Southbend P32C-32B, P32D-3240 General Manual

A Middleby Company

RADIANT BROILER WITH

OVERHEAD WARMING OVEN

AND SECTIONAL BASE

Standard Features

- 110,000 BTU -two broiler burnerswith seperate controls

- Stainless steel front and sides

- Removable drip drawer

- Rugged grid height adjustment mechanism with four
positions

- Warming oven -heated by broiler flue gases (25” wide x
25” deep)

- Fully insulated lining and burner boxes

- Broiler grid is 24 1/2” wide and 28” deep -easily rolls out
17 1/4”

- 6” adjustable legs

- 1 1/4” font manifold and rear gas connection standard

- Warranty: two years on specified operational parts and
one year on labor from date of purchase

Standard Features of Oven Bases

- 45,000 BTU oven with electronic pilot ignition

- Cool-to-the-touch handle

- Porcelain enamel interior

- 2 oven racks with Standard and 3 racks with Convection

- “Insta-On” thermostat ranging from 150

- Standard oven interior is large enough to fit 26”x26”
sheet pan either way

- Convection oven models have 1/3hp, two speed blower

°F to 500°F

P32C-32B (Cabinet Base)

P32D-3240 (Standard Oven Base)

P32A-3240 (Convection Oven Base)

Job Item#

Standard Features of Cabinet-Base Models

- Stainless steel cabinets with dual side by side removable
doors

STANDARD CONSTRUCTION SPECIFICATIONS

Exterior Finish: Top, front, and sides are 430 stainless steel

#3 polish. Aluminized steel back.

Broiler: Radiant broiler with overhead warming oven. Two
radiant broiler burners with seperate controls -total BTU:
110,000. Fully insulated lining and burner box. Roll-out
broiler grid is 24 1/2” wide and 28” deep (rolls out to 17 1/4”),
with four height posistions.

Battery: Position in battery -left, right or on end. If the item is
at the end of a battery, the end side will be solid (rather than
have a coverplate over the end of the front manifold).

Legs: Stainless steel 6” adjustable legs standard.

Warming Oven: 25” wide and 25” deep oven, located on top

of broiler, is heated by the broiler flue gases.

(Model P32C-32B)

Model 32D: 45,000 BTU with electronic ignition and
thermostat range of

measuring 14” high x 26” wide x 26.5” deep. Two racks with 5­position side rails.

Model 32A: 45,000 BTU convection oven with electronic
ignition and thermostat range of 150°F to 500°F. Porcelain

enamel interior, measuring 14” high x 26” wide x 24” deep.
Three racks with 5-position side rails. Two-speed, 1/3 hp
blower motor.

Model 32C: Stainless steel cabinet base with removable doors
that open from the center.

150°F to 500°F. Porcelain enamel interior,

Form P32-3240

A Middleby Company

07/04 Printed in USA

Models:

P32C-32B P32A-3240 P32A-3240

38-3/4"

(984)

3-3/4"

(95)

32" (813)

41-3/4" (1060)

32" (813)

36"

(914)

45"

(1143)

57-3/4"

(1467)

72"

(1829)

75"

(1905)

2-1/2" (64)

33-3/4"

(859)

35-3/4" (908)

Front Gas Manifold

ledoMhtdiWthgieHhtpeDemuloVthgieW

5.54

38

)6511(

)8012(

5.54

38

)6511(

)8012(

5.54

38

)6511(

)8012(

7" (178)

Motor for

Convection

Oven Model

B23-C23P

0423-D23P

0423-A23P

Flue riser for “deep” depth-option extends rearward 6"
(cooking areas are same as for “standard” depth).

Optional

Rear Gas

Connection

20"

(508)

55

)8931(

55

)8931(

55

)8931(

2-1/2" (64)

THGIEW&SNOISNEMIDETARCGNIPPIHS

tfuc2.021

)muc04.3(

tfuc2.021

)muc04.3(

tfuc2.021

)muc04.3(

Electrical

Connection

for Oven

Models

18"

(457)

sbl553

)gk161(

sbl619

)gk514(

sbl559

)gk334(

UTILITY INFORMATION

GAS: Each unit has a 1 1/4”

front gas manifold that couples
to the adjacent sectional unit(s),
and a 1” rear gas connection with
a male NPT connector.
Minimum supply pressure is 7”
W.C. for natural gas and 11”
W.C. for propane. All sectional units require a regulated gas supply;
pressure regulator to be ordered separately. If using a flexible hose gas
connection, the I.D. of the hose must not be smaller than the connector
on the unit and must comply with ANSI Z21.69, providing an adequate
means of restraint to prevent undue strain on the gas
connection.
ELECTRICITY: Both standard and convection oven models require 50Hz
or 60Hz single phase. 120V models have a 7ft. power cord with ground
plug. 208/240V models have a terminal block for connection to a single
phase 208/240V source.

SAGYTICIRTCELE

larutaN

enaporP

ledoM

ruoH/UTB

B23-C23P000,011000,09--

0423-D23P000,551000,2310.10.1

0423-A23P000,551000,2318.46.2

V021

ruoH/UTB

spmA

V042/802

spmA

OPTIONS AND ACCESSORIES

Cable restraint kit (to restrict movement

Stainless steel back

T

Additional oven rack

T

T

when on casters)

Casters -front two casters lock

T

MISCELLANEOUS

- If casters are used with flex hose, a restraining device
should be used to eliminate undue stain on the flex hose.

- Minimum clearance from noncombustible construction is
zero (blower of convection oven model requires 2” rear
clearance). Minimum clearance from combustible construction
is 6” on sides and 6” on rear.

- Install under vented hood.

- Check local codes for fire and sanitary regulations.

NOTICE:

Southbend has a policy of continuous product research and
improvement. We reserve the right to change specifications
and product design without notice. Such revisions do not
entitle the buyer to corresponding changes, improvements,
additions or replacements for previously purchased
equipment.

Open-frame base with casters

T

Form P32-3240

INTENDED FOR COMMERCIAL USE ONLY.

NOT FOR HOUSEHOLD USE.

1100 Old Honeycutt Rd., Fuquay-Varina, NC 27526

www.southbendnc.com