www.specotech.com
Installation an d
Operation Manual
HTFD4T
USER INFORMATION:
Explanation of two Symbols
The lightning flash with arrowhead symbol, within a n equilateral
triangle, is intended to alert the user to the presence of uninsulated
"dangerous voltage" within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to
alert the user to the presence of important operating and maintenance(servicing) instructions in the literature accompanying the appliance.
Read all of the safety and operating instructions before using the product.
Read Instructions
Save this manual fo r later use.
Retain Instructions
Unplug this appliance from wall outlet before cleaning. Do not use liquid
cleaners or aerosol cleaners. Use a damp cloth fo r cleaning.
Cleaning
Do not place this product on an unstable cart, stand, or table .
Use only with a cart or a stand recommended by y our supplier / reseller.
Mounting should follow the manufacturer's instructions, and should use a
mounting accessory recommended by manufacturer.
Do not install the camera in extreme temperature conditions. Only use the
camera where temperatures are within the limits shown in the specifications
section of the user guide. Be especially careful to provide ventilation when
operating under high temperatures.
Installation
This product should be operated only from the type of power source indicated
on the marking label. If you are not su re of the type of power supplied to
your home, consult your dealer or local power company.
Power source
IMPORTANT SAFETY INSTRUC TIONS:
FEATURES:
CAUTION!
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). N O USER SERVICEABLE PART S INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CA UTIO N
RISK OF ELECTRIC SHOCK
DO NOT OPEN
• 1/3 inch Progressive CMOS Image Sensor
• HD-TVI 1080p @ 30fps
• Adjustable motion detec tion (4 areas)
• Adjustable privacy mask (10 masks)
• Flexible Intensier® Technology (INTENSIFIER + Super IR)
• INTENSIFIER (X32)
• Digital Zoom (X12)
• SPECO DNR [ Digital Noise Reduction ]
• WDR [ Wide Dynamic Range ]
• BLC [ Backlight Compensation ]
• MIRROR
• DEFOG
• IP66 Weatherproof housing
SPECIFICATIONS:
DIMENSIONS:
mm (inch
)
Model
Image Sensor
Scanning System
Effective Pixels
Lens
Min Illumination
Backlight
Exposure
White Balance
Day & Night
Functions
Shutter
HD TVI Output
Resolution
Analog Video [ CVBS ]
Coaxial Communication
Supply Voltage
Power Consumption
Operating Temperatu re
Storage Temperature/ Humidity
HTFD4T
1/3 inch CMOS Image Sensor
Progressive Image Processing
1944 (H) x 1092 (V)
2.8-12mm Motorized Focus & Zoom Len s
INTENSIFIER (Max.) : 0 .0005 Lux
IR LED ON : 0.0 Lux
OFF, WDR, BLC, HLC (ON / OFF)
AUTO / MANUAL
ATW INDOOR (2,500°K~7,500°K) /
ATW OUTDOOR (2,000°K~10,000°K) / MANUAL / PUSH
Mechanical ICR Type
WDR, FLICKERLESS, SPECO DNR , ACE, DEFOG,
PRIVACY MASK, MIRROR, BLC
ESC : AUTO
TVI output 1.0 Vp-p, 75 ohm
1920 x 1080p / 30fps or 25fps
Analog Composite (1V ±0.2
Vp-p)
Supports PELCO-C
24V AC (±20%) / 12V DC (±10%)
AC 600mA / DC 700mA, 8.4W (Max.)
-
14°F to 122°F (Heater on: -22° F to 122°F)
-
4°F to 140°F / 20% ~ 90% RH
REGULATORY NOTICE:
This equipment has been tested and found to comply w ith limits for a
Class A digital dev ice, pursuant to part 15 of the FCC Rules.
These limits are designed to provide re asonable protect ion against
harmful interference when the equipment is operated in a commercial
environment.
This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications. Operation of
this equipment in a residential area is likely to cause harmful interference
in which case th e user will be required to correc t the interference at
their own expense .
Changes or modifications not expressly approved by the
manufacturer could void the user's authority to operate the equipment.
WARNING
When this camera is installed near equipment, like a wireless
communication device that emits a str ong elect romagnetic field,
some irregularity such a s noise on the monitor screen may happen.
CAUTION
R50 (1.96
)
92
(
3.62
)
43
(
1.69
)
Ø130 (5.11
)
You must be fully aware of all the distinctive
features and precautions related to this
camera before installing it.
