ST ST52F510, ST52F513, ST52F514 User Manual

查询ST52F510供应商
ST52F510/F513/F514
8-BIT INTELLIGENT CONTROLLER UNIT (ICU)
Two Timer/PWMs, ADC, I2C, SPI, SCI
Memories
Up to 8 Kbytes Single Voltage Flash Memory
256 bytes of Register Fi le
256 bytes of RAM
Up to 4 Kbytes Data EEPROM
In Situ Programming in Flash devices (ISP)
Single byte and Page modes and In Application
Programming for writing data in Flash memory
Readout protection and flexible write protection
Core
Register File based architecture
107 basic instructions
Hardware multiplication and division
Decision Processor for the implementation of
Fuzzy Logic algorithms
Deep System and User Stacks
Clock and Power Supply
Up to 24 MHz clock frequency
Programmable Oscillator modes:
– 10 MHz Internal Oscillator – External Clock/ Oscillator – External RC Oscillator
Power-On Reset (POR)
Programmable Low Voltage Detector (PLVD)
with 3 configurable thresholds
Power Saving features
Interrupts
8 interrupt vectors with one SW Trap
Non-Maskable Interrupt (NMI)
Two Port Interrupts with up to 16 sources
I/O Ports
From 10 up to 22 I/O PINs configurable in pull-
up, push-pull, weak pull-up, open-drain and high-impedance
High current sink/source in all pins
ST52F510/F513/F514
TARGET SPECIFICATION
Peripherals
On-chip 10-bit A/D Converter with 8 channel
analog multiplexer and Autocalibration.
2 Programmable 16 bit Timer/PWMs with
internal 16-bit Prescaler featuring: – PWM output – Input capture – Output compare – Pulse generator mode
Watchdog timer
Serial Communication Interface (SCI) with
asynchronous protocol (UART).
2
I
C Peripheral with master and slave mode
3-wire SPI
Master and Multi Master SPI modes
Development tools
High level Software tools
‘C’ Compiler
Emulator
Low cost Programmer
Gang Programmer
Peripheral supporting Single
Rev. 1.18 -June 2003 1/106 This is preliminary information on a new product foreseen to be developed. Details are subject to change without notice.
ST52F510/F513/F514
2/106
ST52F510/F513/F514
TABLE OF CONTENTS
TABLE OF CONTENTS
1 GENERAL DESCRIPTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1.1 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
1.2 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
1.2.1 Memory Programming Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
1.2.2 Working Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
1.3 Pin Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
2 INTERNAL ARCHITECTURE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2.1 Control Unit and Data Processing Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
2.1.1 Program Counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2.1.2 Flags. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2.2 Arithmetic Logic Unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
2.3 Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
3 ADDRESSING SPACES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3.1 Memory Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
3.2 Register File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
3.3 Program/Data Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
3.4 System and User Stacks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
3.5 Input Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
3.6 Output registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
3.7 Configuration Registers & Option Bytes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
4 MEMORY PROGRAMMING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
4.1 Program/Data Memory Organization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
4.2 Memory Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
4.2.1 Programming Mode start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
4.2.2 Fast Programming procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
4.2.3 Random data writing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
4.2.4 Option Bytes Programming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
4.3 Memory Verify. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
4.3.1 Fast read procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
4.3.2 Random data reading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
4.4 Memory Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
4.5 ID Code. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
4.6 Error cases . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
4.7 In-Situ Programming (ISP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
4.8 In-Application Programming (IAP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
4.8.1 Single byte write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
4.8.2 Block write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
4.8.3 Memory Corruption Prevention. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
4.8.4 Option Bytes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
4.8.5 Input Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
3/106
ST52F510/F513/F514
5 INTERRUPTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
5.1 Interrupt Processing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
5.2 Global Interrupt Request Enabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
5.3 Interrupt Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
5.4 Interrupt Maskability and Priority Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
5.5 Interrupt RESET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
5.6 Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
6 CLOCK, RESET & POWER SAVING MODES . . . . . . . . . . . . . . . . . . . . . . . . 44
6.1 Clock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
6.2 Reset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
6.2.1 External Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
6.2.2 Reset Procedures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
6.3 Programmable Low Voltage Detector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
6.4 Power Saving modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
6.4.1 Wait Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
6.4.2 Halt Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
6.5 Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
6.5.1 Configuration Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
6.5.2 Option Bytes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
7 I/O PORTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
7.1 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
7.2 Input Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
7.3 Output Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
7.4 Interrupt Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
7.5 Alternate Functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
7.6 Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
7.6.1 Configuration Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
7.6.2 Input Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
7.6.3 Output Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
8 FUZZY COMPUTATION (DP). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
8.1 Fuzzy Inference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
8.2 Fuzzyfication Phase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
8.3 Inference Phase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
8.4 Defuzzyfication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
8.5 Input Membership Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
8.6 Output Singleton. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
8.7 Fuzzy Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
9 INSTRUCTION SET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
9.1 Addressing Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
9.2 Instruction Types. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
10 10-bit A/D CONVERTER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
10.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
4/106
ST52F510/F513/F514
10.2 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
10.3 Operating Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
10.3.1 One Channel Single Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
10.3.2 Multiple Channels Single Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
10.3.3 One Channel Continuous Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
10.3.4 Multiple Channels Continuous Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
10.4 Power Down Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67
10.5 A/D Converter Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67
10.5.1 A/D Converter Configuration Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
10.5.2 Input Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
11 WATCHDOG TIMER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
11.1 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
11.2 Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
12 PWM/TIMERS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
12.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
12.2 Timer Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
12.3 PWM Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73
12.3.1 Simultaneous Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
12.4 Timer Interrupts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74
12.5 PWM/Timer 0 Register Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74
12.5.1 PWM/Timer 0 Configuration Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
12.5.2 PWM/Timer 0 Input Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
12.5.3 PWM/Timer 0 Output Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
12.6 PWM/Timer 1 Register Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
12.6.1 PWM/Timer 1 Configuration Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
12.6.2 PWM/Timer 1 Input Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
12.6.3 PWM/Timer 1 Output Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
13 SERIAL COMMUNICATION INTERFACE. . . . . . . . . . . . . . . . . . . . . . . . . . . 80
13.1 SCI Receiver block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80
13.1.1 Recovery Buffer Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
13.1.2 SCDR_RX Block. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
13.2 SCI Transmitter Block. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82
13.3 Baud Rate Generator Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82
13.4 SCI Register Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84
13.4.1 SCI Configuration Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
13.4.2 SCI Input Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
13.4.3 SCI Output Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
14 I2C BUS INTERFACE (I2C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
14.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86
14.2 Main Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86
14.3 General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86
5/106
ST52F510/F513/F514
14.3.1 Mode Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
14.3.2 Communication Flow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
14.3.3 SDA/SCL Line Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
14.4 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87
14.4.1 Slave Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
14.4.2 Master Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
14.5 Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .92
14.5.1 I2C Interface Configuration Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
14.5.2 I2C Interface Input Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
14.5.3 I2C Interface Output Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
15 SERIAL PERIPHERAL INTERFACE (SPI) . . . . . . . . . . . . . . . . . . . . . . . . . . 96
15.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96
15.2 Main Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96
15.3 General description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96
15.4 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96
15.4.1 Master Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
15.4.2 Slave Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
15.4.3 Data Transfer Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
15.4.4 Write Collision Error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
15.4.5 Master Mode Fault . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
15.4.6 Overrun Condition. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
15.4.7 Single Master and Multimaster Configurations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
15.4.8 Interrupts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
15.5 SPI Register Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .103
15.5.1 SPI Configuration Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
15.5.2 SPI Input Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
15.5.3 SPI Output Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
6/106
ST52F510/F513/F514
1 GENERAL DESCRIPTION
1.1 Introduction
ST52F510/F513/F514 are devices of ST FIVE family of 8-bit Intelligent Controller Units (ICU), which can perform, both boolean and Fuzzy algorithms in an efficient manner, in order to reach the best performances that the two methodologies allow.
