Sony XAV-70BT User Manual [es, it, en]

4-164-314-23 (1)

AV Center

XAV-70BT

Operating Instructions

Manual de instrucciones

Istruzioni per l’uso

Be sure to install this unit in the dashboard of the car for safety. For installation and connections, see the supplied installation/ connections manual.

Warning

To prevent fire or shock hazard, do not expose the unit to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.

CAUTION

The use of optical instruments with this product will increase eye hazard. As the laser beam used in this CD/DVD player is harmful to eyes, do not attempt to disassemble the cabinet. Refer servicing to qualified personnel only.

This label is located on the bottom of the chassis.

The nameplate indicating operating voltage, etc., is located on the bottom of the chassis.

Hereby, Sony Corp., declares that this XAV70BT is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. For details, please access the following URL: http://www.compliance.sony.de/

Use of this radio equipment is not allowed in the geographical area within a radius of 20 km from the centre of Ny-Alesund, Svalbard in Norway.

Notice for customers: the following information is only applicable to equipment sold in countries applying EU Directives

The manufacturer of this product is Sony Corporation, 1-7-1 Konan, Minato-ku Tokyo, 108-0075 Japan. The Authorized Representative for EMC and product safety is Sony Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Germany. For any service or guarantee matters please refer to the addresses given in separate service or guarantee documents.

Disposal of Old Electrical & Electronic Equipment (Applicable in the European Union and other European countries with separate collection systems)

This symbol on the product or on its packaging indicates that this product shall not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. The recycling of materials will help to conserve natural resources. For more detailed information about recycling of this product, please contact your local Civic Office, your household waste disposal service or the shop where you purchased the product.

Applicable accessories: Remote commander, Microphone

Disposal of waste batteries

(applicable in the European Union

and other European countries with

separate collection systems)

This symbol on the battery or on the packaging indicates that the battery provided with this product shall not be treated as household waste. On certain batteries this symbol might be used in combination with a chemical symbol. The chemical symbols for mercury (Hg) or lead (Pb) are added if the battery contains more than 0.0005% mercury or 0.004% lead. By ensuring these batteries are disposed of correctly, you will help prevent potentially negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of the battery. The recycling of the materials will help to conserve natural resources. In case of products that for safety, performance or data integrity reasons require a permanent connection with an incorporated battery, this battery should be replaced by qualified service staff only. To ensure that the battery will be treated properly, hand over the product at end-of-life to the applicable collection point for the recycling of electrical and electronic equipment. For all other batteries, please view the section on how to remove the battery from the product safely. Hand the battery over to the applicable collection point for the recycling of waste batteries. For more detailed information about recycling of this product or battery, please contact your local Civic Office, your household waste disposal service or the shop where you purchased the product.

Warning if your car’s ignition has no ACC position

Be sure to set the Auto Off function (page 54). The unit will shut off completely and automatically in the set time after the unit is turned off, which prevents battery drain. If you do not set the Auto Off function, press and hold (SOURCE/OFF) until the display disappears each time you turn the ignition off.

To cancel the demonstration (Demo) display, see page 57.

Note on the lithium battery

Do not expose the battery to excessive heat such as direct sunlight, fire or the like.

Table of Contents

Notes on safety . . . . . . . . . . . . . . . . . . . . . . . . . 8

Notes on installation . . . . . . . . . . . . . . . . . . . . . 8

Copyrights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Notes on Bluetooth . . . . . . . . . . . . . . . . . . . . . 10

Playable discs and symbols used in this

manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Location and function of controls . . . . . . . . . . 12

Main unit. . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Card remote commander RM-X170. . . . . . 14

Getting Started

Resetting the unit. . . . . . . . . . . . . . . . . . 16

Performing initial settings. . . . . . . . . . . 16

Preparing the card remote

commander. . . . . . . . . . . . . . . . . . . . . . . 16

Basic Operations

Listening to the radio . . . . . . . . . . . . . . 17

Playing discs . . . . . . . . . . . . . . . . . . . . . 19

Advanced Operations — Radio

Storing and receiving stations . . . . . . . . . . . . . 23

Storing automatically — BTM . . . . . . . . . . 23

Storing manually. . . . . . . . . . . . . . . . . . . . . 23

Receiving stored stations . . . . . . . . . . . . . . 23

RDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Setting AF and TA . . . . . . . . . . . . . . . . . . . 24

Selecting PTY. . . . . . . . . . . . . . . . . . . . . . . 24

Setting CT. . . . . . . . . . . . . . . . . . . . . . . . . . 24

Advanced Operations — Discs

Using PBC functions — Playback control . . . 25

Configuring audio settings . . . . . . . . . . . . . . . 25

Changing the audio language/format . . . . . 25

Changing the audio channel. . . . . . . . . . . . 26

Adjusting the audio output level

— Dolby D level . . . . . . . . . . . . . . . . . . . . 26

Locking discs — Parental control. . . . . . . . . . 26

Activating parental control. . . . . . . . . . . . . 26

Changing the area and its movie rating

level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Repeat and shuffle play. . . . . . . . . . . . . . . . . . 27

Direct search play . . . . . . . . . . . . . . . . . . . . . . 28

USB Device Operations

Playing a USB device . . . . . . . . . . . . . . . . . . . 29

Repeat and shuffle play. . . . . . . . . . . . . . . . . . 29

Enjoying music according to your mood

— SensMe™. . . . . . . . . . . . . . . . . . . . . . . . . . 30

Before using the SensMe™ function . . . . . 30

Installing “SensMe™ Setup” and “Content

Transfer” in your computer . . . . . . . . . . . . 30

Registering a USB device using “SensMe™

Setup”. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Transferring tracks to the USB device using

