Sony XDCA-55 User Manual

Page 1
4-260-664-11 (1)
HD Camera Adaptor
Operating Instructions
Before operating the unit, please read this manual thoroughly and retain it for future reference.
XDCA-55
© 2010 Sony Corporation
4260664110
Page 2
WARNING
To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.
This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
Important Safety Instructions
• Read these instructions.
• Keep these instructions.
• Heed all warnings.
• Follow all instructions.
• Do not use this apparatus near water.
• Clean only with dry cloth.
• Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
• Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
• Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
• Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
• Only use attachments/accessories specified by the manufacturer.
• Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
• Unplug this apparatus during lightning storms or when unused for long periods of time.
• Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
IMPORTANT
The nameplate is located on the bottom.
WARNING
Excessive sound pressure from a headset can cause hearing loss. In order to use this product safely, avoid prolonged listening at excessive sound pressure levels.
The total power consumption including this adaptor’s power consumption, DC power output, and power supply to the camcorder must not exceed 70 W.
For the customers in the U.S.A.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
Page 3
installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.
The manufacturer of this product is Sony Corporation, 1-7-1 Konan, Minato-ku, Tokyo, Japan. The Authorized Representative for EMC and product safety is Sony Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Germany. For any service or guarantee matters please refer to the addresses given in separate service or guarantee documents.
All interface cables used to connect peripherals must be shielded in order to comply with the limits for a digital device pursuant to Subpart B of Part 15 of FCC Rules.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
For the customers in Canada
This Class A digital apparatus complies with Canadian ICES-003.
For the customers in Europe
This product with the CE marking complies with the EMC Directive issued by the Commission of the European Community. Compliance with this directive implies conformity to the following European standards:
• EN55103-1: Electromagnetic Interference (Emission)
• EN55103-2: Electromagnetic Susceptibility (Immunity)
This product is intended for use in the following Electromagnetic Environments: E1 (residential), E2 (commercial and light industrial), E3 (urban outdoors), E4 (controlled EMC environment, ex. TV studio).
AVERTISSEMENT
Afin de réduire les risques d’incendie ou d’électrocution, ne pas exposer cet appareil à la pluie ou à l’humidité.
Afin d’écarter tout risque d’électrocution, garder le coffret fermé. Ne confier l’entretien de l’appareil qu’à un personnel qualifié.
IMPORTANT
La plaque signalétique se situe sous l’appareil.
AVERTISSEMENT
Une pression acoustique excessive en provenance du casque peut provoquer une baisse de l’acuité auditive. Pour utiliser ce produit en toute sécurité, évitez l’écoute prolongée à des pressions sonores excessives.
Pour les clients au Canada
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
Pour les clients en Europe
Ce produit portant la marque CE est conforme à la Directive sur la compatibilité électromagnétique (EMC) émise par la Commission de la Communauté européenne.
Page 4
La conformité à cette directive implique la conformité aux normes européennes suivantes :
• EN55103-1 : Interférences électromagnétiques (émission)
• EN55103-2 : Sensibilité électromagnétique (immunité)
Ce produit est prévu pour être utilisé dans les environnements électromagnétiques suivants : E1 (résidentiel), E2 (commercial et industrie légère), E3 (urbain extérieur) et E4 (environnement EMC contrôlé, ex. studio de télévision).
Le fabricant de ce produit est Sony Corporation, 1-7-1 Konan, Minato-ku, Tokyo, Japon. Le représentant autorisé pour EMC et la sécurité des produits est Sony Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Allemagne. Pour toute question concernant le service ou la garantie, veuillez consulter les adresses indiquées dans les documents de service ou de garantie séparés.
WARNUNG
Um die Gefahr von Bränden oder elektrischen Schlägen zu verringern, darf dieses Gerät nicht Regen oder Feuchtigkeit ausgesetzt werden.
WARNUNG
Zu hoher Schalldruck von Headset kann Gehörschäden verursachen. Um dieses Produkt sicher zu verwenden, vermeiden Sie längeres Hören bei sehr hohen Schalldruckpegeln.
Für Kunden in Europa
Dieses Produkt besitzt die CE­Kennzeichnung und erfüllt die EMV­Richtlinie der EG-Kommission. Angewandte Normen:
• EN55103-1: Elektromagnetische Verträglichkeit (Störaussendung)
• EN55103-2: Elektromagnetische Verträglichkeit (Störfestigkeit)
Für die folgenden elektromagnetischen Umgebungen: E1 (Wohnbereich), E2 (kommerzieller und in beschränktem Maße industrieller Bereich), E3 (Stadtbereich im Freien) und E4 (kontrollierter EMV­Bereich, z.B. Fernsehstudio).
Der Hersteller dieses Produkts ist Sony Corporation, 1-7-1 Konan, Minato-ku, Tokyo, Japan. Der autorisierte Repräsentant für EMV und Produktsicherheit ist Sony Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Deutschland. Bei jeglichen Angelegenheiten in Bezug auf Kundendienst oder Garantie wenden Sie sich bitte an die in den separaten Kundendienst- oder Garantiedokumenten aufgeführten Anschriften.
Um einen elektrischen Schlag zu vermeiden, darf das Gehäuse nicht geöffnet werden. Überlassen Sie Wartungsarbeiten stets nur qualifiziertem Fachpersonal.
WICHTIG
Das Namensschild befindet sich auf der Unterseite des Gerätes.
Page 5

