Spalding M890001 User Manual

1

09/06 ID# M890001

IMPORTANT!

To ensure prompt and correct handling of any problems, or to answer any questions, please

contact the Sample and Display Technician at 1-800-558-5234.

Display System

Owners Manual

Customer Service Center

• N53 W24700 South Corporate Circle • Sussex, WI 53089 • U.S.A.

Model

89226

7/16"

REQUIRED TOOLS AND MATERIALS:

• 2 Capable Adults

• 2 Stepladders

• Phillips Screwdriver

• (2 each) Wrenches and/or
Socket Wrenches and
Sockets.

1/2" 9/16"

7/16" 1/2" 9/16"

AND/OR

READ AND UNDERSTAND
OPERATOR'S MANUAL
BEFORE USING THIS UNIT.

FAILURE TO FOLLOW
OPERATING INSTRUCTIONS
COULD RESULT IN INJURY
OR DAMAGE TO PROPERTY.

WARNING!

© COPYRIGHT 2006 by SPALDING

ID# M890001 09/06

2

IMPORTANT!

Remove all contents from boxes.

Be sure to check inside pole sections;

hardware and additional parts are packed inside.

NOTICE TO ASSEMBLERS

ALL basketball systems, including those used for DISPLAYS, MUST be assembled and ballasted with sand

or water according to instructions. Failure to follow instructions could result in SERIOUS INJURY. It is

NOT acceptable to devise a makeshift weight system.

SAFETY INSTRUCTIONS

FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY

RESULT IN SERIOUS INJURY,

PROPERTY DAMAGE AND WILL VOID WARRANTY.

This unit is intended for display purposes only and

should not be used for play.

To ensure safety, do not attempt to assemble this system without
following the instructions carefully. Check entire box and inside all
packing material for parts. Before beginning assembly, read the
instructions and identify parts in this document. Proper and
complete assembly, use and supervision is essential for proper
operation and to reduce the risk of accident or injury. A high
probability of serious injury exists if this system is not installed,
maintained, and operated properly.

• During assembly, if using a ladder use extreme caution. Two
capable adults are recommended for this operation.

• If technical assistance is required, contact the Sample and Display
Technician.

• Serious injury could occur if teeth/face come in contact with
backboard, net or rim.

• Display recommended for 3” (7.6 cm) or 3-1/2” (9 cm) Round
or 4” (10 cm) Square poles only.

• All instructions and warnings MUST accompany any display item
that is sold.

Most injuries are caused by misuse and/or not following

instructions. Use caution when installing this unit.

3

09/06 ID# M890001

PARTS LIST (See Hardware Identifier)

Item #17 (2)

HARDWARE IDENTIFIER (Nuts, Washers & Springs)

Item #9 (12)

Item #11 (12)

Item Qty. Part No. Description

1 2 200318 Bracket, Reinforcement S/J
2 1 200503 P/S Cover
3 2 200520 Screw, #8 x 3/4", Flat Head, Phillips
4 2 200533 Spacer, Mounting
5 3 990062 Pole, 3.5"
6 3 201344 Plastic Knob
7 12 201611 Bolt,Hex-Flange, 5/16-18 x 3"
8 1 202795 NBA Sticker

9 12 203063 Lock Nut, 3/8-16 Nylon Insert
10 1 203157 Bolt, Carriage, 5/16-18 x 2.25"
11 12 203100 Nut, Hex-Flange 5/16-18 Whiz Lock
12 2 203231 Bolt, Carriage, 5/16-18 x 3.5"
13 6 203294 Bolt, U, Round, 3/8-16 x 3.5"
14 4 203309 Washer
15 2 203470 Washer, Flat, S/J
16 2 203472 Spring

Item Qty. Part No. Description

17 2 203795 Nut, 3/8-16 Special S/J
18 2 203796 T-bolt, 3/8-16 x 5"
19 1 203798 Bolt, Hex 5/16-18 x 1.5"
20 4 204290 Net
21 1 206219 Pole Cap, 3"
22 3 207103 Pole Cap, 3.5"
23 2 900033 Bracket, S/J
24 1 900060 Pole, 3"
25 4 Rim
26 1 900253 Bracket, Pole Mount, No Tools
27 1 206987 Wedge
28 1 909256FR Board, 48", Fan, Viper
29 1 90925901 Board, 44", Fan, Evolution, NT
30 1 909602FR Board, 44", Fan, Zone Attack
31 3 912006 Extension Arm
32 1 979235FR Board, 48", SFA, Titanium II
33 1 902319 Bracket, Reinforcement, No Tools

Item #7 (12)

Item #18 (2)

Item #3 (2)

Item #16 (2)

Item #15 (2)

Item #14 (4)

Item #19 (1)

Item #10 (1)

Item #12 (2)

HARDWARE IDENTIFIER (Bolts and Screws)

ID# M890001 09/06

4

Install display boards in the marked locations. Each mounting location consists of a mounting pole stub with
the following dimensions: Height = 8”, O.D. = 3 3/8”, I.D. = 3 1/8” (arrows indicate direction the board is
facing).

Display boards will be mounted as follows:

Corner Location 1: 9H235A

• 48” SFABoard

• Titanium II Logo

• Black Slam Jam Goal with Cover

• Use extension arm for assembly

Corner Location 2: 73256

• 48” Fan Recycled Board

• Viper Logo

• Black Slam Jam Goal

• Use extension arm for assembly

Corner Location 3: 61259

• 44” Fan Recycled Board

• Evolution Logo

• Black Standard Goal

• No Tools, E3 Elevator System

Corner Location 4: 80602

• 44” Fan Recycled Board

• Zone Attack Logo

• Black Standard Goal

• Use extension arm for assembly

Corner “2”

73256

Corner “4”
80602

Corner “3”

61259

Corner “1”
9H235A

Display Stand - Top View

3-1/2"

3"

3-1/2"

3-1/2"

5

09/06 ID# M890001

1.

