SOYO SY-K7ADA User Manual 2

Download

Hardware

Installation

Quick BIOS

Introduction

The SOYO CD

SY-K7ADA

Motherboard

Setup

Quick Start Guide

SOYO™

SY-K7ADA Motherboard

Socket 462 for AMD® Athlon/DuronTM processors ALI MAGiK1 AGP/PCI Motherboard 200/266 MHz Front Side Bus supported ATX Form Factor

Trademarks:

Soyo is the registered trademark of Soyo Computer Inc. All trademarks are the properties of their owners.

Product Rights:

All names of the product and corporate mentioned in this publication are used for identification purposes only. The registered trademarks and copyrights belong to their respective companies.

All rights reserved. This manual has been copyrighted by Soyo Computer Inc. No part of this manual may be reproduced, transmitted, transcribed, translated into any other language, or stored in a retrieval system, in any form or by any means, such as by electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without permission in writing from Soyo Computer Inc.

Disclaimer:

Soyo Computer Inc. makes no representations or warranties regarding the contents of this manual. We reserve the right to amend the manual or revise the specifications of the product described in it from time to time without obligation to notify any person of such revision or amend. The information contained in this manual is provided to our customers for general use. Customers should be aware that the personal computer field is subject to many patents. All of our customers should ensure that their use of our products does not infringe upon any patents. It is the policy of Soyo Computer Inc. to respect the valid patent rights of third parties and not to infringe upon or to cause others to infringe upon such rights.

Restricted Rights Legend:

Use, duplication, or disclosure by the Government is subject to restrictions set forth in subparagraph (c)(1)(ii) of the Rights in Technical Data and Computer Software clause at

252.277-7013.

About This Guide:

This Quick Start Guide can help system manufacturers and end users in setting up and installing the Motherboard. Information in this guide has been carefully checked for reliability; however, to the correctness of the contents there is no guarantee given. The information in this document is subject to amend without notice.

For further information, please visit our Web Site on the Internet. The address is

"http://www.soyo.com.tw".

K7ADA Serial - Version 1.2 - Edition: May 2001

* These specifications are subject to amend without notice

Introduction

SY-K7ADA

Quick Start Guide

Congratulations on your purchase of the illustrates the steps for installing and setting up your new Motherboard.

This guide provide users with the basic steps of Motherboard setting and operation. For further information, please refer to the

Motherboard.

SY-K7ADA

SY-K7ADA User’s Guide

Motherboard. This

Quick Start Guide

that came with your

Unpacking

When unpacking the Motherboard, check for the following items:

The SY-K7ADA ALi MAGiK1 AGP/PCI Motherboard

The Quick Start Guide

The Installation CD-ROM

SOYO Bonus Pack CD-ROM

One IDE Device ATA33/ 66/100 Flat Cable

One Floppy Disk Drive Flat Cable

One Heat Sink Compound

SY-K7ADA Quick Start Guide

Introduction

SDRAM

M1647

AGP Slot

Lithium

JP1

RJ3

CDIN1

PCI Slot #5

PCI Slot #1

PCI Slot #4

PCI Slot #3

FLP

IDE 1

IDE 2

M1535D+

FJ1

ALi

JP5

JP10

Header

SY-K7ADA Motherboard Layout

PS/2 KB

PS/2 Mouse

Connector

USB 1_2

PRT

COMA

COMB

AGAME

AOUT AIN AMIC

ATX Power

VJ1

3 1

VJ2

ALi M5879

Sigmatel STAC9700

ALi M5819

PCI Slot #2

Flash BIOS

RJ2

RJ1

3 1

Battery

WOL

Introduction

Key Features

Supports Socket A (Socket 462) AMD® processors

¡X

Supports 200MHz Front Side Bus

Athlon(750MHz~1.3GHz)

Duron (600MHz~900MHz)

¡X

Supports 266MHz Front Side Bus

Athlon(1GHz~1.33GHz)

PC99, ACPI 1.0b

Ultra DMA33/66/100 (ATA 33/66/100) EIDE

Supports Wake-On-LAN (WOL)

