Sony WEGA KV-SW21 Operating Instructions Manual

2-630-056-12 (2)

Trinitron Color TV

Operating Instructions

• Before operating the unit, please read this manual thoroughly and retain it for future reference.

KV-SW21

N63 N60 N50

A Specifications

Power requirements Power consumption (W) Television system Color system Stereo/Bilingual system

Channel coverage 8 (Antenna) Audio output (Speaker) 3D Woofer Number of terminal

(Video)

(Audio)

(Component

Video)

i (Headphone)

FM Radio

Tuning Range Intermediate

Frequency

Picture tube

Tube size

Viewing screen size Dimensions (w/h/d) Mass

KV-SW21N63

110-240 V AC, 50/60 Hz Indicated on the rear of the TV M NTSC3.58, PAL*, PAL 60*, SECAM*, NTSC 4.43* * AV IN only MTS KV-SW21N63/

VHF : 2 to 13 /UHF : 14 to 69 /CATV : 1 to 125 75-ohm external terminal

4 W + 4 W 5 W + 5 W

12 W –

Input: 2 Output: 1 Phono jacks; 1 Vp-p, 75 ohms Input: 3 Output: 1 Phono jacks; 500 mVrms Input: 1 Phono jacks;

Output: 1 Stereo minijack

87.5 - 108.0 MHz KV-SW21N63/

7.9 MHz

21 in. 545 mm 507 mm

647 × 533 × 530 mm 647 × 469 × 509 mm

29 kg 25 kg

KV-SW21N60 KV-SW21N50

Y: 1 Vp-p, 75 ohms, sync negative C

B: 0.7 Vp-p, 75 ohms

R: 0.7 Vp-p, 75 ohms

Note

SW21N60 only

Measured diagonally Measured diagonally

Design and specifications are subject to change without notice.

B WARNING

• Dangerously high voltages are present inside the TV.

• TV operating voltage: 110 – 240 V AC.

• Do not plug in the power cord until you have completed making all other connections; otherwise a minimum leakage current might flow through the antenna and other terminals to ground.

• To avoid battery leakage and damage to the remote, remove the batteries from the remote if you are not going to use it for several days. If any liquid leaks from the batteries and touches your skin, immediately wash it away with water.

For your own safety, do not touch any part of the TV, the power cord and the antenna cable during lightning storms.

Do not place any objects on the TV. The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.

Do not block the ventilation openings of the TV. Do not install the TV in a confined space, such as a bookcase or built-in cabinet.

Do not open the cabinet and the rear cover of the TV as high voltages and other hazards are present inside the TV. Refer servicing and disposal of the TV to qualified personnel.

For children’s safety, do not leave children alone with the TV. Do not allow children to climb onto it.

Do not operate the TV if any liquid or solid object falls into it. Have it checked immediately by qualified personnel only.

Your TV is recommended for home use only. Do not use the TV in any vehicle or where it may be subject to excessive dust, heat, moisture or vibrations.

Clean the TV with a dry and soft cloth. Do not use benzine, thinner, or any other chemicals to clean the TV. Do not attach anything (e.g., adhesive tape, cellophane tape, glue) on the painted cabinet of the TV. Do not scratch the picture tube.

To prevent fire or shock hazard, do not expose the TV to rain or moisture.

Install the TV on a stable TV stand and floor which can support the TV set weight. Ensure that the TV stand surface is flat and its area is larger than the bottom area of the TV.

Do not plug in too many appliances to the same power socket. Do not damage the power cord.

Pull the power cord out by the plug. Do not pull the power cord itself. Even if your TV is turned off, it is still connected to the AC power source (mains) as long as the power cord is plugged in. Unplug the TV before moving it or if you are not going to use it for several days.

C Securing the TV

To prevent the TV from falling, use the supplied screws, clamps and band to secure the TV. Use only the supplied screws. Use of other screws may damage the TV.

20 mm

screws

3.8 mm clamps band

Screw the band to the TV stand and to the provided hole at the rear of your TV.

(1) Put a cord or chain through the clamps. (2)

Screw one clamp to a wall or pillar and the other clamp to the provided hole at the rear of your TV.

