S.R.Smith Rogue 2 Assembly And Installation Instructions Manual
ASSEMBLY AND INSTALLATION INSTRUCTIONS
CORPORATE HEADQUARTERS
WESTERN SALES AND MANUFACTURING PLANT
P.O. Box 400 1017 SW Berg Parkway
Canby, Oregon 97013
(503) 266-2231 (503) 266-4334
www.srsmith.com
06-820 S.R. SMITH, LLC 2013 MAY14
2
Table of Contents
Topic Page #
INTRODUCTION ............................................................................................................................................................................ 2
ROGUE2 PARTS LIST ..................................................................................................................................................................... 3
TOOLS REQUIRED FOR SLIDE ASSEMBLY: .................................................................................................................................... 5
ASSEMBLY INSTRUCTIONS ........................................................................................................................................................... 7
ASSEMBLY INSTRUCTIONS FOR ON DECK MOUNTING .............................................................................................................. 13
IN-DECK MOUNTING .................................................................................................................................................................. 14
SLIDE PLUMBING INSTRUCTIONS .............................................................................................................................................. 14
MANUFACTURER’S PLACEMENT INSTRUCTIONS ....................................................................................................................... 16
ELECTRICAL BONDING................................................................................................................................................................ 18
Appendices: Left and Right CURVE FOOTPRINT......................................................................................................................... 19
INTRODUCTION
DANGER – FAILURE TO FOLLOW THESE WARNINGS, INSTRUCTIONS AND THE OWNER’S
MANUAL MAY RESULT IN SEROUS INJURY OR DEATH
THE ROGUE2 SLIDE IS DESIGNED AND MANUFACTURED FOR INSTALLATION AND USE ON INGROUND
SWIMMING POOLS ONLY. DO NOT INSTALL THE ROGUE2 SLIDE ON ABOVE GROUND POOLS,
HOUSEBOATS, BOAT DOCKS, FLOATING DOCKS OR PLATFORMS, OR OTHER BODIES OF WATER
SUCH AS LAKES, PONDS, RIVERS, ETC. PROPER ASSEMBLY, INSTALLATION, USE, AND SUPERVISION
IS ESSENTIAL FOR PROPER OPERATION AND TO REDUCE THE RISK OF SERIOUS INJURY OR DEATH.
CHECK INSIDE ALL BOXES AND PACKAGING MATERIALS FOR PARTS. BEFORE BEGINNING
ASSEMBLY, READ ALL INSTRUCTIONS AND IDENTIFY PARTS USING THE FIGURES AND PARTS LISTED
IN THIS DOCUMENT. IT IS CRITICAL THAT ALL PARTS BE CAREFULLY INSPECTED BY THE INSTALLER
PRIOR TO INSTALLATION TO ENSURE THAT NO DAMAGE OCCURRED IN TRANSIT AND THAT A
DAMAGED PART IS NOT USED. PROPER INSTALLATION CANNOT BE OVERSTRESSED, AS AN
IMPROPER INSTALLATION VOIDS S.R. SMITH’S WARRANTY AND MAY AFFECT THE SAFETY OF THE
USER.
INSTALLER MUST GIVE TO SLIDE OWNER: ROGUE2 SLIDE INSTALLATION AND OWNER’S MANUAL,
THE WARRANTY CARD, AND ANSWER ALL QUESTIIONS REGARDING SAFE AND PROPER USE AND
SLIDE MAINTENACE.
FOR COMPLETE SLIDE SAFETY INFORMATION REFER TO THE OWNER’S MANUAL.
INSTALLED ROGUE2 STRUCTURAL & INSTALLATION CHECKLIST (INSTALLER TO
REVIEW WITH SLIDE OWNER UPON COMPLETION OF SLIDE INSTALLATION)
1. INSPECT THE RUNWAY FOR VISIBLE CRACKS OR TEARS.
2. INSPECT THE SLIDE FOR SHARP EDGES, PROTRUSIONS, CRACKS OR TEARS.
3. INSPECT ALL FASTENERS TO MAKE SURE THEY ARE FULLY TIGHTENED.
4. INSPECT THE LADDER FOR RIGIDITY AND ATTACHMENT.
5. MEASURE THE FOLLOWING DIMENSIONS AND COMPARE WITH THE MANUFACTURER’S
PLACEMENT INSTRUCTIONS ON PAGES 17 AND 18.
MEASURE THE DEPTH OF WATER IN FRONT OF THE SLIDE EXIT. (4’-6” (1371 mm) MIN.
DEPTH AT A DISTANCE OF 4’-6” (1371 mm) FROM EXIT END OF SLIDE.)
MEASURE THE HEIGHT OF THE SLIDE RUNWAY EXIT ABOVE THE WATER. (20” (508 mm)
MAX.)
MEASURE THE DISTANCE BETWEEN THE SLIDE CENTERLINE AND THE EDGE OF
OTHER POOL EQUIPMENT.
