Speed Queen UD13F126 Installation Operation Instruction

Roll Heated

Flatwork Finisher

325 mm (13 inch) Roll Models

Refer to Page 3 for Model Identification

Installation/Operation Supplement

Keep These Instructions for Future Reference.

(If this machine changes ownership, this manual must accompany machine.)

www.comlaundry.com

FWF1N

Part No. 1300567R2EN

December 2007

Installation/Operation Supplement

WARNING

FOR YOUR SAFETY, the information in this manual must be followed to minimize the risk of fire or explosion or to prevent property damage, personal injury or death.

• Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

• WHAT TO DO IF YOU SMELL GAS: – Do not try to light any appliance. – Do not touch any electrical switch; do not use any phone in your building. – Clear the room, building or area of all occupants. – Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s

instructions.

– If you cannot reach your gas supplier, call the fire department.

• Installation and service must be performed by a qualified installer, service agency or the gas supplier.

IMPORTANT: Purchaser must consult the local gas supplier for suggested instructions to be followed if the finisher operator smells gas. The gas utility instructions plus the SAFETY and WARNINGS note directly above must be posted in a prominent location near the finisher.

W033

W052

FOR YOUR SAFETY

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

W053

1300567 (EN)

1

Installation/Operation Supplement

Table of

Contents

Model Identification ........................................................................... 3

Safety Information.............................................................................. 4

Installation........................................................................................... 6

Overall Dimensions and Connecting Data ........................................... 7

Location Requirements......................................................................... 8

Lifting the Finisher ............................................................................... 8

Moving the Finisher with Rollers ......................................................... 9

Electrical Connection............................................................................ 11

Gas Connection..................................................................................... 12

Gas Technical Specifications........................................................... 13

Inlet Pressure.................................................................................... 13

Gas Conversion..................................................................................... 14

Adjustments and Flow Rates ........................................................... 14

Exhaust Requirements .......................................................................... 15

First Start-Up ........................................................................................ 16

Operation............................................................................................. 17

Operating Instructions for Microprocessor Models.............................. 17

Operating Controls........................................................................... 17

Pre-Operating Procedures ................................................................ 18

Operating Instructions...................................................................... 18

Operating Instructions for Electromechanical Models......................... 20

Operating Controls........................................................................... 20

Pre-Operating Procedures ................................................................ 21

Operating Instructions...................................................................... 21

Breakdown Procedures ......................................................................... 22

Alarms................................................................................................... 22

Insufficient Air Flow (Gas Models Only)........................................ 22

Emergency Safety Bar ..................................................................... 22

Thermal Warning Fan ...................................................................... 23

Speed Regulator Alarm.................................................................... 23

No Flame.......................................................................................... 23

Overheating or Sensor Not Connected ............................................ 23

Disposal of Unit................................................................................... 24

means without the expressed written consent of the publisher.

2

1300567 (EN)

Model Identification

Information in this manual is applicable to the following models:

UD13F063 UD13F078 UD13F079 UD13F126

Installation/Operation Supplement

1300567 (EN)

3

Installation/Operation Supplement

Safety Information

NOTE: This manual is only a supplement. Refer to Installation/Operation manual for full instructions.

WARNING

Electrical hazard inside.

Can cause death or serious injury.

Turn off and lockout/tag out all electrical power before opening.

WARNING

Moving parts hazard.

W536

Can cause serious injury.

Do not operate unless all guards and covers are in place.

Do not put hands/fingers beyond guard/ cover.

WARNING

Burn hazards.

Contact with machine components or hot goods can burn you.

Do not operate unless all guards are in place.

Use care when handling recently processed or dried goods.

W537

W538

4

Installation/Operation Supplement

WARNING

• Failure to install, maintain, and/or operate this machine according to the manufacturer’s instructions may result in conditions which can produce serious injury, death, and/or property damage.

• Do not repair or replace any part of the machine or attempt any servicing unless specifically recommended or published in this Installation/Operation Manual and that you are qualified to carry out.

• Whenever ground wires are removed during servicing, these ground wires must be reconnected to ensure that the machine is properly grounded and to reduce the risk of fire, electric shock, serious injury, or death.

W566

WARNING

Toxic and fire hazards.

Machine produces gases, fumes, and lint which may be toxic or catch fire and could result in serious injury or death.

Vent exhaust outdoors and regularly clean lint away from machine.

W539

WARNING

Burn and crash hazards.

Push red finger guard bar daily to test. If finisher does not stop, do not use.