“Content Transfer”. . . . . . . . . . . . . . . . . . . 31

Playing tracks in the channel

— SensMe™ channels. . . . . . . . . . . . . . . . 31

Playing tracks in the mood map

— SensMe™ mood . . . . . . . . . . . . . . . . . . 33

iPod Operations

Playing an iPod. . . . . . . . . . . . . . . . . . . . . . . . 34

Setting the play mode . . . . . . . . . . . . . . . . . . . 34

Repeat and shuffle play. . . . . . . . . . . . . . . . . . 35

Operating an iPod directly

— Passenger control. . . . . . . . . . . . . . . . . . . . 35

continue to next page t

Useful Functions

Sound Adjustment

Listing up tracks/images/video files

— List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

Selecting a track/image/video file . . . . . . . .36

Selecting a file type . . . . . . . . . . . . . . . . . . .36

Searching a track by listening to track passages

— ZAPPIN™. . . . . . . . . . . . . . . . . . . . . . . . . .36

Using Gesture Command . . . . . . . . . . . . . . . . .37

Handsfree Calling and Audio Streaming — Bluetooth

Before using the Bluetooth function . . . . . . . .37

Basic procedure of the Bluetooth

function . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

Bluetooth status indication . . . . . . . . . . . . .38

Installing the external microphone

XA-MC10 . . . . . . . . . . . . . . . . . . . . . . . . . .38

Pairing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

Searching from this unit . . . . . . . . . . . . . . .38

Searching from the Bluetooth device . . . . .39

Connecting . . . . . . . . . . . . . . . . . . . . . . . . . . . .39

Handsfree calling . . . . . . . . . . . . . . . . . . . . . . .40

Making calls . . . . . . . . . . . . . . . . . . . . . . . .40

Receiving calls. . . . . . . . . . . . . . . . . . . . . . .42

Operations during a call. . . . . . . . . . . . . . . .42

Phonebook management . . . . . . . . . . . . . . . . .43

Storing phonebook data. . . . . . . . . . . . . . . .43

Browsing a phonebook in a cellular

phone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44

Deleting phonebook data. . . . . . . . . . . . . . .44

Editing a contact . . . . . . . . . . . . . . . . . . . . .44

Call data management . . . . . . . . . . . . . . . . . . .45

Call history . . . . . . . . . . . . . . . . . . . . . . . . .45

Preset dial . . . . . . . . . . . . . . . . . . . . . . . . . .45

Locking the personal information . . . . . . . .46

Audio streaming. . . . . . . . . . . . . . . . . . . . . . . .46

Listening to a Bluetooth device through

this unit . . . . . . . . . . . . . . . . . . . . . . . . . . . .46

Operating the Bluetooth device with

this unit . . . . . . . . . . . . . . . . . . . . . . . . . . . .46

Bluetooth settings. . . . . . . . . . . . . . . . . . . . . . .47

Selecting the sound quality — EQ7 . . . . . . . . 48

Customizing the equalizer curve

— EQ7 Tune. . . . . . . . . . . . . . . . . . . . . . . . 48

Adjusting the sound characteristics. . . . . . . . . 48

Optimizing sound for the listening position

— Intelligent Time Alignment . . . . . . . . . . . . 49

Precisely calibrating the listening position

— Intelligent Time Alignment Tune . . . . . 49

Speaker configuration and volume setup . . . . 50

Creating a virtual center speaker

— CSO . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Using rear speakers as subwoofer

— RBE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Adjusting the speaker volume. . . . . . . . . . . 50

Monitor Adjustment

Adjusting the monitor angle . . . . . . . . . . . . . . 51

Touch panel calibration. . . . . . . . . . . . . . . . . . 51

Setting the background screen. . . . . . . . . . . . . 51

Selecting the picture quality

— Picture EQ . . . . . . . . . . . . . . . . . . . . . . . . . 51

Customizing the picture quality . . . . . . . . . 52

Selecting the aspect ratio. . . . . . . . . . . . . . . . . 52

Settings

Basic setting operation . . . . . . . . . . . . . . . . . . 53

General settings. . . . . . . . . . . . . . . . . . . . . . . . 54

Sound settings . . . . . . . . . . . . . . . . . . . . . . . . . 56

Screen settings. . . . . . . . . . . . . . . . . . . . . . . . . 57

DVD and other playback settings . . . . . . . . . . 58

Setting the security code . . . . . . . . . . . . . . . . . 61

Setting the clock . . . . . . . . . . . . . . . . . . . . . . . 61

Using Optional Equipment

Auxiliary audio/video equipment . . . . . . . . . . 61

Rear view camera . . . . . . . . . . . . . . . . . . . . . . 62

Rear view camera settings . . . . . . . . . . . . . 62

Additional Information

Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Notes on LCD panel . . . . . . . . . . . . . . . . . . 63

Notes on discs. . . . . . . . . . . . . . . . . . . . . . . 63

Playback order of MP3/WMA/AAC/JPEG/

/MPEG-4 files . . . . . . . . . . . . . . . . . 64

DivX

About MP3 files . . . . . . . . . . . . . . . . . . . . . 64

About WMA files . . . . . . . . . . . . . . . . . . . . 64

About AAC files. . . . . . . . . . . . . . . . . . . . . 64

About JPEG files . . . . . . . . . . . . . . . . . . . . 64

About DivX video. . . . . . . . . . . . . . . . . . . . 64

About DivX Video-on-Demand . . . . . . . . . 65

About MPEG-4 files. . . . . . . . . . . . . . . . . . 65

About iPod . . . . . . . . . . . . . . . . . . . . . . . . . 65

About Bluetooth function . . . . . . . . . . . . . . 65

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Removing the unit . . . . . . . . . . . . . . . . . . . . . . 66

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . 67

Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . 68

Error displays/messages . . . . . . . . . . . . . . . 71

Language code/area code list. . . . . . . . . . . . . . 73

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

Support site

If you have any questions or for the latest support information on this product, please visit the web site below:

http://support.sony-europe.com/

Provides information on:

• Models and manufacturers of compatible digital audio players

• Models and manufacturers of compatible cellular phones and the FAQ about Bluetooth function

Notes on safety

Notes on installation

• Comply with your local traffic rules, laws and regulations.

• While driving – Do not watch or operate the unit, as it may lead

to distraction and cause an accident. Park your car in a safe place to watch or operate the unit.

– Do not use the setup feature or any other

function which could divert your attention from the road.

– When backing up your car, be sure to

look back and watch the surroundings carefully for your safety, even if the rear view camera is connected. Do not depend on the rear view camera exclusively.

• While operating – Do not insert your hands, fingers or foreign

object into the unit while functioning, as it may

cause injury or damage to the unit. – Keep small articles out of the reach of children. – Be sure to fasten seatbelts to avoid injury in the

event of a sudden movement of the car.

