Spalding M88604C1 User Manual

1
08/06 ID# M88604C1
Toll-Free Customer Service Number for U.S: 1-800-334-9111
Spalding Internet Address: http://www.spalding.com
Write Model Number
From Box Here:
WARNING!
READ AND UNDERSTAND OPERATOR'S MANUAL BEFORE USING THIS UNIT.
FAILURE TO FOLLOW OPERATING INSTRUCTIONS COULD RESULT IN INJURY OR DAMAGE TO PROPERTY.
This manual, accompanied by sales receipt, should be saved and kept on hand as a convenient reference, as it contains
important information about your model.
Adult Assembly Required.
High End Residential
In-Ground Basketball System
Owners Manual
Customer Service Center
• N53 W24700 South Corporate Circle • Sussex, WI 53089 • U.S.A.
2
ID# M88604C1 08/06
Owner must ensure that all players know and follow these rules
for safe operation of the system.
WARNING
DO NOT HANG on the rim or any part of the system including backboard, support braces or net.
During play, especially when performing dunk type activities, keep player's face away from the backboard, rim and net. Serious injury could occur if teeth/face come in contact with backboard, rim or net.
Do not slide, climb, shake or play on base and/or pole.
When adjusting height or moving system, keep hands and fingers away from moving parts.
Do not allow children to move or adjust system.
During play, do not wear jewelry (rings, watches, necklaces, etc.). Objects may entangle in net.
Keep organic material away from pole base. Grass, litter, etc. could cause corrosion and/or deterioration.
Check pole system for signs of corrosion (rust, pitting, chipping) and repaint with exterior enamel paint. If rust has penetrated through the steel anywhere, replace pole immediately.
Check system before each use for proper ballast, loose hardware, excessive wear and signs corrosion and repair before use.
Check system before each use for instability.
Never play on damaged equipment.
Keep pole top covered with cap at all times.
See instruction manual for proper installation and maintenance.
Read and understand warnings listed below before using this product.
Failure to follow these warnings may result in serious injury and/or property damage.
ID#: 588000 01/05
In the U.S.: 1-800-xxx-xxxx
Canada: 1-800-xxx-xxxx
In the U.S.: 1-800-xxx-xxxx
Canada: 1-800-xxx-xxxx
In the U.S.: 1-800-xxx-xxxx
Canada: 1-800-xxx-xxxx
In the U.S.: 1-800-xxx-xxxx
Canada: 1-800-xxx-xxxx
Most injuries are caused by misuse and/or not following instructions.
Use caution when using this system.
• If using a ladder during assembly, use extreme caution.
• Three (3) capable adults are recommended for this operation.
• Before digging, contact utility company to locate underground power cables, gas, and water lines. Ensure there are no overhead power lines within 20 ft. (7 m) radius of pole location.
• Climate, corrosion, excessive use, or misuse could result in system failure.
• If technical assistance is required, contact Customer Service.
• Minimum operational height is 6'6" (1.98 m) to the bottom of backboard.
• This equipment is intended for home recreational use only and NOT excessive competitive play.
• Read and understand the warning label affixed to pole.
• The life of your basketball pole depends on many conditions. The climate, placement of the pole, the location of the pole, exposure to corrosives such as pesticides, herbicides or salts are all important.
• Adult supervision is recommended when adjusting height.
• Serious injury could occur if teeth/face come in contact with backboard, net, or rim.
FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN
SERIOUS INJURY, PROPERTY DAMAGE AND WILL VOID WARRANTY.
Owner must ensure that all players know and
follow these rules for safe operation of the system.
To ensure safety, do not attempt to assemble this system without following the instructions carefully. Proper and complete assembly, use and supervision is essential for proper operation and to reduce the risk of accident or injury. A high probability of serious injury exists if this system is not installed, maintained, and operated properly. Check entire box and inside all packing material for parts and/or additional instructional material. Before beginning assembly, read the instructions and identify parts using the hardware identifier and parts list in this document.
For more information on assembly, placement, proper use and maintenance, visit The American Basketball Council website at http://www.smarthoops.com.
REQUIRED TOOLS AND MATERIALS:
• Three Capable Adults
• Carpenter’s Level
• 15’ Tape Measure
• Shovel & Post Hole Digger
• Wood Board (scrap)
• (2) Stepladders 8 ft. (2.4 m)
• Safety Goggles
• Container to Mix
• (2 each) Wrenches and/or Socket Wrenches and Sockets (Deep-Well Sockets are Recommended).
1/2" 15/16"9/16" 3/4"
• Optional: Large & Small Adjustable Wrenches
1/2" 15/16"9/16" 3/4"
• (1) Utility Knife
Phillips-Head Screwdriver
3
08/06 ID# M88604C1
Item Qty.
