Soundmax SM-CCR3050F User Manual [ru]

SM-CCR3050F

USB/SD media player USB/SD-медиаплеер Instruction manual Руководство по эксплуатации

Dear customer!

Thank you for purchasing our product. For safety, it is strongly recommended to read this manual carefully before connecting, operating and/or adjusting the product and keep the manual for reference in the future.

Table of contents

TABLE OF CONTENTS ...................................................................................................................................................... 2

IMPORTANT SAFEGUARDS ............................................................................................................................................ 3

ACCESSORIES .................................................................................................................................................................... 4

INSTALLATION/CONNECTION ...................................................................................................................................... 5

CONTROL ELEMENTS ....................................................................................................................................................... 9

GENERAL OPERATIONS .................................................................................................................................................. 10

RADIO OPERATIONS ........................................................................................................................................................ 12

USB/SD OPERATIONS ..................................................................................................................................................... 13

TROUBLESHOOTING GUIDE .......................................................................................................................................... 15

SPECIFICATION ................................ ................................................................................................................................ . 16

Important safeguards

Read carefully through this manual to familiarize yourself with this high-quality sound system. The beginning of operation is the moment of the unit installation. Before use the device in winter it is

recommended to heat up the passenger compartment during 20 seconds or to the operation temperature.

Use the unit with the temperature that goes beyond the operation temperature greatly decreases the

operation resource of the screen and other components of device and can result an outage.

Disconnect the vehicle's negative battery terminal while mounting and connecting the unit. When replacing the fuse, be sure to use one with an identical amperage rating. Using a fuse with a higher

amperage rating may cause serious damage to the unit.

Make sure that pins or other foreign objects do not get inside the unit; they may cause malfunctions, or

create safety hazards such as electrical shock.

Do not use the unit in places where it can be exposed to water, moisture and dust. Do not open covers and do not repair yourself. Consult the dealer or an experienced technician for help. Make sure you disconnect the power supply and aerial if you will not be using the system for a long period

or during a thunderstorm.

Make sure you disconnect the power supply if the system appears to be working incorrectly, is making an

unusual sound, has a strange smell, has smoke emitting from it or liquids have got inside it. Have a qualified technician check the system.

The unit is designed for negative terminal of the battery, which is connected to the vehicle metal. Please

confirm it before installation.

Do not allow the speaker wires to be shorted together when the unit is switched on. Otherwise it may

overload or burn out the power amplifier.

Accessories

1. Receiver 1 pc

2. Mounting parts: Hexagon nut 1 pc Mounting sleeve 1 pc Release keys 2 pcs Metal bar 1 pc Plain washer 1 pc Spring washer 1 pc Self-tapping screw 1 pc Screw 4 pc

3. ISO-connector 2 pcs

4. Consumer information 1 pc

5. Warranty card 1 pc

6. Instruction manual 1 pc

Installation/Connection

General notes

Choose the mounting location where the unit will not interfere with the normal driving function of the

driver.

Before finally installing the unit, connect the wiring and make sure that the unit works properly. Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the

vehicle.

Install the unit where it does not get in the driver's way and cannot injure the passenger if there is a

sudden stop, like an emergency stop.

Avoid installing the unit where it would be subject to high temperature, such as from direct sunlight, or

from hot air, from the heater, or where it would be subject to dust, dirt or excessive vibration.

DIN FRONT-MOUNT

1. Car dashboard

2. Sleeve

3. Bolt

4. Nut

5. Spring washer

6. Screw

7. Metal strap

8. Flat washer

1. Install the sleeve into the dashboard; ensure it is installed with the correct side and there are no

obstacles (wires, dashboard elements, etc) for the unit installation.

2. After installing the sleeve into the dashboard, bend tabs fitting to the size of the dashboard to fix the

sleeve in place.

3. Use the metal strap to fix the rear side of the unit. Determine a place for fixing and install the strap as

shown in the picture. You can bend the strap to the needed angle with your hands.

4. Make the necessary wire connections. Ensure the connections are correct.

5. Install the unit into the sleeve until the side locks are fixed.

Dismantling the unit

1. Make sure the ignition is turned off, then disconnect the cable from the vehicle battery’s negative (-) terminal.

2. Remove the metal strap attached the back of the unit (if attached).

3. Insert both of the supplied keys into the slots at the middle left and right sides of the unit, then pull the unit out of the dashboard.

Connection diagram

Notes:

In spite of having any kinds of speaker system, must use 4 ohms impedance of speaker to reduce the

distortion during high volume level.

It is prohibited making the conductors of auto antenna and ground touch with each other.

Using the ISO Connector

Location

Function

Connector A

Connector B

1 - Rear Right (+)---Violet

2 - Rear Right (-)---Violet/Black

3 - Front Right (+)---Grey

Battery 12V (+)/Yellow

Front Right (-)---Grey/Black

Auto Antenna/Blue

Front Left (+)---White

6 - Front Left (-)---White/Black

Ignition/Red

Rear Left (+)---Green

Ground/Black

Rear Left (-)---Green/Black

1. If your car is equipped with the ISO connector, then connect the ISO connectors as illustrated.

2. For connections without the ISO connectors, check the wiring in the vehicle carefully before connecting, incorrect connection may cause serious damage to this unit.

Cut the connector, connect the colored leads of the power cord to the car battery as shown in the table below for speaker and power cable connections.

Power antenna wire is intended for power supply of the antenna and for remote control of an additional amplifier.

Control elements

Front panel

1. PWR/MOD button

2. DISP button

3. button

4. SEL/ENT/VOL

regulator

5. LCD display

6. SD card slot

7. USB port

8. AUX IN jack

9. 6 DIR+ button

10. 5 DIR- button

11. 4 RDM button

12. 3 RPT button

13. 2 INT button

14. 1 PLAY/PAUSE button

15. RESET button (hole)

16. button

17. AS/PS button

18. BAND button

General operations

Turning the unit on/off

Press the PWR button to turn the unit on. Press and hold the button again to turn the unit off.

Reset the unit

When first using the device or after replacing the car battery, you must reset the unit. Press the RESET

button (hole) with a pointed object (such as a ballpoint pen) to set the unit to its initial state.

When some errors occur, you can also press the RESET button to return to factory settings, but note that

it will erase clock setting and some memorized functions.

Mode selection

Press the PWR/MOD button repeatedly to select between Radio, AUX, USB or Memory Card modes. Operation modes are indicated on the display. Memory card and USB modes are not available unless a memory card or a USB device is connected.

Volume control

Adjust the volume by rotating the VOLUME knob.

Audio parameter setting

Press and hold the SEL/ENT/VOL knob repeatedly to select a parameter: BAS (bass) => TRE (treble) => BAL (balance) => FAD (fader) => LOUD ON/OFF => EQ (equalizer) => DX(distance)/LOC(local) => STEREO => VOL(volume). Rotate SEL/ENT/VOL knob to adjust each mode.

• Bass/Treble: from -7 to +7;

• Balance: -10 (left) to +10 (right);

• Fader: from -10 (rear) to +10 (front).

+ 21 hidden pages