Preventing an accident

Pictures appear only after you park the car and set the parking brake. If the car starts moving during video playback, the picture is automatically switched to the background screen after displaying the caution below.

“Video blocked for your safety.”

The monitor connected to the REAR VIDEO OUT is active while the car is in motion. The picture on the display is switched to the background screen, but audio source can be heard.

Do not operate the unit or watch the monitor while driving.

• We recommend this unit should be installed by a qualified technician or service personnel. – If you try to install this unit by yourself, see the

supplied installation/connections manual and install the unit properly.

– Improper installation may cause battery drain or

a short circuit.

• If the unit does not work properly, check the connections first, referring to the supplied installation/connections manual. If everything is in order, check the fuse.

• Protect the unit surface from damage. – Do not expose the unit surface to chemicals,

such as insecticide, hair spray, insect repellent, etc.

– Do not leave rubber or plastic materials in

contact with the unit for a long time. Otherwise, the finish of the unit may be impaired, or deformation may occur.

• When installing, be sure to fix securely.

• When installing, be sure to turn the ignition off. Installing the unit with the ignition on may cause battery drain or a short circuit.

• When installing, be sure not to damage any car parts such as pipes, tubes, fuel tank or wiring by using a drill, as it may cause a fire or an accident.

Copyrights

This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.

Manufactured under license from Dolby Laboratories.

symbol are trademarks of Dolby Laboratories.

United States and/or other countries.

“DVD VIDEO,” “DVD-R,” “DVD-RW,” “DVD+R,” and “DVD+RW” are trademarks.

The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Sony Corporation is under license. Other trademarks and trade names are those of their respective owners.

ZAPPIN is a trademark of Sony Corporation.

“Dolby” and the double-D

Microsoft, Windows, Windows Vista and Windows Media and logos are trademarks or registered trademarks of Microsoft Corporation in the

, DivX Certified® and

DivX associated logos are registered trademarks of DivX, Inc.

12 TONE ANALYSIS and its logo are trademarks of Sony Corporation.

“WALKMAN” and “WALKMAN” logo are registered trademarks of Sony Corporation.

SensMe and the SensMe logo are trademarks or registered trademarks of Sony Ericsson Mobile Communications AB.

Music recognition technology and related data are provided by Gracenote®. Gracenote is the industry standard in music recognition technology and related content delivery. For more information, please visit www.gracenote.com.

CD and music-related data from Gracenote, Inc., copyright © 2000-2010 Gracenote. Gracenote Software, copyright © 2000-2010 Gracenote. This product and service may practice one or more of the following U.S. Patents: #5,987,525; #6,061,680; #6,154,773, #6,161,132, #6,230,192, #6,230,207, #6,240,459, #6,330,593, and other patents issued or pending. Some services supplied under license from Open Globe, Inc. for U.S. Patent: #6,304,523.

Gracenote and CDDB are registered trademarks of Gracenote. The Gracenote logo and logotype, and the “Powered by Gracenote” logo are trademarks of Gracenote.

This product uses font data which is licensed to Sony by Monotype Imaging Inc. or its affiliates.

iPod is a trademark of Apple Inc., registered in the U.S. and other countries.

iPhone is a trademark of Apple Inc.

Apple, Macintosh and iTunes are trademarks of Apple Inc., registered in the U.S. and other countries.

THIS PRODUCT IS LICENSED UNDER THE MPEG-4 VISUAL PATENT PORTFOLIO LICENSE FOR THE PERSONAL AND NONCOMMERCIAL USE OF A CONSUMER FOR DECODING MPEG-4 VIDEO THAT WAS ENCODED BY A CONSUMER ENGAGED IN A PERSONAL AND NON-COMMERCIAL ACTIVITY AND/OR WAS OBTAINED FROM A VIDEO PROVIDER LICENSED BY MPEG LA TO PROVIDE MPEG-4 VIDEO. NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY OTHER USE. ADDITIONAL INFORMATION INCLUDING THAT RELATING TO PROMOTIONAL, INTERNAL AND COMMERCIAL USES AND LICENSING MAY BE OBTAINED FROM MPEG LA, LLC. SEE HTTP://WWW.MPEGLA.COM

Notes on Bluetooth

Caution

IN NO EVENT SHALL SONY BE LIABLE FOR ANY INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OR OTHER DAMAGES INCLUDING, WITHOUT LIMITATION, LOSS OF PROFITS, LOSS OF REVENUE, LOSS OF DATA, LOSS OF USE OF THE PRODUCT OR ANY ASSOCIATED EQUIPMENT, DOWNTIME, AND PURCHASER’S TIME RELATED TO OR ARISING OUT OF THE USE OF THIS PRODUCT, ITS HARDWARE AND/OR ITS SOFTWARE.

IMPORTANT NOTICE!

Safe and efficient use

Changes or modifications to this unit not expressly approved by Sony may void the user’s authority to operate the equipment. Please check for exceptions, due to national requirement or limitations, in usage of Bluetooth equipment before using this product.

Driving

Check the laws and regulations on the use of cellular phones and handsfree equipment in the areas where you drive. Always give full attention to driving and pull off the road and park before making or answering a call if driving conditions so require.

Connecting to other devices

When connecting to any other device, please read its user guide for detailed safety instructions.

Radio frequency exposure

RF signals may affect improperly installed or inadequately shielded electronic systems in cars, such as electronic fuel injection systems, electronic antiskid (antilock) braking systems, electronic speed control systems or air bag systems. For installation or service of this device, please consult with the manufacturer or its representative of your car. Faulty installation or service may be dangerous and may invalidate any warranty that may apply to this device. Consult with the manufacturer of your car to ensure that the use of your cellular phone in the car will not affect its electronic system. Check regularly that all wireless device equipment in your car is mounted and operating properly.

Emergency calls

This Bluetooth car handsfree and the electronic device connected to the handsfree operate using radio signals, cellular, and landline networks as well as user-programmed function, which cannot guarantee connection under all conditions. Therefore do not rely solely upon any electronic device for essential communications (such as medical emergencies). Remember, in order to make or receive calls, the handsfree and the electronic device connected to the handsfree must be switched on in a service area with adequate cellular signal strength. Emergency calls may not be possible on all cellular phone networks or when certain network services and/or phone features are in use. Check with your local service provider.