Turn off and lockout/tag out all power until repaired.

W540

1300567 (EN)

5

Installation/Operation Supplement

Installation

NOTE: This manual is only a supplement. Refer to Installation/Operation manual for full instructions.

WARNING

IMPORTANT: Warranty is void unless the finisher is installed according to instructions in this manual. Installation should comply with minimum specifications and requirements detailed in this manual and applicable local gas fitting regulations, municipal building codes, water supply regulations, electrical wiring regulations, and any other relevant statutory regulations. Due to varied requirements, applicable local codes should be thoroughly understood and all pre-installation arranged accordingly.

To prevent fire, explosion, or personal injury, this finisher may only be installed, adjusted, and started up by a team of qualified technicians.

W543

It is strongly recommended that the purchaser be present during installation and the first tests.

6

Overall Dimensions and Connecting Data

Installation/Operation Supplement

500 mm

(19.68 in.)

Exhaust Duct

102 mm

(4 in.)

Model

UD13F063

2192 mm

(86 in.)

FRONT VIEW

Models

UD13F078

and UD13F079

2542 mm

(100.1 in.)

REAR VIEW

Exhaust Duct

102 mm

(4 in.)

Model

UD13F126

3910 mm

(154 in.)

500 mm

(19.68 in.)

1112 mm

(43.8 in.)

58 mm

(2.28 in.)

Gas Inlet and

Electric Inlet

60 mm

(2.36 in.)

TOP VIEW

100 mm

(3.94 in.)

70 mm

(2.76 in.)

130 mm

(5.12 in.)

542 mm

(21.34 in.)

Models UD13F063,

UD13F078 and

UD13F079

660 mm (26 in.)

Model UD13F126

860 mm (34 in.)

1300567 (EN)

Figure 1

FWF69N

7

Installation/Operation Supplement

Model Weight

UD13F063

UD13F078 and UD13F079

UD13F126

400 kg (882 lbs.)

420 kg (926 lbs.)

500 kg (1102 lbs.)

Location Requirements

NOTE: This manual is only a supplement. Refer to Installation/Operation manual for full instructions.

WARNING

To prevent fire, explosion, or personal injury, this finisher may only be installed, adjusted, and started up by a team of qualified technicians.

IMPORTANT: Transport finisher on skid until near area of desired installation. Reasonable care should be taken during installation.

Finisher is shipped with manual crank located on tray. Be certain to keep manual crank near machine for easy access.

.

To assure compliance, consult and adhere to building code requirements and comply with the following:

W543

Lifting the Finisher

NOTE: This manual is only a supplement. Refer to Installation/Operation manual for full instructions.

The finisher should be moved with a forklift as close as possible to the area where it will be installed.

IMPORTANT: DO NOT lift finisher with slings.

1. Position the forklift arms beneath the center of the unit (NOT toward either end) to lift the finisher at its center of gravity.

IMPORTANT: Lifting the finisher from either side could cause misalignment and/or damage to the finisher.

2. Adjust the forklift arms to their maximum length and width and insert them all the way under the center of the skid. Refer to Figure 2.

• The finisher must be installed in a very well

ventilated room (especially when using gas heating) with correct lighting and an ambient temperature in the range from 0

o

C (104°F).

+40

• The floor must at least be able to support

732 kg/m

2

(150 lbs./ft2) for the installation of the

o

C (32°F) to

finisher.

• The finisher MUST NOT be installed or stored in

an area where it will be exposed to water and/or weather.

Sufficient space must be left around the finisher to allow for its correct functioning.

• Allow at least 102 mm (4 inches) in the back to

allow for ventilation.

• Allow 813 mm (32 inches) on each side for

upkeep and maintenance.

• Allow sufficient space in front so that the

operator can work efficiently and safely.

FWF10N

Figure 2

8

1300567 (EN)

Installation/Operation Supplement

3. Use the forklift to carefully lift the packaged finisher. Refer to Figure 3.

IMPORTANT: DO NOT lift the unit more than 203 mm (8 inches) off the ground.

203 mm

8"

(8 in.)

FWF14N

Figure 3

4. Move the packaged unit as close as possible to the area where the finisher will be installed. Follow the procedures in Moving the Finisher with Rollers section.

Moving the Finisher with Rollers

NOTE: This manual is only a supplement. Refer to Installation/Operation manual for full instructions.

IMPORTANT: At least three people and three 89 mm (3.5 inch) to 102 mm (4 inch) rollers or pipes are required to move the finisher from the skid to its final location. Proper lifting and handling procedures must be followed to avoid damage to the finisher.

