yourself while you exercise
so you don't tire too quickly.

Measure your heart rate periodically during your workout by stopping the
exercise but continuing to move your legs or walk around. Place two or

three ngers on your wrist and take a six second heartbeat count. Multiply
the results by ten to nd your heart rate. For example, if your six second

heartbeat count is 14, your heart rate is 140 beats per minute. A six second
count is used because your heart rate will drop rapidly when you stop
exercising. Adjust the intensity of your exercise until your heart rate is at the
proper level.

wrist pulse

Remember to follow these essentials:

Have your doctor review your training and diet programs.
Begin your training program slowly with realistic goals that have been set by you and your physician.
Warm up before you exercise and cool down after you work out.

Take your pulse periodically during your workout and strive to stay within a range of 60% (lower

intensity) to 90% (higher intensity) of your maximum heart rate zone. Start at the lower intensity, and
build up to higher intensity as you become more aerobically t.

If you feel dizzy or lightheaded you should slow down or stop exercising.

To determine if you are working out at the correct intensity, use a heart rate monitor or use the table
below. For effective aerobic exercise, your heart rate should be maintained at a level between 60%
and 90% of your maximum heart rate. If just starting an exercise program, work out at the low end of
your target heart rate zone. As your aerobic capacity improves, gradually increase the intensity of your
workout by increasing your heart rate.

CONDITIONING GUIDELINES

Target Heart Rate Zone Estimated by Age*

* For cardiorespiratory training benefits, the American College of Sports Medicine recommends

working out within a heart rate range of 55% to 90% of maximum heart rate. To predict the

maximum heart rate, the following formula was used: 220 - Age = predicted maximum heart rate

20 years

25 years

30 years
35 years

40 years

45 years

50 years

55 years

60 years
65 years
70 years

Average Maximum

Heart Rate 100%

Age

110-180 beats per minute

107-175 beats per minute
105-171 beats per minute
102-166 beats per minute

99-162 beats per minute
97-157 beats per minute
94-153 beats per minute

91-148 beats per minute

88-144 beats per minute

85-139 beats per minute
83-135 beats per minute

200 beats per minute

195 beats per minute

190 beats per minute

185 beats per minute

180 beats per minute

175 beats per minute
170 beats per minute
165 beats per minute
160 beats per minute

155 beats per minute

150 beats per minute

Target Heart Rate Zone

(55%-90% of Maximum Heart Rate)

14

WARM-UP and COOL-DOWN

Warm-Up

The purpose of warming up is to prepare your body for exercise and to minimize injuries.

Warm up for two to ve minutes before strength training or aerobic exercising. Perform activities that

raise your heart rate and warm the working muscles. Activities may include brisk walking, jogging,
jumping jacks, jump rope, and running in place.

Stretching

Stretching while your muscles are warm after a proper warm-up and again after your

strength or aerobic training session is very important. Muscles stretch more easily at these times
because of their elevated temperature, which greatly reduces the risk of injury. Stretches should be held
for 15 to 30 seconds. Do not bounce.

Suggested Stretching Exercises

Remember to always check with your physician before starting any exercise program.

Cool-Down

The purpose of cooling down is to return the body to its normal, or near normal, resting

state at the end of each exercise session. A proper cool-down slowly lowers your heart rate and allows
blood to return to the heart. Your cool-down should include the stretches listed above and should be

completed after each strength training session.

Lower Body Stretch

Place feet shoulder-width

apart and lean forward.
Keep this position for 30
seconds using the body as a
natural weight to stretch the
backs of the legs.

DO NOT BOUNCE!

When the pull on the back of
the legs lessens, gradually
try a lower position.

Floor Stretch

While sitting on the oor,

open the legs as wide as
possible. Stretch the upper
body toward the knee on the
right leg by using your arms
to pull your chest to your
thighs. Hold this stretch 10
to 30 seconds.

DO NOT BOUNCE!

Do this stretch 10 times.
Repeat the stretch with the
left leg.

Bent Over Leg Stretch

Stand with feet shoulder-

width apart and lean forward

as illustrated. Using the

arms, gently pull the upper
body towards the right leg.
Let the head hang down.

DO NOT BOUNCE!

Hold the position a minimum
of 10 seconds. Repeat
pulling the upper body to
the left leg. Do this stretch
several times slowly.

Bent Torso Pulls

While sitting on the oor,

have legs apart, one leg
straight and one knee bent.
Pull the chest down to touch
the thigh on the leg that is
bent, and twist at the waist.
Hold this position at least 10
seconds. Repeat 10 times
on each side.