(
438B
)
FLEXIBLEINTENSIFIER
®
TECHNOLOGY
1080p HD-TVI Indoor/Outdoor
Dome Camera with Motorized Lens
1
1
2
2
Stick the guide pattern on the wa ll or ceiling.
Drill three holes according to the guide pattern.
Draw out power/ video wires to the connecting
places.
Attach the camera base to the ceiling or wall
using the supplied th ree screws.
Adjust desired focus and scene by turning and
moving the 3 -Axis camera bracket by hand.
Put the dome cover over the base.
Lock the cover by tightening the screw using
the supplied L-wrench.
– To mount the camera:
CAMERA MOUNTING:
– The camera unit consists of the following parts:
COMPOSITION:
Installation s hould only
be perf ormed by qualified servi ce
personnel in accordance with t he
National Electrical Code or applicable
local codes.
CAUTION
1
2
3
4
5
No.
Guide pattern
Dome base
Mounting screws
Dome cover
L-wrench for dome cover mounting
Part s
3
3
4
4
5
5
OSD MENU:
CAMERA CONTROLS:
SPECO TECH
PRESET INDOOR, OUTDOOR, LOW LIGHT, HALLWAY, LOBBY(WDR), ELEVATOR
EXIT ., RESET
MAIN SE TUP
PUSH
ATW OUTDOOR
MANUAL
ATW INDOOR
WHITE BAL
HLC
WDR
BLC
OFF
BACKLIGHT
Design and specifications are subject to change without notice.
Design and specifications are subject to c hange without notice.
6
No.
Service monitor
connector
Part s
When installing the camera, connect a service monitor to
set angle of view and focus of the screen.
Remark s
1
2
3
4
5
No.
Up (TELE)
Down (WIDE)
Left (NEAR)
Right (FAR)
Menu (Center)
Part s
Move the cursor up in the screen.
Move the cursor down in the screen.
Move the cursor left i n the screen.
Move the cursor right in the screen.
Press straight down to open menu o r set.
• When pressing for 1 sec : AUTO FUCUS
•
When pressing for few sec : Enter into CAMERA MENU
Remark s
Menu navigation
Monitoring and switches
– It will automatically adjust the focus of video after switching Day/Night mode
– When powered on, focus will adjust automatically
Focus Operational Cases
– When there is a speedy movement, appearance and disappearance of objects
– When there is a noticeable change of illumination during the focus adjustment
– When the illumination is too low to recognize the objects
– When it is exposed to direct s unlight
– If a strong impact is appl ied to camera body
There will be malfunction of focus adjustment for the cases below.
D/N FOCUS
MODE
FOCUS
NIGHT
DAY
SPECO DNR
OFF
ON
AUTO
FUSION IR
PRIVACY
SHADING
ACE
DEFOG
COLOR GAIN
GAMMA
MIRROR
D-ZOOM
SHARPNESS
IMAGE
ESC
LENS
LANGUAGE
BAUDRATE
VERSION
SYSTEM
ID DISPLAY
CAM TITLE
CAM ID
GENERAL
DOWN
RIGHT
LEFT
UP
6
6
5
5
DOWN
RIGHT
LEFT
UP
4
4
3
3
1
1
2
2
CONNECTION:
• Conne ct the video-out j ack to the video-in jack of monit or.
• Conne ct the power ad apter to the power i nput connector.
• Th e wire is non-polarized.
• U se 24V AC power source or 12V DC power source.
Video Output
GND
For 24V AC / 12V DC Power Type
1
2
3
No.
Video Output
Video Output
Power Input
Function
White
Yellow
Red
Terminal Color
HD-TVI
CVBS (Analog 960H)
24V AC (±20%) / 12V DC (±10%)
Remark s
12V DC
24V AC
AC AC
1
1
3
3
2
2
• The tape material butyl rubber is ex tended more than double
size. Winding t ightly cable connec tion to preve nt leaking
on cable.
• This product is IP66 waterproof certified one but the external
cable connec tion part i s not waterproof. Do not expose
cable on dro pping water or humid pla ce and be sure to
wring waterproof rubber tape.
PRECAUTION - Outdoor Installation
–
Leaking expected at connected cable on outdoor i nstallation. Use the
waterproof rubber tape winding up on cable connection as following picture.
1
1
2
2
3
3
Pan
36 0°
90°
Tilt
350°
Horizontal
• Connect cables.
AAA
A
•
Winding rubber tape with half overlay on external
cable jacket (A) and cable connection.
• Winding each cable with using rubber tape.
HD-TVI
Analog
Power
Loading...