Spektrum SPMVS1100 User Manual

EN

SPMVS1100 / SPMVR1100 Instruction Manual

SPMVS1100 / SPMVR1100 Bedienungsanleitung

SPMVS1100 / SPMVR1100 Manuel d’utilisation

SPMVS1100 / SPMVR1100 Manuale di Istruzioni

1

EN

NOTICE

All instructions, warranties and other collateral documents are subject to change
at the sole discretion of Horizon Hobby, LLC. For up-to-date product literature, visit
horizonhobby.com and click on the support tab for this product.

Meaning of Special Language

The following terms are used throughout the product literature to indicate various
levels of potential harm when operating this product:

NOTICE: Procedures, which if not properly followed, create a possibility of physical
property damage AND a little or no possibility of injury.

CAUTION: Procedures, which if not properly followed, create the probability of
physical property damage AND a possibility of serious injury.

WARNING: Procedures, which if not properly followed, create the probability of
property damage, collateral damage, and serious injury OR create a high probability
of superficial injury.

WARNING: Read the ENTIRE instruction manual to become familiar with the
features of the product before operating. Failure to operate the product
correctly can result in damage to the product, personal property and cause
serious injury.

This is a sophisticated hobby product. It must be operated with caution and common
sense and requires some basic mechanical ability. Failure to operate this Product in a
safe and responsible manner could result in injury or damage to the product or other
property. This product is not intended for use by children without direct adult supervi­sion. Do not attempt disassembly, use with incompatible components or augment
product in any way without the approval of Horizon Hobby, LLC. This manual contains
instructions for safety, operation and maintenance. It is essential to read and follow
all the instructions and warnings in the manual, prior to assembly, setup or use, in
order to operate correctly and avoid damage or serious injury.

Age Recommendation: Not for children under 14 years. This is not a toy.
WARNING AGAINST COUNTERFEIT PRODUCTS

Thank you for purchasing a genuine Spektrum product. Always purchase from a
Horizon Hobby, LLC authorized dealer to ensure authentic high-quality Spektrum
product. Horizon Hobby, LLC disclaims all support and warranty with regards, but not
limited to, compatibility and performance of counterfeit products or products claiming
compatibility with DSM or Spektrum.

NOTICE: This product is only intended for use with unmanned, hobby-grade, remote­controlled vehicles and aircraft. Horizon Hobby disclaims all liability outside of the intended
purpose and will not provide warranty service related thereto.

WARRANTY REGISTRATION

Visit www.spektrumrc.com/registration today to register your product.

2

Box Contents

* Items not included with SPMVR1100

EN

Headset Carry Case

FPV Downlink Kit

(ultra micro camera and

video transmitter) *

5.8GHz Antenna

Teleporter Headset

Li-Po BATTERY PACK

7.4V 760mAh

7.4V 760mAh Li-Po

Battery w/Discharge

Adapter

ChargerY-Harness *

AV Cable*

Cleaning Cloth

3

EN

Li-Po BATTERY PACK

7.4V 760mAh

Li-Po BATTERY PACK

7.4V 760mAh

Li-Po BATTERY PACK

7.4V 760mAh

Teleporter Headset Functions

Antenna Connection

Channel Select

Brightness (left/right)

Data port

(head tracking)

Power Supply

Camera Functions

Digital head tracking

(push on/push off)

Contrast

(forward/back)

Volume

Display button

Receiver on/off

(video source select)

Headphone Jack

AV in/out

Antenna

Turn to Focus

Camera

Channel Select

4

Product Specifications:

Camera and Video Transmitter: (SPMVA1100)

Input power: 3.3–4.2V (1S supply)
Power consumption: 300mA @ 3.7V (1S)
Imager: 1/6” VGA CMOS
Camera Lens: 0.95mm IR cut
Field of view: 115°diagonal (90°horizontal)
Operating temp: -10º to 60ºC
Square: 13.2 X 17.6 X 9mm
Lens dimensions: 9mm X 10mm diameter
Antenna dimensions: 20mm X 25mm diameter
Video output: Analog NTSC video out
Frequency: 5.8GHz (7 channels available)
Weight: 4.5 g (with case)

Headset (SPMVS1100 Only):

Field of View: 25 deg diagonal
IPD distance: 63.5mm (fixed)
Input power: 7–13V (2S–3S Li-Po)
Battery: 7.4V 760mAh Li-Po battery with safety circuit (included)
Power consumption: 200/350mA (direct/wireless)
Video Receiver: 5.8GHz (7 channels available)
Weight: 163 g

CAUTION: Do not power the headset or downlink kit without the antenna
attached. Doing so will damage the transmitter and receiver amplifiers.

