Southbend P32A-171 General Manual

A Middleby Company

INFRARED BROILER WITH

OVERHEAD WARMING OVEN

SECTIONAL BASE

AND

Standard Features

- 104,000 BTU Schwank infra-red burners

- Stainless steel front and sides

- 90 second preheat with no waiting between loads

- Rugged grid height adjustment mechanism with four
positions

- Warming oven -heated by broiler flue gases (25” wide x
25” deep)

- Fully insulated lining and burner boxes

- Broiler grid is 24 1/2” wide and 28” deep -easily rolls out
17 1/4”

- 6” adjustable legs

- 1 1/4” font manifold and rear gas connection standard

- Warranty: two years on specified operational parts and
one year on labor from date of purchase

Standard Features of Oven Bases

- 45,000 BTU oven with electronic pilot ignition

- Cool-to-the-touch handle

- Porcelain enamel interior

- 2 oven racks with Standard and 3 racks with Convection

- “Insta-On” thermostat ranging from 150

- Standard oven interior is large enough to fit 26”x26”
sheet pan either way

- Convection oven models have 1/3hp, two speed blower

°F to 500°F

P32D-171 (Standard Oven Base)

P32A-171 (Convection Oven Base)

Job Item#

STANDARD CONSTRUCTION SPECIFICATIONS

Exterior Finish: Top, front, and sides are 430 stainless steel

#3 polish. Aluminized steel back.

Broiler: Infrared broiler with overhead warming oven.
104,000 BTU Schwank broiler burners with separate controls.
Fully insulated lining and burner box. Roll-out broiler grid is
24 1/2” wide and 28” deep (rolls out to 17 1/4”), with four
height positions.

Battery: Position in battery -left, right or on end. If the item is
at the end of a battery, the end side will be solid (rather than
have a coverplate over the end of the front manifold).

Legs: Stainless steel 6” adjustable legs standard.

Form P32-171

A Middleby Company

(Model P32D-171 )

Warming Oven: 25” wide and 25” deep oven, located on top
of broiler, is heated by the broiler flue gases.

Model 32D: 45,000 BTU with electronic ignition and thermo­stat range of 150°F to 500°F. Porcelain enamel interior,

measuring 14” high x 26” wide x 26.5” deep. Two racks with 5­position side rails.

Model 32A: 45,000 BTU convection oven with electronic
ignition and thermostat range of 150°F to 500°F. Porcelain

enamel interior, measuring 14” high x 26” wide x 24” deep.
Three racks with 5-position side rails. Two-speed, 1/3 hp
blower motor.

07/04 Printed in USA

Models:

P32N-171 P32A-171

THGIEW&SNOISNEMIDETARCGNIPPIHS

32" (813)

36"

(914)

38-3/4"

2" (51)

45-1/2"

(1156)

(984)

59-1/4"

(1505)

78-1/4"

(1988)

81"

(2057)

2-1/2" (64)

33-3/4"

(859)

41-3/4" (1060)

37" (940)

Front Gas Manifold

ledoMhtdiWthgieHhtpeDemuloVthgieW

5.54

38

55

)8012(

)8931(

38

55

)8012(

)8931(

7" (178)

2-1/2" (64)

Motor for

Convection

Oven Model

171-D23P

171-A23P

)6511(

5.54
)6511(

Flue riser for “deep” depth-option extends rearward 4-1/4"
(cooking areas are same as for “standard” depth).

Rear Gas

Connection

20"

(508)

tfuc2.021
)muc04.3(

tfuc2.021
)muc04.3(

Electrical

Connection

for Oven

Models

18"

(457)

sbl068

)gk093(

sbl619

)gk614(

UTILITY INFORMATION

GAS: Each unit

has a 1 1/4”
front gas
manifold that

ledoM

couples to the
adjacent
sectional
unit(s), and a

171-D23P000,941000,6410.10.1

171-A23P000,941000,6418.46.2

1” rear gas
connection with a male NPT connector. Minimum supply pressure is 7” W.C.
for natural gas and 11” W.C. for propane. All sectional units require a regulated
gas supply; pressure regulator to be ordered separately. If using a flexible
hose gas connection, the I.D. of the hose must not be smaller than the
connector on the unit and must comply with ANSI Z21.69, providing an
adequate means of restraint to prevent undue strain on the gas
connection.
ELECTRICITY: Both standard and convection oven models require 50Hz or
60Hz single phase. 120V models have a 7ft. power cord with ground plug.
208/240V models have a terminal block for connection to a single phase 208/
240V source.

SAGYTICIRTCELE

larutaN

ruoH/UTB

enaporP

ruoH/UTB

V021

spmA

V042/802

spmA

OPTIONS AND ACCESSORIES

Stainless steel back

T

Additional oven rack

T

Cable restraint kit (to restrict movement

T

when on casters)

Casters -front two casters lock

T

MISCELLANEOUS

- If casters are used with flex hose, a restraining device
should be used to eliminate undue stain on the flex hose.

- Minimum clearance from noncombustible construction is
zero (blower of convection oven model requires 2” rear
clearance). Minimum clearance from combustible
construction is 6” on sides and 6” on rear.

- Install under vented hood.

- Check local codes for fire and sanitary regulations.

NOTICE:

Southbend has a policy of continuous product research
and improvement. We reserve the right to change
specifications and product design without notice. Such
revisions do not entitle the buyer to corresponding
changes, improvements, additions or replacements for
previously purchased equipment.

Open-frame base with casters

T

INTENDED FOR COMMERCIAL USE ONLY.

NOT FOR HOUSEHOLD USE.

Form P32-171

1100 Old Honeycutt Rd., Fuquay-Varina, NC 27526

www.southbendnc.com