Disassemble Instruction
VGN-C Series
VGN-C SERIES
Rev 1.01.101806 SONY CONFIDENTIAL 1
Disassemble Instruction
VGN-C Series – Preliminary Considerations
Safety Precautions
In order to prevent harm to both yourself and the unit, ALWAYS disconnect all peripherals and
cables, and unplug the AC Adapter before performing any repairs on the unit. Shoes with nonconductive rubber soles should be worn to minimize the chance of shock or injury.
ESD Protection
The components of the VGN-C Series are susceptible to damage caused by ESD (electrostatic
discharge). Always follow proper grounding procedures and utilize appropriate equipment such as
a wrist grounding strap and anti-static mat when performing any repairs on the unit. If a properly
grounded wrist strap is not available, touch an unpainted metal surface of the computer chassis to
discharge static electricity. This should be done periodically during the repair to discharge any
static charge that has been accumulated. When removing a component from the system, be sure to
place it on an anti-static mat.
Cosmetic Care
Always protect both the unit and the repair surface from scratches, dings, dents, and other cosmetic
damage by placing a protective mat between the unit and the repair surface. Never place an LCD
face-down on an unprotected surface.
Rev 1.01.101806 SONY CONFIDENTIAL 2
Disassemble Instruction
VGN-C Series – Flow Chart
VGN-CXX
BATTERY
MEMORY
KEYBOARD
PALMREST
POWER
SWITCH BOARD
SPEAKER
TOUCHPAD
CPU FAN
ODD
HDD
HEAT SINK CPU
LCD ASSY BEZEL
BOTTOM
ASSY
WIRELESS
LAN CARD
HINGE L/R
BLUETOOTH
LCD PANEL
PCCARD
BOARD
MIC
INVERTER
FUNCTION
BOARD
ANTENNA
L/R
LCD
HOUSING
BOTTOM
HOUSING
MB
THERMAL
RJ-11/RJ-45 DC JACK
Rev 1.01.101806 SONY CONFIDENTIAL 3
Disassemble Instruction
VGN-C Series - Screws
B2 B3 B4 B5 B7 B8 B10 B6
Station
PC CARD BOARD
MIC BOARD
WLAN ANTENEN L/R
THERMAL MODULE CPU
Screw model
B2
B2
B2
B3
Screw needed for Disassembly
M2*L2.5
M2*L2.5
M2*L2.5
M2*L3
M2*L3
M2*L3
M2*L3
M2*L3
M2*L3
M2*L3
M2*L3
M2*L3
M2*L3
M2*L3.5
Amount
2
2
2
2
2B3MOTHERBOARD
2B3FUNCTION BOARD
2B3DC IN SHIELD
2B3RJ SHIELD
2B3BLUETOOTH ANTENNA
1B3TOUCHPAD GROUND WIRE
4B3SPEAKER
4B3SHELTER PLATE
2B3TOUCHPAD BUTTON
3B4POWER SWITCH BOARD
3M2*L3.5B4PALMREST (ODD)
4M2*L4B5HINGE COVER L/R
2M2*L4B5LCD PANEL
6M2*L4B5HINGE L/R
4M2*L4B5THERMAL FAN
4M2*L4B5THERMAL MODULE CPU
4M2*L4B5LCD BEZEL
Station
THERMAL MODULE VGA
CPU COVER
PALMREST (BOTTOM)
HDD
Screw model
B6
B6
B6
B6
M2*L7
M2*L7
M2*L7
M2*L7
M2*L7
M2*L7
M2*L10
M2*L10
M2*L15
M2*L15
M3*L3
Amount
2
2
8
2
1B6ODD
2B6PALMREST (TOP)
1B7MOTHERBOARD
1B7THERMAL MODULE (MB)
1B8PALMREST
1B8KEYBOARD
6B10ASSY LCD
Rev 1.01.101806 SONY CONFIDENTIAL 4
Disassemble Instruction
VGN-C Series - Battery Removal
1)
OVERVIEW-BACK
LOCK / UNLOCK RELEASE
PRESS THE UNLOCK TAB AND THE RELEASE TAB TOWARDS THE CENTER OF
THE BATTERY. SLIDE THE BATTERY AWAY THE SYSTEM.
Rev 1.01.101806 SONY CONFIDENTIAL 5
Disassemble Instruction
VGC-LS1 Series – Battery Removal
VGN-C Series - Memory Removal
1)
LOOSEN ONE RETAINED SCREW
2)
3)
GENTLY PRESS THE CLIPS AWAY FROM THE MEMORY MODULE AND LIFT
THE MEMORY MODULE FROM THE SYSTEM
4)
ROTATE THE RAM DOOR TOWARDS THE BOTTOM OF THE SYSTEM
REPEAT FOR THE SECOND MEMORY MODULE
Rev 1.01.101806 SONY CONFIDENTIAL 6
Disassemble Instruction
VGN-C Series - CPU Removal
1)
RETAINED
SCREW
B6
REMOVE TWO SCREWS. LOOSEN ONE RETAINED SCREW. ROTATE THE
CPU COVER FROM THE TOP
2)
B5
3)
LIFT THE FAN STRAIGHT UP. ROTATE THE HEATSINK TOWARDS THE EDGE
OF SYSTEM AND REMOVE
4)
FAN CABLE
DISCONNECT THE FAN CABLE. REMOVE FOUR SCREWS FROM THE FAN
AND FOUR SCREWS FROM THE HEAT SINK
UNLOCK THE CPU SOCKET BY ROTATING THE LOCK TO THE LEFT
WITH A FLAT-BLADE SCREWDRIVE. CAREFU LLY LIFT THE CPU UP
Rev 1.01.101806 SONY CONFIDENTIAL 7
Disassemble Instruction
VGN-C Series - ODD Removal
1)
2)
B6
REMOVE ONE SCREW
SLIDE THE OPTICAL DRIVE OUT OF THE SYSTEM
Rev 1.01.101806 SONY CONFIDENTIAL 8
Disassemble Instruction
VGN-C Series – Hard Drive Removal
1)
B6
REMOVE TWO SCREWS
2)
SLIDE THE HDD TOWARDS THE FRONT OF THE SYSTEM AN D REMOVE
Rev 1.01.101806 SONY CONFIDENTIAL 9