Amplifier damage is not covered by warranty.

EN

5

EN

Installation and Use

NOTICE: The downlink kit included with the Spektrum™ Ultra Micro FPV System

is designed for use in ultra micro airplanes, Helicopters and multi-rotors. Do not
attempt to use the downlink kit with larger aircraft. The FPV system is a low-power,
line of sight system.

Mounting the Downlink Kit

1. Select a mounting location on your aircraft that is close to the center of gravity and

will provide a point of reference, such as the landing gear or motor mount.

2. Apply double-sided foam tape to the downlink kit.

3. Secure the downlink kit to the fuselage. Keep the FPV downlink as far away from the

aircraft receiver as possible.

4. Make sure your video transmitter has a clean line of sight from the aircraft. Position

the antenna away from the fuselage.

NOTICE: Remove the lens cap before setting up and flight.

6

Powering the Downlink Kit
Option 1

• Connect a 1-cell (1S) Li-Po (not included) directly to the downlink kit.

1-cell (1S) Li-Po
(EFLB1501S45, EFLB1501S25)

Downlink kit

Option 2

• Using the included Y-harness, connect the downlink kit directly to the 1-cell (1S)

flight battery of your aircraft.

CAUTION: Always land the model before the battery reaches low voltage

cutoff (LVC), otherwise power will be lost to the receiver and camera.
Immediately land the model and disconnect the flight battery to prevent over­discharge. Never use the included Y-harness with sailplane models.

1-Cell (1S) Li-Po

Downlink Kit

EN

Receiver board

Y-Harness

To Downlink Kit

To Battery

To Receiver Board

7

EN

Charger Warnings

The battery charger included with your product has been designed to safely charge the
Li-Po battery.

CAUTION: All instructions and warnings must be followed exactly. Mishandling
of Li-Po batteries can result in a fire, personal injury and/or property damage.

• By handling, charging or using the included

Li-Po battery, you assume all risks associated
with lithium batteries.

• If at any time the battery begins to balloon

or swell, discontinue use immediately. If
charging or discharging, discontinue and
disconnect. Continuing to use, charge or
discharge a battery that is ballooning or
swelling can result in fire.

• Always store the battery at room

temperature in a dry area for best results.

• Always transport or temporarily store the

battery in a temperature range of 40–120º F
(5–49° C). Do not store the battery or model
in a car or direct sunlight. If stored in a hot
car, the battery can be damaged or even
catch fire.

• Always charge batteries away from

flammable materials.

• Always inspect the battery before charging.

• Always disconnect the battery after

charging, and let the charger cool between
charges.

Charging the Headset Battery Pack With Included Charger

1. Connect the charger to the wall outlet. The charger LED will be solid green.

2. Connect the battery to the charger. The charger LED will be solid red.

3. The charger LED is solid green when charging is complete.

4. Disconnect the battery from the charger and unplug the charger from the wall outlet.
CAUTION: If at any time during the charge process the battery pack

becomes hot to the touch, unplug the battery immediately and discontinue

the charge process.

Charging the Headset Battery Pack With Optional Chargers

1. Connect the Li-Po battery pack balance lead to your battery charger. If your battery

charger requires you to connect the battery power for charging, use the included
battery charge adapter.

2. Follow your battery charger instructions for charging a 7.4V 760mAh Li-Po battery.

• Always constantly monitor the temperature

of the battery pack while charging.

• ONLY USE A CHARGER SPECIFICALLY

DESIGNED TO CHARGE LI-PO BATTERIES.
Failure to charge the battery with a
compatible charger may cause a fire
resulting in personal injury and/or property
damage.

• Never discharge Li-Po cells to below 3V

under load.

• Never cover warning labels with hook and

loop strips.

• Never leave charging batteries unattended.

• Never charge batteries outside

recommended levels.

• Never charge damaged batteries.