D Getting Started

Step 1

Insert the batteries (supplied) into the remote.

Note

•Do not use old or different types of batteries together.

Step 2

Connect the antenna cable (not supplied) to 8 (antenna input) at the rear of the TV.

Tips

•Your TV can receive both TV and FM radio signals from the appropriate

connections through the 8 (antenna input) terminal (KV-SW21N63/ SW21N60 only) (see H).

•You can also connect your TV to other optional components (see H).

Step 3

Plug in the power cord, then press ! on the TV to turn it on.

Note

•The 1 (standby) indicator flashes green for a few seconds when turning on the TV. This does not indicate a malfunction.

Step 4

Set up the TV by following the instructions of the “Initial Setup” menu (see E).

End

Confirm

Select

End

Select

Confirm

End

Select

Confirm

Program:

Searching...

End

Program Edit

2 3 4

Off Off Off

Edit:

PROG

SkipLabel

Exit

Select

Confirm

Off

Setting up your TV (“Initial Setup”)

When you turn on your TV for the first time, the “Initial Setup” menu will appear. You may change the menu language, preset the TV channels automatically, edit the channels and adjust the picture position using the buttons on the remote control or TV top control panel.

Press V or v to select the desired menu

language, then press

The selected menu language appears.

Press V or v to select “Yes”, then press to

preset the channels automatically.

The screen will indicate automatic presetting is in progress.

After all available channels have been tuned and stored, the “Program Edit” menu appears automatically on the screen.

To skip automatic channel presetting, select “No”, then press

If the message “No channel found. Please connect cable/antenna” appears, check your TV connections, then press .

The “Program Edit” menu enables you to

edit the channels.

a) If you wish to keep the channels in the current

condition, press WEGA GATE to exit.

b) Press V or v to select the program

number with the channel you wish to change. The selected channel will appear on the screen.

c) If you wish to edit the channels, press

to enter edit mode. Press b until the mode that you wish to edit is highlighted: Label, Skip, (block symbol). Then press

1) To label, press V or v to select the

alphanumeric characters for the label.

Then press

Select

Confirm

Exit

Setting up your TV (“Initial Setup”) (continued)

2) To skip the program number, press V or v to

select “On”. Then press You can skip this program number when

using PROG +/-.

3) To block unwanted program number,

press V or v to select

d) Repeat step b) to c) if you wish to change other

channels.

Press WEGA GATE to go to the next menu.

Press B or b to adjust the bars on the top

and bottom of the menu if they are slanted, then press

If no adjustment is necessary, then press

To prevent this “Initial Setup” menu from

appearing again when you turn on the TV by pressing !, press V or v to select “No”, then press

To allow this menu to appear again, select “Yes”, then press

. Then press .

Select

Confirm

Exit

End

Tip

• You can immediately go to the end of the ”Initial Setup” menu by pressing WEGA GATE.

TV top control, front and rear panels

TV top control panel

WEGA GATE

PROG

TV rear panel

(MONO) (MONO)

qsqd

TV front panel

(MONO)

Button/Terminal Function See

1 ! Turn off or turn on the TV. D 2 Remote control sensor. - 3 Wake Up indicator. J 3 1 Standby indicator. D 4 i Headphone jack. - 5 t2 Video input terminal 2. H 6 PROG +/– Select program number. - 7 2 +/– Adjust volume. - 8 t Select TV or video input. H

WEGA GATE menu operations

6,7 V,v,B,b Select and adjust items. K

Confirm selected items. K

8 9 WEGA GATE Display or cancel WEGA GATE menu. K

FM Listen to FM Radio. R

(KV-SW21N63/ SW21N60 only)

SOUND MODE Select sound mode options with a 5-Band Graphic J (KV-SW21N50 only)

Equalizer display.

qa 8 Antenna input terminal. H qs T Monitor output terminal. H qd Component video input terminal. H qf t1 Video input terminal 1. H

qg WOOFER 3D WOOFER terminal. G

(KV-SW21N63 only)

★ The button will be labeled as SOUND MODE for KV-SW21N50 only.

+ 16 hidden pages

Sony WEGA KV-SW21 Operating Instructions Manual

Specifications and Main Features

Frequently Asked Questions

User Manual