1. Remove the protective packing material.

2. Use a pry bar to remove the wood stops from the skid. Refer to Figure 4.

FWF13N

Figure 4

3. Remove the four shipping bolts from the bottom of the finisher.

IMPORTANT: To prevent damage to finisher DO NOT turn the finisher over or let it drop when handling.

1300567 (EN)

9

Installation/Operation Supplement

4. Place two rollers on the ground next to the finisher. Refer to Figure 5.

5. Place the third roller on the ground ahead of the first two rollers and past the end of the finisher.

6. Slowly lower the finisher off the skid and onto the first two rollers. Keep the unit level. Refer to

Figure 5.

IMPORTANT: DO NOT let go of the finisher at any point in the moving process.

NOTE: If the distance between the skid and the rollers is too far to move the finisher safely onto the rollers, make another “step” by placing blocks of wood between the skid and the rollers. Gradually step the finisher down onto the blocks of wood and then again onto the rollers.

7. Slowly roll the finisher forward. Refer to Figure 6.

FWF7N

Figure 6

8. Level the finisher.

Figure 5

FWF12N

10

1300567 (EN)

Installation/Operation Supplement

Electrical Connection

IMPORTANT: Electrical specifications in Tab les 1 and 2 are subject to change without notice. Always

Electrical connections should be made by a qualified electrical contractor in accordance with all applicable

refer to product serial plate for most current specifications of product being installed.

local and national requirements. A differential circuit breaker (obtain locally), correctly sized for the power consumption of the finisher, must be installed near finisher. Refer to Ta b les 1 and 2 for cable diameter.

Electric Models

Serial Plate Rating Model Wire Size Breaker Size Full Load Amps

UD13F063 3 x 10 AWG

208/240/60/3*

UD13F078 3 x 10 AWG

UD13F063 4 x 6 AWG

230/50/3

UD13F078 4 x 6 AWG

UD13F063 5 x 16 AWG

400/50/3

UD13F078 5 x 16 AWG

NOTE: Use copper conductors only.

NOTE: Connect to individual branch circuit.

70 49

80 61

60 42

70 53

35 26

45 33

(3 x 10 mm

(4 x 10 mm

(5 x 4 mm

(5 x 6 mm

2

)

2

)

2

)

2

)

2

)

2

)

Serial Plate Rating Wire Size Breaker Size Full Load Amps

120/60/1

208/240/60/1**

230/50/3

400/50/3

* Electric models: For areas with 440/480/60/3 electrical

requirement, install 208/240/60/3 finisher and use a remote transformer (obtain locally).

3 x 14 AWG

(3 x 2.5 mm

3 x 14 AWG

(3 x 2.5 mm

3 x 14 AWG

(3 x 2.5 mm

5 x 14 AWG

(5 x 2.5 mm

Table 1

Gas Models

2

)

2

)

2

)

2

)

Table 2

** Gas models: For areas with 440/480/60/3 electrical

15 7.5 (Model UD13F126)

4.8 (All other Models)

15 4.8

10 4.8

10 4.2

requirement, install 208/240/60/1 finisher and use a remote transformer (obtain locally).

1300567 (EN)

11

Installation/Operation Supplement

Gas Connection

NOTE: This manual is only a supplement. Refer to Installation/Operation manual for full instructions.

IMPORTANT: The installation must comply with local codes or, in the absence of local codes, with the current National Fuel Gas Code, ANSI Z223.1 in the U.S.A., or the current CAN/CSA B149, Installation Codes in Canada.

Install a shut-off valve to isolate gas connections from rest of installation. Gas models must be connected to the existing gas pipes. The gas supply pipe size must have sufficient dimensions to minimize pressure loss. Obtain specific gas supply pipe size from the gas supplier. Refer to Tab l e 3 for general pipe size.

Gas Pipe Size Required for 1000 Btu Natural Gas — 0.64 Specific Gravity

at 17.4 ± 4 mbar, 1.74 ± 0.37 kPa (7 ± 1.5 inches) Water Column Pressure

Gas

Appliances

Total Btu/hr

100,000 120,000 140,000 160,000 180,000 200,000 300,000 400,000 500,000 600,000 700,000 800,000 900,000

1,000,000

7.63 m

(25 feet)

19.05 (0.75)

25.40 (1)

31.75 (1.25)

38.10 (1.5)

50.80 (2)

15.25 m

(50 feet)

Based on 0.3 in. Water Column Pressure Drop for Length Given

Sizes shown in mm (inches)

19.05 (0.75)

25.40 (1)

31.75 (1.25)

38.10 (1.5)

50.80 (2)

31.75 (1.25)

38.10 (1.5)

When connecting to a gas line, an equipment shut-off valve must be installed within 1.8 m (6 feet) of the finisher. A 1/8 inch NPT pipe plug must be installed as shown. Refer to Figure 7.