Produced by STMicroelectronics using the reliable high performance CMOS process for Single Voltage Flash versions, ST52F510/F513/F514 include integrated on-chip peripherals that allow maximization of system re liability, and decreased system costs in orde r to minimize the number of external components.
The flexible I/O co nfiguration of ST52F510/F513/ F514 allow one to interf ace with a wide range of external devices (for example D/A converters or power control devices), and to c ommunicate with the most common serial standards.
ST52F510/F513/F514 pins are configurable. The user can set input or output signals on each single pin in 8 different modes, reducing the need for external components in orde r to supply a suitable interface with the port pins.
A hardware multiplier an d divider, together wit h a wide instruction set, allow the implementation of complex functions by using a single instruction. Therefore, program memory utilization and computational speed is optimized.
Fuzzy Logic dedicated structures in ST52F510/
F513/F514 ICU’s can be exploited to model complex system with high accuracy in a useful and simple manner.
Fuzzy Expert Systems for overall system management and Fuzzy Real time Controls can be designed to increase per formance at competitive costs.
The linguistic approach characterizing Fuzzy Logic is based on a set of IF-THEN rules, which describe the control behavior and on Membership Functions associated with input and output variables.
Up to 340 Membership Fun ctions, with triangular and trapezoidal shapes, or singleton values are available to describe fuzzy variables.
The Timer/PWM periph eral all ows o ne to m anage power devices and timing signals, by implementing different operating modes and high frequency PWM (Pulse Width Modulation) controls. Input Capture and Output Compare functions are available on the Timers.
The Timer has a 16-bit programmable internal Prescaler and a 16-bit Counter, which can use internal or external START/STOP signals and clock.
An internal programmable WATCHDOG is available to avoid loop errors and reset the ICU.
ST52F510/F513/F514 includes a 10-bit, self­calibrating, Analog to Digital Converter with an 8 ­analog channel Multiplexer. Single/Multiple channels and Single/Sequence conversion modes are supported. External reference can be supplied to obtain more stability and precision in the conversion.
ST52F510/F513/F514 supply differ ent per ipheral s to implement the most common serial communication protocols. SCI allows the performance of serial asynchronous communication (UART). I allow the implementation of synchronous serial protocols. I
2
C peripherals can work both in master
2
C and SPI peripherals
and slave mode. SPI imple ments S ingle and Mul ti Master modes using 3-wire.
Up to 8 interrupt vectors are available, which allow synchronization with peripherals and external devices. Non-Maskable Int errupt and S/W TRAP are available. All interrupts have configurable priority levels and are maskable excluding the Non-Maskable Interr upt, which has fixed top level priority. Two versatile Por t Interru pts are avail able for synchronization with external sources.
The ST52F510/F513/F514 also include an on-chip Power-on-Reset (POR), which provides an internal chip reset during power up situation and a Programmable Low Voltage Detector (PLVD), which causes the ICU to reset if the voltage source V
dips below a thresho ld. Three progr ammable
DD
thresholds are available, allowing to work with different supply voltages (from 2.7 to 5.5 V).
In order to optimize energy consumption, two different power savin g modes are available: Wait mode and Halt mode.
Internal Oscillator at 10 MHz ± 1% is available. External clock, quartz oscillator or RC oscillator are also applicable. The device alw ays starts with the Internal Oscillator, then it reads an Option Byte where the clock mode to be used is programmed.
Program Memory addressing capability addresses up to 8 Kbytes of memory location to store both program instructions and data.
Memory can be locked by the user in order to prevent external undesired operations.
Operations may be performed on data stored in RAM, allowing direct combination of new inputs and feedback data. All RAM bytes are used like Register File.
An additional RAM bench is added to the Program Memory addressing space in order to allow the management of the S y ste m/User Sta ck s an d u se r data storage.
7/106
ST52F510/F513/F514
ST52F510/F513/F514 supply the system stack and the user stack located in the addit ional RAM bench. The user stack can be located anywhere in the additional RAM by writing the top address in the configuration registers, in order to avoid overlap with other data.
Single Voltage Flash allo ws the use r to reprogram the devices on-board by means of the In Situ Programming (ISP) feature. It is possible to store in safe way up to 4K of data in the available EEPROM memory benches. Perma nent data, both in Flash and EEPROM can be man aged by means of the In-Application-Programming (IAP) feature. Single byte and Page write modes are supported. Flexible write protection, of permanent data or program instructions, is also available.
The Instruction Set composed of up to 107 instructions allows code compression and high speed in the program implementation.
A powerful development environment consisting of a board and software tools allows an easy configuration and use of ST52F510/F513 /F514 .
The Visual FIVE software tool allows the development and debugging of projects via a user­friendly graphical interface and optimization of generated microcode.
Third-party Hardwa re Emulato rs and ‘C ’ Compiler are available to speed-up the application implementation and time-to-market.
1.2 Functional Description
ST52F510/F513/F514 ICU’s can work in two modes according to the Vpp signal levels:
Memory Programming Mode
Working Mode
During Working Mode Vpp must be tied to Vss. To enter the Memory Programming Mode, the Vpp pin must be tied to Vdd.
A RESET signal must be appli ed to the device to switch from one mode to the other.
1.2.1 Memory Programming Mode.
The ST52F510/F513/F514 memory is loaded in the Memory Programming Mode. All instructions and data are written inside the memory during this phase.
The Option Bytes are l oaded during t his p hase b y using the programming tools. The Option Bytes can only be loaded in this phase and cannot be modified run-time.
Data and commands are trans mitted by using the
2
I
C protocol, implemented using the internal I2C peripheral. The In-Situ Programming protocol (ISP) uses the following pins:
SDA and SCL for transmission
Vpp for entering in the mode
RESET for starting the protocol in a stable status
Vdd and Vss for the power supply.
The Internal clock is used in this phase.
1.2.2 Working Mode.
The processor starts the wor king phase following the instructions, which have been previously loaded in the first locations of the memory. The first instruction must be a jump to the first program instruction, skipping the data (interrupt vectors, Membership Functions, user data) stored in the first memory page.
ST52F510/F513/F514’s internal structure includes two computational blocks, the CONTROL UNIT (CU) and the DATA PROCESSING UNI T (DPU), which performs boolean functions. The DECISION PROCESSOR (DP) block cooperates with these blocks to perform Fuzzy algorithms.
The DP can manage up to 340 different Membership Function s for the antecedent part of fuzzy rules. The conseq uent terms of the rules are “crisp” values (real numbers). The maximum number of rules that can be defi ned is limited by the dimensions of the standard algorithm implemented.
