Soundmax SM-CCR3035 User Manual [ru]

SM-CCR3035

USB/SD/MMC media player USB/SD/MMC-медиаплеер Instruction manual Руководство по эксплуатации

Dear customer!

Thank you for purchasing our product. For safety, it is strongly recommended to read this manual carefully before connecting, operating and/or adjusting the product and keep the manual for reference in the future.

Table of contents

TABLE OF CONTENTS .......................... ............................................................................................................................ 2

IMPORTANT SAFEGUARDS ............................................................................................................................................ 3

ACCESSORIES .......................... .......................................................................................................................................... 4

INSTALLATION/CONNECTION ............... ....................................................................................................................... 5

CONTROL ELEMENTS ....................................................................................................................................................... 9

LCD LAYOUT ....................................................................................................................................................................... 10

GENERAL OPERATIONS .................................................................................................................................................. 11

RADIO OPERATIONS ........................................................................................................................................................ 13

USB/SD/MMC OPERATIONS ................... ....................................................................................................................... 14

TROUBLESHOOTING GUIDE .......................................................................................................................................... 16

SPECIFICATION ................................................................................................................................................. ................ 17

Important safeguards

 Carefully read through this manual to familiarize yourself with this high-quality sound system.  The moment of unit installation is considered the start of its operation. When using the device in winter it

is recommended to heat the car interior for 20 minutes or up to operating temperatures.

 Use the unit with the temperature that goes beyond the operation temperature greatly decreases the

operation resource of the screen and other components of device and can result an outage.

 Disconnect the vehicle's negative battery terminal while mounting and connecting the unit.  When replacing the fuse, be sure to use one with an identical amperage rating. Using a fuse with a higher

amperage rating may cause serious damage to the unit.

 Make sure that pins or other foreign objects do not get inside the unit; they may cause malfunctions, or

create safety hazards such as electrical shock.

 Do not use the unit in places where it can be exposed to water, moisture and dust.  Do not open covers and do not repair yourself. Consult the dealer or an experienced technician for help.  Make sure you disconnect the power supply and aerial if you will not be using the system for a long period

or during a thunderstorm.

 Make sure you disconnect the power supply if the system appears to be working incorrectly, is making an

unusual sound, has a strange smell, has smoke emitting from it or liquids have got inside it. Have a qualified technician check the system.

 The unit is designed for negative terminal of the battery, which is connected to the vehicle metal. Please

confirm it before installation.

 Do not allow the speaker wires to be shorted together when the unit is switched on. Otherwise it may

overload or burn out the power amplifier.

Accessories

1. Receiver 1 pc

2. Mounting parts: Hexagon nut 1 pc Mounting sleeve 1 pc Release keys 2 pcs Metal bar 1 pc Plain washer 1 pc Spring washer 1 pc Self-tapping screw 1 pc Screw 4 pc

3. ISO-connector 1 pc

4. Consumer information 1 pc

5. Warranty card 1 pc

6. Instruction manual 1 pc

Installation/Connection

General notes

 Choose the mounting location where the unit will not interfere with the normal driving function of the

driver.

 Before finally installing the unit, connect the wiring and make sure that the unit works properly.  Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the

vehicle.

 Install the unit where it does not get in the driver's way and cannot injure the passenger if there is a

sudden stop, like an emergency stop.

 Avoid installing the unit where it would be subject to high temperature, such as from direct sunlight, or

from hot air, from the heater, or where it would be subject to dust, dirt or excessive vibration.

DIN FRONT-MOUNT

1. Car dashboard

2. Sleeve

3. Bolt

4. Nut

5. Spring washer

6. Screw

7. Metal strap

8. Flat washer

1. Install the sleeve into the dashboard; ensure it is installed with the correct side and there are no obstacles (wires, dashboard elements, etc) for the unit installation.

2. After installing the sleeve into the dashboard, bend tabs fitting to the size of the dashboard to fix the sleeve in place.

3. Use the metal strap to fix the rear side of the unit. Determine a place for fixing and install the strap as shown in the picture. You can bend the strap to the needed angle with your hands.

