Southbend P32D-171 General Manual

INFRARED BROILER WITH

OVERHEAD WARMING OVEN

AND SECTIONAL BASE

Standard Features

• 104,000 BTU (NAT or LP) infra-red burners

• Stainless steel front, sides and back

• 90 second preheat with no waiting between loads

• Rugged grid height adjustment mechanism with four positions

• Fully insulated lining and burner boxes

• Broiler grid is 24-1/2” wide and 28” deep -easily rolls out 17-1/4”

• 6” adjustable legs

• 1-1/4” font manifold and rear gas connection standard

• Warranty: two years on specified operational parts and one year
on labor from date of purchase

Standard Features of Oven Bases

• 45,000 BTU NAT (42,000 BTU LP) oven with electronic pilot
ignition

• Cool-to-the-touch handle

• Porcelain enamel interior

• 2 oven racks with Standard and 3 racks with Convection

• “Insta-On” thermostat ranging from 150

• Standard oven interior is large enough to fit 26” x 26” sheet pan
either way

• Convection oven models have 1/3hp, two speed blower

• NEMA 4 water resistant controls

°F to 500°F

P32D-171 (Standard Oven Base)

P32A-171 (Convection Oven Base)

Job Item#

Warming Oven

• Model P32-171 has a warming oven that is heated by broiler flue
gases (25” wide x 25” deep). 3,000 watt electric heating
element optional.

STANDARD CONSTRUCTION SPECIFICATIONS

Exterior Finish: Top, front, sides and back are 430 stainless

steel #3 polish.

Broiler: Infrared broiler with overhead warming oven.
104,000 BTU (NAT or LP) broiler burners with separate
controls. Fully insulated lining and burner box. Roll-out
broiler grid is 24-1/2” wide and 28” deep (rolls out to 17-1/4”),
with four height positions.

Battery: Position in battery -left, right or on end. If the item
is at the end of a battery, the end side will be solid (rather
than have a coverplate over the end of the front manifold).

Legs: Stainless steel 6” adjustable legs standard.

(Model P32D-171 )

Warming Oven: 25” wide and 25” deep oven, located on top of
broiler, is heated by the broiler flue gases. 3,000 watt electric
heating element optional.

Model 32D: 45,000 BTU NAT (42,000 BTU LP) with electronic
ignition and thermostat range of 150°F to 500°F. Porcelain
enamel interior, measuring 14” high x 26” wide x 26-1/2” deep.
Two racks with 5-position side rails.

Model 32A: 45,000 BTU NAT (42,000 BTU LP) convection
oven with electronic ignition and thermostat range of 150°F to
500°F. Porcelain enamel interior, measuring 14” high x 26”
wide x 24” deep. Three racks with 5-position side rails. Two­speed, 1/3 hp blower motor.

Form P32-171 Rev 1 (01/07)

www.yatesgd.com www.yatesgraphicdesign.com

Printed in USA

Models:

P32N-171 P32A-171

SHIPPING CRATE DIMENSIONS & WEIGHT

MODE L WIDTH HEIGHT DEPTH VOLUME WEIGHT

45.5"

83"

55"

P32D-171

P32A-171

DImensions shown in inches and (millimeters)

(1156)

45.5"

(1156)

(2108)

83"

(2108)

(1397)

55"

(1397)

120 .2 cu ft

(3.40 cu m)

120 .2 cu ft

(3.40 cu m)

860 lbs

(390.1 kg)

916 lbs

(415.5 kg)

UTILITY INFORMATION

GAS: Each unit has a 1-1/4” front

gas manifold that couples to the
adjacent sectional unit(s), and a 1”
rear gas connection with a male
NPT connector. Minimum supply
pressure is 7” W.C. for natural gas

MODEL

P32D-171 149,000 146,000 1.0

P32A-171 149,000 146,000 4.8

and 11” W.C. for propane. All
sectional units require a regulated gas supply; pressure regulator to be ordered
separately. If using a flexible hose gas connection, the I.D. of the hose must not
be smaller than the connector on the unit and must comply with ANSI Z21.69,
providing an adequate means of restraint to prevent undue strain on the gas
connection.
ELECTRICITY: Both standard and convection oven models require 50Hz or
60Hz single phase. 120V models have a 7ft. power cord with ground plug. 208/
240V models have a terminal block for connection to a single phase 208/240V
source.

NOTE: An optional electric element rated at 3,000 watts, 208/236V, is available in the
warming oven. A separate electric supply, 208/236V single phase, 20 AMP must be
connected to the leads in a terminal box at the rear, near top of broiler. Installation must
conform with local codes.

GAS (B TU/HR)ELE CTRI CITY (AMPS)

NATURAL PROPANE 120V 208/240V

1.0

(se e no te)

2.6

(se e no te)

OPTIONS AND ACCESSORIES

❑ Additional oven rack

❑ Cable restraint kit (to restrict movement when

on casters)

MISCELLANEOUS

- If casters are used with flex hose, a restraining device
should be used to eliminate undue stain on the flex
hose.

- Minimum clearance from noncombustible construction is
zero (blower of convection oven model requires 2” rear
clearance). Minimum clearance from combustible
construction is 6” on sides and 6” on rear.

- Install under vented hood.

- Check local codes for fire and sanitary regulations.

NOTICE: Southbend has a policy of continuous product
research and improvement. We reserve the right to change
specifications and product design without notice. Such
revisions do not entitle the buyer to corresponding changes,
improvements, additions or replacements for previously
purchased equipment.

❑ Casters -front two casters lock

❑ Open-frame base with casters

❑ 3,000 watt heating element for warming oven

INTENDED FOR COMMERCIAL USE ONLY.

NOT FOR HOUSEHOLD USE.

Form P32-171 Rev 1 (01/07)

1100 Old Honeycutt Road, Fuquay-Varina, NC 27526

[phone] www.southbendnc.com

www.yatesgd.com www.yatesgraphicdesign.com