Page 1
5 TON ELECTRIC
LOG SPLITTER
MODEL NO. 40100500
Owner’s Manual
ASSEMBL Y & OPERA TING INSTRUCTIONS
This safety alert symbol identifies important safety messages in this manual.
Failure to follow this important safety information may result in serious injury or
death.
LS102-778-0608
Rev. 0
Page 2
Table of Contents
Page(s)
Important Safety Information................................................................................................................. 1-6
Intended Use ......................................................................................................................... 1
Personal Protective Equipment ............................................................................................... 1
General Safety ...................................................................................................................... 3
Safety Decals ....................................................................................................................... 2
Preparation of the Log ........................................................................................................... 3
Work Area ........................................................................................................................... 3
Operation of the Log Splitter ..................................................................................................3
Repair and Maintenance Safety ............................................................................................. 4
Hydraulic Safety .................................................................................................................. 4
Fire Prevention ..................................................................................................................... 5
Transportation ...................................................................................................................... 5
Assembly Instructions ...................................................................................................................... 6
Operating Instructions ....................................................................................................................... 6-8
Directions for Filling Hydraulic System .................................................................................... 7
Storage ................................................................................................................................ 7
Operation .............................................................................................................................. 7-8
Maintenance ...................................................................................................................................... 8
Parts List ........................................................................................................................................ 9
Parts Breakdown Illustration ............................................................................................................... 10
Notes ................................................................................................................................................ 12
Specifications .................................................................................................................................. Back Cover
Page 3
WARNING: Read and thoroughly understand all instructions and safety information before assembling
or operating this log splitter. Failure to do so may cause serious injury or death. Do not allow anyone
to operate this log splitter who has not read this manual. As with all power equipment, a log splitter
can be dangerous if assembled or used improperly. Do not operate this log splitter if you have doubts
or questions concerning safe operation. Call our customer service department at 1-800-525-8322 to
address these concerns.
Si no entiende ingles, se prefiere que busque alguien que interprete las instrucciones para usted.
INTENDED USE
NEVER use this log splitter for any other purposes than splitting wood. It is designed for this use only. Any other use can
cause serious injury or death.
PEPER
PERSONAL PROTECTIVE EQUIPMENT
PERPERSONALSONAL PROTECTIVE EQUIPMENT
BEFORE operating this log splitter make sure that you wear safety gear such as goggles or safey glasses, steel toed shoes
and tight fitting gloves (without loose cuffs or draw strings). Always wear a protective hearing device when operating this log
splitter.
NEVER wear loose clothing or jewelry that can be caught by moving parts of the log splitter . Keep clothing and hair away
from all moving parts when operating this log splitter .
GENERAL SAFETY
Failure to follow these instructions may result in serious injury or death.
NEVER allow children to operate this log splitter. NEVER allow adult s lacking proper instructions and understanding to
operate this log splitter.
KEEP all people and pets a minimum of 10 feet away from your work area when operating this log splitter . Only the operator
is to be near the log splitter during use.
If a helper is assisting in loading logs, NEVER actuate the control until the helper is clear of the work area.
NEVER operate the log splitter when under the influence of alcohol, drugs or medication.
DL-52-8
NEVER allow a person who is tired or otherwise not alert to use your log splitter.
DL52-2-8
ALWAYS unplug your log splitter when finished. Do not pull on power supply cable to unplug your log splitter.
Page 1
Page 4
SAFETY DECALS
Make sure that all safety warning decals are in good condition and readable. Always replace missing or defaced decals.
Write us or call 1-800-525-8322 and they will be sent to you at no charge.
LOCA TION: SIDE OF BEAM, WEDGE END
P ART NUMBER: 52036900
Read and understand manual
before assembly and operation.
Always wear protective gloves.
Always wear protective shoes.
Always wear protective eye wear.
Caution: Do not touch rotating
parts.
Keep all people and pets away from
work area. Only the operator
should be near the log splitter
during operation.
Caution: Pinch Point
Warning: Moving parts. Never
place body between log and ram
during forward or reverse stroke.
Serious injury or death could result.
Never remove stuck log with bare
hands.
Always disconnect power supply
before performing maintenance,
cleaning, adjustments or moving
the log splitter.
Page 2
Page 5
PREP ARA TION OF THE LOG
Both ends of the log should be cut as square as possible to help prevent the log from riding out of the splitter during
ER
operation. Do not split logs greater than 20 in. in length.
WORK AREA
NEVER operate the log splitter on slippery , wet, muddy or icy ground.
ONLY operate your log splitter on a level surface. Operating on a slope could cause the log splitter to roll over or logs to fall
off.
NEVER operate your log splitter in a damp or rainy environment to avoid electric shock or short circuit.