15

1

12

27

29

PRODUCT PARTS DRAWING

16

FRONT

BACK

PART# PART NAME QTY

PARTS LIST

17

1 Rear Stabilizer 1
2 Front Stabilizer 1
3 Main Support 1
4 Front Support 1
5 Cushion Post 1
6 Left Handrail 1
7 Right Handrail 1
8 Ankle Support 1
9 Cushion Rail 2
10 Foot Plate 2
11 Seat Adjustment 1
12 Knee Cushion 1
13 Adjustment Knob 1
14 Securing Knob 1

15 Locking Pin (ø8 x 60mm) 1

16 Foam Roll 2
17 Foam Grip 2

18 Bolt, Hex Head (M10 x 1.5 x 70mm) 1
19 Bolt, Hex Head (M10 x 1.5 x 60mm) 2
20 Bolt, Hex Head (M10 x 1.5 x 20mm) 6
21 Bolt, Hex Head (M6 x 1 x 15mm) 4
22 Screw, Flat Head (M4 x 15mm) 4
23 Washer (M10) 18
24 Washer (M6) 8
25 Nylock Nut (M10 x 1.5) 6
26 Nut Cap (M10) 18
27 Oval Endcap (30mm x 70mm) 4

28 Bushing 1

29 Square Plug (50mm x 50mm) 1
30 Square Plug (38mm x 38mm) 1
31 Round Plug (ø31.8mm) 2
32 Round Plug (ø25.4mm) 2
33 Square Plug (25mm x 25mm) 6

34 EVA Pad 1
35 Bench Cushion 1

36 Bolt, Hex Head (M10 x 1.5 x 130mm) 2
37 Bolt, Hex Head (M10 x 1.5 x 120mm) 1
38 Bolt, Hex Head (M6 x 1 x 35mm) 4
39 Adjustment Pin (ø10 x 70mm) 1
40 Spacer (ø10.5 x ø16 x 56.5mm) 1

41 Caution Label 1
42 Wrench 2
43 Manual 1

LIMITED WARRANTY

WARRANTY

MODEL 20-2018

18

Stamina Products, Inc. warrants that this product will be free from defects in materials and workmanship
under normal use, service, proper assembly and proper operation for a period of 90 days on the
parts and one year on the frame from the date of the original purchase from an authorized retailer.

THIS WARRANTY SHALL NOT APPLY TO ANY PRODUCT WHICH HAS BEEN SUBJECT
TO COMMERCIAL USE, ABUSE, MISUSE, ALTERATION OF ANY TYPE OR CAUSE OR TO
ANY DEFECT OR DAMAGE CAUSED BY IMPROPER ASSEMBLY, REPAIR, REPLACEMENT,
SUBSTITUTION OR USE WITH PARTS OTHER THAN PARTS PROVIDED BY STAMINA PRODUCTS,
INC. Commercial use includes use of the product in athletic clubs, health clubs, spas, gymnasiums,

exercise facilities, and other public or semipublic facilities whether or not the product's use is in

furtherance of a prot making enterprise, and all other use which is not for personal, family, or household

purposes.

To implement this limited warranty, send a written notice stating your name, date, and place of purchase
and a brief description of the defect along with your receipt to Stamina Products, Inc. P.O. Box 1071,
Springeld Missouri, USA, 65801-1071, or email us at [e-mail], or
call us at 1-800-375-7520. If the defect is covered under this limited warranty, you will be requested to
return the product or part to us for free repair or replacement at our option. NO ACTION FOR BREACH

OF THIS LIMITED WARRANTY MAY BE COMMENCED MORE THAN ONE (1) YEAR AFTER THE
DATE THE ALLEGED BREACH WAS OR SHOULD HAVE BEEN DISCOVERED. NO ACTION FOR
BREACH OF ANY IMPLIED WARRANTY MAY BE COMMENCED MORE THAN ONE (1) YEAR AFTER
DELIVERY OF THE PRODUCT TO THE PURCHASER. This limited warranty is not transferable. IF
ANY PART OF THE PRODUCT IS NOT IN COMPLIANCE WITH THIS LIMITED WARRANTY OR ANY
IMPLIED WARRANTY, THE REMEDY OF REPAIR OR REPLACEMENT IS THE EXCLUSIVE REMEDY
AVAILABLE TO YOU. In the event that the purchaser makes any claim under this limited warranty or any

implied warranty, the Warrantor reserves the right to require the product to be returned for inspection,

at the purchaser's expense, to the Warrantor's premises in Springeld, Missouri. Return of the enclosed

warranty registration card is not required for warranty coverage, but is merely a way of establishing the
date and place of purchase.