Power-on by RTC alarm

Supports onboard hardware monitoring and includes Hardware DoctorTM utility

Supports three PC2100/PC1600 DDR SDRAM DIMMs up to 3GB memory space

SY-K7ADA

Supports multiple-boot function

5 x 32-bit bus mastering PCI slots fully compliant with PCI Rev2.2

1 x 32-bit AGP 1X/2X/4X sideband function slot, supports AGP specification V2.0

6 x USB ports onboard compliant with open HCI 1.0a specification

1 x IrDA port supports IrDA 1.0(SIR), IrDA1.1 (FIR) & Sharp-IR

ATX power connector

Easy CPU settings in BIOS with the “SOYO COMBO setup”

Supports Suspend to RAM and suspend to Disk

Supports on-board AC97 Audio

Supports CPU voltage adjustment by DIP switch

Supports CPU Multiplier selection by DIP switch

Supports CPU frequency adjustment by DIP switch

Quick Start Guide

SY-K7ADA Quick Start Guide

Hardware

Installation

Follow the directions in this section which is designed to guide you through a quick and correct method to install your new refer to the

the CD-ROM package that came with your Motherboard. Gather and prepare all necessary components to complete the installation successfully:

Installation

To avoid damage to your Motherboard, please follow these simple rules while

handling this equipment:

Before handling the Motherboard, ground yourself by touching an unpainted portion of the system's metal chassis.

Remove the Motherboard from its anti-static packaging. Hold the motherboard by the edges and avoid touching its components.

Check the Motherboard for damage. If any chip appears to be loose, press carefully to seat it firmly in its socket.

SY-K7ADA

SY-K7ADA Motherboard User's guide and Technical Reference

AMD® Socket462 processor with built-in CPU cooling fan (boxed type)

Motherboard. For detailed information, please

online manual in

DDR RAM module(s)

Computer case with adequate power supply unit

Monitor

PS/2 Keyboard

Pointing Device (PS/2 Mouse)

Speaker(s) (optional)

Disk Drives: HDD, CD-ROM, Floppy drive…

External Peripherals: Printer, Plotter, and Modem (optional)

Internal Peripherals: Modem and LAN cards (optional)

Note: 1.

If you want to use an external speaker connected to "Line-out" port, please make

sure to use an "amplified speaker" that can generate proper output sound volume.

SY-K7ADA

Hardware

Installation

Quick Start Guide

Install the Motherboard

To perform the installation of your new

Step 1. CPU Installation

Mark your CPU Frequency:

should be clearly marked on the CPU cover.

200MHz FSB Athlon CPU

750 MHz (100 x 7.5) 800 MHz (100 x 8.0) 850 MHz (100 x 8.5) 900 MHz (100 x 9.0) 950 MHz (100 x 9.5) 1000 MHz (100 x 10.0) 1.1GHz (100 x 11.0) 1.2 GHz (100 x 12.0)

1.3 GHz (100 x 13.0)

200MHz FSB Duron CPU

600 MHz (100 x 6.0) 650 MHz (100 x 6.5) 700 MHz (100 x 7.0) 750 MHz (100 x 7.5) 800 MHz (100 x 8.0) 850 MHz (100 x 8.5) 900 MHz (100 x 9.0)

266MHz FSB Athlon CPU

1 GHz (133 x 7.5) 1.13 GHz (133 x 8.5) 1.2 GHz (133 x 9.0) 1.33 GHz (133 x 10.0)

SY-K7ADA

Motherboard, follow the steps below:

Record the working frequency of your CPU that

CPU Mount Procedure:

To mount the AMD® & Athlon/DuronTM processor that you

have purchased separately, follow these instructions.

1. Lift the socket handle up to a vertical position.

2. Align the blunt edge of the CPU with the matching pinhole edge on the socket.

3. Seat the processor in the socket completely and without forcing.

4. Then close the socket handle to secure the CPU in place. Remember to connect the CPU Cooling Fan to the appropriate power

connector on the Motherboard.

The fan is a key component that stabilizes the system. It prevents the equipment from overheating and prolongs the life of your CPU.