Part No. Description
1 1 968880 Pole 2 1 908266 Tube, Ground Anchor, Black 3 1 Rim Assembly 4 1 Net 5 4 205702 Nut, Hex, 3/8-16 6 4 203300 Washer, Locking, 3/8 7 4 205700 Bolt, Hex, 3/8-16 x 3.5” Long 8 1 204922 Pin, Hitch
9 1 204923 Pin, Cotter, #8 10 3 204993 Rebar, .5” diameter, 18” Long 11 1 516000 Label, Height Adjustment 12 1 204940 Screw Jack 13 1 Backboard 14 1 80854501 Rod, Threaded Assembly, 5/8-11 x 19.8”, Zinc 15 1 204921 Washer, Barrel 16 1 Cover, Rim 17 1 978881 Yoke, Upper, Center, Pole 18 1 988881 Yoke, Lower, Center, Pole 19 26 204670A Bushing, Plastic 20 1 202900 Bolt, Hex, 1/2-13 x 5, Zinc 21 16 202651 Washer, Flat, 0.053” I.D., 1.08” O.D., Zinc 22 9* 206340 Nut, Lock, Nylon Insert, 1/2-13, Zinc 23 2 220048 Bolt, Hex Head, 1/2”-13 x 6”, Zinc 24 9 200704 Washer, Flat, 0.656” I.D., 1.313” O.D., Zinc 25 8 265575 Nut, Hex, 5/8-11, Zinc 26 1 215008 Nut, Hex, 5/8-11, Grade 8, Black 27 4* 203309 Washer, Flat, 3/8” 28 2* 224728 Bolt, Hex, 1/2-13 x 9.25, Black Zinc 29 4 204733 Screw, #8, .50 Long 30 2 204735 Height Indicator, Plastic 31 1 204741 Label, Height Indicator, Right 32 1 204742 Label, Height Indicator, Left 33 2* 206311 Spacer, .52 I.D. x .75 I.D. x .5” Long, Plastic 34 4 205830 Bolt, Hex, 1/2-13 x 2.5, Zinc
* You May Have Extra Parts With This Model.
PARTS LIST
11
ID# 516000 06/05
4
ID# M88604C1 08/06
Item #5 (4)
HARDWARE IDENTIFIER (BOLTS & SCREWS)
Item #34 (4)
Item #24 (9)
Item #21 (16)
Item #28 (2)*
Item #26 (1)
Item #25 (4)
Item #22 (9)*
HARDWARE IDENTIFIER (NUTS, WASHERS & SPACERS)
Item #8 (1)
Item #9 (1)
Item #15 (1)
Item #19 (26)
HARDWARE IDENTIFIER (OTHER-NOT ACTUAL SIZE)
Item #27 (4)*
Item #33 (2)*
Item #6 (4)
Item #7 (4)
Item #20 (1)
Item #23 (2)
Item #29 (4)
5
08/06 ID# M88604C1
Ensure ground is level with playing surface, then dig pole hole.
CONTACT UTILITIES BEFORE DIGGING.
WARNING!
24" (61 cm)
48" (121.9 cm)
PLAYING SURFACE
GROUND SURFACE
24" (61 cm)
48" (121.9 cm)
1.
Install nuts (25) onto the ground tube bolts as shown.
Nuts on the top of the plate are used for leveling the pole after system is fully assembled.
NOTE:
2.
2
25
6
ID# M88604C1 08/06
SIDE VIEW
DRAINAGE HILL
PLAYING SURFACE
Fill hole with concrete. Tamp down concrete to release air pockets and build drainage hill.
3.
Insert rebar (10) through holes in ground tube assembly (2) as shown.
4.
10
10
10
2
1" (2.54 cm)
7
08/06 ID# M88604C1
IMPORTANT!:
W AIT A MINIMUM OF 72 HOURS BEFORE GOING ON
TO NEXT STEP. CONCRETE MUST
CURE. ALLOW ADDITIONAL TIME
FOR COLD, WET OR HUMID WEATHER.
IMPORTANT!
Check leveling of mounting plate
several times with carpenter’s level
while concrete is curing.
24
24
24
24
Insert ground tube assembly (2) into cement as shown. Move assembly around to release any air pockets in cement, then rest mounting plate on cement drainage hill. Apply some pressure to level mounting plate on top of drainage hill. Level mounting plate and square with playing surface. Clean off any excess cement on mounting plate at this time and place washers (24) on mounting bolts (19).
5.
PLAYING SURFACE
IMPORTANT!
NOTE ORIENTATION
Front of mounting
plate (2) must be
parallel with playing
surface.
10
10
2
PLAYING SURFACE
10
8
ID# M88604C1 08/06
Insert bushings (19) into areas shown.