• Never attempt to dismantle or alter the

charger.

• Never allow minors to charge battery

packs.

• Never charge batteries in extremely hot

or cold places (recommended between
40–120° F (5–49° C)) or place in direct
sunlight.

8

Using the Headset

CAUTION: Do not power the headset or downlink kit without the antenna

attached. Doing so will damage the transmitter and receiver amplifiers.

Amplifier damage is not covered under warranty.
NOTICE: Do not leave the headset exposed to direct sunlight. Sunlight is magnified by

the lens and will burn holes in the LCD color filter (appears as white open areas). LCD
damage is not covered under warranty.

Keep goggles in their protective case when not in use.

1. Attach the antenna to the headset.

2. Insert the battery into the slot on the right of the

headband. Insert the barrel connector on the fully
charged battery into the socket on the side of the
headset. The headset powers on when connected
and must be unplugged to turn it off.

3. Look through the headset and press the Channel Up/Down

buttons. Clean channels will have a consistent static background.
Channels with interference will display horizontal static lines. Select one of the clean
channels. A long beep sounds on channels 1 and 7.

4. Once you have chosen a clean channel in the

headset, select the same channel on the video
receiver.

• Press Left or Right on the Display Button to

adjust the video contrast in the headset.

• Press Forward or Back on the Display Button

to adjust the video brightness in the headset.

• Press Down on the Display Button to change

the video zoom in the headset. The normal
display shows the entire image. The zoom
display crops the image in the headset and is
used with digital head tracking.

Spektrum Ultra Micro
FPV Transmitter Channels

Channel 1 5470 MHz
Channel 2 5760 MHz
Channel 3 5780 MHz
Channel 4 5800 MHz
Channel 5 5820 MHz
Channel 6 5840 MHz
Channel 7 5860 MHz

EN

5. When the headset battery gets low, the headset will emit a beeping that gets

progressively more rapid as the battery voltage drops. Always land and recharge the
headset battery when you begin to hear the headset beep.

9

EN

Digital Head Tracking

• Long Press: Depressing the Display Button toggles head tracker mode
(active/deactivate). With digital head tracking active, the image will zoom in and
the image will digitally pan and tilt in response to head motion.

• Short Press: Resets center reference position (both analog/digital).

Analog Head Tracking

Analog head tracking output is always on.

• Connect the data cable to the data port on the headset and the trainer port on

you transmitter.

• Analog head tracking will allow a gimbal mounted camera to pan and tilt in

response to head motion.

Head Tracking Menu Navigation

Option part required to connect to your Spektrum transmitter (FSV1410).
To enter head tracking menu, hold the Display Button while inserting battery and

immediately release the button after barrel insertion.

Tip: Reversing pan/tilt direction will affect digital head tracking as well.

Beep code Mode

1 short beep: Pan/Tilt on ch 5/6
2 short beep: Pan/Tilt on ch 6/7
3 short beep: Pan/Tilt on ch 7/8
4 short beep: Reverse pan direction
5 short beep: Reverse tilt direction
1 long beep: Adjust servo center point*
1 short beep: Restore factory defaults
2 long beep: no selection made, automatically exits menu

* Press the Display Button to gain manual control of the camera with the headset.

To adjust the camera center position:

1. Move the headset to the desired camera center position.

2. Press the Display Button to save the new center position.
IMPORTANT: Make sure the servos are near the center point before adjusting the

camera center position, otherwise, the servo travel may be limited.

10

Flying with the Ultra Micro FPV System

Consult local laws and ordinances before operating FPV (first person view) equipment.
In some areas, FPV operation may be limited or prohibited. You are responsible for
operating this product in a legal and responsible manner.

1. Power on your radio transmitter, then power on the aircraft.

2. Remove lens cap from camera.

3. Power on the headset to make sure the channel is clear and then the video

transmitter.

4. Perform a range test before flying.

5. Fly in open areas, away from people, trees, cars, and buildings. The range of the

system can be impacted by any obstructions blocking your signal. It is normal to see
break up in the video going behind trees etc.

NOTICE: Do not use the ultra micro FPV system in low light or other instances where
visibility is restricted.

