Sony WM-FS220 Service manual
WM-FS220
SERVICE MANUAL
Ver 1.0 2000. 02
SPECIFICATIONS
Radio Frequency FM : 87.5 – 108 MHz
AM : 531 – 1,602 kHz
Power Requirements 3 V DC Batteries R6 (AA) × 2
Dimensions (w/h/d) Approx. 108.4 × 125.7 × 47.2 mm
(4 3/8 × 5 × 1 7/8 inches) incl.
projecting parts and controls
Mass Approx. 280 g (9.9 oz)/Approx. 355 g (12.6 oz)
(incl. batteries and a cassette)
Supplied Accessories • Stereo headphones or earphones (1)
• Belt clip (1)
Canadian Model
Model Name Using Similar Mechanism NEW
T ape Transport Mechanism Type MF-WMFS220-114
Design and specifications are subject to change without notice.
RADIO CASSETTE PLAYER
TABLE OF CONTENTS
1. GENERAL ··········································································2
2. SERVICE NOTE······························································· 3
3. DISASSEMBLY
3-1. Main Assembly ······························································ 4
3-2. Chassis Sub Assy··························································· 5
3-3. Main Board and Mechanism Deck ································ 5
3-4. Belt ················································································ 6
3-5. Head, Magnetic (HP901) ··············································· 6
4. MECHANICAL ADJUSTMENT ·································· 7
5. ELECTRICAL ADJUSTMENT ···································· 7
6. DIAGRAMS
6-1. IC Block Diagrams ······················································ 10
6-2. Block Diagram ···························································· 11
6-3. Schematic Diagram ····················································· 13
6-4. Printed Wiring Board··················································· 15
6-5. IC Pin Function Description ········································ 17
7. MEXPLODED VIEWS
7-1. Cabinet Assy Section··················································· 18
7-2. Main Board Section ····················································· 19
7-3. Mechanism Deck Section-1
(MF-WMFS220-114) ·················································· 20
7-4. Mechanism Deck Section-2
(MF-WMFS220-114) ·················································· 21
8. ELECTRICAL PPARTS LIST ···································· 22
SECTION 1
GENERAL
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be
damaged by heat.
This section is extracted
from instruction manual.
Flexible Circuit Board Repairing
• Keep the temperature of soldering iron around 270˚C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
— 2 —
WATER PROOF SECTION
)
SECTION 2
SERVICE NOTE
Note : In case the parts in the figure are removed for repair, treat them to protect from water drop following the instructions in the figure
• Sony grease SGL-601 : 7-651-000-10
(spread grease, bond etc.)
Ring (Dia. 2.5 × Dia. 4.5). O
(Apply sony grease: SGL-601)
Tapping screw (B)(1.4 × 4)
Joint (AVLS)
Tapping screw (B)(1.4
Joint (VOL)
Ring. O
(Apply sony grease: SGL-601
Knob (Vol)
×
4)
Knob (Hold)
— 3 —
SECTION 3
)
r
)
DISASSEMBLY
Note : Disassemble the unit in the order as shown below.
Set
Main Assembly
Note : Follow the disassembly procedure in the numerical order given.
3-1. MAIN ASSEMBLY
6
Remve the main assembly in the direction
of arrow.
(Be careful not to focibly pull the wire that connects
the main board and the headphone board.)
7
Remove the headphone
borad in the direction of arrow.
Chassis Sub Assy
Main Board and Mechanism Deck
5
Two screws (+B1.7 × 7)
Belt
Head, Magnetic (HP901
4
Cassette sub assembly, holde
3
Screw, tapping
CAUTION WHEN ASSEMBLING THE MAIN ASSEMBLY
• Assemble the main assembly in a way that each switch mates with the corresponding knob each other.
POWER switch (S303)
DIR switch (S301)
2
Screw, tapping
1
Stop ring (E 1.2)
DX/LOCAL switch
(S304)
— 4 —
Volume (RV301
3-2. CHASSIS SUB ASSY
s
2
Knob (DX-Local)
Main board
1
Two claw
3-3. MAIN BOARD AND MECHANISM DECK
4
Main board
2
Remove the solder
3
Chassis sub assy
3
Screw (M1.4 ) Toothed Lock
1
Remove the solder (fouf points)
5
Stopper (MD)
— 5 —
6
Mechanism deck
3-4. BELT
Belt
Belt threading
3-5. HEAD, MAGNETIC (HP901)
1
Two screws (M1.4)
Capstan wheel assy(SP)
Belt
Reel/Capstan motor
2
Head, magnetic (HP901)
— 6 —
Loading...