Playable discs and symbols used in this manual

This unit can play various video/audio discs. The following chart helps you to check if a disc is supported by this unit, as well as what functions are available for a given disc type.

Disc symbol in manual Disc format

DVD VIDEO

DVD-R*

/ DVD-R DL*1 / DVD-RW*

(Video mode/VR mode)

VIDEO

DVD+R*

/ DVD+R DL*1 / DVD+RW*

Video CD

(Ver. 1.0/1.1/2.0)

Audio CD

AUDIO

*1 Audio files can also be stored. *2 Video/image files can also be stored.

Note

“DVD” may be used in this manual as a general term for DVD VIDEOs, DVD-Rs/DVD-RWs, and DVD+Rs/ DVD +RWs.

CD-ROM*

/ CD-R*2 / CD-RW*

The following chart shows the supported compression formats and their file types. Available functions differ depending on the format, regardless of disc type. The format symbols below appear next to the description of functions available for that format.

Format symbol in manual File type

MP3 audio file

WMA audio file

AAC audio file

JPEG image file

DivX

video file

MPEG-4

Tip

For details on compression formats, see page 64.

Note

Even compatible discs may not be playable on this unit, depending on their recorded condition.

MPEG-4 video file

Location and function of controls

6 7 8 9

Main unit

VOL

2 3 4 5

Refer to the pages listed for details.

A Disc slot (located behind the front panel)

page 19

B VOL (Volume) –/+* buttons

C Receptor for the card remote

commander

D Display window/touch panel

E Reset button page 16

F (Bluetooth) signal indicator

page 38

TOP

G TOP button

To open the top menu.

H SOURCE/OFF button

Press to turn on the power/change the source: “Tuner” (Radio), “Disc,” “AUX” (Auxiliary equipment), “USB/iPod,” “BT Audio” (Bluetooth Audio). Press for 1 second to turn off the power. Press for more than 2 seconds to shut off completely.

I Z (Open/Close) button page 19

* The VOL + button has a tactile dot.

OFFSOURCE

Screen displays

When no source is selected:

A “Source List” key

To open the source list.

B “Top” key

To open the top menu.

Source List

Top menu:

45 67

ATT

AV Source BT Phone

Source list:

Top

12:00

M.OFF

12:00

C Clock display page 57, 61

D (Close) key

To close the menu.

E “ATT” (Attenuate) key*

To attenuate the sound. To cancel, touch again.

F (Setting) key

To open the setting menu.

G “M.OFF” (Monitor off) key

To turn off the monitor and the button illumination. To turn back on, touch anywhere on the display.

H “AV Source” key

To open the source list.

I “BT Phone” key

To enter the Bluetooth Phone mode.

J Source select keys

To change the source: “Tuner” (Radio), “Disc,” “AUX” (Auxiliary equipment), “USB/iPod,” “SensMe™,” “BT Audio” (Bluetooth Audio).

* Appears only when a source is selected.

45 62

ATT

Tuner Disc

USB/iPod

SensMe™

AUX

BT Audio

Top

12:00

Card remote commander RM-X170

8 9 q;

3 4

• The card remote commander can be generally used to operate the audio controls simply. For menu operations, use the touch panel.

• Refer to the pages listed for details.

• Remove the insulation film before use (page 16).

A OFF button

Press to turn off/stop the source. Press and hold to shut off completely.

B MONITOR OFF button

To turn off the monitor and the button illumination. To turn back on, press again.

qs qd

qf qg

E EQ (Equalizer) button

To select an equalizer curve from 7 music types (“Xplod”/“Vocal”/“Edge”/“Cruise”/ “Space”/“Gravity”/“Custom”/“OFF”).

F Number buttons page 28

Radio:

Press to receive stored stations. Press and hold to store stations.

Disc/USB:

To locate a title/chapter/track.

G CLEAR button

To delete an entered number.

C POSITION button

To switch the listening position (“Front L”/ “Front R”/“Front”/“All”/“Custom”/“OFF”).

D O (Return) button

To return to the previous display/return to the menu on a VCD*

H ATT (Attenuate) button

To attenuate the sound. To cancel, press again.

I u (Play/Pause) button

J .m/M> buttons

Radio:

Press to tune in stations automatically. Press and hold to find a station manually. Disc*2/USB: Press to skip a chapter/track/scene/file. Press and hold momentarily to reverse/fastforward the video. Press and hold to reverse/fast-forward track. Bluetooth Audio*3: Press to skip a track. Press and hold to reverse/fast-forward track.

K DVD playback setting buttons

(AUDIO):

To change the audio language/format. (For VCD/CD/MP3/WMA/AAC/MPEG-4, to change the audio channel.)

(SUBTITLE):

To change the subtitle language.

(ANGLE):

To change the viewing angle.

(TOP MENU):

To open the top menu on a DVD.

(MENU):

To open the menu on a disc.

L ZAP button

To enter the ZAPPIN™ mode.

M </M/m/, (Cursor)/ENTER buttons

page 19

To control the menu on a DVD.

*1 When playing with PBC function. *2 Operation differs depending on the disc (page 21). *3 Operation differs depending on the connected

Bluetooth device.

*4 When two auxiliary devices are used.

Note

If the unit is turned off and the display disappears, it cannot be operated with the card remote commander unless (SOURCE/OFF) on the main unit is pressed, or a disc is inserted to activate the unit first.

N SRC (Source) button

To turn on/change the source: “Tuner” (Radio), “Disc,” “AUX” (Auxiliary equipment), “USB/iPod,” “BT Audio” (Bluetooth Audio).

O MODE button

Press to select the radio band (FM/MW/LW)/ select an auxiliary device (AUX1/AUX2)*

P VOL (Volume) +/– buttons

Getting Started

Resetting the unit

Before operating the unit for the first time, or after replacing the car battery or changing the connections, you must reset the unit. Press the reset button (page 12) with a pointed object, such as a ball-point pen.

Note

Pressing the reset button will erase the clock setting and some stored contents.

Performing initial settings

After resetting, the display for the initial settings appears.

Initial Setting

Subwoofer

Listening Position

Language

1 Touch “Subwoofer” to set the

subwoofer connection status.

Set to “ON” if a subwoofer is connected, or “OFF” if not.

2 Touch “Listening Position” to set the

listening position.