IMPORTANT: Be certain finisher is configured for type of gas being used. Refer to Gas Conversion section for additional information.

Equivalent Length

22.88 m (75 feet)

25.40 (1)

50.80 (2)

30.50 m

(100 feet)

25.40 (1)

31.75 (1.25)

38.10 (1.5)

50.80 (2)

63.50 (2.5)

38.13 m

(125 feet)

25.40 (1)

31.75 (1.25)

38.10 (1.5)

50.80 (2)

63.50 (2.5)

45.75 m

(150 feet)

25.40 (1)

31.75 (1.25)

38.10 (1.5)

50.80 (2)

63.50 (2.5)

12

Tab le 3

1300567 (EN)

Gas Technical Specifications

Installation/Operation Supplement

Country

DE I2ELL G20 20

AT/DK/FI/IT/

SE

IE/PT/GB/GR II2H3P G20 20

CH/ES II2H3P G20 20

BE I2E+ G20 20

FR II2Esi3P G20 20

LU II2E3P G20 20

NL II2L3P G25 25

Gas

Category

I3P G31 50

I2H G20 20

I3P G31 37

Gas

Designation

G25 20

G31 37

G31 37 and 50

G25 25

G31 37 and 50

G31 50

Pressure

Table 4

Inlet Pressure

(mbar)

1

2

5

4

1 New Stainless Steel Flexible Connector –

Use only if allowed by local codes (Use Design A.G.A. Certified Connector)

2 1/8 in. NPT Pipe Plug

(For checking inlet gas pressure)

3 Equipment Shut-Off Valve – Installed within

1.8 m (6 ft.) of finisher

4 Black Iron Pipe 5 1 inch Gas Connection

3

D233I

Use a manometer to verify that the inlet pressure meets the following requirements:

Natural Gas service must be supplied at 7.0 ± 1.5 inch water column pressure (1.74 ± 0.37 kPa).

L.P. (Liquefied Petroleum) Gas service must be supplied at 11 ± 0.3 inch water column pressure (2.74 ± 0.07 kPa).

Figure 7

1300567 (EN)

13

Installation/Operation Supplement

Gas Conversion

NOTE: This manual is only a supplement. Refer to Installation/Operation manual for full instructions.

NOTE: DO NOT connect the finisher to L.P. Gas Service without converting the gas valve. An L.P. Gas Conversion kit must be installed by the Manufacturer’s Authorized Dealers, Distributors, or qualified service personnel.

NOTE: Instructions for installing gas conversion kit can be found inside left frame of finisher.

Adjustments and Flow Rates

Gas Type G20 G25

Model

Manifold Pressure 20 20 25

Injector Orifice Size

Air Adjustment “d”

Burner flow rate cu.

3

m

/h (ft3/h)

Input kW (BTUH)

Gas Type G31

Model

Manifold Pressure 37 50

Injector Orifice Size

Air Adjustment “d”

Burner flow rate cu.

3

/h (ft3/h)

m

Input kW (BTUH)

UD13F063

3.5 mm

(0.138 in.)

4 mm

(0.157 in.)

2.4

(84.76)

22.5

(76842)

UD13F063

2.4 mm

(0.094 in.)

18 mm

(0.709 in.)

1.7

(60.03)

22.5

(78642)

UD13F078

and

UD13F079

4 mm

(0.157 in.)

4 mm

(0.157 in.)

3.2

(113)

30

(102455)35(120000)

UD13F078

and

UD13F079

2.7 mm

(0.106 in.)

18 mm

(0.709 in.)

2.3

(81.22)

30

(102455)35(120000)

UD13F126 UD13F063

4.4 mm

(0.173 in.)

18 mm

(0.708 in.)

3.7

(130.66)

UD13F126 UD13F063

2.9 mm

(0.114 in.)

18 mm

(0.709 in.)

2.7

(95.34)

3.9 mm

(0.154 in.)

(98.88)

22.5

(76842)30(102455)35(120000)

2.3 mm

(0.091 in.)

18 mm

(0.709 in.)