Table of Contents

Overview ..................................................................................6
Features ...................................................................................6
Using the CD-ROM ................................................................7
Reading the CD-ROM Manuals ..........................................7
Names and Functions of Parts............................................... 8
System Configuration........................................................... 12
Attaching the Adaptor to a Camcorder .............................12
Important Notes on Operation ............................................14
Specifications .........................................................................14
General ..............................................................................14
Connectors ........................................................................15
Supplied Accessories ........................................................15
Accessories Not Supplied .................................................15
Table of Contents
Page 6

Overview

Features

The XDCA-55 HD Camera Adaptor (referred to as “the adaptor” hereafter) allows you to connect an XDCU-50 HD Camera Extension Unit to supply power to the camcorder and extend the distance over which camcorder input and output signals can be transmitted (maximum distance 100 m (328 feet)).
Can be installed on the following camcorders
• PMW-350K/350L
• PMW-320K/320L
•PMW-500
1) An optional CBK-CE01 50 Pin Interface and Digital Extender is required.
2) An optional CBK-HD02 SDI/COMPOSITE Input and 50 Pin Interface is required.
For details, refer to the XDCU-50 Operating Instructions for information about how to set up a system consisting of this adaptor, a camcorder, and the XDCU-50, and for precautions about use of the system.
1)
1)
2)
HD digital transmission
This adaptor supports bidirectional transmission of uncompressed HD digital signals between this adaptor and XDCU-50. The maximum transmission distance is 100 m (328 feet). You can transmit high-quality video signals regardless of cable length.
Cable-free connection via 50-pin interface
You can easily make a cable-free connection by connecting the camcorder connector of this adaptor directly to the camera adaptor connector of the camcorder (requires installation of optional interface).
Monitor output connector
Either main line video signals from the camcorder or return video signals from the XDCU-50 can be output as HDSDI signals.
Return video selection button
You can switch the monitor output to return video while the adaptor’s RET button is held down.
Communication interfaces
• Intercom (1 line)
• Tally (red and green)
• Trunk line (1 line)
Overview / Features
Page 7

Using the CD-ROM

The supplied CD-ROM contains PDF­format Operating Instructions manuals (in English, Japanese, French, German, Italian, Spanish, and Chinese) for this adaptor, a HD Camera Adaptor XDCA-53 and a HD Camera Extension Unit XDCU-50.