Set to “Front L” if your listening position is front left, or “Front R” if front right.

3 Touch “Language” to set the display

language.

Touch repeatedly until the desired language (English/Spanish/Russian) appears.

4 Touch “OK.”

The setting is complete.

This setting can then be further configured in the setting menu.

• For details on setting the subwoofer connection status, see page 56.

• For details on setting the listening position, see “Optimizing sound for the listening position — Intelligent Time Alignment” on page 49.

• For details on setting the display language, see page 54.

OFF / ON

Front L / Front R

English

Preparing the card remote commander

Before using the card remote commander for the first time, remove the insulation film.

Basic Operations

Listening to the radio

Touch “Source List,” then “Tuner.”

From the top menu, touch “AV Source,” then “Tuner.” The radio reception display appears.

Touch “Band.”

The band list appears.

ATTSource List

TA AF To p

P1 P2 P3

P4 P5 P6

Band

ATT

Source List

TA AF To p

Receive

Preset

List

BTM

Memory

PTY List

12:0015

FM2 FM3 LW

FM1

Receive

Band

Touch the desired band (“FM1,” “FM2,” “FM3,” “MW” or “LW”).

Touch “Band” to close the band list.

Perform tuning.

To tune automatically

Touch

./>.

Scanning stops when the unit receives a station. Repeat this procedure until the desired station is received.

To tune manually

Touch

m/M repeatedly until the desired frequency is received.

To skip frequencies continuously, touch and hold

m/M.

continue to next page t

Preset

PTY

List

12:0015

Reception controls

2 3 4 5

Touch the display if the reception controls are not shown.

ATT

Source List

TA AF To p

Band

Receive

Preset

List

PTY

List

12:0015

678

9 0 qa

No. Item Touch to

1 “Source List” open the source list. (page 13) 2 “ATT” attenuate the sound. To cancel, touch again. 3 “TA” set TA in RDS. (page 24) 4 “AF” set AF in RDS. (page 24) 5 “Top” open the top menu. (page 13) 6 m/M tune manually.

Touch and hold to skip frequencies continuously.

7 ./> tune automatically. 8 “Band” open the band list and change the band. 9 “Receive Menu” open the receive menu, which contains the following.

• “Mono”: Touch to activate the monaural mode if FM reception

is poor. To restore stereo reception, select “OFF.”

• “Local”: Touch to only tune into stations with stronger signal.

To tune normal stations, select “OFF.”

• “Regional” (page 24)

0 “Preset List” list up stored stations, or store stations. (page 23) qa “PTY List” open the PTY list. (page 24)

Indications during reception

ATT

Source List

TA AF To p

Receive

Band

Preset

List

A Current source icon* B Band number, Preset number*2, Frequency*3/status C Volume level* D Setting status (CSO, EQ7, RBE)

*1 Appears only when the controls are shown. *2 Appears only when the station stored in memory is

received.

*3 While receiving an RDS station, program service name

appears. For details, see “RDS” on page 23.

PTY List

*4 When ATT is activated, appears.

12:0015

Playing discs

Depending on the disc, some operations may be different or restricted. Refer to the operating instructions supplied with your disc.

Press Z on the main unit.

The front panel opens automatically.

Insert the disc (label side up).

The front panel closes automatically, then playback starts.

If the DVD menu appears

Touch the item in the DVD menu directly. You can also use the menu control panel which can be shown by touching the display in a place other than menu item area. Touch b/v/V/B to move the cursor, then “Enter” to confirm. If the menu control panel does not appear by touching the display, use the card remote commander.

About the DVD menu

A DVD is divided into several sections, which make up a picture or music feature. These sections are called “titles.” When you play a DVD that contains several titles, you can select a desired title using the DVD’s top menu. For DVDs that allow you to select items such as subtitle/sound language(s), select these items using the DVD menu.

If the disc contains JPEG files

The slide show starts automatically.

To stop playback

Press (SOURCE/OFF) for 1 second.

Note

Discs in DTS format are not supported. The sound is not output if the DTS format is selected.

To eject the disc

1 Press Z on the main unit.

The front panel opens automatically, then the disc is ejected.

2 Press Z on the main unit to close the front panel.

Note

The front panel closes automatically after the caution alarm sounds.

continue to next page t

Playback controls

2 3 4 5

Touch the display if the playback controls are not shown.

Common to all discs/formats

Source List

ATT TA AF Top

Play Menu

DVD

SHUF

Control

ATT TA AF Top

PBC Panel

Play Menu

SHUF

ATT

TA AF To p

Source List

12:0015

Source List

12:0015

ATT TA AF Top

Play Menu

DVD

SHUF

Control

MPEG-4

ATT

TA AF To p

Play Menu

List

Album

SHUF

12:0015

Album

ZAP

SHUF

12:0015

Play Menu

List

No. Item Touch to

6 ./> skip a chapter/track/scene/image/file.

Touch and hold momentarily to reverse/fast-forward the video; and then repeatedly to switch the speed (× 2 t × 12 t × 120 t × 2…)*

. To cancel, touch u. Touch and hold to reverse/fast-forward the audio track. During pause, touch and hold down > to play the video in

slow motion. To cancel, release the key.

7 u pause/resume play after pause. 8 “Play Menu” open the play menu, which contains the following.

• “Repeat”/“Shuffle” (page 27)

• “Dolby D Level” (DVD VIDEO playback only) (page 26)

• “Stereo” (VCD/CD/MP3/WMA/AAC playback only)

(page 26)

• “Image Turn” (JPEG playback only): Touch to rotate an

image left/right.

• “Audio” (DivX/MPEG-4 playback only) (page 25, 26)

• “Subtitle” (DivX playback only): Touch repeatedly to turn off/

select the subtitle language.*2*

9 “DVD Control” open the DVD control menu, which contains the following.

• “Audio”: Touch repeatedly to select the audio language/

format. (page 25)*

• “Subtitle”: Touch repeatedly to turn off/select the subtitle

language.*

• “Angle”: Touch repeatedly to change the viewing angle.*

• “Top Menu”: Touch to open the top menu on the DVD.*

• “Menu”: Touch to open the menu on the disc.*

2*3

0 “PBC Panel” show the control panel for the PBC menu. (page 25) qa “Album” –/+ skip an album (folder) of MP3/WMA/AAC/JPEG/DivX/

MPEG-4.

qs “List” list up tracks/images/video files. (page 36) qd “ZAP” enter the ZAPPIN mode. (page 36)

*1 The speed depends on the format or the recording method. *2 Unavailable depending on the disc. *3 When the 4-digit input prompt appears, input the language code (page 73) for the desired language.