ALWAYS block the wheels to prevent movement of the log splitter while in operation.
ONLY operate your log splitter in daylight or under good artificial light.
ALWAYS keep the work area clean. Remove split wood around your log splitter immediately so that you don’t stumble
over it.
OPERATION OF THE LOG SPLITTER
ALWAYS enusre the motor is properly grounded or apply protection device. Only use rubber-jacketed cable of sufficient lead
cross section as an extension cable.
KNOW how to stop the log splitter and disengage the controls before operating it.
NEVER place hands, feet or any body part between the ram and splitting wedge during forward or reverse stroke. Serious
injury or death could result.
NEVER straddle or step over the log splitter during operation.
NEVER reach or bend over the log splitter to pick up a log.
NEVER try to split two logs on top of each other.
NEVER try to cross split a second log.
NEVER allow one person to operate the valve while another is positioning the log.
NEVER attempt to load your log splitter when the ram is in motion.
ALWAYS use your hand to operate the control lever and the switch. NEVER use your foot, a rope or any extension device.
NEVER move the log splitter while the motor is running. Shut off the motor even if you are leaving the log splitter for a short
period of time.
Page 3
Page 6
REP AIR AND MAINTENANCE SAFETY
NEVER operate your log splitter when it is in poor mechanical condition or in need of repair.
ALWAYS unplug the power cable before performing any maintenance and repair .
Periodically check that all nuts, bolts, screws, hydraulic fittings and hose clamps are tightened.
NEVER alter your log splitter in any manner such as adding a rope or extenstion to the control lever or adding to the width or
height of the wedge. Such alterations may cause your log splitter to be unsafe and will void the warranty .
Perform all recommended maintenance procedures before using your log splitter.
Replace all damaged or worn parts immediately .
NEVER tamper with the motor to run it at excessive speeds. The maximum motor speed is preset by the manufacturer and
is within safety limits.
NEVER adjust the hydraulic valve. The system is preset at the factory and is within safety limits.
ALW AYS check the level of hydraulic oil before operation.
ALL replacement parts must meet manufacturer’s specifications.
HYDRAULIC SAFETY
The hydraulic system of your log splitter requires careful inspection along with the mechanical parts. Be sure to
replace frayed, kinked, cracked or otherwise damaged hydraulic hose and components.
NEVER check for leaks of hydraulic fluid with your hand. Fluid escaping from a small hole can be almost invisible.
Escaping fluid under pressure can have sufficient force to penetrate skin causing serious personal injury or even death.
Leaks can be detected by passing a piece of cardboard over the suspected leak and looking for discoloration.
ALWAYS seek professional medical attention immediately if injured by escaping hydraulic fluid. Serious infection or reaction
can develop if proper medical treatment is not administered immediately .
ALWAYS be sure to relieve all pressure by shutting off the engine and moving the valve control handle back and forth
should it become necessary to loosen or remove any hydraulic fitting.
NEVER remove the cap from the hydraulic tank or reservoir while the log splitter is running. Hot oil under pressure
could result in serious injury .
NEVER adjust the hydraulic valve. The pressure relief valve on your log splitter is preset at the factory . Only a qualified
service technician should perform this adjustment.
Page 4
Page 7
FIRE PREVENTION
NEVER operate your log splitter near a flame or spark. Hydraulic oil is flammable and can explode.
ALWAYS take a Class B fire extinguisher with you when operating this log splitter in dry areas as a precautionary
measure against possible flying sparks.
TRANSPORT ATION
NEVER move this log splitter while the motor is running.
NEVER carry any cargo or wood on your log splitter.
NEVER allow anyone to sit or ride on your log splitter .
Be careful when moving your log splitter on rugged and rough terrain. Keep your log splitter upright.
Page 5
Page 8
ASSEMBLY INSTRUCTIONS
NOTE: This log splitter was partially assembled at the factory. Refer to the drawing and parts list should it become necessary to disassemble the
unit for repair or replacement of parts.
NOTE: Ensure the power supply is not connected while assembling the log splitter.
STEP 1: Remove all the components from the crate. Inspect each piece for shipping damage. If any part is damaged, contact your dealer or
delivering carrier.
STEP 2: Connect the control handle bar. Align the control handle bar to its linkage part at the back of the log splitter and twist to tighten.
OPERATING INSTRUCTIONS
STEP 1: Preparation
WARNING: Read and thoroughly understand all instructions and safety information before operating
this log splitter. Failure to do so may cause serious injury or death. Do not allow anyone to operate this
log splitter who has not read this manual. As with all power equipment, a log splitter can be dangerous
if assembled or used improperly. Do not operate this log splitter if you have doubts or questions
concerning safe operation. Call our customer service department at 1-800-525-8322 to address these
concerns.