EN

11

EN

Li-Po BATTERY PACK

7.4V 760mAh

Li-Po BATTERY PACK

7.4V 760mAh

Caring for the Video Transmitter Antenna

If your video transmitter antenna gets bent
or fl attened as a consequence of a hard
landing, bend the antenna so the lobes are

45°

at a 45° angle to the bottom plane of the
antenna, as shown at the right.

Spektrum Ultra Micro FPV Troubleshooting

Problem Possible Cause Solution

No image, display is
completely dark

No image, display is
glowing dark gray

Static on all channels

Horizontal lines in the
headset display

Blurry Image Image is out of focus

No power supplied to
the video transmitter or
headset

Video source switch is set
to external receiver mode

Video transmitter power
is off

Digital interference on the
selected channel

Check the power
connections

Make sure the battery is
fully charged

Ensure the video source
switch is switched to
headset mode

Make sure the video
transmitter LED is on

Choose a cleaner channel

Rotate the lens slowly to
focus the camera

45°

12

1-YEAR LIMITED WARRANTY

What this Warranty Covers - Horizon Hobby, LLC, (Horizon) warrants to the original

purchaser that the product purchased (the “Product”) will be free from defects in materials
and workmanship for a period of 1 year from the date of purchase.
What is Not Covered - This warranty is not transferable and does not cover (i) cosmetic
damage, (ii) damage due to acts of God, accident, misuse, abuse, negligence, commercial
use, or due to improper use, installation, operation or maintenance, (iii) modification of or
to any part of the Product, (iv) attempted service by anyone other than a Horizon Hobby
authorized service center, (v) Product not purchased from an authorized Horizon dealer, or (vi)
Product not compliant with applicable technical regulations.
OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON MAKES NO OTHER WARRANTY
OR REPRESENTATION, AND HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES,
INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT,
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE PURCHASER
ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED THAT THE PRODUCT WILL
SUITABLY MEET THE REQUIREMENTS OF THE PURCHASER’S INTENDED USE.
Purchaser’s Remedy - Horizon’s sole obligation and purchaser’s sole and exclusive remedy
shall be that Horizon will, at its option, either (i) service, or (ii) replace, any Product determined
by Horizon to be defective. Horizon reserves the right to inspect any and all Product(s) involved
in a warranty claim. Service or replacement decisions are at the sole discretion of Horizon.
Proof of purchase is required for all warranty claims. SERVICE OR REPLACEMENT AS
PROVIDED UNDER THIS WARRANTY IS THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY.
Limitation of Liability - HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT,
INCIDENTAL OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR
COMMERCIAL LOSS IN ANY WAY, REGARDLESS OF WHETHER SUCH CLAIM IS BASED IN
CONTRACT, WARRANTY, TORT, NEGLIGENCE, STRICT LIABILITY OR ANY OTHER THEORY OF
LIABILITY, EVEN IF HORIZON HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Further, in no event shall the liability of Horizon exceed the individual price of the Product
on which liability is asserted. As Horizon has no control over use, setup, final assembly,
modification or misuse, no liability shall be assumed nor accepted for any resulting damage
or injury. By the act of use, setup or assembly, the user accepts all resulting liability. If you as
the purchaser or user are not prepared to accept the liability associated with the use of the
Product, purchaser is advised to return the Product immediately in new and unused condition
to the place of purchase.
Law - These terms are governed by Illinois law (without regard to conflict of law principals).
This warranty gives you specific legal rights, and you may also have other rights which vary
from state to state. Horizon reserves the right to change or modify this warranty at any time
without notice.

WARRANTY SERVICES
Questions, Assistance, and Services - Your local hobby store and/or place of

purchase cannot provide warranty support or service. Once assembly, setup or use of the
Product has been started, you must contact your local distributor or Horizon directly. This
will enable Horizon to better answer your questions and service you in the event that you
may need any assistance. For questions or assistance, please visit our website at www.
horizonhobby.com, submit a Product Support Inquiry at https://horizonhobby.quickbase.
com/db/bghj7ey8c?a=GenNewRecord, or call the toll free telephone number referenced
in the Warranty and Service Contact Information section to speak with a Product Support
representative.

