Remote Sense
The maximum load line drop is up to the full voltage rating
of the supply. The drop in the load leads subtracts from the
maximum voltage available for the load except as follows:
maximum rated voltage is available at the load and voltage
regulation specifications apply for line drops of<1V on
DLM5-75 and DLM8-75, <2V for all other DLM600 models
and DLM3K/4K models rated 5V to 16V, and <5V for all
other DLM3K/4K models.
Remote
Programming
Remote
Monitoring
Operational
Features
Software
Regulatory
Compliance
Input
Voltage and
Frequency
Current
Connector
Voltage, current (0-100%) and OVP (5-110%) of full scale
can be programmed by selectable 0
5kÙ
Voltage or current can be monitored with userselectable
ranges, scaled to 0-5 VDC or 0-10 VDC
Master/slave parallel operation, up to 4 units of the same
model can be connected in parallel, with active current
sharing control. Series operation, multiple units of the
same model can be connected in series, limited by 300Vpk
between either output terminal and chassis.
IVI-COM, LabVIEW® or LabWindow
Ethernet and IEEE-488.2
CE Compliant:
Low Voltage Directive (73/23/EEC) using EN 61010
and
EMC Directive (89/336/EEC) using EN 61326 Certified to
UL 61010-1, CSA C22.2 No. 61010.1 and IEC/EN 61010
90-132 VAC or 180-264 VAC max, auto ranging,
47-63 Hz, single phase, 2-wire plus ground
11A maximum at 115VAC, 6A maximum at 230 VAC
IEC 320 with detachable line cord
-
5VDC, 0-10VDC, or 0
® /
CVI driver for
-
1,
-
-1
Power Factor
Output
Line Regulation
Load Regulation
Transient
Response
Stability
Efficiency
Temperature
Coefficient
0.6, typical at full load; dependent on the impedance of
the AC input.
Voltage: 0.005% of V max + 2 mV
Current: 0.01% of I max + 2 mA
See table for input voltage variation over the AC input
voltage range, with constant rated load.
Voltage: 0.005% of V max + 2 mV
Current: 0.02% of I max + 5 mA
See table For 0-100% load variation, with constant
nominal line voltage
500 ìs to steady-state output voltage (within 0.1% of
Vmax) for 50-100% or 100-50% load change
±
0.05% of maximum voltage or current over 8 hours
after 30 minute warm-up time at fixed line, load and
temperature
84% typical at maximum output power; 82% typical for
DLM 5-75 and DLM 8-75
0.02%/°C of maximum output voltage, 0.03%/°C of
maximum output current. Change in output per °C
change in ambient temperature, with constant line and
load.
Physical
Dimensions
Width:
8.5
(
216 mm)
Height:
1U or 1.75
Depth:
17
Weight & Shipping Weight
Weight
Shipping Weight
Output Ratings
9.7 lbs. (4.4 kg)
12.7 lbs. (5.8 kg)
(
44 mm)
(
432 mm) Option M6 depth 20
(
508 mm)
Programming Accuracy
Ripple and Noise
Analog User I/O Pinouts
10
11
12
13
1
2
3
4
5
6
7
8
9
ANALOG-CONTROL Input
EXTERNAL-OFF Return
OVP Programming Input
REMOTE-CONTROL Status Output
VOLTAGE-MODE Status Output
Auxiliary 5 VDC Return
Current Monitor Output
Voltage/Current Monitor Return
Voltage Programming Input
Current Programming Input
Not Used
V/I/OVP Programming Return
Not Used
14
15
16
17
18
19
20
21
22
23
24
25
EXTERNAL-OFF Input (+)
Auxiliary 5 VDC Output (+)
OVP Resistance Programming Output
OVP Resistance Programming Return
FAULT Status Output
Voltage Monitor Output
Voltage Resistance Programming
Return
Voltage Resistance Programming
Output
Current Resistance Programming
Output
Current Resistance Programming
Return
LOCAL-LOCKOUT Input
OVP Status Output
Loading...