Reading the CD-ROM Manuals

Preparations
The following program must be installed on your computer in order to read the documents contained on the CD-ROM. Adobe Reader Version 6.0 or higher
Memo
If Adobe Reader is not installed, you can download it from the following URL: http://www.adobe.com/
Adobe and Adobe Reader are trademarks of Adobe Systems Incorporated in the United States and/or other countries.
This opens the PDF file.
Memo
The files may not be displayed properly, depending on the version of Adobe Reader. In such a case, install the latest version you can download from the URL mentioned in “Preparations” above.
Note
If you have lost or damaged the CD-ROM, you can purchase a new one to replace it. Contact a Sony service representative.
To read the documents
Do the following:
1 Insert the CD-ROM in your CD-ROM
drive.
A cover page appears automatically in your browser. If it does not appear automatically in the browser, double-click on the index.htm file on the CD-ROM.
2 Select and click on the manual that you
wish to read.
Using the CD-ROM
Page 8

Names and Functions of Parts

qhINTERCOM LEVEL knob
qgCEU connector
qfAUX connector
qdINTERCOM connector
qsDC OUT 12V 1A
connector
qaMONITOR OUT(SDI) connector
wdAccessory screw holes
(for HD viewfinder)
1INTERCOM MIC switch
2TALLY lamp (green)
3TALLY lamp (red)
4TALLY switch
5Belt bracket screw holes
6CALL button
7RET button
8MONI. SEL switch
9CEU OUT connector
0CEU IN connector
qjCamcorder screws
wsAccessory screw holes
(for general use)
waCamcorder bracket attachment
screw hole
w;V shoe
qlCamcorder power supply connector
Names and Functions of Parts
qkCamcorder connector
Page 9
a INTERCOM MIC switch
Controls the headset microphone connected to the INTERCOM connector, turning it on or off as required.
ON: Turns the headset microphone on. OFF: Turns the headset microphone off. PTT: Turns the headset microphone on for
as long as the switch is held in this position.
b TALLY lamp (green)
When the TALLY switch is on, lights in green when a green tally signal is input to an XDCU-50 connected to the adaptor.
c TALLY lamp (red)
When the TALLY switch is on, lights in red when a red tally signal is input to an XDCU-50 connected to the adaptor, and when a call signal is received, for example because a CALL button was pressed on another device.
When this button is pressed, the TALLY or CALL lamps on the camcorder, the XDCU­50, and the remote control unit light. On the other hand, the TALLY lamp on this adaptor does not light.
Note
Control over tally lamps varies depending on the devices used in the system (camcorder, XDCU-50, remote control unit).
For details, refer to the instruction manuals of the other devices.
g RET (return) button
Switches the video in the viewfinder to return video. When the MONI. SEL switch is set to CAM/RET, you can also switch the output signal from the MONITOR OUT(SDI) connector to return video.
Note
This lamp does not light when the adaptor’s CALL button is pressed.
d TALLY switch
Enables (on) or disables (off) the TALLY lamps (red and green). However, tally signals assigned to pins 14 and 15 of the AUX connector are not affected by the setting of this switch. ON: Lights the TALLY lamps (red and
green) according to tally signals and the state of the CALL button.
OFF: Does not light the TALLY lamps (red
and green).
e Belt bracket screw holes
These are screw holes (2) for M3 screws to secure a belt bracket.
f CALL button
Calls the operator of a XDCU-50 or remote control unit.
h MONI. SEL (monitor select) switch
Selects the output from the MONITOR OUT(SDI) connector.
RET: Always outputs return video signals. CAM/RET: Outputs return video as long
as the RET button is pressed, and outputs camcorder video signal when the RET button is not pressed.
i CEU OUT (camera extension unit
output) connector
Connect to the CA IN connector of the XDCU-50 with a BNC cable (5C-FB).
j CEU IN (camera extension unit
input) connector