6.
19
19
19
1
13
19
19
17
18
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
19
9
08/06 ID# M88604C1
Rest top of pole on a piece of scrap wood (not included) and line up holes in pole (1) to holes in mounting plate (2) as shown.
7A.
22
23
1
PLAYING SURFACE
2
Insert bolt (23) through holes in plate and pole and secure with nut (22).
7B.
SCRAP WOOD
(NOT INCLUDED)
THREE CAPABLE ADULTS REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE.
WARNING!
1
1
PLAYING SURFACE
10
ID# M88604C1 08/06
8.
26
24
15
9
8
14
Completed Assembly
TWO people are required to lift pole into
position so that the threaded assembly rod (14) can be installed and secured by the THIRD person.
While pole is being supported by TWO capable adults, position rod (14) and lock into place with hitch pin (8) and cotter pin (9).
Slide barrel washer (15) onto other end of rod (14) and secure with washer (24) and nut (26). Tighten nut (26) until it is positioned at 3-3/4” from the end of the rod (14) as shown (Figure A)
3-3/4”
FIGURE
A.
1
14
26
1
THREE CAPABLE ADULTS REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE.
WARNING!
11
08/06 ID# M88604C1
While still in forward position, attach both upper and lower yokes (17 & 18) to pole as shown.
9.
22
21
28
21
17
18
THREE CAPABLE ADULTS REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE.
WARNING!
12
ID# M88604C1 08/06
22
12
19
21
20
18
21
19
Attach elevator adjustment (12) to lower yoke (18).
10.
THREE CAPABLE ADULTS REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE.
WARNING!
13
08/06 ID# M88604C1
Attach elevator adjustment (12) to pole bracket.
11.
12
23
21
22
33
33
21
THREE CAPABLE ADULTS REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE.
WARNING!
14
ID# M88604C1 08/06
Attach backboard (13) to upper and lower yokes (18 & 17).
First attach board (13) to upper yoke (17), using TWO people to hold the board and ONE person to attach hardware (FIG. A). Use hardware as shown in FIG. B.
12. A.
FIG. A
FIG. C
Then, hinge board to match up with holes in lower yoke (18), FIG. C, and secure with hardware as shown in FIG. D.
21
22
21
13
FIG. B
22
21
21
34
34
21
22
21
FIG. D
22
21
21
34
34
B.
13
18
17
17
18
THREE CAPABLE ADULTS REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE.
WARNING!
15
08/06 ID# M88604C1
13.
5
7
Refer To Instructions
Included With Rim
Hardware For Rim
Assembly.
3
Rim Assembly
6
13
7
IMPORTANT!
Carefully cut and peel protective film away from board prior to attaching rim.
Before starting rim assembly, tighten nut (26) until it is positioned 6-3/4” from the end of the rod as shown (Figure A).
Remove rim cover (16), attach rim assembly (3) to backboard (13) and reattach rim cover (16).
** For rim assembly, see instructions included with rim.
6-3/4”
FIGURE
A.
27
27
16
26
14
16
ID# M88604C1 08/06
14. A.
15.
Apply height indicator labels (32 & 31) to height indicators (30).
2.
4.
3.
1.
Install net (4) to rim as shown.
Set-up For Right SideSet-up For Left Side
32
31
30
30
B.
Attach height indicators to lower yoke in area shown by turning screws (29) into place with a phillips-head screwdriver.
IMPORTANT!
NOTE ORIENTATION
OF HEIGHT
INDICATORS: 10’ MARK SHOULD FACE AWAY FROM
BACKBOARD.
C.
Attach height indicators to lower yoke in area shown by turning screws (29) into place with a phillips-head screwdriver.
29
29
10
9
78
10
9
78
10
9
8
7
7
8
10
9
7
8
10
9
10
9
8
7
17
08/06 ID# M88604C1
PLAYING
SURFACE
WAR
NING
F
AILURE
T
O
FOLLO
W
THESE
W
ARNINGS
MA
Y
RESUL
T
IN
SERIOUS INJUR
Y
AND/OR
PR
OPER
TY
D
AMA
GE.
Owner
m
ust
ensure
that
all
pla
y
er
s
kno
w
and
f
ollow
these
rules
f
or
saf
e operation
of
the
system.
See
instruction
man
ual
f
or
pr
oper
installation.
DO
NO
T
HANG
on
the
rim
or
an
y par
t
of
the
system
inc
luding
bac
kboar
d,
suppor
t
braces
or
net.
During
pla
y
,
especiall
y when
perf
orming
dunk
type
activities,
keep
pla
y
er's
face
a
wa
y
fr
om
the
bac
kboar
d,
rim
and
net.