The Program/Data Memory is shared between Fuzzy and standard algorithms. Within this memory, the user d ata can be s tored both in n on volatile memory as well as in the RAM locations.
The Control Unit (CU) reads informati on and the status of the peripherals.
Arithmetic calculus can be performed on these values by using t he inte rnal CU and Register File, which supports all c omputations. The peripheral inputs can be Fuzzy and/or arithmetic output values contained in the Register File or Pr ogram/ Data Memory.
8/106
ST52F510/F513/F514
Table 1.1 ST52F510/F513/F514 Devices Summary
Device NVM RF RAM EEPROM Timers ADC Comms I/O Package
ST52F510YmM6 4/8 K FLASH 256 256 - 2X16-bit
ST52F510FmM6 4/8 K FLASH 256 256 - 2X16-bit
ST52F510FmB6 4/8 K FLASH 256 256 - 2X16-bit
ST52F510GmM6 4/8 K FLASH 256 256
ST52F510GmB6 4/8 K FLASH 256 256 - 2X16-bit
ST52F513YmM6 4/8 K FLASH 256 256 256 2X16-bit
ST52F513FmM6 4/8 K FLASH 256 256 256 2X16-bit
ST52F513FmB6 4/8 K FLASH 256 256 256 2X16-bit
ST52F513GmM6 4/8 K FLASH 256 256 256 2X16-bit
ST52F513GmB6 4/8 K FLASH 256 256 256 2X16-bit
ST52F514YmM6 4 K FLASH 256 256 1024 / 4096 2X16-bit
ST52F514FmM6 4 K FLASH 256 256 1024 / 4096 2X16-bit
ST52F514FmB6 4 K FLASH 256 256 1024 / 4096 2X16-bit
ST52F514GmM6 4 K FLASH 256 256 1024 / 4096 2X16-bit
ST52F514GmB6 4 K FLASH 256 256 1024 / 4096 2X16-bit
-
2X16-bit
10-bit
2 Ch
10-bit
6 Ch
10-bit
6 Ch
10-bit
8 Ch
10-bit
8 Ch
10-bit
2 Ch
10-bit
6 Ch
10-bit
6 Ch
10-bit
8 Ch
10-bit
8 Ch
10-bit
2 Ch
10-bit
6 Ch
10-bit
6 Ch
10-bit
8 Ch
10-bit
8 Ch
SCI I
SCI I
SCI I
SCI I
SCI I
SCI I
SCI I
SCI I
SCI I
SCI I
SCI I
SCI I
SCI I
SCI I
SCI I
2
C SPI
2
C SPI
2
C SPI
2
C SPI
2
C SPI
2
C SPI
2
2
2
2
2
2
2
2
2
C
C
C
C
C
C
C
C
C
10 So 16
14 So 20
14 Dip 20
22 So 28
22 SDip 32
10 So 16
14 So 20
14 Dip 20
22 So 28
22 SDip 32
10 So 16
14 So 20
14 Dip 20
22 So 28
22 SDip 32
COMMON FEATURES ST52F510/F513 /F5 14
Watchdog Yes
Other Features NMI, PLVD, POR
Temperature Range From -40° to +85
Operating Supply 2.7 - 5.5 V
CPU Frequency from 1 to 24 MHz.
Legend:
Sales code: ST52tnnncmpy Memory type (t): F=FLASH Subfamily (nnn): 510, 513, 514 Pin Count (c): Y=16 pins, F=20 pins, G=28 pins, K=32/34 pins
Memory Size (m):
Packages (p): B=PDIP, M=PSO, T=TQFP Temperature (y): 0=+25, 1=0 +70, 3=-40 +125, 5=-10 +85, 6=-40 +85, 7=-40 +105
2=4 Kb, 3=8 Kb Flash (ST52F510 & ST52F513) 1=1024, 3=4096 EEPROM (only ST52F514)
°
9/106
ST52F510/F513/F514
Figure 1.1 ST52F510/F513/F514 Block Diagram
MEMORY
FLASH
ISP/IAP
DATA RAM
256 bytes
DATA
EEPROM
MEMORY
INTERFACE
I2C
PA7:0
PORT A
TIMER/PWM 0
TIMER/PWM 1
CORE
ALU &
DPU
DECISION
PROCESSOR
CONTROL
UNIT
Register File
256 bytes
Input
registers
ADC
PORT B
SPI
PORT C
SCI
PC FLAGS
WATCHDOG
POWER SUPPLY
& PLVD
VDD VPP VSS OSCIN OSCOUT RESET
OSCILLATOR
POWER ON
RESET
PB7:0
PC5:0
10/106
Figure 1.2 ST52F510/F513/F514 SO20/DIP20 Pin Configuration
ST52F510/F513/F514
Vdd
OscOut
OscIn
Vpp
PB0/VREF/AIN0
PB1/AIN1 PB2/AIN2 PB3/AIN3 PB4/AIN4 PB5/AIN5
1
2
3
4
5
6
7
8
9
10
SO20 DIP20
20
19
18
17
16
15
14
13
12
11
Vss RESET
PA0/SCL PA1/SDA PA2/T1OUT PA3/RX PA4/TSTRT PA5/TCLK/TX PA6/T0OUT PA7/INT
OscOut
PB0/VREF/AIN0
PB1/AIN1 PB2/AIN2 PB3/AIN3 PB4/AIN4 PB5/AIN5
Figure 1.3 ST52F510/F513/F514 SO16 Pin Configuration
Vdd
OscIn
Vpp
1
2
3
4
5
6
7
8
9
10
20
19
18
17
16
15
14
13
12
11
Vss RESET PA0/SCL PA1/SDA PA2/T1OUT PA3/RX PA4/TSTRT PA5/TCLK/TX PA6/T0OUT PA7/INT
Vdd
OscOut
OscIn
Vpp
PB0/VREF/AIN0
PB1/AIN1
PA7/INT
PA6/T0OUT
1
2
3
4
5
6
7
8
SO16
16
15
14
13
12
11
10
9
Vss RESET
PA0/SCL PA1/SDA PA2/T1OUT PA3/RX PA4/TSTRT PA5/TCLK/TX
11/106
ST52F510/F513/F514
Figure 1.4 ST52F510/F513/F514 SDIP32/DIP28 Pin Configuration
Vdd
VddIO
OscOut
OscIn
Vpp
PB0/VREF/AIN0
PB1/AIN1 PB2/AIN2 PB3/AIN3 PB4/AIN4 PB5/AIN5 PB6/AIN6
PB7AIN7
PC0/SCK
PC1/MOSI
N.C.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
SDIP32
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
Vss VssIO RESET
PA0/SCL PA1/SDA PA2/T1OUT PA3/RX PA4/TSTRT PA5/TCLK/TX PA6/T0OUT PA7/INT PC5/TRES PC4/TX PC3/SS PC2MISO
N.C.