SY-K7ADA Quick Start Guide

Hardware

Installation

Speaker

Step 2. Connections to the Motherboard

This section tells how to connect internal peripherals and the power supply to the Motherboard. The internal peripherals consist of IDE devices (HDD, CD-ROM), Floppy Disk Drive, Chassis

Fan, Front Panel Devices (Suspend LED Internal Speaker, Reset Button and IDE LED Switch.), Wake-On-LAN card, VGA card, Sound Card, and other devices.

For more details on connecting internal and external peripherals to your new SY-K7ADA Motherboard, please refer to

Reference

online manual on the CD-ROM.

SY-K7ADA Motherboard User's Guide and Technical

Connectors and Plug-ins

Standard IrDA (Infrared Device Header): SIRCON

Pin1 Pin2 Pin3 Pin4 Pin5 Pin6 Pin1 Pin2 Pin3

+5V FIR IRRX GND IRTX

OVCROFF

USB3_4: USB3 USB3_4: USB4

Pin1 Pin2 Pin3 Pin4 Pin6 Pin7 Pin8 Pin9 Pin10 +5V Data(-) Data(+) GND +5V Data(-) Data(+)

USB5_6: USB5 USB5_6: USB6

Pin1 Pin2 Pin3 Pin4 Pin6 Pin7 Pin8 Pin9 Pin10 +5V Data(-) Data(+) GND +5V Data(-) Data(+) GND GND

CPU Cooling Fan:

CPUFAN

Chassis Fan: CHAFAN

Pin1 Pin2 Pin3 Pin1 Pin2 Pin3 Pin1 Pin2 Pin3

GND +12V SENSOR PWM2 +12V SENSOR GND +12V NC

CD Line-in: CDIN1

Connect the CD Line-in cord from the CD-ROM device to the matching header CDIN1

1112131415161718

Pin11 Pin12 Pin13

LED NC GND

Pin17 Pin18 Pin19 Pin20

Power NC NC Speaker out

HDD LED PWRBT RESET Suspend LED

Pin9 Pin10 Pin4 Pin5 Pin1 Pin2 Pin7 Pin8

Power HDD LED PWRBTN GND Power RST GND Power SP_LED

ATX POWER On/Off : PWRBT

Connect your power switch to this header (momentary switch type).

To turn off the system, please press this switch and hold down for longer than 4 seconds.

Wake-On-LAN Header: JP10

5VSB GND PME #

GND GND

SYS Cooling Fan:

SYSFAN

Pin 1 Pin 2 Pin 3 Pin 4

CD_L GND GND CD_R

Power LED

SY-K7ADA

Hardware

Installation

123

Quick Start Guide

ATX Power Supply: ATX PW

Attach the ATX Power cable to this connector. (This motherboard requires an ATX power supply, an AT power supply can NOT be used.)

When using the Power-On by PS/2 Keyboard function, please make sure the ATX power supply is able to provide at least 720mA on the 5V Standby lead (5VSB) in order to meet the standard ATX specifications.

Step 3. Configure Memory

Supports PC2100/PC1600 DDR(Double Data Rate) SDRAM up to 3 DIMMs and using system memory up to 3GB. Supports symmetrical and asymmetrical DDR addressing.

Memory Configuration Table

Number of Memory Modules DIMM 1 DIMM 2 DIMM3

RAM Type DDR SDRAM

Memory Module Size 4/16/64/128/256/512 Mbit

Note: This Motherboard can only support 2 pcs of PC2100 DDR module, we suggest using DIMM1 and DIMM2 for PC2100 DDR module.

Step 4. Multiplier Adjustment Setting (RJ1)

For certain AMD CPUs, the multiplier is not locked such that setting a multiplier higher than specified on the CPU is possible. For technical details read the following:

Refer to the following table to set the Frequency Multiplier of your CPU.