Slide the 3" diameter end of the display pole (24)
inside the pole sleeve.

Secure the display pole by sliding the display
wedge (27) into position as shown. To lock the
display pole in place, tighten the hex-bolt (19).

24

24

27

19

At corner location 1, 2 and 4 slide
the 3-1/2" diameter end of the
display pole (5) out

side the mounting

stubs.

2.

5

ID# M890001 09/06

6

1.

2.

Corner Location 1: STEEL FRAME ACRYLIC BACKBOARD ASSEMBLY

32

7

23

Insert “T” bolt (18) through Slam Jam bracket (23) as shown.
Secure Slam Jam bracket (23), extension arm (31) and
mounting spacers (4) assemblies to backboard using bolt (7 )
and nut (11) as shown.

Corner “2”

73256

Corner “4”
80602

Corner “3”

61259

Corner “1”
9H235A

Display Stand - Top View

3-1/2"

3"

3-1/2"

3-1/2"

11

18

32

9

13

Attach board assembly to pole.

4

4

31

22

TWO CAPABLE ADULTS
REQUIRED FOR THIS
PROCEDURE. FAILURE TO
FOLLOW THIS WARNING COULD
RESULT IN SERIOUS INJURY
AND/OR PROPERTY DAMAGE.

WARNING!

11

9

9

7

09/06 ID# M890001

1

17

15

16

25

23

18

• Fit rim (25) securely into bracket (23) as shown.

• Install reinforcement bracket (1) onto “T” bolt (18) as shown.

• Install spring (16) onto “T” bolt (18) as shown.

• Install special nut (17) and washer (15) onto “T” bolt (18).

3

.

3

25

2

8

2

Apply logo label (8) to rim cover (2).

4.

5.

Attach cover (2) to rim using
screws (3).

Peel protective

film from surface

of acrylic

backboard prior to

use.

NOTE:

Tighten nut (17) until flush
with end of "T" bolt (18) as

shown here.

NOTE:

ID# M890001 09/06

8

Corner Location 2: 48” FAN MOLDED PLASTIC BOARD ASSEMBLY

1.

Insert “T” bolt (18) through Slam Jam bracket
(23) as shown.
Secure Slam Jam bracket (23) and extension
arm (31) to backboard using bolt (7) and nut
(11) as shown.

Tighten completely.

28

23

11

7

18

31

18

28

9

9

9

13

2.

Attach board assembly to pole.

Corner “2”

73256

Corner “4”
80602

Corner “3”

61259

Corner “1”
9H235A

Display Stand - Top View

3-1/2"

3"

3-1/2"

3-1/2"

22

TWO CAPABLE ADULTS
REQUIRED FOR THIS
PROCEDURE. FAILURE TO
FOLLOW THIS WARNING COULD
RESULT IN SERIOUS INJURY
AND/OR PROPERTY DAMAGE.

WARNING!

7

9

09/06 ID# M890001

3.

• Fit rim (25) securely into bracket (23) as shown.

• Install reinforcement bracket (1) onto “T” bolt (18) as shown.

• Install spring (16) onto “T” bolt (18) as shown.

• Install special nut (17) and washer (15) onto “T” bolt (18).

1

17

15

16

25

23

18

Tighten nut (17) until

flush with end of

"T" bolt (18) as

shown here.

NOTE:

ID# M890001 09/06

10

Corner Location 3: 44" FAN MOLDED PLASTIC BOARD ASSEMBLY

Pole bracket will need to be lightly pressed into
backboard ribbing. Be sure to press completely into
place. Attach rim (25) to backboard and pole bracket
(26) with knob (6), reinforcement bracket (1), and
carriage bolt (10) as shown. Tighten knob
completely.

10

6

33

26

25

Attach board assembly to pole with carriage
bolts (12) and knobs (6) as shown. Install pole
cap (21) as shown.

6

12

21

1.

2.

24

29

Corner “2”

73256

Corner “4”
80602

Corner “3”

61259

Corner “1”
9H235A

Display Stand - Top View

3-1/2"

3"

3-1/2"

3-1/2"

BOARD STYLE

MAY VARY.

NOTE:

KNOB MUST BE TIGHTENED
COMPLETELY AND CHECKED
FOR TIGHTNESS BEFORE
EACH USE.

WARNING!

PRESS BRACKET (26)

INTO PLACE HERE

6

11

09/06 ID# M890001

Corner Location 4: 44" FAN MOLDED PLASTIC BOARD ASSEMBLY

1.

Attach rim (25) to backboard (30) and
extension arm (31) with bolts (7), washers (14)
and nuts (11).

Tighten completely.

30

11

7

31

25

30

9

13

2

.

Attach board assembly to pole.

Corner “2”

73256

Corner “4”
80602

Corner “3”

61259

Corner “1”
9H235A

Display Stand - Top View

3-1/2"

3"

3-1/2"

3-1/2"

22

14

14

TWO CAPABLE ADULTS
REQUIRED FOR THIS
PROCEDURE. FAILURE TO
FOLLOW THIS WARNING COULD
RESULT IN SERIOUS INJURY
AND/OR PROPERTY DAMAGE.

WARNING!

11

9