Connect to the CA OUT connector of the XDCU-50 with a BNC cable (5C-FB).
k MONITOR OUT(SDI) connector
Outputs HD SDI signals, either return video signals from the XDCU-50 video signals from the camcorder.
Names and Functions of Parts
Page 10
l DC OUT 12V 1A connector (XLR 4-
pin)
Supplies +12 V power to a monitor or other external device. The pin assignments are as follows.
Provides a trunk line connection to the trunk line of the camera adaptor via a RS­232C interface, for use as a communications line with external devices. Also equipped with general-purpose lines between this camcorder and the XDCU-50. The pin assignments are as follows.
Pin No. Signal name
1GND
2 Not used
3 Not used
4+12V
m INTERCOM connector (XLR 5-pin)
Allows you to connect an XLR 5-pin type headset. The pin assignments are as follows.
Pin No. Signal name
1 INCOM MIC GND
2 INCOM MIC IN
3 INCOM RECEIVE GND
4 INCOM RECEIVE OUT
5 Not used
Contact your dealer or a Sony servic e representative for information about how to adjust the side tone level.
n AUX connector (15-pin)
Connect to an external system to input and output tally signals, trunk line signals, and timecode.
Pin
Signal name Description
No.
2 TC (X) OUT Timecode signal
7 TC (G) OUT
3 TRUNK RX Trunk line (RS-
13 TRUNK TX
8 TRUNK (G)
4 RET CONT IN Return control
9 MIC CONT IN Intercom
5 GND Ground
10 TALLY GND TALLY output
14 R TALLY OUT Red tally output
15 G TALLY OUT Green tally
1 AUX VIDEO (X) General-
6 AUX VIDEO (G)
output
232C)
external input
On: GND Off: Open
microphone control input
On: GND Off: Open
(open collector)
output (open collector)
purpose analog video line between this adaptor and XDCU-50
Names and Functions of Parts
10
Page 11
Pin
Signal name Description
No.
11 AUX1 General-
12 AUX2 General-
purpose line 1 between this adaptor and XDCU-50
purpose line 2 between this adaptor and XDCU-50
o CEU (camera extension unit)
connector (26-pin)
Connect to the CA connector (26-pin) of the XDCU-50 with the optional CCZ-A cable. Power is supplied from the XDCU-50.
For details on the pin assignments, refer to the description on the CA OUT connector in the Operating Instructions for the XDCU-50.
p INTERCOM LEVEL knob
Adjusts the receiving volume level of the headset connected to the INTERCOM connector.
u Camcorder bracket attachment
screw hole
This is a screw hole for a bracket to increase the security of the attachment of this adaptor to the camcorder.
v Accessory screw holes (for general
use)
These are a screw hole for an U1/4-20 screw to secure an accessory, and eight screw holes to secure the accessory fitting shoe (for the DXF-C50W viewfinder).
w Accessory screw holes (for HD
viewfinder)
These are accessory screw holes (4) for M4 screws to secure an HD monitor.
q Camcorder screws
Screws to secure the adaptor to the camcorder.
r Camcorder connector (50-pin)
Connect to the camera adaptor connector of the camcorder (requires installation of an optional interface) to send and receive video and audio signals.
s Camcorder power supply connector
Supplies power to the camcorder.
t V shoe
This is a V shoe for attachment of this adaptor to the camcorder.
Names and Functions of Parts
11
Page 12

System Configuration

The following figure shows the configuration of a system that includes the adaptor.
Camcorder (with optional CBK­CE01/HD02 installed in the camera adaptor connector)
This adaptor
Note
Do not connect or disconnect the cables connecting this adaptor and XDCU-50 (CCZ-A and BNC cables) while the system is powered on. The excessive current protection function may be activated, cutting off power to the power circuits of this adaptor or the XDCU-50. If the power should be cut off, connect the cables again in the proper fashion and wait for a while before starting the system again.
Refer to the XDCU-50 Operating Instructions for details about how to use the adaptor when it is connected to the XDCU-50.
XDCU-50
a) CCZ-A cable b) BNC cable