(60.03)

22.5

(78642)30(102455)

UD13F078

and

UD13F079

4.5 mm

(0.178 in.)

0 0 18 mm

2.8 (130.66)

UD13F078

and

UD13F079

2.5 mm

(0.098 in.)

18 mm

(0.709 in.)

1.7

(81.22)

UD13F126 UD13F063

4.8 mm

(0.188 in.)

(0.708 in.)

3.7

2.3

4.3

(151.85)

UD13F078

UD13F079

3.6 mm

(0.142 in.)

000

2.8

(98.88)

22.5

(78642)30(102455)35(120000)

4.2 mm

(0.165 in.)

(130.66)

and

3.7

UD13F126

4.4 mm

(0.173 in.)

4.3

(151.85)

14

Tab le 5

1300567 (EN)

Installation/Operation Supplement

Exhaust Requirements

NOTE: This manual is only a supplement. Refer to Installation/Operation manual for full instructions.

WARNING

Finisher produces combustible lint. To reduce the risk of fire, the finisher must be exhausted to the outdoors.

To reduce the risk of fire and accumulation of combustible gases, DO NOT exhaust finisher air into a window well, gas vent, chimney or enclosed, unventilated area such as an attic wall, ceiling, crawl space under a building, or concealed space of a building.

W545

IMPORTANT: Provisions must be made for makeup air.

NOTE: At a minimum, the National Fuel Gas Code requires finishers to have at least 6.5 sq. cm (one square inch) of opening for every 1000 Btu/hr. of input rating for proper combustion.

IMPORTANT: Do not obstruct flow of combustion and ventilation air.

The air flow necessary for combustion is shown in Tab l e 6.

Type UD13F063 UD13F079 UD13F126

Cfm 2 x 292* 2 x 292 2 x 292

Table 6

*One motor on electric models.

Using the shortest possible path, connect the exhaust outlet to an outlet duct. For gas models, use two separate outlets that are at least 102 mm (4 inches) each or use a single outlet duct that has a diameter of at least 152 mm (6 inches).

IMPORTANT: Outlet ducts used for the finisher’s exhaust may under no circumstances be shared with other devices.

WHERE THE EXHAUST DUCT PIERCES THE WALL OR CEILING, AN OPENING HAVING A DIAMETER FOUR INCHES LARGER THAN THE DIAMETER OF THE EXHAUST DUCT SHALL BE PROVIDED, AND THE EXHAUST DUCT CENTERED WITHIN THE OPENING.

51 mm

(2 in.)

MINIMUM

CLEARANCE

51 mm

(2 in.)

MINIMUM

CLEARANCE

NO SCREEN OR CAP

AIR OUT

762 mm (30 in.) MINIMUM CLEARANCE

51 mm (2 in.) MINIMUM

CLEARANCE

WALL

180°

SWEEP ELBOW

CEILING

51 mm (2 in.) MINIMUM CLEARANCE

Figure 8

254 mm

(10 in.)

803 mm

(31.62 in.)

178 mm

(7 in.)

FWF83N

1300567 (EN)

15

Installation/Operation Supplement

First Start-Up

1. Verify that the finisher is stable and level.

2. Check that all connections and exhausts are correctly established.

3. Check that the finisher is properly grounded.

4. Remove wax paper from cylinder, if applicable.

5. Inspect thermostat holder and make sure it is touching cylinder. Refer to Thermostat Inspection section.

6. Check that all controls are in position 0 (OFF) and that the speed regulator knob is set to the minimum position.

7. Turn the circuit breaker to position 1 (ON).

8. On electromechanical models, press the green Power On button and hold for 1 to 2 seconds.

On microprocessor models, press START keypad.

9. Check that the exhaust fans are rotating in the direction indicated by the arrows shown on the exhaust fans. If exhaust fans are rotating in wrong direction, the electrical connection at L1, L2 or L3 terminals must be changed.

11. Place all panels back on the finisher.

12. Turn the heat switch to position 1 (ON).

13. Check that the temperature of the finisher rises.

14. Adjust the temperature selection knob according to the type of fabric and dampness level of the material being ironed.

15. When the ironing cylinder reaches the selected temperature and the heat indicator light turns off, proceed to perform an ironing test.

NOTE: The cylinder is coated with wax when leaving the factory, so perform a first ironing test using worn linen.