Note

If the disc contains multiple file types, only the selected file type (audio/video/image) can be played. For details on how to select the file type,

Notes on JPEG playback

• If a large-sized image is rotated, it may take longer to display.

• Progressive JPEG files cannot be displayed.

see “Selecting a file type” on page 36.

continue to next page t

Indications during playback

D E F

Touch the display to show the indications. For audio discs, some indications are always shown during playback.

Source List

ATT TA AF Top

DVD

Control

B C

ATT

TA AF To p

List

ZAP

Album

MPEG-4

Play Menu

SHUF

Play Menu

SHUF

A Current source icon B Volume level* C Format, Playback status, Elapsed playback

time* number* (CSO, EQ7, RBE)

D Playback status, Elapsed playback time* E Track name, Album name, Artist name F Album artwork display*

, Chapter/title/album (folder)/track

3*4

, Audio Format*5, Setting status

G Format, Track number, Album number*7, Setting

status (CSO, EQ7, RBE)

12:0015

*1 When ATT is activated, appears. *2 During JPEG playback or VCD playback with the PBC

function, no indication appears.

*3 Indications differ depending on the disc/format. *4 When playing a VCD with the PBC function (page 25),

no indication appears.

*5 DVD/DivX only. *6 The recommended size is from 240 × 240 to 960 × 960

pixels.

*7 MP3/WMA/AAC only.

Advanced Operations — Radio

Display items

Storing and receiving stations

Caution

When tuning in stations while driving, use Best Tuning Memory (BTM) to prevent an accident.

Storing automatically — BTM

1 Touch “Source List,” then “Tuner.”

To change the band, touch “Band,” then select the desired band (“FM1,” “FM2,” “FM3,” “MW” or “LW”).

2 Touch “Preset List,” then “BTM.”

The unit stores stations in order of frequency in the preset list (“P1” to “P6”). A beep sounds when the setting is stored.

Storing manually

1 While receiving the station that you

want to store, touch “Preset List.”

2 Touch “Memory,” then touch the

number in the list (“P1” to “P6”).

The number and the confirmation display appear on the display.

3 Tou ch “ Yes.”

The station is stored.

Note

If you try to store another station on the same number, the previously stored station will be replaced.

Tip

When an RDS station is stored, the AF/TA setting is also stored (

page 24).

Receiving stored stations

1 Select the band, then touch “Preset

List.”

2 Touch the desired number (“P1” to

“P6”).

RDS

Overview

FM stations with Radio Data System (RDS) service send inaudible digital information along with the regular radio program signal.

ATT

Source List

A Band number, Preset number, Frequency

(Program service name), RDS data, TA*

B Stereo*2, RDS*3, TP*

TA AF To p

Receive

Preset

List

Band

PTY List

12:0015

C Clock display

*1 During traffic information. *2 During FM reception. *3 During RDS reception. *4 During traffic program reception.

RDS services

This unit automatically provides RDS services as follows:

AF (Alternative Frequencies)

Selects and retunes the station with the strongest signal in a network. By using this function, you can continuously listen to the same program during a long-distance drive without having to retune the same station manually.

TA (Traffic Announcement)/TP (Traffic Program)

Provides current traffic information/programs. Any information/program received, will interrupt the currently selected source.

PTY (Program Types)

Displays the currently received program type. Also searches your selected program type.

CT (Clock Time)

The CT data from the RDS transmission sets the clock.

Notes

• Depending on the country/region, not all RDS functions may be available.

• RDS will not work if the signal strength is too weak, or if the station you are tuned to is not transmitting RDS data.

Setting AF and TA

1 During reception/playback, touch “AF”

or “TA” to activate.

When activated, the key color changes. To deactivate, touch again.

Storing RDS stations with the AF and TA setting

You can preset RDS stations along with the AF/ TA setting. If you use the BTM function, only RDS stations are stored with the same AF/TA setting. If you preset manually, you can preset both RDS and non-RDS stations with the AF/TA setting for each.

1 Set AF/TA, then store the station with BTM or

manually.

Receiving emergency announcements

With AF or TA on, the emergency announcements will automatically interrupt the currently selected source.

Tip

If you adjust the volume level during a traffic announcement, that level will be stored into memory for subsequent traffic announcements, independently from the regular volume level.

Staying with one regional program — Regional

When the AF function is on: this unit’s factory setting restricts reception to a specific region, so you will not be switched to another regional station with a stronger frequency.

If you leave this regional program’s reception area, deactivate the regional function during FM reception. Touch “Receive Menu,” then the “Regional” box to set to “OFF.”

Note

This function does not work in the UK and in some other areas.

Local Link function (UK only)

This function enables you to select other local stations in the area, even if they are not stored on numbers.

1 During FM reception, touch “Preset List,” then

a number (“P1” to “P6”) on which a local station is stored.

2 Within 5 seconds, touch again the number of

the local station. Repeat this procedure until the local station is received.

Selecting PTY

1 During FM reception, touch “PTY List.”

The PTY list appears if the station is transmitting PTY data. To scroll the list, touch v/V.

2 Touch the desired program type.

The unit searches for a station broadcasting the selected program type.

To close the PTY list, touch “PTY List.”

Type of programs

“News” (News), “Current Affairs” (Current Affairs), “Information” (Information), “Sport” (Sports), “Education” (Education), “Drama” (Drama), “Cultures” (Culture), “Science” (Science), “Varied Speech” (Varied), “Pop Music” (Pop Music), “Rock Music” (Rock Music), “Easy Listening”

(M.O.R. Music), “Light Classics M” (Light classical), “Serious Classics” (Serious classical), “Other Music” (Other Music), “Weather & Metr” (Weather), “Finance” (Finance), “Children’s Progs” (Children’s program), “Social Affairs” (Social Affairs), “Religion” (Religion), “Phone In” (Phone In), “Travel & Touring” (Travel), “Leisure & Hobby” (Leisure), “Jazz Music” (Jazz Music), “Country Music” (Country Music),

“National Music” (National Music), “Oldies Music” (Oldies Music), “Folk Music” (Folk Music), “Documentary” (Documentary)

Note

You cannot use this function in countries/regions where no PTY data is available.