Serious
injur
y could
occur
if
teeth/face
come
in
contact
with
bac
kboar
d,
rim
or
net.
Do
not
slide
,
c
limb,shake
or
pla
y
on
pole
.
When
adjusting
height,
keep
hands
and
fing
er
s
a
wa
y
fr
om
mo
ving
par
ts.
Do
not
allo
w
c
hildren
to
mo
ve
or
adjust
system.
During
pla
y
,do
not
wear
je
welr
y
(rings,
watc
hes,
nec
klaces,
etc.);
objects
ma
y
entangle
in
net.
K
eep
or
ganic
material
a
wa
y
fr
om
pole
base
.
Grass,
litter
,
etc.
could
cause corr
osion
and
or
deterioration.
Check pole
system
f
or
signs
of
corr
osion
(rust,
pitting,
c
hipping)
and
repaint
with
with
exterior
enamel
paint.
If
rust
has
penetrated
thr
ough the
steel
an
ywhere
,
replace
the
pole
immediatel
y
.
Check
system
bef
ore
eac
h
use
f
or
pr
oper
ballast,loose
har
d
ware
,
e
xcessive
wear
and
signs
corr
osion
and
repair
bef
ore
using.
Check
system
bef
ore
eac
h
use
f
or
instability
.
Ne
ver
pla
y
on
dama
g
ed
equipment.
K
eep
pole
top
co
vered
with
cap
at all
times.
201255
2/99
1-800-558-5234
1
25 24
16.
1
26
Upright pole (1) by tightening nut (26). Using 15/16” wrench, turn nut (26) clockwise to begin standing pole upright. Continue to turn nut (26) until pole has come to rest against washers (24) and pole is vertical.
Once pole is in its final position, install washers (24) and nuts (25) onto bolts (19) and fully tighten to secure pole to anchor plate.
THREE CAPABLE ADULTS REQUIRED FOR THIS PROCEDURE. TWO PEOPLE ARE REQUIRED TO GUIDE AND SUPPORT THE SYSTEM WHILE THE THIRD PERSON IS TIGHTENING NUT (26) TO RAISE THE SYSTEM UPRIGHT.
FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE.
WARNING!
19
19
24
THREE CAPABLE ADULTS REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE.
WARNING!
18
ID# M88604C1 08/06
17.
After pole has been secured to the anchor plate (2) loosen nut (26), remove cotter pin (9), and pull out pin (8). This will allow the removal of the assembly rod (14) which is no longer necessary for the remainder of the assembly and installation of system.
15
9
8
24
26
14
25
ONLY AFTER THE ANCHOR PLATE HAS BEEN FULLY TIGHTENED: Remove cotter pin (9) and pin (8) to remove threaded assembly rod
(14)
from anchor plate (2).
WARNING!
19
08/06 ID# M88604C1
12
19.
Apply height adjust ment label (11). Adjust system by turning crank until desired height is reached
per height indicator (30).
11
30
10 feet
(3.05 m)
READ AND UNDERSTAND WARNING & HEIGHT ADJUSTMENT LABELS BEFORE USING THIS UNIT.
FAILURE TO FOLLOW OPERATING INSTRUCTIONS COULD RESULT IN INJURY OR DAMAGE TO PROPERTY.
WARNING!
Check system leveling. Pole (1) should be level in all directions. After system is leveled, completely tighten all nuts (25).
18.
If adjustment is necessary, adjust system by rotating the nuts (25) between anchor plate (2) and pole flange.
NOTE:
25
1
2
20
ID# M88604C1 08/06
Subject to proper installation and normal use, Spalding
®
warrants, subject to limitations below, to the original retail
purchaser all structural components of the Spalding
®
system to be free of defects in material and workmanship
for the duration of ownership by the original retail
purchaser.
Merchandise must be shipped prepaid with a copy of proof
of purchase to our factory for examination to see whether
it needs to be repaired or replaced. Any labor costs,
travel expenses and any other charges involved in the
removal, installation or replacement of the
defective/repaired parts from/to your Spalding
®
system
will be your (the purchaser’s) responsibility. Shipping
charges for replaced or warranted merchandise being
sent back to the customer from our factory must be
prepaid by the customer in advance. If not, the
replacement shipment will be sent out collect.
What is Not Covered By This Warranty
Paint or rusted parts. Paint kits will be available to assist in
normal maintenance.
RIM
HANGING ON THE RIM WILL VOID YOUR WARRANTY.
Rims are not warranted for any defects other than
workmanship. Torn back plates, damaged springs, bent
rings, damaged eye bolts, and torn or distorted rim
supports result from hanging on the rim and are not
warranted.
LIMITED LIFETIME WARRANTY
Loading...