16. Place the worn linen flat on the input tray and allow it to be pulled into the finisher by the feeding ribbons.

17. Adjust the speed by turning the speed regulator knob left to reduce speed or right to increase speed.

18. Make sure that the sample linen comes out completely dry and with a perfect sheen. If it doesn’t, either increase the temperature or reduce the ironing speed.

IMPORTANT: Finisher will not heat if exhaust fans are not rotating in proper direction.

10. Check that the feeding ribbons are rotating in the direction toward the interior of the finisher.

IMPORTANT: Take care not to touch or go near a moving part.

16

1300567 (EN)

Operating Instructions for Microprocessor Models

Operating Controls

Installation/Operation Supplement

Operation

WARNING

To avoid serious injury BEFORE operating flatwork finisher, ALL personnel MUST be trained on safe operation.

8

7

6

5

4

3

2

_

SET

+

0

000

_

SPEED

SET

+

W546

SPEED

13

WARNING

To avoid possible serious injury, ALWAYS read and become familiar with operating instructions before operating flatwork finisher.

9

10

11

12

14

15

16

17

W547

18

19

1

1 Left Side of Finisher 11 Decrease Ironing Speed Keypad 2 Control Panel 12 START Keypad 3 Left Exhaust Outlet 13 Finger Guard Safety Panel 4 Stop Keypad 14 Feeding Ribbons 5 Increase Preset Temperature Keypad 15 Return Ribbons 6 Decrease Preset Temperature Keypad 16 Right Exhaust Outlet 7 Display Preset Temperature Keypad 17 Input Tray 8 Temperature Display 18 Output Tray 9 Speed Display 19 Right Side of Finisher

10 Increase Ironing Speed Keypad

Figure 9

FWF58N

1300567 (EN)

17

Installation/Operation Supplement

Pre-Operating Procedures

NOTE: All maintenance must always be carried out when the machine is stopped, the cylinder is cold, and the circuit breaker is turned off.

Perform the following procedures daily before starting the finisher.

1. Inspect the area between the thermostat and the cylinder by gently pressing on the thermostat holder so the thermostat lifts up.

2. Clean area if debris is present.

3. Check that the thermostat holder touches the cylinder.

Operating Instructions

To identify the finisher’s controls, refer to Figure 9.

IMPORTANT: The flatwork finishers are for professional use and must be operated by qualified personnel.

1. Perform Pre-Operating Procedures.

2. Press START keypad. Indicators will light, current temperature and preset speed will be displayed, blower fan starts, cylinder rotates, and after 15 seconds, the finisher will begin to heat.

3. Check that the feeding ribbons are rotating in direction toward interior of finisher.

4. Check the operation of the finger guard safety panel by touching the panel. If finisher does not stop, press STOP keypad, discontinue use and call a qualified service person.

6. Choose an ironing speed between 1 and 7 by pressing either the increase ironing speed or decrease ironing speed keypads. The current speed is displayed in the speed display. The current speed does not need to be reset after power failure.

When finisher is started, if the preset speed is set between 1 and 7, the cylinder will rotate at speed 1, regardless of the preset speed, while the detected temperature remains below the preheat operating temperature (130°C [266°F] by default). Once the preheat operating temperature has been reached, the preset speed will be activated. If the temperature drops below the preheat operating temperature during operation, the speed will readjust to speed 1.

NOTE: To perfectly dry and put sheen on the laundry, the speed must be adjusted according to the type of fabric and dampness level of the material being ironed.

7. View preset temperature by pressing SET keypad. Adjust temperature by pressing increase preset temperature keypad or decrease preset temperature keypad according to the type of fabric and dampness level of the material being ironed. The new temperature is stored after three seconds.

Temperature display will then display current temperature. The maximum temperature value is established by the manufacturer.

NOTE: On electric models, the heat will turn on and off while finisher is heating.

5. Press START keypad.

18

1300567 (EN)

Installation/Operation Supplement

8. View temperature display. For best performance, begin ironing a few degrees before preset temperature is reached (for example, if preset temperature is 176°C [350°F], begin ironing at 173°C [345°F]). Refer to Installation/Operation manual for information on heating the cylinder.

IMPORTANT: The working temperature varies depending on the fabric being ironed but must never exceed a constant temperature of 180°C (356°F).

9. Place the linen flat on the input tray and allow it to be automatically pulled into the finisher by the feeding ribbons. Refer to Installation/Operation manual for information on adjusting tension of the feeding and return ribbons.

10. When the work is almost completed, press the STOP keypad. Finisher will stop automatically when the temperature of the cylinder is less or equal to the programmed stop temperature (default is 80

o

C [176oF]).

IMPORTANT: Never remove power from the machine when the temperature is equal to or higher than 80°C (176°F). This may cause damage to the feeding and return ribbons. Refer to Breakdown Procedures section for steps required when power failure occurs.

IMPORTANT: When ironing smaller sized articles, make sure to work along the length of the finisher, maintaining a consistent usage of each of the return ribbons. Doing this will prolong the life of the return ribbons.

11. Remove the finished linen from the output tray.

12. Hang or fold ironed linen as soon as possible to preserve finish.

IMPORTANT: Do not leave damp linen in the finisher as this will cause the cylinder to rust.

1300567 (EN)

19

Installation/Operation Supplement

Operating Instructions for Electromechanical Models

Operating Controls

WARNING

To avoid serious injury BEFORE operating flatwork finisher, ALL personnel MUST be trained on safe operation.

6

5

4

170˚

125˚

3

7

75˚

W546

10

WARNING

To avoid possible serious injury, ALWAYS read and become familiar with operating instructions before operating flatwork finisher.

8

9

13

11

12

W547

2

1

1 Left Side of Finisher 9 Speed Regulator Knob 2 Control Panel 10 Finger Guard Safety Panel 3 Left Exhaust Outlet 11 Feeding Ribbons 4 Temperature Selection Knob 12 Return Ribbons 5 Heat Indicator Light 13 Right Exhaust Outlet 6 Power Off Button 14 Input Tray 7 Power On Button 15 Output Tray 8 Heat Switch 16 Right Side of Finisher

15

Figure 10

14

16

FWF3N

20

1300567 (EN)

Installation/Operation Supplement

Pre-Operating Procedures

NOTE: All maintenance must always be carried out when the machine is stopped, the cylinder is cold, and the circuit breaker is turned off.

Perform the following procedures daily before starting the finisher.

1. Inspect the area between the thermostat and the cylinder by gently pressing on the thermostat holder so the thermostat lifts up.

2. Clean area if debris is present.

3. Check that the thermostat holder touches the cylinder.

Operating Instructions

To identify the finisher’s controls, refer to Figure 10.

IMPORTANT: The flatwork finishers are for professional use and must be operated by qualified personnel.

1. Perform Pre-Operating Procedures.

2. Check that all controls are in position 0 (OFF), and that the speed regulator knob is set to the minimum position.

3. Turn the circuit breaker to position 1 (ON).

4. Press the green Power On button and hold down for 1 to 2 seconds.

5. Check that the feeding ribbons are rotating in direction toward interior of finisher.

6. Check the operation of the finger guard safety panel by touching the panel. If finisher does not stop, press Power Off button, discontinue use and call a qualified service person.

7. Press the green Power On button and hold down for 1 to 2 seconds.

8. Turn the heat switch to position 1 (ON).

9. Adjust the temperature selection knob according to the type of fabric and dampness level of the material being ironed.

IMPORTANT: The working temperature varies depending on the fabric being ironed but must never exceed a constant temperature of 180°C (356°F).

11. Place the linen flat on the input tray and allow it to be automatically pulled into the finisher by the feeding ribbons. Refer to Installation/Operation manual for information on adjusting tension of the feeding and return ribbons.

12. Turn the speed regulator knob left to reduce speed or right to increase speed.

• Left = Reduce Speed

• Right = Increase Speed

NOTE: To perfectly dry and put sheen on the laundry, the speed must be adjusted according to the type of fabric and dampness level of the material being ironed.

13. When the work is almost completed, turn the heat switch to position 0 (OFF) about 20 minutes before finishing ironing to allow the cylinder to cool gradually. Once the ironing has been completed, allow the finisher to continue to run for about 20 to 30 minutes to allow the finisher to dry.

IMPORTANT: Never stop the machine when the temperature is equal to or higher than 80°C (176°F). This may cause damage to the feeding and return ribbons.

IMPORTANT: When ironing smaller sized articles, make sure to work along the length of the finisher, maintaining a consistent usage of each of the return ribbons. Doing this will prolong the life of the return ribbons.

14. Remove the finished linen from the output tray.

15. Hang or fold ironed linen as soon as possible to preserve finish.

IMPORTANT: Do not leave damp linen in the finisher, as this will cause the cylinder to rust.

16. Press the red Power Off button to shut down the finisher.

Mark 1: from 100°C (212°F) to 130°C (266°F) Mark 2: from 130°C (266°F) to 160°C (320°F) Mark 3: from 160°C (320°F) to 180°C (356°F)

10. Wait until the ironing cylinder reaches a temperature close to the selected temperature. The heat indicator light turns off when the required temperature is reached.

1300567 (EN)

21

Installation/Operation Supplement

Breakdown Procedures

Hot Finisher Stops Due to Power Failure

To separate the return ribbons from cylinder immediately:

1. Insert the crank into the opening located on the right panel of the finisher.

2. Turn the crank clockwise to rotate the cylinder. Refer to Figure 11.

3. Insert a thick and very wet cloth (hardly wrung dry) into the finisher while rotating the cylinder with the crank.

Alarms

(Microprocessor Models Only)

An alarm will sound for abnormal conditions as shown below.

Insufficient Air Flow (Gas Models Only)

When the pressure valve in the exhaust pipe opens for two seconds or more, the alarm sounds for one minute and display shows AL1.

On 3-Phase models, check the rotation direction of the exhaust fans. If exhaust fans are rotating in wrong direction, the electrical connection at L1, L2 or L3 terminals must be changed. If exhaust fans are rotating in correct direction, disconnect gas exhaust pipe. If alarm stops, exhaust pipe is too narrow or blocked.

Alarm is cancelled automatically when pressure switch returns to normal position or when finisher is turned off.

Emergency Safety Bar

WARNING

NOTE: Side panel is removed for illustrative

FWF11N

purposes only. NEVER operate unit without side panels.

FWF11N

Figure 11

Finisher Won’t Start or Stops Suddenly

If the finisher won’t start and the cylinder won’t rotate or has stopped suddenly, check if finger guard safety panels or manual crank safety switch are activated. Release the activated emergency stops, and immediately start the finisher again by pressing the green Power On button to prevent damage to return ribbons.

Unusual Noises and Other Issues

If the finisher makes unusual noises (rubbing, banging, etc.), or for any other problem contact a qualified service person immediately.

Emergency safety bar is for your safety. To avoid serious personal injury, do not override emergency safety bar.

W548

When the emergency safety bar is activated, the finisher automatically turns off, the alarm sounds for one minute and display shows AL2.

Alarm is cancelled by moving emergency safety bar to normal position and restarting finisher or turning machine off and on.

22

1300567 (EN)

Installation/Operation Supplement

Thermal Warning Fan

When the thermal relay of the fan is activated, the alarm sounds for one minute and display shows AL4. The fan and heating are switched off and finisher remains on. This alarm is usually caused by dirt on the fan.

Alarm is automatically cancelled when the thermal relay is closed or finisher is turned off.

Speed Regulator Alarm

When the speed regulator alarm is activated, the alarm sounds for one minute and display shows AL5.

Finisher will automatically turn off. This fault condition may be due to an overload of the cylinder motor caused by a thick object inside the finisher or by dirt in the cylinder motor.

Alarm is cancelled by restarting finisher or turning finisher on and off.

No Flame

When the burner is on or being ignited and a no flame condition occurs, the alarm sounds for one minute and display shows AL6.

Overheating or Sensor Not Connected

If the temperature sensor is broken, not connected or if sensor detects a temperature above 210°C (410°F) continuously for two seconds, the alarm sounds for one minute and display shows AL7. The finisher will continue to operate.

Alarm can be cancelled by turning finisher off.

The command for ignition remains active and the finisher remains on.

When the gas device cancels the fault indication, the alarm stops.

To try to re-ignite the burner, press the Decrease Preset Temperature keypad and Increase Preset Temperature keypad simultaneously after alarm stops.

If the reset fails, the alarm is activated again and one of the following fault conditions occurs:

• No gas supply. Check that the manual valve of

gas supply is open.

• Gas pressure is insufficient or incorrect gas type

is being used (refer to Gas Connection section).

• Ignition electrode is faulty. Replace ignition

electrode.

To cancel alarm without re-igniting burner, press Stop keypad to stop finisher.

1300567 (EN)

23

Installation/Operation Supplement

Disposal of Unit

This appliance is marked according to the European directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE).

This symbol on the product or on its packaging indicates that this product shall not be treated as household waste. Refer to Figure 12. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. Ensuring this product is disposed of correctly will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product. The recycling of materials will help to conserve natural resources. For more detailed information about recycling of this product, please contact the local city office, household waste disposal service, or the source from which the product was purchased.

MIX1N

Figure 12

24

Speed Queen UD13F126 Installation Operation Instruction

Specifications and Main Features

Frequently Asked Questions

User Manual