13

EN

EN

Inspection or Services - If this Product needs to be inspected or serviced and is compliant
in the country you live and use the Product in, please use the Horizon Online Service Request
submission process found on our website or call Horizon to obtain a Return Merchandise
Authorization (RMA) number. Pack the Product securely using a shipping carton. Please note
that original boxes may be included, but are not designed to withstand the rigors of shipping
without additional protection. Ship via a carrier that provides tracking and insurance for lost
or damaged parcels, as Horizon is not responsible for merchandise until it arrives and is
accepted at our facility. An Online Service Request is available at http://www.horizonhobby.
com/content/_service-center_render-service-center. If you do not have internet access,
please contact Horizon Product Support to obtain a RMA number along with instructions for
submitting your product for service. When calling Horizon, you will be asked to provide your
complete name, street address, email address and phone number where you can be reached
during business hours. When sending product into Horizon, please include your RMA number,
a list of the included items, and a brief summary of the problem. A copy of your original sales
receipt must be included for warranty consideration. Be sure your name, address, and RMA
number are clearly written on the outside of the shipping carton.
Provided warranty conditions have been met, your Product will be serviced or replaced free of
charge. Service or replacement decisions are at the sole discretion of Horizon.

NOTICE: Do not ship LiPo batteries to Horizon. If you have any issue with a LiPo
battery, please contact the appropriate Horizon Product Support office. Warranty
Requirements- For Warranty consideration, you must include your original sales
receipt verifying the proof-of-purchase date.

Non-Warranty Service - Should your service not be covered by warranty, service
will be completed and payment will be required without notification or estimate
of the expense unless the expense exceeds 50% of the retail purchase cost. By

submitting the item for service you are agreeing to payment of the service without notification.
Service estimates are available upon request. You must include this request with your item
submitted for service. Non-warranty service estimates will be billed a minimum of ½ hour
of labor. In addition you will be billed for return freight. Horizon accepts money orders and
cashier’s checks, as well as Visa, MasterCard, American Express, and Discover cards. By
submitting any item to Horizon for service, you are agreeing to Horizon’s Terms and Conditions
found on our website http://www.horizonhobby.com/content/_service-center_render-service­center.

ATTENTION: Horizon service is limited to Product compliant in the country of
use and ownership. If received, a non-compliant Product will not be serviced.
Further, the sender will be responsible for arranging return shipment of the un­serviced Product, through a carrier of the sender’s choice and at the sender’s
expense. Horizon will hold non-compliant Product for a period of 60 days from
notification, after which it will be discarded.

14

Warranty and Service Contact Information

EN

Country of

Purchase

United States of

America

United Kingdom

Germany

France

China

Horizon Hobby Contact Information Address

Horizon Service Center

(Repairs and Repair

Requests)

Horizon Product

Support

(Product Technical

Assistance)

Sales

Service/Parts/Sales:

Horizon Hobby Limited

Horizon Technischer

Service

Sales: Horizon Hobby

GmbH

Service/Parts/Sales:
Horizon Hobby SAS

Service/Parts/Sales:

Horizon Hobby – China

servicecenter.horizonhobby.com/

RequestForm/

www.quickbase.com/db/

bghj7ey8c?a=GenNewRecord

888-959-2305

[e-mail]

888-959-2305

[e-mail]

[phone]

[e-mail]

[phone]

[e-mail]

[phone]

[e-mail]

[phone]

4105 Fieldstone Rd

Champaign, Illinois, 61822

Units 1–4, Ployters Rd,

Staple Tye, Harlow
Essex, CM18 7NS

United Kingdom

Christian-Junge-Straße 1

25337 Elmshorn, Germany

11 Rue Georges Charpak

77127 Lieusaint, France

Room 506, No. 97 Chang-

Shanghai, China 200060

USA

shou Rd.

FCC Information

This device complies with part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.

CAUTION: Changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to operate
the equipment.

This product contains a radio transmitter with wireless technology which has been tested and
found to be compliant with the applicable regulations governing a radio transmitter in the 5740
to 5860mHz frequency range.

IC Information

This device complies with Industry Canada license-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this device may not cause interference, and (2)
this device must accept any interference, including interference that may cause undesired
operation of the device.