Si no entiende ingles, se prefiere que busque alguien que interprete las instrucciones para usted.
IMPORTANT: The hydraulic tank is shipped with 10W hydrualic fluid. T o use Dextron automatic transmission fluid, you must drain the system.
Do not mix Dextron and 10W hydrualic fluid.
CAUTION: DO NOT START OR RUN THE ENGINE WITHOUT OIL IN THE HYDRAULIC RESERVOIR AND IN
THE ENGINE.
STEP 2: The hydraulic reservoir should be filled with 10W hydraulic oil. If hydraulic oil is difficult to obtain, Dextron automatic transmission fluid can be
substituted. Use only clean oil and take care to prevent dirt from entering the hydraulic reservoir. Do not mix 10W hydrualic fluid with Dextron
transmission fluid. Log splitter is shipped with 10W hydraulic oil, drain system if you wish to use Dextron transmission fluid.
Page 6
Page 9
DIRECTIONS FOR FILLING HYDRAULIC SYSTEM
1) Disconnect the control hand bar from its linkage part and take off the
cushions from the front frame.
2) Lift the towing handle and keep the tank in the vertical position.
3) Disconnect the vent plug and dipstick from the front cylinder cover.
4) Put the front frame of the unit in some container; raise the wheels 2 in.
off the ground on blocks, and drain the hydraulic tank.
5) Refill the tank within the marked range on the dipstick.
6) After refilling, insert and tighten the vent plug and dipstick.
Fill the hydraulic reservoir with at least 3 quarts of hydraulic fluid. After the hydraulic reservoir is filled with oil, start the motor . The hydraulic pump should
prime itself. With the motor running, move the hydraulic valve lever toward the wedge. This will cause the cylinder to extend and expel air. When the
cylinder is fully extended, retract it. Repeat this procedure several times. An erratic movement of the cylinder indicates that there is still air in the system.
More oil should then be added to bring the fluid level up to the “OK” range on the dipstick. T otal hydraulic capacity is 3.3 quarts. NOTE: If the tank is
overfilled, it will tend to expel oil from the breather cap when the cylinder is retracted. After adding more oil to the tank, cycle the cylinder again until it has a
constant speed indicating that all oil has been expelled. Check the oil level in the reservoir again to make sure it is in the “OK” range.
STORAGE
Store the log splitter switched off and unplugged.
Allow the log splitter to cool for 5 minutes after use before storing.
Protect the power supply cable from heat, sunshine, agressive liquids and sharp edges.
Store unit in a clean, dry area. Don’t store it unprotected outdoors, next to corrosive materials or in damp environment.
Store this log splitter where children can not start it.
OPERA TION
WARNING: ALWAYS WEAR SAFETY GLASSES, SAFETY GLOVES, SAFETY SHOES AND SUITABLE WORK CLOTHING WHEN
OPERA TING THIS LOG SPLITTER. NEVER WEAR JEWELRY, NECKTIES OR OTHER LOOSE CLOTHING.
DANGER: KEEP HANDS AND FEET CLEAR OF RAM AND WEDGE AT ALL TIMES.
Page 7
Page 10
1) Place the log splitter on a sturdy , level surface.
2) Ensure the equipment is in safe working condition. Check all nuts, bolts and hydraulic fittings are tight. Check the switch, power cable and plug
are not damaged. Check that all safety shields are in proper position.
3) Check that the outlet’s main voltage and frequency match the data stated on the model plate (or “T echnical Specifications” in this manual).
4) Plug in the power cable and switch on the motor. NEVER use an extension cord longer than 25 feet. Cord gage must be 14 or lower.
5) Place a log on the beam against the wedge. Make sure that the log is securely on the wedge and up against the beam. Logs should be cut wth
square ends and to a maximum length of 20 in. in advance. Always use extra care when splitting logs with unsquare ends.
6) Depress the control handle so that the cylinder will drive the ram into the log. Extend the cylinder until the log splits or to the end of its stroke. If the
log has not completely split after the cylinder has reached the end of its extension, retract the cylinder.
IMPORTANT: Leaving the valve in the “actuate” position at the end of the stroke may damage the pump.
CAUTION: ALWAYS SPLIT THE LOG ALONG ITS GRAIN. IF SPLIT ACROSS THE GRAIN SOME TYPES OF WOOD MAY
BURST OR FLY OUT RESULTING IN INJURY.
CAUTION: IF THE LOG IS STUCK ON THE WEDGE, RELEASE BOTH HANDS AND UNPLUG THE POWER CABLE
IMMEDIATELY. KNOCK OFF THE LOG WITH A HAMMER. DO NOT USE YOUR HANDS.
7) When finished splitting log, switch the motor off and unplug the power cable.