Frequency Multiplier

Setting

Auto

Manual

Short Pin1-2 Short Pin1-2

Short Pin2-3 Short Pin2-3

RJ2 RJ3

SY-K7ADA Quick Start Guide

Hardware

Installation

123

If you set ratio to manual and configure the RJ1 DIP switch to the settings that match your CPU speed, as follow table:

RJ1 1 2 3 4 RJ1 1 2 3 4

5 On On

Off

5.5 6 On

Off Off Off

6.5 7 On On On

Off

7.5 8 On

Off Off

8.5

Note: SOYO does not guarantee system stability if the user over clocks the system. Any malfunctions due to over-clocking are not covered by the warranty.

Off Off

On On

Off

On On

On 9 On On On 9.5

Off

On 10 On On 10.5

Off Off

11.5

Off Off

12.5

Off Off Off Off

11 On On On On

Off

12 On

Off Off

Off Off Off Off

Off Off Off

On On On

Off

On On On On

Step 5. Enable/Disable Power-On by Keyboard (JP1)

You may choose to enable the Power-On through Keyboard function by shorting pin 2-3 on jumper JP1; or short pin 1-2 to disable this function.

Power-On by

Keyboard

Short pin 2-3 to

JP1 Setting

Important: When using the Power-On by Keyboard function, please make sure the ATX power supply is able to provide at least 720mA on the 5V Standby lead (5VSB) in order to meet the standard ATX specification.

enable the Power-

On by Keyboard

Enable Disable

Short pin 1-2 and the Power-On by

Keyboard function is

function.

disabled.

Step 6. The synchronous / asynchronous clock mode between CPU

and memory interface setting

The FSB Frequency can also be set through DIP switch FJ1 or BIOS and it may therefore differ from the Frequency the CPU specifies. Doing so may however force your CPU to operate out of its specifications and therefore SOYO can not guarantee the proper functioning of your system.

Refer to the following table:

SY-K7ADA

Hardware

Installation

CPU Freq(MHz)

SDRAM(MHz)

123

100

100OnOn

Off

133

Off

123

FJ1– CPU frequency setting

Quick Start Guide

Step 7. CPU Vcore adjustment (VJ1)

Refer to following table to set the voltage of your CPU. If you set VJ2 status to AUTO, please set VJ1 switch status to Off (all).

Status Setting VJ2

Manual

Auto

If you set status to manual and configure VJ1 switch to the settings that match your CPU voltage as follow table:

VJ1

Auto OFF OFF OFF OFF OFF 1.475

1.100

1.125

1.150

1.175

1.200

1.225

1.250

1.275

1.300

1.325

1.350

1.375

1.400

1.425

1.450

1 2 3 4 5

ON OFF OFF OFF OFF

OFF ON OFF OFF OFF

ON ON OFF OFF OFF

OFF OFF ON OFF OFF

ON OFF ON OFF OFF

OFF ON ON OFF OFF

ON ON ON OFF OFF

OFF OFF OFF ON OFF

ON OFF OFF ON OFF

OFF ON OFF ON OFF

ON ON OFF ON OFF

OFF OFF ON ON OFF

ON OFF ON ON OFF

OFF ON ON ON OFF

ON ON ON ON OFF

Short Pin2-3

Short Pin1-2

VJ1

1.500

1.525

1.550

1.575

1.600

1.625

1.650

1.675

1.700

1.725

1.750

1.775

1.800

1.825

1.850

1 2 3 4 5

OFF OFF OFF OFF ON

ON OFF OFF OFF ON

OFF ON OFF OFF ON

ON ON OFF OFF ON

OFF OFF ON OFF ON

ON OFF ON OFF ON

OFF ON ON OFF ON

ON ON ON OFF ON

OFF OFF OFF ON ON

ON OFF OFF ON ON

OFF ON OFF ON ON

ON ON OFF ON ON

OFF OFF ON ON ON

ON OFF ON ON ON

OFF ON ON ON ON

ON ON ON ON ON

SY-K7ADA Quick Start Guide

Hardware

Installation

123

CMOS Clear (JP5)

In some cases the CMOS memory may contain wrong data, follow the steps below to clear the CMOS memory.

1. Clear the CMOS memory by momentarily shorting pin 2-3 on jumper JP5. This jumper can be easily identified by its white colored cap.