15

EN

Compliance Information for the European Union

Declaration of Conformity (in accordance with ISO/IEC 17050-1)

No. HH2014100201
Product(s): FPV System - Ultra Micro

Item Number(s): SPMVS1100
The object of declaration described above is in conformity with the requirements of the

specifications listed below, following the provisions of the European R&TTE Directive
1999/5/EC, EMC Directive 2004/108/EC, and LVD Directive 2006/95/EC:

EN 300 440-1 V1.6.1
EN 300 440-2 V1.4.1
EN 301 489-1 V1.9.2: (2011-09)
EN 301 489-3 V1.6.1 (2013-08)

EN55022:2010 + AC:2011
EN55024:2010

EN 62479:2010
EN 60950-1:2006+A11:2009+A1:2010+A12: 2011

Signed for and on behalf of:
Horizon Hobby, LLC
Champaign, IL USA
October 2, 2014

Mike Dunne
Executive Vice President
Product Divisions
Horizon Hobby, LLC

16

Compliance Information for the European Union

Declaration of Conformity (in accordance with ISO/IEC 17050-1)

No. HH2014092903
Product(s): Teleporter V4 Video Headset

Item Number(s): SPMVR1100
The object of declaration described above is in conformity with the requirements of the

specifications listed below, following the provisions of the EMC Directive 2004/108/EC:

EN55022:2010 + AC:2011
EN55024:2010

Signed for and on behalf of:
Horizon Hobby, LLC
Champaign, IL USA
September 29, 2014

Instructions for disposal of WEEE by users in the European Union

This product must not be disposed of with other waste. Instead, it is the user’s
responsibility to dispose of their waste equipment by handing it over to a

designated collections point for the recycling of waste electrical and electronic
equipment. The separate collection and recycling of your waste equipment at the time
of disposal will help to conserve natural resources and ensure that it is recycled in a
manner that protects human health and the environment. For more information about
where you can drop off your waste equipment for recycling, please contact your local
city office, your household waste disposal service or where you purchased the product.

Mike Dunne
Executive Vice President
Product Divisions
Horizon Hobby, LLC

Replacement Parts / Ersatzteile / Pièces de rechange /
Pezzi di ricambio

Part # English Deutsch Français Italiano

SPMVG1100 Goggles Videobrille Lunettes Occhiali

SPMVA1100

FSV1701

FSV1410

FSV1802

SPMVX1100 Y harness Y-Kabel Cordon Y Prolunga a Y

FSV1807

FPV Ultra Micro
Camera

1000mAh 2 cell
headset battery

SPM/JR 1m HT
Data Cable

Universal Prong
Battery Charger

Replacement
rubber eye cups

FPV Ultra Micro
Kamera

1000mAh 2S
Headset Akku

SPM/JR 1m HT
Datenkabel

FSV Universal
Prong Akkulade­gerät

FSV Ersatz
Augen-Gummi­auflagen

Module Ultra
Micro FPV

Batterie 2S
1000mA pour
lunettes

Câble data SPM/
JR longueur 1m

Cordon adapta­teur de charge
universel

Œilletons en
caoutchouc de
remplacement

Videocamera

Batteria oc­chiali 1000mAh
2 celle

Cavo dati

Caricabatterie

Ricambio con­chiglie oculari
in gomma

Optional Parts / Diverse Teile / Pieces Optionnelles /
Pezzi Opzionali

Part # English Deutsch Français Italiano

FSV1805

EFLB1501S45

EFLB1501S25

Headset Diopter
Insert Kit

150mAh 1S

3.7V 45C LiPo

150mAh 1S

3.7V 25C LiPo

FSV Diopterein­sätze Headset

E-flite 150mAh
1S 3.7V 45C
LiPo Akku

E-flite 150mAh
1S 3.7V 45C
LiPo Akku

Kit de lentilles
correctrices

Batterie Li-Po
1S 150mA 45C

Batterie Li-Po
1S 150mA 25C

Kit inserto
diottrie per gli
occhiali FPV

150mAh 1S

3.7V 45C LiPo

150mAh 1S

3.7V 25C LiPo

© 2014 Horiz on Hobby, LLC.
DSM and t he Horizon Hobby logo are registe red trademarks o f Horizon Hobby, LL C.
The Spek trum trademar k is used with permis sion of Bachmann Industries, Inc.
All othe r trademarks, se rvice marks a nd logos are pro perty of the ir respective own ers.
Patents pending.

Create d 09/14 44906