SpeeCo SplitMaster 40151000, SplitMaster 401510CA Owner's Manual

10 TON HORIZONTAL LOG SPLITTER

MODEL NO. 40151000 & 401510CA

Owner’s Manual

ASSEMBLY & OPERATING INSTRUCTIONS

This safety alert symbol identifies important safety messages in this manual.
Failure to follow this important safety information may result in serious injury
or death.

LS112-794-0810
Rev. 2

Table of Contents

Page(s)

Important Safety Information................................................................................................................. 1-6

Intended Use ......................................................................................................................... 1

Personal Protective Equipment ............................................................................................... 1

Safety Decals ....................................................................................................................... 1-2

General Safety ...................................................................................................................... 3

Preparation of the Log ........................................................................................................... 3

Work Area ........................................................................................................................... 3

Operation of the Log Splitter ................................................................................................. . 3-4

Repair and Maintenance Safety ............................................................................................. 4

Hydraulic Safety .................................................................................................................. 5

Fire Prevention ..................................................................................................................... 5-6

T owing Safety ................................................................................................................. ..... 6

Assembly Instructions ...................................................................................................................... 7

Operating Instructions ....................................................................................................................... 7-9

Engine Oil Recommendations ................................................................................................ 8

Hydraulic Oil Recommendations.............................................................................................. 8

St arting Instructions ............................................................................................................... 8

T owing ........................................................................................................................ .......... 9

Operation .............................................................................................................................. 9

Maintenance ..................................................................................................................................... 9

Parts List .............................................................................................................................................. 10-11

Parts Breakdown Illustration .............................................................................................................. 10-13

Notes ....................................................................... ................................................................................ 14

Specifications ................................................................................................................ ....................... Back Cover

WARNING: Read and thoroughly understand all instructions and safety information before
assembling or operating this log splitter. Failure to do so may cause serious injury or death. Do not
allow anyone to operate this log splitter who has not read this manual. As with all power equipment, a
log splitter can be dangerous if assembled or used improperly. Do not operate this log splitter if you
have doubts or questions concerning safe operation. Call our customer service department at

1-800-525-8322 to address these concerns.

Si no entiende ingles, se prefiere que busque alguien que interprete las instrucciones para usted.

INTENDED USE

NEVER use this log splitter for any other purposes than splitting wood. It is designed for this use only. Any other use can

cause serious injury or death.

PEPER

PERSONAL PROTECTIVE EQUIPMENT

PERPERSONALSONAL PROTECTIVE EQUIPMENT

BEFORE operating this log splitter make sure that you wear safety gear such as goggles or safey glasses, steel toed

shoes and tight fitting gloves (without loose cuffs or draw strings). Always wear a protective hearing device when operat­ing this log splitter.

NEVER wear loose clothing or jewelry that can be caught by moving parts of the log splitter. Keep clothing and hair away
from all moving parts when operating this log splitter.

SAFETY DECALS

Make sure that all safety warning decals are in good condition and readable. Always replace missing or defaced decals.
Write us or call 1-800-525-8322 and they will be sent to you at no charge.

DL-52-8

DL52-2-8

PART NUMBER: 52061000
LOCATION: HYDRAULIC CYLINDER

Page 1

PART NUMBER: 52060700
LOCATION: FRONT OF TONGUE

PART NUMBER: 52055200
LOCATION: BOTH SIDES OF RAM

Page 2

GENERAL SAFETY

Failure to follow these instructions may result in serious injury or death.

EVER

NEVER allow children to operate this log splitter. NEVER allow adults lacking proper instructions and understanding to

operate this log splitter.
KEEP all people and pets a minimum of 10 feet away from your work area when operating this log splitter. Only the

operator is to be near the log splitter during use.

NEVER actuate the control until everyone is clear of the work area.
NEVER operate the log splitter when under the influence of alcohol, drugs or medication.
NEVER allow a person who is tired or otherwise not alert to use your log splitter.

PREPARATION OF THE LOG

Both ends of the log should be cut square to help prevent the log from riding out of the splitter during
operation. Do not split logs greater than 18 in. in length.

WORK AREA

WORK AREA

NEVER operate the log splitter on slippery, wet, muddy or icy ground.
ONLY operate your log splitter on level ground. Operating on a slope could cause the log splitter to roll over or logs to fall

off.
NEVER operate your log splitter in an enclosed area. Exhaust fumes contain carbon monoxide which can be deadly when

inhaled.

NEVER attempt to move your log splitter over hilly or uneven terrain without a tow vehicle or adequate help.
ALWAYS block the wheels to prevent movement of the log splitter while in operation.
ONLY operate your log splitter in daylight or under good artificial light.
ALWAYS keep the work area clean. Remove split wood around your log splitter immediately so that you don’t stumble

over it.

OPERATION OF THE LOG SPLITTER

ONLY operate the log splitter from the operator zone as

shown in the diagram. The operator has the safest and
most effcient access to the control valve and the beam
in this location.Failure to operate the log splitter in this
position can result in serious injury or death.

Page 3

KNOW how to stop the log splitter and disengage the controls before operating it.
NEVER place hands or feet between the log and splitting wedge during forward or reverse stroke. Serious injury or death

could result.

NEVER straddle or step over the log splitter during operation.
NEVER reach or bend over the log splitter to pick up a log.
NEVER try to split two logs on top of each other.
NEVER try to cross split a log.
NEVER attempt to load your log splitter when the ram or wedge is in motion.
ALWAYS use your hand to operate the control lever on the valve. NEVER use your foot, a rope or any extension device.
NEVER move the log splitter while the engine is running. Shut off the engine even if you are leaving the log splitter for a

short period of time.
ALWAYS avoid contact with the muffler and other hot areas of the engine during operation or after running to prevent

burns.

REPAIR AND MAINTENANCE SAFETY

NEVER operate your log splitter when it is in poor mechanical condition or in need of repair.

Periodically check that all nuts, bolts, screws, hydraulic fittings and hose clamps are tight.
NEVER alter your log splitter in any manner. Such alterations may cause your log splitter to be unsafe and will void the

warranty.
Perform all recommended maintenance procedures before using your log splitter.
Replace all damaged or worn parts immediately.
NEVER tamper with the engine to run it at excessive speeds. The maximum engine speed is preset by the manufacturer

and is within safety limits. See engine manual.

ALWAYS remove the spark plug wire before performing any service or repair on your log splitter.
ALWAYS check the level of hydraulic oil and engine oil before operation.
ALL replacement parts must meet manufacturer’s specifications.

Page 4

HYDRAULIC SAFETY

The hydraulic system of your log splitter requires careful inspection along with the mechanical parts. Be sure to
replace frayed, kinked, cracked or otherwise damaged hydraulic hoses or hydraulic components.

NEVER check for leaks of hydraulic fluid with your hand. Fluid escaping from a small hole can be almost invisible.
Escaping fluid under pressure can have sufficient force to penetrate skin causing serious personal injury or even death.
Leaks can be detected by passing a piece of cardboard over the suspected leak and looking for discoloration.

ALWAYS seek professional medical attention immediately if injured by escaping hydraulic fluid. Serious infection or
reaction can develop if proper medical treatment is not administered immediately.

ALWAYS be sure to relieve all pressure by shutting off the engine and moving the valve control handle back and forth
should it become necessary to loosen or remove any hydraulic fitting.

NEVER remove the cap from the hydraulic tank or reservoir while the log splitter is running. Tank could contain hot oil
under pressure that could result in serious injury.

NEVER adjust the hydraulic valve. The pressure relief valve on your log splitter is preset at the factory. Only a qualified
service technician should perform this adjustment.

FIRE PREVENTION

NEVER operate your log splitter near a flame or spark. Hydraulic oil and gasoline are flammable and can explode.
NEVER fill the gas tank while the engine is hot or running. Allow the engine to cool before refueling.
NEVER smoke while operating or refueling your log splitter. Gas fumes can easily explode.
ONLY refuel your log splitter in a clear area with no gas fumes or spilled gas.
ALWAYS use an approved fuel container.
ALWAYS replace the gas cap securely.

If gasoline has spilled, move the log splitter away from the area of the spill and avoid creating any source of ignition until
the spilled gas has evaporated.

ALWAYS take a Class B fire extinguisher with you when operating this log splitter in dry areas as a precautionary
measure against possible flying sparks.

ALWAYS drain the fuel tank prior to storage to avoid the potential fire hazard.
ALWAYS store gasoline in an approved, tightly sealed container. Store the container in a cool, dry place.
NEVER store gasoline in the house or near a heating appliance.

Page 5

IMPORTANT NOTE:

This log splitter is equipped with an internal combustion engine and should not be used on or near any unimproved forest­covered, brush-covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester
meeting applicable local or state laws (if any). If a spark arrester is used, it should be maintained in efffective working
order by the operator. In the state of California a spark arrester is required by law. Other states have similar laws. Federal
laws apply on federal lands. A spark arrester muffler (optional by manufacturer) is available as an accessory at your
nearest engine dealer. Always check the legal requirements in your area.

TOWING SAFETY

nNEVER tow this log splitter on a road or highway. Serious injury and/or damage could result.This log splitter may be

towed off road behind an ATV or lawn tractor. Low speed towing is strongly recommended.

NEVER carry any cargo or wood on your log splitter.
NEVER allow anyone to sit or ride on your log splitter.
ALWAYS disconnect your log splitter from the towing vehicle before operating it.
ALWAYS be careful when backing up with your log splitter in tow. It could jackknife.
ALWAYS allow for added length of your log splitter when turning, parking, crossing interesections and in all driving

situations.

Page 6

IMPORTANT NOTICE

We, the manufacturer, reserve the right to change the product and/or specifications in this manual without notification.
The manual is for information usage only and the pictures and drawings depicted herein are for reference only.

ASSEMBLY INSTRUCTIONS

NOTE: This log splitter was partially assembled at the factory. Refer to the drawing and parts list should it become necessary to

disassemble the unit for repair or replacement of parts.

STEP 1: Remove all the components from the crate. Inspect each piece for shipping damage. If any part is damaged, contact your dealer or

delivering carrier.

STEP 2: Refer to the beam assembly drawing Illustration 2. Remove the bolts (22) and then move the tongue (21) to the desired position on the

beam (1).Securely attach with the two 3/8” x 3-1/2” bolts (22) and 3/8” hex nuts (23). Tighten.

STEP 3: Refer to the general assembly drawing illustration 1.Using the four 7/16” x 1-1/2” bolts (8) and nuts (10), attach the beam assembly to the

axle/frame assembly (1). Tighten.

STEP 4: Refer to the general assembly drawing illustration 1. Mount the wheels (2) to the axle/frame (1) using the 3/4” washers (4) and 1/8” x 1”

cotter pins (3).

STEP 5: Refer to the general assembly diagram illustration 1. Attach the tongue stand (7) to the tongue using the lock pin (5).
STEP 6: Refer to general assembly diagram illustration 1. Attach the engine (14) to the frame assembly (1) using the four 5/16” x 1-1/2”

bolts (6) and the four 5/16” hex nuts (9).

STEP 7: Refer to beam assembly drawing Illustration 2. Remove the bolts (13) and the cylinder retainers (14). Slide the cylinder (8) into the working

position and securely fasten the cylinder retainers (14) using the two 5/16” x 5/8” bolts (13).

STEP 8: Connect the suction line (18) in beam assembly illustration 2 to the elbow (6) on the pump (5). See engine assembly illustration 3.

Secure with the hose clamp (16) as shown in illustration 2. Attach the pressure hose (9) coming from the pump (5) in illustration 3 to the
valve (6) as shown in illustration 2.

STEP 9: Fill the tank by inserting a funnel into the return line (15). See Illustration 2. Fill with approximately 2 gallons of hydraulic fluid until the fluid

level is visible in the clear line with the tank level. AW46 hydraulic oil is recommended. Automatic transmission fluid can be substituted and
should be used when temperatures are below 32° F. Use only clean oil and take care to prevent dirt from entering the hydraulic reservoir.

STEP 10: Attach the return line (12) as shown in illustration 1 to the valve (6) as shown in illustration 2 and secure with hose clamp (16) from the

hardware kit.

STEP 11: Add oil to the engine and fuel to the gas tank. See Engine Oil Recommendations on the following page.Refer to the engine owner’s

manual for more information.

STEP 12: Start the engine and then cycle the cylinder by pushing on the valve handle to remove air from the system.
STEP 13: Turn off the engine. Cycle the valve handle to relieve pressure and then disconnect the return line at the valve. Add approximately 1/2

galllon of hydraulic fluid until the fluid level is visible in the clear line with the tank level.

STEP 14: Reconnect the return line to the valve (6). Secure with a hose clamp (17) and tighten.

OPERATING INSTRUCTIONS

WARNING: Read and thoroughly understand all instructions and safety information before operating
this log splitter. Failure to do so may cause serious injury or death. Do not allow anyone to operate
this log splitter who has not read this manual. As with all power equipment, a log splitter can be
dangerous if assembled or used improperly. Do not operate this log splitter if you have doubts or
questions concerning safe operation. Call our customer service department at 1-800-525-8322 to

address these concerns.
Si no entiende ingles, se prefiere que busque alguien que interprete las instrucciones para usted.

Page 7

CAUTION: DO NOT START OR RUN THE ENGINE BEFORE ADDING OIL IN THE HYDRAULIC RESERVOIR AND OIL IN

THE ENGINE.

ENGINE OIL RECOMMENDATIONS

Use 4-stroke automotive detergent oil. SAE 10W-30 is recommended for general use. Refer to the SAE Viscosity Grades chart on page 17 of your
engine owner’s manual for average temperature ranges. The engine manufacturer recommends using API SERVICE Category SE or SF oil.
The engine oil capacity is 0.63 US qt. (0.6 L).
Always check oil level before starting the engine. Keep oil level at full.

STARTING INSTRUCTIONS

NOTE: REFER TO THE ENGINE OWNER’S MANUAL FOR COMPLETE INFORMATION ON STARTING, MAINTENANCE AND TROUBLE­ SHOOTING.

1) Move the fuel valve lever to the ON position.

2) To start a cold engine, move the choke lever to the CLOSE position.
To restart a warm engine, leave the choke lever in the OPEN position.

3) Move the throttle lever away from the SLOW position, about 1/3 of the way toward the FAST position.

4) Turn the engine switch to the ON position.

5) Pull the starter grip until you feel resistance, then pull briskly. Return the starter grip gently.

6) If the choke lever has been moved to the CLOSE position to start the engine, gradually move it to the OPEN position as the engine
warms up.

7) To stop the engine in an emergency, simply turn the engine switch to the OFF position. Under normal conditions, move the throttle lever
to the SLOW position and then turn the engine switch to the OFF position. Then turn the fuel valve lever to the OFF position.

For further information on starting and stopping the engine, refer to your engine owner’s manual.

NOTE: The engine maximum governed speed is preset at the factory at 3600 RPM no load speed. When splitting wood, the throttle should be

set at the maximum setting to develop the horsepower required for the pump.

Page 8

OPERATION

WARNING: See safety information related to operation of the log splitter on page 3 and 4 of this manual. Make sure that you have the
recommended personal protective equipment described on page 1.

1) Set up the log splitter in a clear, level area and block the wheels. Make sure that the suction port on the tank is always on the lower side
of the log splitter.

2) Place a log on the beam against the wedge. Make sure the the log is securely on the beam and up against the wedge.

3) With the engine running, depress the valve handle so that the cylinder will drive the ram into the log. Extend the cylinder until the log splits or
to the end of its stroke. If the log has not completely split after the cylinder has reached the end of its extension, retract the cylinder.

IMPORTANT: Leaving the valve in the “actuate” position at the end of the stroke may damage the pump. Always use extra care

when splitting logs with unsquare ends.

TOWING
NEVER tow this log splitter on a road or highway. Serious injury and/or damage could result.This log splitter may be

towed off road behind an ATV or lawn tractor. Low speed towing is strongly recommended.

MAINTENANCE

1) Consult the operating and maintenance instructions of the engine manufacturer for engine care and maintenance.

2) Always check the oil level of the hydraulic reservoir before operation. Operating the log splitter without an adequate oil supply will cause
severe damage to the pump.

3) Clean the suction filter after the first 25 hours of operation. Thereafter, clean the filter every 100 hours or seasonally, whichever comes first.

4) To drain the hydraulic oil from the tank, loosen the hose clamp (11) and remove suction hose (12). Refer to illustration 1 on page 10. We
recomend that the suction filter (19) as shown in illustration 2 on page 11 be removed and cleaned at this time.

5) If excessive clearance is found between the push plate (3) to beam mount, loosen push plate bolts and adjust the middle plate to approximately
1/8 in. gap on each side. Retighten bolts securely. Do not adjust plate too tightly or damage may result. Refer to illustration 2.

6) See also Repair and Maintenance Safety on page 4 of this manual.

7) All replacement parts must meet manufacturer’s specifications.

Page 9

12

MODEL NO. 40151000 LOG SPLITTER

Illustration 1

11

13

14

8

12

6

11

5

7

9

10

1

2

3

4

Reference Part No. Description Quantity
No.

1 40127800 Frame/Axle 1

2 40035500 Tire 2
3 O/L 1/8” x 1” Cotter Pin 2
4 O/L 3/4” Washer 2
5 07096700 Lock Pin 1
6 O/L 5/16” x 1-1/2” Hex Cap Bolt 4
7 40128000 Ground Stand 1
8 O/L 7/16” x 1-1/2” Hex Cap Bolt 4
9 O/L 5/16” Nut 4
10 O/L 7/16” Nut 4
11 39031600 Hose Clamp 2
12 39038200 Suction Hose and Return Hose 2
13 39026100 Pressure Hose 1
14 39053900 6.5 HP SpeeCo Engine 1

Page 10

MODEL NO. 40151000 LOG SPLITTER

11

6

15

16

17

17

20

19

16

9

12

9

5

10

8

7

3

13

14

4

2

23

22

1

21

Illustration 2

18

Reference Part No. Description Quantity
No.

1 40128100 Tank/beam 1

2 O/L 3/8” Nylock Nut 1
3 40128300 Push Plate 1
4 O/L 3/8” x 2-1/2” Hex Cap Bolt 1
5 39039100 Swivel Elbow, 3/4”, 1/2” 1
6 390410C0 Auto-Return Valve 1
7 39034300 1/2”-1/2” Hex Nipple 1
8 39013300 2-3/4” x 18” Cylinder 1
9 39031100 3/4 in. NPTF -1/2 in. NPTF Reducer Bushing 2
10 39026100 Pressure Hose 1
11 39032400 3/4”x 45° Elbow 2
12 39038000 Hydraulic Cylinder Tubing 1
13 O/L 5/16” x 5/8” Hex Cap Bolt 4
14 40128500 Cylinder Retainer 2
15 39038200 3/4” x16” Return Hose 1
16 39031600 Hose Clamp 2

17 39032000 3/4” NPT-3/4” Tube 90° 2
18 39038200 3/4” x 16” Suction Hose 1
19 39090200 Suction Filter 1
20 40128900 Breather Tube 1
21 40127900 Tongue 1
22 O/L 3/8” x 3-1/2” Bolt 2
23 O/L 3/8” Nut 2

Page 11

Reference Part Number Description Qty.
No.

1 O/L 5/16”-18 UNC Nylock Nut 4
2 O/L 5/16” x 1-1/4 Grade 5 Bolt 4
3 O/L M8 x 1.25 x 20mm Bolt 4
4 39026100 Pressure Hose 1
5 39053900 196 cc Engine 1
6 39071800 2.5 GPM Pump 1
7 40034800 3/16” x 1” Square Key 1

8 40081200 Pump Mount 1
9 400833L0 Law Coupler, 1/2” Bore 1
10 400834L0 Spider for Jaw Coupler 1
11 400835L0 Jaw Coupler, 3/4” Bore 1

Illustration 3

Engine/Pump Assembly

Page 12

NOTE: Some of the 40151000 log splitters are equipped with the pump shown below.
Please make a visual identification of your pump before ordering replacement parts or
calling for service.

Illustration 3

1

7

3

5

8

9

4

Reference Part No. Description Quantity
No.

1 39053900 6.5 HP Speeco Engine 1

2 O/L M9 x 1,25 x 29MM Bolt 4
3 40085400 Pump Mount 1
4 O/L M7x 20 Allen Screw 4
5 39071600 Pump 1
6 39039200 3/8” NPT to 3/4” 90° Elbow 1
7 40085500 Coupler 1
8 40034800 Engine Key 1
9 39027700 Pressure Hose 1

6

2

Engine/Pump Assembly

Page 13

IMPORTANT NOTICE

We, the manufacturer, reserve the right to change the product and/or specifications in this manual without notification.
The manual is for information usage only and the pictures and drawings depicted herein are for reference only.

NOTES

Model No. ____________________ Serial No. _____________________________
Date of Purchase _______________ Place of Purchase _______________________

_______________________
_______________________
_______________________

Page 14

SPECIFICATIONS

00015104.ONLEDOM

GNITTILPSMUMIXAM

ECROF

ENIGNE

REDNILYC

EVLAV

PMUP

HTGNELGOLMUMIXAM

*EMITELCYC

SLEEHW

EGDEW

CMAEB

YTICAPAC

EZISELDAR

CILUARDYHLATOT

snoT01

oCeepSPH5.6

ekortS"81xretemaiD"57.2

nruteR-otuA

egatSelgniS

"81

hgiH"5

"57.6

snollaG5.2

MPG5.2

sdnoceS91

seriTfruTcitamuenPdeepSwoL

THGIEH

HTGNEL

HTDIW

THGIEWGNIPPIHS

epmet

"56

"43

.

sbl042

nognidnepedyravlliwemitelcyclautcA.emitelcycesaclaedI*

.cte,ycneiciffepmup,deepsenigne,edutitla,erutar

eldnaHevlaVfopoToT"63