2. Then put the jumper back to 1-2 to allow writing of new data into the CMOS memory.

CMOS Clearing

JP5 Setting

Clear CMOS Data Retain CMOS Data

Short pin 2-3 for

at least 5 seconds to

Short pin 1-2 to

retain new settings

clear the CMOS

Note: You must unplug the ATX power cable from the ATX power connector when performing the CMOS Clear operation.

SY-K7ADA

Quick BIOS

This Motherboard does not use any hardware jumpers to set the CPU frequency. Instead, CPU settings are software configurable with the BIOS

[SOYO COMBO SETUP] combines the main parameters that you need to configure, all in one menu, for a quick setup in BIOS.

Quick BIOS Setup

[SOYO COMBO SETUP].

Quick Start Guide

The

After the hardware installation is complete, turn the power switch on, then press the during the system diagnostic checks to enter the Award BIOS Setup program. The CMOS SETUP UTILITY will be shown on the screen. Then, follow these steps to configure the CPU settings.

Step 1. Select [STANDARD CMOS SETUP]

Set [Date/Time] and [Floppy drive type], then set [Hard Disk Type] to “Auto”.

Step 2. Select [LOAD SETUP DEFAULT]

Select the “LOAD SETUP DEFAULT” menu and type “Y” at the prompt to load the BIOS optimal setup.

Step 3. Select [SAVE & EXIT SETUP]

<Enter>

Press sequence.

to save the new configuration to the CMOS memory, and continue the boot

<DEL>

key

Setup

SY-K7ADA

The SOYO CD

The SOYO-CD will NOT autorun if you use it on an Operating System other than Windows 9x or NT.

Your SY-K7ADA Motherboard comes with a CD-ROM labeled "SOYO CD." The SOYO CD contains (1) the user's manual file for your new Motherboard, (2) the drivers/software available for installation, and (3) a database in HTML format with information on SOYO Motherboards and other products.

Step 1. Insert the SOYO CD into the CD-ROM drive

If you use Windows NT, the SOYO-CD will not detect your motherboard type. In that case the following dialog will pop up, please choose your motherboard and press OK. Now the SOYO-CD Start Up Menu will be shown.

Quick Start Guide

The SOYO CD

Please Select Your Board

7IWA-F 7IWA-F V1.0 6IWM/L 6IWM 6IWA

(SOYO CD Start Up Program Menu)

If you use Windows 95 or 98, the SOYO CD Start Up Program automatically detects which SOYO Motherboard you own and displays the corresponding model name.

LI-7000 7IWB 7IWB V1.0 7IWM 7IWM/L V1

Cancel

SY-K7ADA

The SOYO CD

The user's manual files included on the SOYO CD are in PDF (Postscript Document) format. In order to read a PDF file, the appropriate Acrobat Reader software must be installed in your system.

Quick Start Guide

Note:

The Start Up program automatically detects if the Acrobat Reader utility is already present in your system, and otherwise prompts you on whether or not you want to install it. You must install the Acrobat Reader utility to be able to read the user's manual file. Follow the instructions on your screen during installation, then once the installation is completed, restart your system and re-run the SOYO CD.

Step 2. Install Drivers and Utilities

Click the with your Motherboard. The Start Up program displays the drivers available for the particular model of Motherboard you own. We recommend that you only install those drivers.

Install Drivers

button to display the list of drivers/ software that can be installed

SY-K7ADA

The SOYO CD

driver revision:

ALi AGP Driver for win 9x/2000 ALi Onboard Audio Driver for win 9x/2000 ALi Onboard Audio Driver for win NT4.0 ALi Hardware monitor(R) Driver for win 9x/98ME ALi Hardware monitor(R) Driver for win NT/2000

Quick Start Guide

Cancel

(Driver Installation Menu)

A short description of all available drivers follows:

Ø ALi AGP driver for Win 9x/2000

The ALi AGP driver package includes below drivers your motherboard needs. After selecting this driver package, one driver will be installed automatically. A description of the 2 drivers follows:

 ALi IDE driver

This driver will speed up the data-transfer rate to and from the harddisk.