4. Make the necessary wire connections. Ensure the connections are correct.

5. Install the unit into the sleeve until the side locks are fixed.

Dismantling the unit

1. Make sure the ignition is turned off, then disconnect the cable from the

vehicle battery’s negative (-) terminal.

2. Remove the metal strap attached the back of the unit (if attached).

3. Insert both of the supplied keys into the slots at the middle left and right

sides of the unit, then pull the unit out of the dashboard.

Connection diagram

Notes:

 In spite of having any kinds of speaker system, must use 4 ohms impedance of speaker to reduce the

distortion during high volume level.

 It is prohibited making the conductors of auto antenna and ground touch with each other.

Using the ISO Connector

1. If your car is equipped with the ISO connector, then connect the ISO connectors as illustrated.

2. For connections without the ISO connectors, check the wiring in the vehicle carefully before connecting, incorrect connection may cause serious damage to this unit.

Cut the connector, connect the colored leads of the power cord to the car battery as shown in the table below for speaker and power cable connections.

Location Function

Connector A Connector B 1 - Rear Right (+)---Violet 2 - Rear Right (-)---Violet/Black 3 - Front Right (+)---Grey 4 Battery 12V (+)/Yellow Front Right (-)---Grey/Black 5 Auto Antenna/Blue Front Left (+)---White 6 - Front Left (-)---White/Black 7 Ignition/Red Rear Left (+)---Green 8 Ground/Black Rear Left (-)---Green/Black

Power antenna wire is intended for power supply of the antenna and for remote control of an additional amplifier.

Control elements

Front panel

1. 8/PREVIOUS button

2. MUT button

3. SELECT button/ VOLUME regulator

4. MOD/POW button

5. 9/NEXT button

6. Display

7. USB port

8. Reset button (hole)

9. LOC button

10. BND/7/LOU button

11. AS/PS button

12. 1/PAU button

13. 2/INT button

14. 3/RPT button

15. 4/RDM button

16. 5/DIR- button

17. 6/DIR+ button

18. DSP/0 button

19. AUX input

20. Memory card slot

LCD layout

1. POP equalizer mode

2. CLASSIC equalizer mode

3. ROCK equalizer mode 4, 5. Audio format indicators

6. Local station indicator

7. Loudness indicator

8. Intro playback indicator

9. Repeat playback indicator

10. Random playback indicator

11. USB connect indicator

12. SD card insert indicator

13. Digit display (radio frequency, track name/number, etc.)

14. Stereo reception indicator

The picture of LCD layout is for reference only and may differ from the real-life layout.

General operations

Power button

Press MOD/PWR button on the panel to switch the unit on. Press and hold this button to switch the unit off.

Volume control

Rotate VOLUME regulator to adjust volume level.

Sound muting

Press MUT button to switch the sound off. Press this button again or rotate VOLUME regulator to enable the sound.

Audio settings adjustment

Press SELECT button shortly and repeatedly to select an option: BAS (bass) => TRE (treble) => BAL (balance) => FAD (fader). Rotate VOLUME regulator to adjust bass, treble, balance or fader.

Note: When equalizer is on, bass and treble adjustment is not available. Caution: In each mode, the waiting time is several seconds, and when the waiting time is over, it returns to

the last display mode of radio or playback mode.

Mode selection

Press MOD/POW button to choose a sound source: RADIO => USB => Memory card => AUX. USB and memory card modes are available only when the storage is connected to this unit.

Clock adjustment

Press and hold DSP/0 button to go to clock adjustment mode. Hour digits will blink. Rotate VOLUME regulator to adjust hours. Press SELECT button to go to minute adjustment; minute digits will blink. Rotate VOLUME regulator to adjust minutes. Press DSP/0 button to confirm clock setting. In any mode press shortly DSP/0 button to display the clock.

Equalizer setting

Press SELECT button shortly and repeatedly until EQ OFF (POP/CLASS/ROCK) is displayed. Rotate VOLUME regulator to choose between sound effects: POP => CLASSIC => ROCK => EQ OFF.

+ 23 hidden pages