6. OBSERVE THE POSITION OF THE EXIT OF THE SLIDE AS SHOWN IN FIGURES 17, 18 AND 19 ON
PAGES 17 AND 18.
3
ROGUE2 PARTS LIST
Ref # *
PART #
DESCRIPTION
QTY
1
05-773
Garden Hose Adapter (ref. pg 13)
1ea.
2
05-181
1” PVC 90 Elbow ST SCH 40 SXS
1 ea.
3
05-767
Plastic Pipe Clamp for 1” SCH 40
6 ea.
4
05-770
PVC Ball Valve SCH 80 SXS
1 ea.
5
05-31-151
¼-20 x 6” Carriage Bolt S/S
4 ea.
6
05-31-149
¼-20 x 8” Carriage Bolt S/S
2 ea.
7
01-212
Aluminum Handrail Spacer
6 ea.
8
6-123
Nylon Handrail Connector
8 ea.
9
6-121
Nylon Tube Connector
6 ea.
10
05-14-111
1/4 x 5/8 Flat Washer
13 ea.
11
5-149
¼” Lock Washer S/S
8 ea.
12
5-137
¼-20 Hex Nut S/S
8 ea.
13
01-210
Aluminum Ladder Spacer
2 ea.
14
5-237
3/8-16 X 5" B.H.C.S. 18-8 S/S FULL-THREAD (TT)
2 ea.
15
5-248
HHCS 3/8-16 X 3.5" S/S
2 ea.
16
5-250
3/8” x 3.5” Button Head Cap Screw S/S
4 ea.
17
5-145
3/8” Flat Washer S/S
16 ea.
18
5-151
3/8” Lock Washer S/S
8 ea.
19
5-139
3/8” Hex Nut S/S
4 ea.
20
5-156
3/8-16 ACORN NUT 316 S/S HIGH Crown
4 ea.
21
05-31-110S
5/16 Hex Washer Head Tek Screw S/S
4 ea.
22
5-371
Self Tapping Screw #10-16 x 1” S/S
6 ea.
23
05-668
Vinyl Cap .172 ID x .5 LG.
6 ea.
24
05-14-124
¼” X ½” Sheet Metal Screw
5 ea.
*
05-786-8
Hose PVC Flex, 8 ft (not shown in Figure 1)
8 ft.
Before getting started check to make sure that all of the parts listed below arrived with the S.R. Smith
ROGUE2 slide.
4
Figure 1
(24)
ROGUE2 PARTS
5
SLIDE DECK ANCHOR FLANGE KIT
(75-209-5866)
1
75-209-5000
Aluminum Flange Anchor
4 ea.
2
05-162
5/16 -18 UNC x 2 3/4 STUD w/ FLAT
WASHER & LOCK NUT
16 ea.
3
05-14-123
1/4-20 UNC x 2 3/4 HHCS
4 ea.
4
04-14-111
1/4"ID x 5/8"OD FLAT WASHER
8 ea.
5
05-14-117
1/4-20 UNC HEX NYLON LOCK NUT
4 ea.
6
01-500
3/8" O.D. ALUMINUM BUSHING
4 ea.
7
5-306
3/8” O.D. Aluminum Bushing
16 ea.
Figure 2
SLIDE DECK ANCHOR FLANGE KIT PARTS (SOLD SEPERATELY)
* Ref #s are shown as (#__ ) in these ASSEMBLY AND INSTALLATION INSTRUCTIONS
TOOLS REQUIRED FOR SLIDE ASSEMBLY:
PVC glue
7/32” Allen Wrench
Electric Drill, Phillips Drive, ½ Hex Socket Drive
Ratchet with 7/16”, 1/2" and 3/8” sockets
7/16”, 1/2” and 9/16” wrench
Hammer drill with 1/4" (6 mm) masonry bit
Small Level
Tape
9/16” Deep Socket
3/8” (9.5 mm) Drill Bit
¼” (6 mm) Drill bit
Pencil or marker
Loctite® 242 Thread Locking Compound
6
Figure 3
Note: When installing the slide in the
deck, all height dimensions will be
reduced by at least 3 inches, or by
the depth the slide is installed below
deck grade.
For SI: 1 degree = 0.017 rad, 1 inch = 25.4 mm, 1 foot = 304.8 mm
ROGUE2 SLIDE LAYOUT
The purpose of this footprint is to serve as a GUIDELINE ONLY for approximate placement of the slide relative to the pool’s
edge. The actual dimensions after installation may vary according to the slope of the deck and the angle that the slide is
oriented relative to the pool wall. YOU MUST FOLLOW THE INSTALLATION INSTRUCTIONS AS PRINTED IN
THIS MANUAL.
ROGUE 2 right curve slide shown, left curve is mirror image of right curve.
SEE APPENDICES (pg.17) for additional slide layout details.
Loading...