Vdd
OscOut
OscIn
Vpp
PB0/VREF/AIN0
PB1/AIN1 PB2/AIN2 PB3/AIN3 PB4/AIN4 PB5/AIN5 PB6/AIN6 PB7/AIN7
PC0/SCK
PC1/MOSI
1
2
3
4
5
6
7
8
9
10
11
12
13
14
SO28
28
27
26
25
24
23
22
21
20
19
18
17
16
15
Vss RESET
PA0/SCL PA1/SDA PA2/T1OUT PA3/RX PA4/TSTRT PA5/TCLK/TX PA6/T0OUT PA7/INT PC5/TRES PC4/TX PC3/SS PC2/MISO
12/106
ST52F510/F513/F514
Table 1.2 ST52F510/F513/F514 SDIP32 Pin List
SDIP32 NAME Programming Phase Working Phase
1 Vdd Digital Power Supply Digital Power Supply 2 VddIO Digital Power Supply Digital I/O Ports Power Supply 3 OSCOUT Oscillator Output 4 OSCIN Oscillator Input
5 Vpp Programming Mode Selector Programming Mode Selector 6 PB0/VREF/AIN0 Digital I/O, A/D Voltage Reference, Analog Input 7 PB1/AIN1 Digital I/O, Analog Input 8 PB2/AIN2 Digital I/O, Analog Input
9 PB3/AIN3 Digital I/O, Analog Input 10 PB4/AIN4 Digital I/O, Analog Input 11 PB5/AIN5 Digital I/O, Analog Input 12 PB6/AIN6 Digital I/O, Analog Input 13 PB7/AIN7 Digital I/O, Analog Input 14 PC0/SCK Digital I/O, SPI Serial Clock 15 PC1/MOSI Digital I/O, SPI Master out Slave in 16 N.C Not Connected 17 N.C Not Connected 18 PC2/MISO Digital I/O, SPI Master in Slave out 19 PC3/SS Digital I/O, SPI Slave Select 20 PC4/TX Digital I/O, SCI Transmission 21 PC5/TRES Digital I/O, Timer/PWM 0 Reset 22 PA7/INT Digital I/O, Non Maskable Interrupt 23 PA6/T0OUT Digital I/O, Timer/PWM 0 output 24 PA5/TCLK/TX Digital I/O, Timer/PWM 0 clock 25 PA4/TSTRT Digital I/O, Timer/PWM 0 start/stop 26 PA3/RX Digital I/O, SCI Reception 27 PA2/T1OUT Digital I/O, Timer/PWM 1 output 28 PA1/SDA Serial Data I/O 29 PA0/SCL Serial Clock 30 RESET General Reset General Reset
Digital I/O, I
Digital I/O, I
2
C Serial Data I/O
2
C Serial Clock
31 VssIO Digital Ground Digital I/O Ports Ground 32 Vss Digital Ground Digital Ground
13/106
ST52F510/F513/F514
Table 1.3 ST52F510/F513/F514 SO28 Pin List
SO28 NAME Programming Phase Working Phase
1 Vdd Digital Power Supply Digital Power Supply
2 OSCOUT Oscillator Output
3 OSCIN Oscillator Input
4 Vpp Programming Mode Selector Programming Mode Selector
5 PB0/VREF/AIN0 Digital I/O, A/D Voltage Reference, Analog Input
6 PB1/AIN1 Digital I/O, Analog Input
7 PB2/AIN2 Digital I/O, Analog Input
8 PB3/AIN3 Digital I/O, Analog Input
9 PB4/AIN4 Digital I/O, Analog Input 10 PB5/AIN5 Digital I/O, Analog Input 11 PB6/AIN6 Digital I/O, Analog Input 12 PB7/AIN7 Digital I/O, Analog Input 13 PC0/SCK Digital I/O, SPI Serial Clock 14 PC1/MOSI Digital I/O, SPI Master out Slave in 15 PC2/MISO Digital I/O, SPI Master in Slave out 16 PC3/SS Digital I/O, SPI Slave Select 17 PC4/TX Digital I/O, SCI Transmission 18 PC5/TRES Digital I/O, Timer/PWM 0 Reset 19 PA7/INT Digital I/O, Non Maskable Interrupt 20 PA6/T0OUT Digital I/O, Timer/PWM 0 output 21 PA5/TCLK/TX Digital I/O, Timer/PWM 0 clock 22 PA4/TSTRT Digital I/O, Timer/PWM 0 start/stop 23 PA3/RX Digital I/O, SCI Reception 24 PA2/T1OUT Digital I/O, Timer/PWM 1 output 25 PA1/SDA Serial Data I/O 26 PA0/SCL Serial Clock 27 RESET General Reset General Reset 28 Vss Digital Ground Digital Ground
Digital I/O, I
Digital I/O, I
2
C Serial Data I/O
2
C Serial Clock
14/106
Table 1.4 ST52F510/F513/F514 SO20/DIP20/SO16 Pin List
ST52F510/F513/F514
SO20
DIP20
SO16 NAME Programming Phase Working Phase
1 1 Vdd Digital Power Supply Digital Power Supply
2 2 OSCOUT Oscillator Output
3 3 OSCIN Oscillator Input
4 4 Vpp Programming Mode Selector Programming Mode Selector
5 5 PB0/VREF/AIN0 Digital I/O, A/D Voltage Reference, Analog Input
6 6 PB1/AIN1 Digital I/O, Analog Input
7 - PB2/AIN2 Digital I/O, Analog Input
8 - PB3/AIN3 Digital I/O, Analog Input
9 - PB4/AIN4 Digital I/O, Analog Input 10 - PB5/AIN5 Digital I/O, Analog Input 11 7 PA7/INT Digital I/O, Non Maskable Interrupt 12 8 PA6/T0OUT Digital I/O, Timer/PWM 0 output 13 9 PA5/TCLK/TX Digital I/O, Timer/PWM 0 clock, SCI transmission 14 10 PA4/TSTRT Digital I/O, Timer/PWM 0 start/stop 15 11 PA3/RX Digital I/O , SCI Re ce ptio n 16 12 PA2/T1OUT Digital I/O, Timer/PWM 1 output 17 13 PA1/SDA Serial Data I/O 18 14 PA0/SCL Serial Clock 19 15 RESET General Reset General Reset 20 16 Vss Digital Ground Digital Ground
Digital I/O, I
Digital I/O, I
2
C Serial Data I/O
2
C Serial Clock
15/106
ST52F510/F513/F514
1.3 Pin Description
ST52F510/F513/F514 pins can be set in digital input mode, digital output mo de, i nterr upt mode or in Alternate Functions. Pin configuration is achieved by mean s of the config uration registe rs. The functions of the ST52F510/F513/F514 pins are described below:
V
Main Power Supply Voltage.
DD.
I/O Ports Power Supply Voltage. It is
V
DDIO.
reccomended to connect this pin with a supply voltage de-coupled with V
in order to improve
DD
the immunity from the n oise generated by th e I/O switching.
V
. Digital circuit Ground.
SS
. I/O Ports Ground. See V
V
SSIO
DDIO
VPP. Programming/Working mode selector. During
the Programming p hase V In Working phase V
PP
must be set to VDD.
PP
must be equal to VSS.