 ALi AGP Driver

This driver must be installed in order to be able to make use of the AGP Video functionality.

Ø ALi Onboard Audio Driver for win 9x/2000

You have to install the drivers before installing any application for the Onboard Audio.

Ø ALi Onboard Audio Driver for win NT4.0

You have to install the drivers before installing any application for the Onboard Audio.

Ø ALi hardware monitor(R) for win 9x/98ME

Your motherboard comes with a hardware monitoring IC. By installing this utility Temperature, Fan speed and Voltages can be monitored. It is also possible to set alarms when current system values exceed or fall below pre-set values.

Ø ALi hardware monitor(R) for win NT/2000

SY-K7ADA

The SOYO CD

Quick Start Guide

Select which driver you want to install and click installation and return to the main menu.

Note:

Once you have selected a driver, the system will automatically exit the SOYO CD to begin the driver installation program. When the installation is complete, most drivers require to restart your system before they can become active.

OK,

or click

Cancel

to abort the driver

Step 3.

1.For supporting S3 mode wake up function in WINDOWS 98se, please download the driver from SOYO web site (www.soyo.com.tw). Please put this downloaded driver in c:\windows\system32\driver and remove USB device in “Device Manager” then refresh.

Please put this downloaded driver in c:\windows\system32\driver

SY-K7ADA

The SOYO CD

Quick Start Guide

Remove USB device(ex : USB keyboard, mouse,…,etc.)

Refresh

SY-K7ADA

The SOYO CD

Final

2.If customer uses the WINDOWS 95 OSR2, please use the NT version driver

when installing audio driver.

Quick Start Guide

3.Right now, ALI chipset does not support ATI RAGE 128 graphics chip, so K7ADA

can not support this kind of VGA card.

Step 4. Check the Latest Releases

Click the 'Check the latest Releases' button to go the SOYO Website to automatically find the latest BIOS, manual and driver releases for your motherboard. This button will only work if your computer is connected to the internet through a network or modem connection. Make sure to get your modem connection up before clicking this button.

(* Internet Explorer is a Microsoft Trademark)

SY-K7ADA

Quick Start Guide

Quick Trouble shoot tips

Video (no display) related issues

I built a new computer system using a Soyo board and nothing happens when turning it on, no video and no beeps from the PC speaker. What is happening and how can it be fixed?

No screen and no beeps mean that your CPU and motherboard do not work at all. It could be that the CPU is not seated correctly or that a component on the M/B is grounded (shorted) with the case. Also make sure to check the voltage setting switch (110V/220V) on the back of the power supply. To isolate the problem do the following:

1. Press and hold down on the “Ins” (insert) key while turning on the computer until you get video. If you do not get video then,

2. Double-check jumpers setting on you motherboard and remove all add-on cards, unplug all hard-disk and floppy-disk drive cables and see if you can hear some beeps. If you still do not get any beeps, then try putting the motherboard on the table (to isolate it from the case) with the CPU and speaker only, and give it one more try.

I hear a series of beeps and I do not get anything from my monitor. What could be wrong?

The following lists some basic beep codes and their possible meanings:

• One long beep and 3 very short beeps - The video card is not detected by

the motherboard. Please re-seat your video card. If you are using an AGP card, please push your AGP card down real hard. You may have to push VERY hard without the AGP card mounting screw. Make sure not to insert the card the other way around.

• Continuous beeps – One or more of the memory modules is not seated

correctly in its socket.

My PCI VGA card works fine with my system, but when I put in a new AGP card, it does not give me any video. Is my AGP slot bad?

This is a common problem with AGP video cards. The reason is that your AGP card did not get seated into the AGP slot fully and firmly. Please push your AGP card down into the socket real hard, it should snap twice. You may have to unscrew the AGP card to allow the card to go further down. Do take care not to damage the card by using too much force.

SY-K7ADA

I get distorted video my AGP card right after I save my bios. Why is that?

The cause is likely that your AGP card is not running at the correct bus speed. To fix this, please clear the CMOS via JP5 and if it still does not work, please upgrade your motherboard bios to the latest version.