Stamina Products, Inc. SHALL NOT BE LIABLE FOR THE LOSS OF USE OF ANY PRODUCT, LOSS

OF TIME, INCONVENIENCE, COMMERCIAL LOSS OR ANY OTHER INDIRECT, CONSEQUENTIAL,
SPECIAL OR INCIDENTAL DAMAGES DUE TO BREACH OF THE ABOVE WARRANTY OR ANY
IMPLIED WARRANTY.

This limited warranty is the only written or express warranty given by Stamina Products, Inc. This

warranty gives you specic legal rights, and you may also have other legal rights which vary from state

to state. ANY OTHER RIGHT WHICH YOU MAY HAVE, INCLUDING ANY IMPLIED WARRANTY OR
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, IS LIMITED IN DURATION TO
THE DURATION OF THIS WARRANTY.

The laws in some jurisdictions restrict the rights of manufacturers and distributors of consumer goods
to disclaim or limit implied warranties and consequential and incidental damages with respect thereto.
If any such law is found to be applicable, the foregoing disclaimers and limitations of and on implied
warranties and consequential and incidental damages with respect thereto shall be disregarded and shall
be deemed not to have been made to the extent necessary to comply with such legal restriction.

Model Number: ...................................................................................... Serial Number: .............................................................................................

Product Name: ..................................................................................................................................................................................................................................

Place Purchased: ..............................................................................................................................................................................................................................

Date of Purchase: .................................................................................. Purchase Price: ............................................................................................

First Name: ............................................................................................ Last Name: ...................................................................................................

City: .................................................................. State: ................................................................ Zip Code: .................................................

Email Address: ....................................................................................... Phone #: ( ) ......................................................................................

Would you like to receive email information or special offers from Stamina Products?* ____Yes ____No

*If yes, be sure your email address is included above.

Stamina Products, Inc.

P.O. Box 1071

Springeld, MO 65801-1071

If there are missing or damaged parts, you can go to parts.staminaproducts.com and order those parts. If you have questions,
please contact customer service. Do not return the product. To order parts by mail, fill out the sheet below and fax it to

417-889-8064. The part will be mailed to your address.

Mr./Ms: ..............................................................................................................................................................................................................................................

Address: ........................................ ............................................................................................. Apt. #:..........................................................................

City: .................................................................. State: ................................................................ Zip Code: .................................................

IMPORTANT : We must have your phone number to process the order!

Phone #: ( ) ................................................................................ Work Phone #: ( ) .............................................................................

Date of Purchase: ..................................................................................

Model #: ............................................................................................................................................................................................................................................

Purchased From: ..............................................................................................................................................................................................................................

IMPORTANT : Before lling out the form below make sure you have the correct information.

Refer to the parts list to make sure you're ordering the right parts!

Stamina Products, Inc.

P.O. Box 1071

Springeld, MO 65801-1071

Detach and Mail or Fax the Form Above

TO REGISTER YOUR PRODUCT

TO CONTACT CUSTOMER SERVICE

TO ORDER PARTS

TO CONTACT CUSTOMER SERVICE

For your convenience, Stamina’s customer service representatives can be reached by email at customerservice@
staminaproducts.com or by phone at 1-800-375-7520 (in the U.S.). Our customer service representatives are available Monday

through Thursday from 7:30 a.m. until 5:00 p.m., and Friday 8:00 a.m. until 3 p.m. Central Time.

TO REGISTER YOUR PRODUCT

Would you like to recieve email information or special offers from Stamina Products? Register at contact.staminaproducts.com

TELEPHONE

CUSTOMER SERVICE

Tel: [phone]

FAX

CUSTOMER SERVICE

Fax: [phone]

MAIL

STAMINA PRODUCTS, INC.

ATTN: Customer Service

P.O. Box 1071 Springeld, MO. 65801-1071

ONLINE

CUSTOMER SERVICE

[e-mail]

www.staminaproducts.com

To enact your warranty, please register your product by going to register.staminaproducts.com. Please have your product model

number (printed on the cover of this owner’s manual) and the serial number (printed on the black and white sticker on your
product) ready.

If you don’t have internet access, you can call customer service at 1-800-375-7520, or ll out and mail the product registration
form below to Stamina Products, Inc.; P.O. Box 1071; Springeld, MO 65801-1071.

PRODUCT REGISTRATION FORM

TO ORDER PARTS

Detach and Mail or Fax the Form Below

PARTS ORDER FORM

PART # DESCRIPTION QUANTITY

1 Rear Unit Assembly 1

EXAMPLE: