Spirit XBR95 User Manual
Please carefully read this entire manual before operating your new tness bike
Fitness Bike
XBR95
OWNER’S MANUAL
Product Registration
Table of Contents
1
Important Safety Instructions
Important Electrical Instructions
XBR95
Product Features
Operation of Your Console
Programmable Features
Using A Heart Rate Transmitter
General Maintenance
Manufacturer’s Limited Warranty
Assembly Instructions
2
3
4
9
11
15
26
28
29
ATTENTION
This tness bike is intended for residential use only and is warranted for this
application. Any other application voids this warranty in its entirety.
XBR95
Fitness Bike
2
XBR95
Congratulations on your new tness bike and welcome to the Spirit Fitness family!
Thank you for your purchase of this quality group tness bike from Spirit Fitness. Your new
tness bike was manufactured by one of the leading tness manufacturers in the world and is
backed by one of the most comprehensive warranties available. Through your dealer, Spirit Fitness
will do all we can to make your ownership experience as pleasant as possible for many years to
come. If not purchased direct from Spirit Fitness, the local dealership where you purchased this
tness bike is your administrator for all Spirit Fitness warranty and service needs. Their responsibility is to provide you with the technical knowledge and service personnel to make your experience more informed and any difculties easier to remedy.
Please take a moment at this time to record the name of the dealer, their telephone number,
and the date of purchase below to make any future, needed contact easy. We appreciate your
support and we will always remember that you are the reason that we are in business. Please
complete and mail your registration card today and enjoy your new tness bike.
Product Registration
Yours in Health,
Spirit Fitness
Name of Dealer
Dealer Phone #
Purchase Date
Record Your Serial Number
Please record the serial number of this tness product
in the space provided below.
Serial Number
Register Your Purchase
The self-addressed product registration card must be completed in full and returned to Spirit
Fitness. You can also go to https://www.spirittness.com/residentialwarrantyregistration.html
to register online.
1
XBR95_20110623
Fitness Bike
XBR95
WARNING - Read all instructions before using this appliance.
Do not operate tness bike on deeply padded, plush or shag carpet. Damage to both carpet
and tness bike may result.
Keep children away from the tness bike. There are obvious pinch points and other
caution areas that can cause harm.
Keep hands away from all moving parts.
Never drop or insert any object into any openings.
Do not use outdoors.
Do not attempt to use your tness bike for any purpose other than for the purpose it is
intended.
The hand pulse sensors are not medical devices. Their purpose is to provide you with an ap-
proximate measurement in relation to your target heart rate. Use of a chest transmitter strap
is a much more accurate method of heart rate analysis . Various factors, including the user’s
movement, may affect the accuracy of heart rate readings. The pulse sensors are intended
only as exercise aids in
determining heart rate trends in general.
Wear proper shoes. High heels, dress shoes, sandals or bare feet are not suitable for use on
your tness bike. Quality athletic shoes are recommended to avoid leg fatigue.
SAVE THESE INSTRUCTIONS - THINK SAFETY!
Important Safety Instructions
Fitness Bike
2
XBR95
WARNING!
NEVER expose this tness bike to rain or moisture. This product is NOT designed for use
outdoors, near a pool or spa, or in any other high humidity environment. The operating
temperature specication is 40 to 120 degrees Fahrenheit, and humidity is 95%
non-condensing (no water drops forming on surfaces).
NEVER operate this tness bike without reading and completely understanding the
results of any operational change you request from the computer.
Understand that changes in resistance do not occur immediately. Set your
desired resistance level on the computer console and release the adjustment key.
The computer will obey the command gradually.
Use caution while participating in other activities while pedaling on your tness bike; such as
watching television, reading, etc. These distractions may cause you to lose
balance which may result in serious injury.
Do not use excessive pressure on console control keys. They are precision set to function
properly with little nger pressure.
Important Operation Instructions
3
Fitness Bike
XBR95
Assembly Video
To assist you in assembling your new Spirit Fitness tness bike, we have posted an assembly video at the
following link: http://www.spirittness.com/customerser vice/video/tnessbikevideos.html
Pre-Assembly
1. Using a razor knife (Box Cutter), cut the banding straps that wrap around the carton. Reach under the bottom
edge of the carton and pull it away from the cardboard underneath, separating the staples that join the two
together. Lift the box over the unit and unpack.
2. Carefully remove all parts from carton and inspect for any damage or missing parts. If damaged parts are
found, or parts are missing, contact your dealer immediately.
3. Locate the hardware package. The hardware is separated into four steps. Remove the tools rst. Remove the
hardware for each step as needed to avoid confusion. The numbers in the instructions that are in parenthesis
(#) are the item number from the assembly drawing for reference.
Assembly Tools
#114.Phillips Head
Assembly Instructions
Screwdriver
#115.L Allen Wrench
XBR95
#112.12/14mm
Wrench
Fitness Bike
#113.13/15mm
Wrench
4
#130.13/14mm
Wrench
XBR95
STEP 1: Rear Stabilizer & Seat Back
1. Attach the Rear Stabilizer (7) to the Main Frame (1) with the four Hex Head Bolts (65) and four Flat Washers
(84). Tighten completely with the wrench (112).
2. Attach the Seat Back (5) to the Seat Carriage (4) of the main frame. Slide a Hex Head Bolt (67) through each
side, then attach a Nyloc Nut (89) to each bolt. Tighten the bolts just enough so there is no side to side play, but
freedom of movement front to back. Use the wrenches provided (112 & 130).
HARDWARE
#89.3/8” x 7T
Nyloc Nut
(2 pcs)
#84.3/8” x 25 x 2T
Flat Washer
(4 pcs)
#65. 3/8” x 2-1/4”
Hex Head Bolt (4
pcs)
5
#67.3/8” x 4”
Hex Head Bolt
(2 pcs)
Fitness Bike
XBR95
STEP 2: Console Mast
1. Slide the Computer Cable (44), Handlebar resistance control cable (148), and Hand pulse cable (133) through
the bottom of the Console Mast Cover (31) and then the bottom of the Console Mast (2). Make sure the
Console Mast Cover is correctly oriented (see illustration).
2. Install the Console Mast (2) into the receiving tube (make sure not to pinch cables; damage to the electronics
could occur) of the Main Frame (1). Insert two Hex Head Bolts (68) and two Flat Washers (76) on each side.
Insert two Hex Head Bolts and two Curved Washers (83) on the front. Tighten all six bolts rmly with the
Wrench (112).
3. Remove the white Styrofoam pad (factory installed to prevent bolts from being accidentally dropped into the
console mast tube).
4. Attach the Handle Bar Assembly (3) onto the Console Mast (2) bracket with the two Hex Head Bolts (68),
two Split Washers (82), and two Flat Washers (76). Completely tighten with the wrench (112).
5. Insert the Computer Cable (44), Handlebar resistance control cable (148), and Hand Pulse Cable (133) into
their respective connectors in the back of the Console Assembly (19). Attach the
console onto the mounting plate with four Phillips Head Screws (99). Tighten with the Phillips Head Screw
Driver (114).
HARDWARE
#82.8 x 1.5T
Split Washer
(2 pcs)
#83.5/16” x 19 x 1.5T
Curved Washer
Fitness Bike
(2 pcs)
#76.5/16” x 18 x 1.5T
Flat Washer
(6 pcs)
6
#68.5/16” x 15mm Hex
Head Bolt
(8 pcs)
#99.M5 x 12mm
Phillips Head Screw
(4 pcs)
XBR95
STEP 3: Seat & Handle Bar
1. Install the Seat (61) on the Seat Carriage (4) with four Phillips Head Screws (98). Tighten with the Phillips Head
Screw Driver (114).
2. Attach the Seat Handle Bar (6) to the Seat Carriage (4) with the four Hex Head Bolts (71), four Flat Washers
(77), and four Nyloc Nuts (89). Tighten with the wrenches provided (112 & 130).
3. Plug the Hand Pulse Sensor Cables (27) into the rear two holes on the left side of the rear
plastic cover. Plug the Handlebar resistance cables (150) into the remaining front hole.
4. Attach the Front Stabilizer Cover (32) and the Rear Stabilizer Cover (37) to the Main Frame with four Phillips
Head Screws (99). Tighten with the Phillips Head Screw Driver (114).
HARDWARE
#98.M6 x 15mm
Phillips Head Screw
(4 pcs)
#89.3/8” x 7T
Nyloc Nut
(4 pcs)
#99.M5 x 12mm
Phillips Head Screw
(4 Pcs)
7
#77. 3/8” x 19 x 1.5T
Flat Washer
(4 Pcs)
#71. 3/8” x 1-3/4” Hex
Head Bolt
(4 Pcs)
Fitness Bike
Loading...