OSCin and OSCout. These pins are internally connected to the on-chip oscillator circuit. A quartz crystal or a ceramic resonator can be connected between these two pins in order to allow correct use of ST52F510/F513/F514 with various stability/ cost trade-offs. An external clock signal can be applied to OSCin: in this case OSCout must be grounded. To reduce costs, an RC cir cuit can be applied to the OSCin pi n to establish the internal clock frequency, instead of the quartz. Without any connection, the device can work with its internal clock generator (10 MHz)
PA0-PA7, PB0-PB7,PC0-PC5. These lines are organized as I/O ports. Each pin can be configured as an input, output (with pull- up, pus h-pull, weak­pull-up, open-drain, high-impedance), or as an interrupt source.
VREF, AIN0-AIN7. These pins are used to input the analog signals into the A/D Converter. An analog multiplexer is available to switch these inputs to the A/D Converter. The pin VREF is used to input an external A/D Reference Voltage.
T0OUT, T1OUT. These pins output the signals generated by the PWM/Timer 0 and PWM/Timer 1 peripheral.
TRES, TSTRT, TCLK . These pins are related to the PWM/Timer 0 peripheral and are used for Input Capture and event counting. The TRES pin is used to set/reset the Timer; the TSTRT pin is used to start/stop the counter. The Timer can be driven by the internal clock or by an external signal connected to the TCLK pin.
INT. This pin is used as input for the Non-Maskable (top level) interrupt. The interrupt signal is detected only if the pin is configured in Alternate Function.
SCL, SDA. These pin are used respectively as Serial Clock and Serial Data I/O in I
2
C peripheral protocol. They are used also in Programming Mode to receive and transmit data.
TX, RX. Serial data output of SCI Transmitter block (TX) and Serial data input of the SCI Receiver block (RX).
RESET. This signal is used to reset the ST52F510/ F513/F514 and re-initialize the registers and control signals. It is also used when switching from the Programming Mode to Working Mode and vice versa.
16/106
SCK, MISO, MOSI, SS. These pins are used by the Serial Peripheral Interface (SPI) peripheral. SCK is the serial clock line. MISO (Master In Slave Out) and MOSI (Master Out Slave In) are the serial data lines, which work in input or in output depending on if the devic e is working in slave or master mode. The SS pin allows the selection of the device master/slave mode.
ST52F510/F513/F514
Control
Signals
2 INTERNAL ARCHITECTURE
ST52F510/F513/F514’s architecture is Register File based and is composed of the following blocks and peripherals:
Control Unit (CU)
Data Processing Unit (DPU)
Decision Processor (DP)
ALU
Memory Interface
up to 256 bytes Register File
Program/Data Memory
Data EEPROM
Interrupts Controller
Clock Oscillator
PLVD and POR
Digital I/O ports
Analog Multiplexer and A/D Converter
Timer/PWMs
2
I
C
SPI
SCI
Figure 2.1 CU Block Diagram
2.1 Control Unit and Data Processing Unit
The Control Unit (CU) decodes the instructions stored in the Program Mem ory and gene rates the appropriate control s ignals. The main parts of the CU are illustrated in Figure 2.1.
The five different parts of the CU manage Loading, Logic/Arithmetic, Jump, Control and the Fuzzy instruction set.
The block called “ Collector” manages the sig nals deriving from the different parts of the CU. The collector defines the signals for the Data Processing Unit (DPU) and Decision Processor (DP), as well as for th e different peripherals of the ICU.
The block called “Arbiter” manages the different parts of the CU, so that only one part of the system is activated during working mode.
The CU structure is extremely flexible and was designed with the purp ose of easily adapting the core of the microcontroller to market need s. New instruction sets or new pe ripherals can easil y be included without changing the structure of the microcontroller, maintaining code compatibility.
A set of 107 different instructions is available. Each instruction requires a number of clock pulses to be performed that depe nds on the complexity of the instruction it self. The clock pulses t o execute the instructions are driv en dir ec tly by the ma sterclock, which has the same frequency of the oscillator signal supplied.
MicroCode
A R B I T E R
Clock Master
Loading Instruction Set
Logic Arithmetic Instruction Set
Jump Instruction Set
Control Instruction Set
Decision Processor
Instruction Set
C O L L E C T O R
17/106
ST52F510/F513/F514
Figure 2.2 Data Processing Unit (DPU)
Interrupts Unit
Program Memory
Input Registers
Peripherals
REGISTER FILE
ADDRESS
PROGRAM COUNTER
REGISTER
FILE
256 Bytes
ACCUMULATOR
FLAGS REG.
DECISION
PROCESSOR
REGISTERS
ALU
Memory Address
Control Unit
Peripherals
The DPU receives, stores and sends the instructions deriving from the Program/Data Memory, Register File or from the peripherals. It is controlled by the CU on the basis of the dec oded instruction. The Fuzzy registers store the partial results of the f uz zy c om puta tion. The accumul ator register is used by the ALU and i s not accessible directly: the instructions used by the ALU can address all the Register File locations as operands, allowing a more compact code and a faster execution.
The following addressing modes are available: inherent, immediate, direct, indirect, bit direct.
2.1.1 Program Counter.
The Program Counter (PC) is a 16-bit register that contains the addre ss of the next memory location to be processed by the core. This memory location may be both an instruction or data address.
The Program Counter’s 16-bit length allows the direct addressing of a maximum of 64 Kbytes in the Program/Data Memory space.
18/106
The PC can be changed in the following ways:
JP (Jump) PC = Jump Address
Interrupt PC = Interrupt Vector
RETI PC = Pop (stack)
RET PC = Pop (stack)
CALL PC = Subroutines address
Reset PC = Reset Vector
Normal Instruction PC = PC + 1
2.1.2 Flags.
The ST FIVE core includes differen t sets of flags that correspond to 2 different modes: normal mode and interrupt mode. Each set of fla gs consist of a CARRY flag (C), ZERO flag (Z) and SIGN flag (S). Each set is stacked: one set of flags is used during normal operation and oth er sets are used during each level of interrupt. Formally, the user has to manage only one set of flags: C, Z and S since the flag stack operation is performed automatically.
ST52F510/F513/F514
Each interrupt leve l ha s i t s own set of flags, which is saved in the Flag Stack during interrupt servicing. These flags are restored from the Flag Stack automatically when a RETI instruction is executed.
If the ICU was in normal mode before an interrupt, after the RETI instruction is executed, the normal flags are restored.
Note: A subroutine CALL is a normal mode execution. For this reason a RET instruction,
consequent to a CALL instruction, doesn’t affect the normal mode set of flags.
Flags are not cleared during context switching and remain in the state they were in at the exit of the last interrupt routine switching.
The Carry flag is set when an overflow occurs during arithmetic operations, otherwise it is cleared. The Sign flag is set when an underflow occurs during arithmetic operations, otherwise it is cleared.
The flags, related to the current context, can be checked by reading the FLAGS Input Register 38 (026h).
2.2 Arithmetic Logic Unit
The 8-bit Arithmetic Logic Unit (ALU) performs arithmetic calcu lations and l ogic instructi ons such as: sum, subtraction , bitwise AND, OR, XOR, bit set and reset, bit test and branch, right/left shift and rotate (see the Chapter 9 Instruction Set for further details).