Attaching the Adaptor to a Camcorder

1 Screw two of the brackets supplied
with this adaptor to the battery attachment shoe of the camcorder.
System Configuration
12
Brackets (supplied)
2 Attach the adaptor to the battery
attachment shoe of the camcorder.
3 Tighten the attachment screws at the
top of the adaptor.
Page 13
Attachment screws
4 Screw the remaining two of the
brackets supplied with this adaptor to the brackets fixed in step 1 and the side panel of this adaptor.
5 Attach the supplied brackets with
screws.
Note
Tighten the screws securely so that the unit will not fall off.
To remove
Perform the installation procedure in reverse, loosening the screws that were tightened then.
Brackets (supplied)
The release button on the camcorder will not function.
System Configuration
13
Page 14

Important Notes on Operation

Use and storage locations
Store in a level, ventilated place. Avoid using or storing the adaptor in the following places.
• In excessive heat or cold (operating
temperature range: –5°C to +40°C (–23°F to +104°F))
• Remember that in summer in warm
climates the temperature inside a car with the windows closed can easily exceed 50°C (122°F).
• In damp or dusty locations
• Locations where the adaptor may be
exposed to rain
• Locations subject to violent vibration
• Near strong magnetic fields
• Close to radio or TV transmitters
producing strong electromagnetic fields.
• In direct sunlight or close to heaters for
extended periods
Do not subject to strong shocks
Do not drop the adaptor or subject it to strong shocks. The adaptor may be damaged.

Specifications

General

Power requirements
13 V DC
Power consumption
Approx. 4 W
Notes
• Connect only a device with a power consumption current of 1A or less to the DC OUT connector.
• The total power consumption including this adaptor’s power consumption, DC power output, and power supply to the camcorder must not exceed 70 W.
Operating temperature
–5°C to +40°C (–23ºF to +104ºF)
Operating humidity
20% to 90%
Storage temperature
–20°C to +60°C (–4ºF to +40ºF)
Dimensions
Do not wrap in a cloth or other covering during operation
Internal temperatures may rise, causing malfunctions.
Maintenance
Clean the cabinet and panels by wiping lightly with a soft, dry cloth. If they are very dirty, use a cloth dampened with a small amount of neutral detergent, then wipe dry. Avoid the use of volatile solvents such as thinners, alcohol, benzene, and insecticides. They may damage the surface finish or cause it to peel off.
Important Notes on Operation / Specifications
14
(unit: mm (inches))
Mass Approx. 1.0 kg (2 lb 3.3 oz)
Page 15

Connectors

Camera extension input/output connectors
CEU IN/OUT
BNC type (1 each), 0.8 Vp-p, 75Ω
CEU(26Pin)
CCZ 26-pin, female
Camcorder input/output connectors
Camcorder connector
50-pin, female
Output connectors
MONITOR OUT(SDI)
BNC type, 0.8 Vp-p, 75Ω
Other connectors
INTERCOM
XLR 5-pin, female AUX D-Sub 15-pin, female Camcorder power supply
5-pin, female DC OUT 12V 1A
XLR 4-pin, female
DC 12 V, maximum rated current
1A
Design and specifications are subject to change without notice.
Note
Always verify that the unit is operating properly before use. SONY WILL NOT BE LIABLE FOR DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED TO, COMPENSATION OR REIMBURSEMENT ON ACCOUNT OF THE LOSS OF PRESENT OR PROSPECTIVE PROFITS DUE TO FAILURE OF THIS UNIT, EITHER DURING THE WARRANTY PERIOD OR AFTER EXPIRATION OF THE WARRANTY, OR FOR ANY OTHER REASON WHATSOEVER.

Supplied Accessories

Operating Instructions
Japanese (1)
English (1) CD-ROM (1) Brackets (4) Bracket fixing screws (10) Belt bracket (1) Belt bracket fixing screws (2) Cable clamp belt (1)

Accessories Not Supplied

Accessory shoe kit (A-8274-966-B)
Specifications
15
Page 16
Printed in China
Loading...