NOTE: If you experience problems splitting especially hard wood, do not keep pushing on the control handle. Release the handle and the ram will
return. If you continue to push the control handle, the ram may fail to retract. If this occurs, turn off the power switch. Then, turn on the power
switch and continue operation.
MAINTENANCE
1) Switch off and unplug power cable before performing any maintenance and repair.
2) Always check the oil level of the hydraulic reservoir before operation. Operating the log splitter without an adequate oil supply will
cause severe damage to the pump.
3) If the wedge becomes dull or nicked, it can be sharpened. AL W A YS wear safety gloves while handling the wedge.
4) See also Repair and Maintenance Safety in the Safety Information section of this manual.
5) All replacement parts must meet manufacturer’s specifications.
NOTE: If the motor is overloaded for a long time, the thermal protector will disconnect the power of the motor. Contact our customer service department.
NOTE: Switch off and unplug the power cable quickly if the machine is acting abnormal. Contact our customer service department to address these
concerns.
Page 8
Page 11
PARTS BREAKDOWN FOR 40100500 LOG SPLITTER
ECNEREFER
REBMUNNOITPIRCSED
1egdewhtiwknaT44-93ylbmessahctiwsyeK
2maR94-54ylbmessaroti
3marfoetalpesaB05revocrebbuR
4rehsawgnirpS25-15ylbmessarevocxobgnitcennoC
5tlobdaehpanS45-35ylbmessadraobgn
6renilnolyN75-55ylbmessarenetsafelbaC
7retlifliO85gulpdnaelbacrewoP
8ebutliO56-95ylbmessaetalpdneraerrotoM
9gn
01tlobderoB76gnirkcehC
11rednilycciluardyH86gnirlaesnotelekS
41-21stundnatfahsnotsiP27-9
51gnirpsgnitcarteR37gnisuohraeG
91-61sgnirlaesdnanotsiP57-47noitcesraeG
12-02gnirlaesdnak
22gnirlaesliO77sebutralunnadnuopmoC
32gnirkcehC18-87ylbmessarevoctnorfpmuP
42revocrednil
52gulptneV29-98ylbmessaeldnahlortnoC
72-62tlobgnoldne-259-39ylbmessaemarferiT
82rotomr
03-92gnirkcehcdnanaF79pilcgnirpS
43-13ylbmessarevocrotomtnorF001-89ylbmessaeldarcgoL
53gniraeB401
63rotatoR501noihsucemarftnorF
73gnisacrotoM901-601ylbmessaeldnahgniwoT
83mottobxobgnitcen
irlaeS66noihsucemarfrotoM
6ylbmessarevocraerpmuP
citspiD67gnirlaesepahs-O
yctnorF88-28evlavciluardyH
ofrevocnaF69eriT
noC211-011ylbmessasdleihS
ECNEREFER
REBMUNNOITPIRCSED
iriW
-101ylbmessaemarftnorF
capaC
NOTE: Drawing and parts list are shown for reference only should it become necessary to disassemble the unit for repair or replacement of parts.
TRAP
REBMUNNOITPIRCSED
00736093tiKlaeSevlaVevlavmorfkaelliO
00836093tiKlaeSknaTciluardyH knatdn
00936093tiKlaeSebuTliOebutliofonoitisopnoitcennocmorfkaelliO
00046093tiKlaeSkcitspiDkcitspidtalaestuo
00146093ylbmessAleehWleehwdegamadronekorB
00246093reniLnolyNmarehtrednurenilnolyntuonroW
DETALER
MELBORP
arevocrednilyctnorffonoitisopnoitcennocmorfkaelliO)A
liO)B
nroW
.natdnaevlavcilaurdyhfonoitisopnoitcennocmorfkael
Page 9
Page 12
PARTS BREAKDOWN FOR 40100500 LOG SPLITTER
Page 10
Page 13
NOTES
Model No. ____________________ Serial No. _____________________________
Date of Purchase _______________ Place of Purchase _______________________
_______________________
_______________________
_______________________
Page 11
Page 14
SPECIFICATIONS
ECROFGNITTILPSMUMIXAM snoT5
TNEMERIUQERLACIRTCELE zH06/V011
TUPNIREWOP W0691
TUPTUOREWOP W0051
TNERRUCDETAR A2
DEEPSROTOM MPR0043
ELBACREWOP mm0.1G3
YTICAPACCILUARDYH strauQ3.3
EMITELCYC sdnoces41
HTGNELGOLMUMIXAM "02
RETEMAIDGOLMUMIXAM "9
ERUSSERPCILUARDYH a
EKORTSREDNILYCMUMIXAM "2/1-02
EZISERIT "7
)HXWXL(SNOISNEMIDENIHCAM "81x"11x"4/1-83
THGIEW .sbl501
1
2
PM02
Loading...