In addition, the ALU of ST52F510/F513/F514 can perform multiplicati on (MULT) and division (DIV). Multiplication is performed by using 8 bit operands storing the result in 2 registers (16 bi t values); the division instruction addresses the MSB of the dividend (the LSB is stored in the next addres s): the result and remainder are stored in these source addresses (see Figure 2.3 and Figure 2.4).
In order to manage s igned type values, the ALU also performs additio n and subtraction with offset (ADDO and SUBO). These instructions respectively subtract and add 128 to the overall result, in order to ma nage values logically in the range between -128,127.
Figure 2.3 Multiplication
RAM
000h 001h 002h
i
j-1 j j+1
0FDh 0FEh 0FFh
REG. j REG. i
LSB
X
16 Bit
MSB
Figure 2.4 Division
REG. j REG. j+1
RAM
000h 001h 002h
i-1
i
i+1
j-1 j j+1
0FDh
0FEh 0FFh
:
REMAINDER QUOTIENT
REG. i
19/106
ST52F510/F513/F514
2.3 Register Description
Flags Register (FLAG)
Input Register 38 (026h) Read Only Reset Value: 0000 0000 (00h)
70
-----ZSC
Bit 7-3: Not Used
Bit 2: Z Zero flag
Bit 1: S Sign flag
Bit 0: C Carry flag
20/106
ST52F510/F513/F514
3 ADDRESSING SPACES
ST52F510/F513/F514 has six separate addressing spaces:
Register File
Program/Data Memory
Stacks
In put Regi st er s
Output Registers
Configuration Registers
Each space is addressed by a load type instruction that indicates the source and the destination space in the mnemonic code (see Figure 3.1).
3.1 Memory Interface
The read/write operation in the s pace addresses are managed by the Memo ry Inter face , whic h ca n recognize the ty pe of memor y addressed a nd set the appropriate access time and mode.
In addition, the Memory Interface manages the In Application Program ming (IAP) functions in Flash devices like writing cycle and memory write protection.
Figure 3.1 Addressing Spaces
3.2 Register File
The Register File con sist s o f 2 56 g ene ra l p urpos e
8-bit RAM locations called “registers” in order to recall the functionality.
The Register File exchanges data with all the other addressing spaces and is used by the ALU to perform all the arithmetic and logic instructions. These instructions have any Register File address as operands.
Data can be moved from one location to another by using the LDRR inst ruction; see further ahead for information on the instr uction used to move data between the Register File and the other addressing spaces.
3.3 Program/Data Memory
The Program/Data Memory con sists of both non­volatile memory (Flash, EEPROM) and RAM memory benches.
Non-volatil e memory (NV M) is mainly us ed to store the user program and can al so be used to store permanent data (constant, look-up tables).
Each RAM bench consists of 256 locations used to store run-time user data. At least one bench is present in the devices. RAM benches are also used to implement both System and User Stacks .
PROGRAM/DATA MEMORY
NON VOLATILE MEMORY
RAM BANKS AND STACKS
LDCE
LDPE
LDER
LDRE
STFive CORE
REGISTER FI LE
INPUT REGISTERS
LDFR
LDRI
LDCNF GETPG
DECISION
PROCESSOR
REGISTERS
PGSETR
PROGRAM COUNTER
CU DPU ALU
LDPR
LDCR
ON CHIP PERIPHERALS
OUTPUT
REGISTERS
PERIPHERAL
CONFIGURATION
REGISTERS
PERIPHERAL
PERIPHERAL
BLOCK
BLOCK
BLOCK
21/106
ST52F510/F513/F514
NVM is always located beginning after the first locations of the addressing space. RAM banks are always located after NVM.
NVM is organized in acco rdance to the following blocks (see Figure 3.2):
Reset Vector block
(from address 0 to 2) contains an absolute jump instruction to the first user program instruction. The Assembler tool automatically fills these locations with correct data.
Interrupt Vectors block
(from location 3 up to
32) contains the interrupt vectors. Each address is composed of three bytes (the jump opcode and the 16 bit address). Interrupt vectors are set by using IRQ pseudo-instruction (see the Programming Manual).
Figure 3.2 Program/Data Memory Organization
FFFFh
~~
307Fh
OPTION BYTES
3000h
~~
20FFh
SYSTEM STACK
Mbfs Setting block
(just after the interrupt vectors) contains the coordinates of the vertexes of every Mbf defined in the program. The last address that can be assigned to this block is
1023. This area is dynamically assigned according to the size of the fuzzy routines. The memory area that remains unused, if any, is assigned to the Program Instructions block.
The Program Instructions block
(just after the last Mbf data through the last NVM address) contains the instruction of the user program and the permanent data.
Option bytes block
(from location 3000h to 307Fh) is the addressing space reserved for the option bytes. In ST 52F510/F513/F514, o nly the location from 3000h to 3007h are used.
SPACE NOT
ADDRESSABLE
2000h
0400h
0021h
0003h
0000h
DATA
USER STACK
PROGRAM INSTRUCTIONS
AND PERMANENT DATA
PROGRAM INSTRUCTIONS
AND PERMANENT DATA
MEMBERSHIP FUNCTIONS
PARAMETERS
INTERRUPT VECTORS
RESET VECTOR
RAM
BENCH
NON
VOLATILE
MEMORY
22/106
ST52F510/F513/F514
Flash and EEPROM are pr ogrammed electrically just applying the supply voltage (2.7 V to 5.5 V) and it is also erased electrically; this feature allows the user to easily reprogram the memory without taking the device off from the board (In Situ Programming ISP). Data and commands are transmitted through t he I
2
C serial communicatio n protocol. Data can also be written run-time with the In Application Programming (IAP)
NVM can be locked by the user during the programming phase, in orde r to prevent external operation such as rea ding the program code an d assuring protection of user intellectual property. Flash and EEPROM pages can be protected by unintentional writings.
The operations that can be performed on the NVM during the Programmin g Phase, ISP and IAP ar e described in detail in the Section 4.
Figure 3.3 System and User Stack
RAM BENCH
20FFh 20FEh
SYSTEM STACK
POINTER
SYSTEM STACK
LEVEL 1
SYSTEM STACK
LEVEL 2
SYSTEM STACK
LEVEL 3
SYSTEM STACK
LEVEL 4
IRQ
3.4 System and User Stacks
The System and User Stacks are located in the Program/Data memory in the RAM benches.
System Stacks are used to push the Program Counter (PC) after an Interrupt Request or a Subroutine Call. After a RET (Return from a subroutine) or a RETI (Return from an interrupt) the PC that is saved is popped from the stack and restored. After an inter rupt request, the flags are also saved in a r eserved s tack insi de the cor e, so each interrupt has its own flags.
The System Stack is located in the last RAM bench starting from the last address (255) inside the bench page. The System Stack Pointer (SSP) can be read and modified by the user. For each level of stack 2 bytes of the RAM are used. The SSP points to the first currently available stack position. When a subroutine call or interrupt request occurs, the content of the PC is stored in a couple of locations pointed to by the SSP that is decreased by 2.