Setting CT

1 Set “CT” to “ON” in setting (page 54).

Notes

• The CT function may not work even though an RDS station is being received.

• There might be a difference between the time set by the CT function and the actual time.

Advanced Operations — Discs

Using PBC functions — Playback control

The PBC menu interactively assists with operations while a PBC compatible VCD is played.

1 Start playing a PBC compatible VCD.

The PBC menu appears.

2 Touch “PBC Panel.”

The menu control panel appears.

3 Touch the number keys to select the

desired item, then “Enter.”

4 Follow the instructions in the menu for

interactive operations.

To return to the previous display, press O. To hide the controls, touch “Close.”

Playing without the PBC function

1 While the unit is off, touch “Source

List,” then

2 Touch “Visual.”

The visual setting menu appears.

3 Tou ch v/V to scroll, then “Video CD

PBC” to set to “OFF.”

4 Start playing a VCD.

The PBC menu does not appear during playback.

Notes

• The items on the menu, and operation procedures differ depending on the disc.

• During PBC playback, the track number, playback item, etc., do not appear in the playback display.

• Resume playback is unavailable during playback without PBC.

Configuring audio settings

Note

Discs in DTS format are not supported. The sound is not output if the DTS format is selected.

Changing the audio language/ format

For DVD, the audio language can be changed if the disc is recorded with multilingual tracks. For DVD/DivX, you can change the audio format when playing a disc recorded in multiple audio formats (e.g., Dolby Digital).

For DVD

1 During playback, touch “DVD Control.” 2 Touch “Audio” repeatedly until the

desired audio language/format appears.

Audio language

Source List

Audio 1: English Dolby D 3/2.1

Audio Subtitle Angle MenuTop Menu

ATT TA AF Top

Play Menu

DVD

SHUF

Control

Audio format/channel numbers*

12:0015

The audio language switches among the available languages. When the 4-digit input prompt appears, input the language code (

page 73) for the desired language. When the same language is displayed two or more times, the disc is recorded in multiple audio formats.

* The format name and channel numbers appear as

follows. Example: Dolby Digital 5.1 ch

Rear component × 2

Dolby D 3 / 2 . 1

Front component × 2 + Center component × 1

To close the DVD control menu, touch “DVD Control.”

For DivX

1 During playback, touch “Play Menu,”

then “Audio” repeatedly until the desired audio format appears.

To close the play menu, touch “Play Menu.”

LFE component × 1

Changing the audio channel

When playing VCD/CD/MP3/WMA/AAC/ MPEG-4, you can select the right or left channel sound to listen through both right and left speakers. The options are indicated below.

“2-Ch”: Standard stereo sound (default) “L-Ch”: Left channel sound (monaural) “R-Ch”: Right channel sound (monaural)

For VCD/CD/MP3/WMA/AAC

MPEG-4

1 During playback, touch “Play Menu,”

then “Stereo” repeatedly until the desired audio channel appears.

For MPEG-4

1 During playback, touch “Play Menu,”

then “Audio” repeatedly until the desired audio channel appears.

To close the play menu, touch “Play Menu.”

Note

You may not be able to change the audio setting depending on the disc.

Tip

The operation by the card remote commander (pressing (AUDIO) repeatedly) is also available.

Locking discs — Parental control

* Excluding DVD-R/DVD-R DL/DVD-RW in VR mode.

You can lock a disc, or set playback restrictions according to a predetermined level such as viewer age. Restricted scenes can be blocked or replaced with different scenes when a parental control compatible DVD is played.

Activating parental control

1 While the unit is off, touch “Source

List,” then

2 Touch “Visual.”

The visual setting menu appears.

3 Touch v/V to scroll, then “DVD

Parental Control.”

The password setting display appears.

4 Touch the number keys to enter your

password, then “OK.”

5 To confirm, touch the number keys to

reenter your password, then “OK.”

The setting is complete.

To delete an entered number, touch “Clear.” To return to the previous display, touch “Back.”

Adjusting the audio output level — Dolby D level

You can adjust the audio output level for a DVD recorded in Dolby Digital format, to reduce the volume level differences between disc and source.

1 During playback, touch “Play Menu.” 2 Touch the “Adjust” box to set to “ON.” 3 Touch –/+ repeatedly to adjust the

output level.

The output level is adjustable in single steps, between –10 and +10.

To close the play menu, touch “Play Menu.”

Deactivating parental control

1 Follow steps 1 to 3 above.

The parental unlock display appears.

2 Touch the number keys to enter your current

password. “Parental Unlocked” appears, and the parental control is deactivated.

Changing the password

Deactivate the parental control, then activate again using the new password.

Changing the area and its movie rating level

The restriction levels can be set depending on the area and its movie ratings.

1 While the unit is off, touch “Source

List,” then

2 Touch “Visual.”

The visual setting menu appears.

3 Tou ch v/V to scroll, then “DVD

Parental Area.”

When parental control is already activated, the display to enter your password appears. To change the setting, enter your password. The options appear.

4 Touch the desired area to apply its

movie ratings.

When you select “Other,” enter the area code selecting from

“Area code list” on page 73,

using the number keys.

5 Touch “DVD Parental Rating.”

The options appear. The lower the number, the stricter the restriction level.

6 Touch the desired rating.

The setting is complete.

To return to the previous display, touch “Back.”

Repeat and shuffle play

1 During playback, touch “Play Menu,”

then the “Repeat” or “Shuffle” box repeatedly until the desired option appears.

Source List

Chapter OFF ON

Repeat Shuffle Adjust Dolby D Level 0

Repeat or shuffle play starts.

To close the play menu, touch “Play Menu.” The repeat options and switching order of each

disc/format are indicated below.

Disc/format Options

MPEG-4

ATT TA AF Top

“OFF”: Returns to normal play

mode. “Chapter”: Repeats the current chapter. “Title”: Repeats the current title.

“OFF”: Returns to normal play

mode. “Track”: Repeats the current track.

“OFF”: Returns to normal play mode. “Track”: Repeats the current track. “Album”: Repeats the current album (folder).