Quick Start Guide

BIOS Issues

Where can I find the BIOS revision of my mainboard?

It will be displayed on the up-left corner on the screen during boot-up. It will show as your board type followed by the revision number, such as 5EH_2CA1 (meaning revision 2CA1 for the SY-5EH board) or 6BA+ IV_2AA2 which means SY-6BA+ IV motherboard with 2AA2 bios.

Where can I find the latest BIOS of my motherboard?

Please go to the technical support page of one of the SOYO websites (Taiwan:

www.soyo.com.tw), and look up your motherboard to find the latest BIOS

revision.

Hard disk, floppy drive, CD-ROM etc

When I boot up my new computer I got "floppy boot failure" and the LED on the floppy stays on

Make sure the red wire of floppy ribbon cable goes to Pin1 on the floppy drive side (don't trust the "key lock" or "notch") and use the end-connector of the cable (don't use middle one).

Modem issues

I get an "I/O Conflict" message when I turn on my system and I can not get my modem to work

What you need to do is to disable 'COM2' (or UART2 or serial port 2) in the bios under integrated peripheral setup.

I have installed my modem drivers several times and I still cannot get my modem to work. Why?

If you are sure that the modem driver has been installed correctly, then you need to install the via 4 in 1 driver from the SOYO CD, this is because Windows does not properly recognize relatively new chipsets.

I can not get my board to run properly.

Please make sure you have the latest bios and driver from the SOYO web site at:

http://www.soyo.com

SY-K7ADA

How to contact us:

n If you are interested in our products, please contact the SOYO sales

department in the region you live.

n If you require Technical Assistance, please contact our Technical Support in

the region you live. SOYO prefers Email as communication medium, remember to always add to the email the country that you live in.

Quick Start Guide

TAIWAN

SOYO COMPUTER INC. No. 21 Wu-Kung 5 Rd., Hsin Chuang

City, Taipei Hsien, Taiwan, R.O.C TEL: 886-2-22903300 FAX: 886-2-22983322

http://www.soyo.com/

Email: info@mail.soyo.com

USA

SOYO INC. 41484 Christy Street, Fremont, CA

94538, USA TEL: 1-510-226-7696 FAX: 1-510-226-9218

http://www.soyousa.com/

Email : sales@soyousa.com

SOYO Deutschland GmbH (SAAT Technology GmbH)

August-Wilhelm-Kuhnholz-Str. 15 D-26135 Oldenburg (Oldb), Germay

TEL: 49-441-209-100 FAX: 49-441-203-442

http://www.soyo.de/

Email: sales@soyo.de

JAPAN

SOYO COMPUTER SOYO BLDG, 1-23-14, Hyakunincho,

Shinjyuku-ku, Tokyo Japan 169-0073 TEL: 81-3-3368-2188 FAX: 81-3-3368-2199

http://www.soyo.co.jp/

Email: support@soyo.co.jp

CHINA

GING MEI JEI LTD Room 304, Phoenix Mansion, No. 165

Haidian Road, Haidian Distnct, Beijing 100080, China

TEL: 86-10-6251-0089 FAX: 86-10-6251-0311

http://www.soyo.com.cn/

Email: soyo@public.bat.net.cn

KOREA

SOYO TECHNOLOGY CO., LTD. 3 rd, F1, Wonhyo Bldg, 46-1,

Wonhyoro 3 Ga, yongsan Ku, Seoul Korea

TEL: 882-716-2850 FAX: 882-704-2619

http://www.soyo.co.kr/

Email: soyo@soyo.co.kr

Hong Kong

Soyo (H.K.) Ltd. 5C, Big Star Centre, 8 Wang Kwong

Road, Kowloon Bay, Kowloon, HK TEL: 852-2710-9810 FAX: 852-2710-9078

http://www.soyo.com.hk/

Email: soyo@hkstar.com

SY-K7ADA

Quick Start Guide

Edition: May 2001

Version 1.2

SY- K7ADA

SERIAL

SOYO SY-K7ADA User Manual 2

Specifications and Main Features

Frequently Asked Questions

User Manual