PROGRAM COUNTE R
RETI
LOCATION ADRESS
PAGE NUMBER
REGISTER FILE
LSB
MSB
USER STACK
POINTER
2001h 2000h
USER DATA
USER STACK LEVEL 4
USER STACK LEVEL 3
USER STACK LEVEL 2
USER STACK LEVEL 1
PUSH X
POP X
REGISTER X
CONFIGURATION REGISTERS
USER STACK TOP LSB
USER STACK TOP MSB
23/106
ST52F510/F513/F514
When a return occurs (R ET or RETI instruction), the SSP is increas ed by 2 and the data stored in the pointed locations co uple is restored back into the PC.
The current SSP can be read and write in the couple of Configuration Reg isters 44 02Ch (MSB : page number, always 32 020h) and 45 02Dh (LSB: location address) ( see Figure 3.3). In ST52F51 0/ F513/F514 the user can only consider the LSB because the MSB is always the same.
The User Stack is used to s tore user data and is located beginning fr om a RAM bench locati on set by the user (USTP) by writing the couple of Configuration Registers 5 005h (MSB: page number) and 6 005h (LSB: location address) (see Figure 3.3). Register 5, which is the page number, must always be set to a va lue between 32 (020h) and 255 (0FFh): values higher than 32 always address RAM on page 32.
Note: In ST52F510/F513/F514 MSB doesn’t have to be set or read because the RAM is only 256 bytes. The LSB of the user stack is equal to 0 at reset. The LSB of the system stack is equal to 255 at reset.
This feature allows a flexible use of the User Stack in terms of dimensi on and to avoid ove rlaps. The User Stack Pointer (USP) points to the first currently availab le stack location. When the user stores a byte value contain ed in the Register File by using the PUSH in structi on, the valu e is store d in the position pointed to by the USP that is increased (the User Stack o rder is oppo site to the System Stack one). Wh en the user takes a valu e from the User Stack with the POP inst ruction, the USP is decreased and the value pointed to is copied in the specified Register File location.
By writing the USTP, the new address is automatically written in the USP. The current USP can be read from the Input Registers 11 0Bh (MSB: page number, always 32 020h) and 12 0Ch (LSB: location address) (see Figure 3.3). In ST52F510/F513/F514 the user can only consider the LSB because the MSB is always the same.
Note: The user must pay close attention to avoid overlapping user and Stacks data. The User Stack Top location and the System Stack Pointer should be configured with c are in order to have enough space between the two stacks.
3.5 Input Registers
The ST52F510/F513/F514 Input Regis ters bench consists of a file of 8-bit regis ters containing data or the status of the p eripherals. For exam ple, the
Input Registers contain data converted by the ADC, Ports, serial communication peripherals, Timers, etc.
The Input Registers can be accessed by using the LDRI instruction that loads the specified Register File address with the contents of the specified Input Register. See the Programming Manual for further details on this instruction. The Input Registers are read-only registers.
In order to simplify the concept, a mnemonic name is assigned to each register. The same name is used in Visual FIVE devel opmen t tools. The list of the Input Registers is shown in Table 3.1.
3.6 Output registers
The ST52F510/F513/F514 Output Registers bench consists of a file of 8-bit registers containing data sent to the Periphe rals and the I/O Port s (for example: Timer Counter s, data to be transmitted by the serial communication peripherals, data to be sent to the Port pins in output, etc.).
The registers are located inside the Peripherals and Ports, which allow flex ibility and modul arity in the design of new family devices.
The Output Registers are write only. In order to access the configuration Register the user can use the following instructions:
LDPI: loads the immediate value in the specified
Output Register.
LDPR: loads the contents of the specified
Register File location into the output register specified. This instruction allows computed data to be sent to Peripherals and Ports.
LDPE direct: loads th e c ont ents of the sp ec ifi ed
Program/Data Memory l ocation into the output register specified. This instruction allows data to be sent to Peripherals and Ports from a table.
LDPE indirect: loads the contents of the
Program/Data Memo ry location whose address is contained in the specified Register File location into the output reg ister specified. This instruction allows da ta to be se nt to Per ipheral s and Ports from a table pointed to by a register.
See the Programming manual for further details about these instructions.
In order to simplify the concept, a mnemonic name is assigned to each register. The same name is used in Visual FIVE devel opmen t tools. The list of the Output Registers is shown in Table 3.2.
24/106
ST52F510/F513/F514
3.7 Configuration Registers & Option Bytes
The ST52F510/F513/F514 Configuration Registers bench con si st s o f a f il e of 8- bit r egi ste rs that allows the configuration of all the ICU blocks. The registers are located inside the block they configure in order to ob tain greater flexibility and modularity in the design of new f amily devices. In the Configuration Registers, each bit has a peculiar use, so the logic level of each of them must be considered.
Some special c onfig urati on dat a, that needs to b e load at the start-up and not further changed, are stored in Option Bytes. These are loaded only during the device program ming phase. See Tabl e
3.3 and Section 4 for a d etailed descr iption of the Option Bytes.
The Configuration Registers are readable and writable; the address es refer to the sam e register both in read and in writ e. In order to access the Configuration Register the user can work in several modes by utilizing the following instructions:
LDCI: loads the immediate value in the
Configuration Register specified and is the most commonly used to write configuration data.
LDCR: loads the Configuration Register
specified with the contents of the specified Register File location, allowing a parametric configuration.
LDCE: loads the Configuration Register
specified with the contents of the specified Program/Data Memory location, allowing the configuration data to be taken from a table.
LDCNF: loads the Register File location
specified with the c ontents of the Con figuration Register indicated, allowing for the inspection of the configuration of the device (permitting s afe run-time modifications).
In order to simplify the concept, a mnemonic name is assigned to each register. The same name is used in Visual FIVE devel opmen t tools. The list of the Configuration Registers is shown in Table 3.4.
