S.R.Smith pLX-PL60, pLX-PL100 Installation Instructions And Owner's Manual
poolLUX Plus
pLX-PL60 & pLX-PL100
Installation Instructions
Read all instructions before attempting to perform installation work
Type 3R Rainproof Enclosure
FOR USE WITH POOL AND SPA PRODUCTS
5005508
ETL LISTED
Conforms to UL STD 379;
Certied to CSA STD C22.2 #218.1
79-15264-00 Rev A
2
3
Contents
IMPORTANT SAFETY INFORMATION ................................4
RF Exposure Statement .................................................5
IC Statement.............................................................5
FCC WARNING .........................................................5
Electrical Ratings ........................................................6
Recommended Tools and Supplies ......................................6
INSTALLATION INSTRUCTIONS .......................................7
Enclosure mounting .....................................................7
Input / Supply Line Voltage ..............................................9
Output Wiring for Lights and Light Sources........................... 10
OPERATING INSTRUCTIONS ........................................ 12
Manual Rocker Switch Operation ..................................... 12
Wireless Remote Operation........................................... 13
WIRING DIAGRAM ................................................... 14
REPLACEMENT PARTS ...............................................15
4
IMPORTANT SAFETY INFORMATION
CAUTION: POWER AND SIGNAL OUTPUT CONDUITS MUST BE NON-METALLIC
ATTENTION: CONDUITS POUR PUISSANCE DE SORTIE ET SORTIE SIGNAL DOIT ETRE NON METALLIQUE
ELECTRICAL SHOCK HAZARD – SWITCH DOES NOT TURN OFF INPUT POWER.
Failure to disconnect input power before servicing can lead to serious injury, or death.
Disconnect input power before servicing.
Replace all parts and panels before reconnecting power and operating
DANGER – FAILURE TO FOLLOW THESE WARNINGS, INSTRUCTIONS, AND THE
OWNER’S MANUAL MAY RESULT IN SERIOUS INJURY OR DEATH.
Basic safety precautions shall be observed when installing and operating the poolLUX Plus
(p/n pLX-PL60/PL100) and other associated equipment:
1. A qualied electrician must install the poolLUX Plus (p/n pLX-PL60/PL100) in accordance with
the requirements of NEC ANSI/NFPA 70 and Article 680.
2. The poolLUX Plus (p/n pLX-PL60/PL100) must be mounted on a at vertical surface. The unit
must be a minimum of 4 inches above the ground level, pool deck, or higher than 8 inches
above the maximum pool water level, whichever provides greatest elevation. The unit must be
positioned a minimum of 4 feet (1.2 m) away from the inside wall of the pool, unless separated
from the pool by a solid fence, wall, or other permanent barrier.
3. CAUTION: THE EQUIPMENT AND CONTROLS SHALL BE LOCATED NOT LESS THAN
1 M HORIZONTALLY FROM THE SPA OR HOT TUB.
4. ATTENTION: MAINTENIR UNE DISTANCE MINIMALE, MESURÉE DANS UN PLAN
HORIZONTAL, DE 1 M ENTRE LA CUVE DE RELAXATION ET LES APPAREILS ET
COMMANDES.
5. ONLY USE COPPER CONDUCTORS.
6. Do not exceed the maximum electrical ratings of the poolLUX Plus (p/n pLX-PL60/PL100)
components (indicated on page 4), wiring devices, and current carrying capacity of the
conductors.
7. poolLUX Plus (p/n pLX-PL60/PL100) is intended to be used with low voltage underwater
luminaires that comply with Article 680 of the National Electrical Code and does not require
bonding due to their polymeric or isolated application design.
8. This device should never operate equipment that could cause property damage, bodily injury,
or death should it be activated unexpectedly.
9. Use with branch circuit breakers with 15 amperes or less.
10. This device must be used with an approved ground-fault circuit interrupter (GFCI).
11. Use rain-tight or wet location hubs that comply with the requirements in the standard (UL514b)
for conduit, tubing, and cable ttings only.
12. The conduit hub is to be connected to the power input conduit before the hub is connected to
the enclosure.
13. Never allow children to operate the pLX-Plus unit unsupervised.
5
RF Exposure Statement
IC Statement
FCC WARNING
To maintain compliance with FCC’s RF Exposure guidelines, this equipment should be installed
and operated with minimum distance of 20cm between the radiator and your body. Only use the
supplied antenna.
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to
the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
Le présentappareilestconforme aux CNR d’Industrie Canada applicables aux appareils radio
exempts de licence. L’exploitationestautorisée aux deux conditions suivantes:
(1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareildoit accepter
tout brouillageradioélectriquesubi, mêmesi le brouillageest susceptible d’encompromettre le
fonctionnement.
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
2. Changes or modications not expressly approved by S.R.Smith, LLC will void the user’s
authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment causes
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment on a different circuit than that of the receiver.
• Consult the dealer or an experienced Radio and Television Technician for help.
Loading...