“OFF”: Returns to normal play mode. “Image”: Repeats the current image. “Album”: Repeats the current album.

“OFF”: Returns to normal play mode. “Movie”: Repeats the current video file. “Album”: Repeats the current album (folder).

MPEG-4

DVD

Control

Play Menu

SHUF

12:0015

continue to next page t

The shuffle options and switching order of each disc/format are indicated below.

Disc/format Options

“OFF”: Returns to normal play

mode.

“Title”: Plays chapters in current title in random order.

“OFF”: Returns to normal play

mode. “Disc”: Plays tracks in current disc in random order.

“OFF”: Returns to normal play mode. “Album”: Plays tracks/images/ video files in current album (folder) in random order.

MPEG-4

*1 Available only when playing version 1.0/1.1 VCD,

or version 2.0 VCD without PBC function.

*2 Excluding DVD-R/DVD-R DL/DVD-RW in VR

mode.

Direct search play

You can directly locate a desired point by specifying the title number, chapter number, etc.

1 During playback, press the number

buttons on the card remote commander to enter an item (track, title, etc.) number, then press (ENTER).

Playback starts from the beginning of the selected point.

The search items of disc/format are as follows.

DVD: Title or chapter* VCD*2/CD/MP3/WMA/AAC: Track JPEG: Image DivX/MPEG-4: File

*1 The search item depends on the setting. *2 Available only when playing a VCD without PBC

function.

Setting the search item (DVD only)

You can set the search item (title or chapter) for DVD playback.

1 Touch “Source List,” then . 2 Touch “Visual.”

The visual setting menu appears.

3 Touch v/V to scroll, then “DVD Direct

Search” to set to “Chapter” or “Title.”

The setting is complete.

To return to the previous display, touch “Back.”

MPEG-4

USB Device Operations

For details on the compatibility of your USB device, visit the support site.

Support site

http://support.sony-europe.com/

• MSC (Mass Storage Class) and MTP (Media Transfer Protocol) type USB devices compliant with the USB standard can be used.

• Corresponding codec is MP3 (.mp3), WMA (.wma), AAC (.m4a), JPEG (.jpg), DivX (.avi) and MPEG-4 (.mp4).

• Backup of data in a USB device is recommended.

Notes

• Connect the USB device after starting the engine. Depending on the USB device, malfunction or damage may occur if it is connected before starting the engine.

• A large-sized file may take time to start playing back.

Notes on use

• Do not use USB devices so large or heavy that they may fall down due to vibration, or cause a loose connection.

• Do not leave a USB device in a parked car, as malfunction may result.

• This unit cannot recognize USB devices via a USB hub.

Notes on playback

• If a USB device contains multiple file types, only the selected file type (audio/video/image) can be played. For details on how to select the file type, “Selecting a file type” on page 36.

• Displayed indications will differ, depending on the USB device, recorded format and settings. For details, visit the support site.

• The maximum number of displayable data is as follows. – folders (albums): 256 – files (tracks): 2,000

• It may take time for playback to begin, depending on the amount of recorded data.

• During playback or fast-forward/reverse of a VBR (Variable Bit Rate) MP3/WMA/AAC file, elapsed playing time may not display accurately.

• Playback of a lossless compression file is not supported.

see

Playing a USB device

1 Remove the cap from the USB

connector, and connect the USB device to the USB connector.

Playback starts automatically. If a USB device is connected, to start playback, touch “Source List,” then “USB/ iPod.”

For details on the location of the USB connector, see the supplied installation/connections manual.

About the controls and indications during playback

You can control USB playback in the same way as disc playback. For details, see “Playback controls” on page 20. For details on indications during playback, see “Indications during playback” on page 22.

To stop playback

Press (SOURCE/OFF) for 1 second.

To disconnect the USB device

Stop playback, then disconnect. Do not disconnect during playback, as data in the USB device may be damaged.

Repeat and shuffle play

1 During playback, touch “Play Menu,”

then the “Repeat” or “Shuffle” box repeatedly until the desired option appears.

Repeat or shuffle play starts.

The repeat options are as follows.

“OFF”: Returns to normal play mode. “Track”/“Image”/“Movie”*1: Repeats the

current track/image/video file.

“Album”: Repeats the current album (folder). “Drive”*2: Repeats the current drive.

The shuffle options are as follows.

“OFF”: Returns to normal play mode. “Album”: Plays tracks/images/video files in the

current album (folder) in random order.

*1 Options depend on the file type. *2 When two or more drives are created on the USB

device.

To close the play menu, touch “Play Menu.”

Enjoying music according to your mood — SensMe™

Sony’s unique “SensMe™ channels” and “SensMe™ mood” features automatically group tracks by channel or mood, and allow you to enjoy music intuitively.

Before using the SensMe™ function

The following is the basic procedure required to enjoy the SensMe™ function on the unit.

1Installing “SensMe™ Setup” and

“Content Transfer” in your computer

First install “SensMe™ Setup” and “Content Transfer” from the supplied CD-ROM.

™

Content

SensMe

Transfer

Setup

2Registering a USB device using

“SensMe™ Setup”

Connect a USB device to your computer, and perform registration using “SensMe™ Setup” to enable the SensMe™ function on this unit.

3 Transferring tracks to the USB device

using “Content Transfer”

In order to group tracks by channel or mood, track sound patterns need to be analyzed by 12 TONE ANALYSIS, which is loaded in “Content Transfer.” With the USB device connected to your computer, drag and drop tracks from Windows Explorer or iTunes, etc., to “Content Transfer.” Both analysis and transfer of tracks will be performed by “Content Transfer.”

Content Transfer

4 Connecting the USB device and

enjoying the SensMe™ function on the unit

Connect the set up USB device. You can then enjoy “SensMe™ channels” or “SensMe™ mood” on this unit.

SensMe™

™

SensMe

Setup

Tip

Registration can be performed either along with the installation procedure or after installation.

Installing “SensMe™ Setup” and “Content Transfer” in your computer

Use of the supplied software (“SensMe™ Setup” and “Content Transfer”) is required to enable the SensMe™ function on this unit. Install the software in your computer from the supplied CD-ROM.

1 Insert the supplied CD-ROM into your

computer.

The Installation Wizard runs automatically.

2 Follow the on-screen instructions to

complete the installation.

+ 210 hidden pages