25/106
ST52F510/F513/F514
Table 3.1 Input Registers
Mnemonic Description Address
PORT_A_IN Port A data Input Register 0 00h PORT_B_IN Port B data Input Register 1 01h PORT_C_IN Port C data Input Register 2 02h
- Not Used 3 03h
- Not Used 4 04h SPI_IN Serial Peripheral Interface data Input Register 5 05h
I2C_IN I2C_SR1 I2C_SR2
2
C Interface data Input Register
I
2
I
C Interface Status Register 1
2
I
C Interface Status Register 2
606h 707h 808h
- Not Used 9 09h
- Not Used 10 0Ah USP_H User Stack Pointer (MSB) 11 0Bh USP_L User Stack Pointer (LSB) 12 0Ch
- Not Used 13-2 0
0Dh-
014h PWM0_COUNT_IN_H PWM/Timer 0 Counter Input Register (MSB) 21 015h PWM0_COUNT_IN_L PWM/Timer 0 Counter Input Register (LSB) 22 016h PWM0_STATUS PWM/Timer 0 Status Register 23 017h PWM0_CAPTURE_H PWM/Timer 0 Capture Register (MSB) 24 018h PWM0_CAPTURE_L PWM/Timer 0 Capture Register (LSB) 25 019h PWM1_COUNT_IN_H PWM/Timer 1 Counter Input Register (MSB) 26 01Ah PWM1_COUNT_IN_L PWM/Timer 1 Counter Input Register (LSB) 27 01Bh PWM1_STATUS PWM/Timer 1 Status Register 28 01Ch PWM1_CAPTURE_H PWM/Timer 1 Capture Register (MSB) 29 01Dh PWM1_CAPTURE_L PWM/Timer 1 Capture Register (LSB) 30 01Eh
- Not Used 31-3 5
SCI_IN Serial Communication Interface RX data Input Register 36 024h SCI_STATUS Serial Communication Interface Status Register 37 025h FLAGS Flag Register 38 026h AD_OVF 10-bit A/D Converter Overflow Register 39 027h IAP_SR In Application Programming Status Register 40 028h
26/106
01Fh-
023h
ST52F510/F513/F514
Table 3.1 Input Registers
Mnemonic Description Address
CHAN0_H 10-bit A/D Converter Channel 0 data Input Register (MSB) 41 029h CHAN0_L 10-bit A/D Converter Channel 0 data Input Register (LSB) 42 02Ah CHAN1_H 10-bit A/D Converter Channel 1 data Input Register (MSB) 43 02Bh CHAN1_L 10-bit A/D Converter Channel 1 data Input Register (LSB) 44 02Ch CHAN2_H 10-bit A/D Converter Channel 2 data Input Register (MSB) 45 02Dh CHAN2_L 10-bit A/D Converter Channel 2 data Input Register (LSB) 46 02Eh CHAN3_H 10-bit A/D Converter Channel 3 data Input Register (MSB) 47 02Fh CHAN3_L 10-bit A/D Converter Channel 3 data Input Register (LSB) 48 030h CHAN4_H 10-bit A/D Converter Channel 4 data Input Register (MSB) 49 031h CHAN4_L 10-bit A/D Converter Channel 4 data Input Register (LSB) 50 032h CHAN5_H 10-bit A/D Converter Channel 5 data Input Register (MSB) 51 033h CHAN5_L 10-bit A/D Converter Channel 5 data Input Register (LSB) 52 034h CHAN6_H 10-bit A/D Converter Channel 6 data Input Register (MSB) 53 035h CHAN6_L 10-bit A/D Converter Channel 6 data Input Register (LSB) 54 036h CHAN7_H 10-bit A/D Converter Channel 7 data Input Register (MSB) 55 037h CHAN7_L 10-bit A/D Converter Channel 7 data Input Register (LSB) 56 038h
27/106
ST52F510/F513/F514
Table 3.2 Output Registers
Mnemonic Description Address
PORT_A_OUT Port A data Output Register 0 00h PORT_B_OUT Port B data Output Register 1 01h PORT_C_OUT Port C data Output Register 2 02h
- Not Used 3 03h
- Not Used 4 04h SPI_OUT Serial Peripher al Inte rfa ce data Outp ut Regis te r 5 05h
I2C_OUT PWM0_COUNT_OUT_H PWM/Timer 0 Counter Output Register (MSB) 7 07h
PWM0_COUNT_OUT_L PWM/Timer 0 Counter Output Register (LSB) 8 08h PWM0_RELOAD_H PWM/Timer 0 Reload Register (MSB) 9 09h PWM0_RELOAD_L PWM/Timer 0 Reload Register (LSB) 10 0Ah PWM1_COUNT_OUT_H PWM/Timer 1 Counter Output Register (MSB) 11 0Bh PWM1_COUNT_OUT_L PWM/Timer 1 Counter Output Register (LSB) 12 0Ch PWM1_RELOAD_H PWM/Timer 1 Reload Register (MSB) 13 0Dh PWM1_RELOAD_L PWM/Timer 1 Reload Register (LSB) 14 0Eh SCI_OUT Serial Communication Interface TX data Output Register 23 017h
2
C Interface data Output Register
I
606h
Table 3.3 Option Bytes
Mnemonic Description Address
OSC_CR Oscillator Control Register 0 00h CLK_SET Clock Parameters 1 01h OSC_SET Oscillator Set-Up 2 02h PLDV_CR Programmable Low Voltage Detector Control Register 3 03h WDT_EN HW/SW Watchdog selector 4 04h PG_LOCK First Page Write Protected 5 05h PG_UNLOCK First Page not Write Protected 6 06h WAKEUP Wake Up from Halt Time 7 07h
28/106
ST52F510/F513/F514
Table 3.4 Configuration Registers
Mnemonic Description Address
INT_MASK Interrupt Mask Register 0 00h INT_POL Interrupts Polarity 1 01h INT_PRL_H Interrupt Priority Reg ist er (hig he r priority ) 2 02h INT_PRL_M In te rru pt Pri orit y Regist er (me di um prior ity) 3 03h INT_PRL_L Interrupt Priority Register (lower prior ity) 4 04h
USTP_H User Stack Top Pointer (MSB) 5 05h USTP_L User Stack Top Pointer (LSB) 6 06h WDT_CR Watchdog Configurati on Re gis te r 7 07h AD_CR1 10-bit A/D Converter Control Register 1 8 08h PWM0_CR1 PWM/Timer 0 Configuration Register 1 9 09h PWM0_CR2 PWM/Timer 0 Configuration Register 2 10 0Ah
PWM0_CR3 PWM/Timer 0 Configuration Register 3 11 0Bh PWM1_CR1 PWM/Timer 1 Configuration Register 1 12 0Ch PWM1_CR2 PWM/Timer 1 Configuration Register 2 13 0Dh
- Not Used 14 0Eh
- Not Used 15 0Fh
I2C_CR
I2C_CCR
I2C_OAR1
I2C_OAR2
2
I
C Interface Control Register
2
I
C Interface Clock Control Register
2
I
C Interface Own Address Register 1
2
I
C Interface Own Address Register 2
16 010h
17 011h
18 012h
19 013h
SPI_CR Serial Peripheral Inte rfa ce Con trol Regi ste r 20 014h SPI_STATUS_CR Serial Peripheral Inte rfa ce Con trol-Status Register 21 015h SCI_CR1 Serial Communication Interface Control Register 1 22 016h SCI_CR2 Serial Communication Interface Control Register 2 23 017h PORT_A_PULLUP Port A Pull Up enable/disable Register 24 018h PORT_A_OR Port A Option Register 25 019h
29/106
ST52F510/F513/F514
Table 3.4 Configuration Registers
Mnemonic Description Address
PORT_A_DDR Port A Data Direction Register 26 01Ah PORT_A_AF Port A Alternate Function selection Register 27 01Bh PORT_B_PULLUP Port B Pull Up enable/disable Register 28 01Ch PORT_B_OR Port B Option Register 29 01Dh PORT_B_DDR Port B Data Direction Register 30 01Eh PORT_B_AF Port B Alternate Function selection Register 31 01Fh
PORT_C_PULLUP Port C Pull Up enable/disable Register 32 020h PORT_C_OR Port C Option Register 33 021h PORT_C_DDR Port C Data Direction Register 34 022h PORT_C_AF Port C Alternate Function selection Register 35 023h
- Not Used 36-4 2
SCI_CR3 Serial Communication Interface Control Register 3 43 02Bh SSP_H System Stack Pointer (MSB) 44 02Ch SSP_L System Stack Pointer (LSB) 45 02Dh CPU_CLK CPU Clock Prescaler 46 02Eh AD_CR2 10-bit A/D Converter Control Register 2 47 02Fh
024h-
02Ah
30/106
Loading...
+ 76 hidden pages