Sony UNI-OFL7T2 Specsheet

UNI-OFL7C2 & UNI-OFL7T2

Security Camera Enclosures

Vandal Resistant Outdoor Recessed Dome

The UNI-OFL7C2 & UNI-OFL7T2 are a 7-inch recessed dome enclosures that offer vandal resistance, versatility, easy installation and camera protection in a compact size. These inconspicuous, recessed dome housings are speciﬁcally designed to accommodate the Sony SNC-RZ25N, SNC-RH124, SNC-RS44/46, SNC-RX, SNC-ER/EP and SNC-ZR/ZP series of PTZ cameras.

KEY FEATURES

• Designed for SNC-RZ25N, SNC-RH124, SNC-RS44/46, SNC-RX, SNC-ER/EP and SNC-ZR/ZP series of PTZ cameras.

• Vandal resistant, heavy duty construction, rated to IK10 standards.

• Designed to be water and dust tight to IP66 standards.

• Plenum rated for ﬁre resistant ceiling applications.

• Easy camera installation and servicing from below the ceiling or overhang.

• Includes a decorative trim ring with safety lanyard and captive security fasteners.

• Optically clear 0.118-inches (3mm) thick aspheric polycarbonate dome.

• Thermostatically controlled 24VAC heater.

• 24VAC input with separate power inputs for heater, blower and camera power.

• RoHS, WEEE, UL, CE compliant.

IR Illuminator

(Images 1)

BID SPECIFICATIONS

• The outdoor dome camera housing shall be a Sony model UNI-OFL7C2 and UNI-OFL7T2. The housing shall be designed for the

SNC-RZ25N, SNC-RH124, SNC-RS44/46, SNC-RX, SNC-ER/EP and SNC-ZR/ZP series of PTZ cameras. These models shall also be equipped with 24VAC input blowers and thermostatically controlled heaters. The back box shall be constructed from heavy 10-gauge aluminum and be capable of being installed in its entirety from below the ceiling. The top will measure (H x D) 6.75 x

9.16 inches. The lower dome shall be made of an injection molded, 3mm thick, optically clear thermoplastic polycarbonate (1 F-stop light reduction for tinted lower dome). The lower dome shall be held in place with a die-cast aluminum trim ring (white powder coat ﬁnish) that attaches with a minimum of (3) security fasteners. The UNI-OFL7C2 and UNI-OFL7T2 shall be designed to be installed in either sheetrock or hard ceiling surfaces. Three rotating support arms will allow for adjustment to the ceiling material thickness. The unit shall be fully sealed, designed to meet IP66 dirt/water ingress rating. Unit will include thermostatically controlled 25 watt heater and blower unit. The blower shall draw 1.4W continuous power. The 25W heater shall turn on at 40°F (5°C) and turn off at 60°F (15°C). The housing shall support a temperature range of -20°F (-29°C) to 122°F (50°C).

• Note: To achieve the increased depth with the aspheric design for optimal camera lens to capsule orientation, the capsule is

slightly angled around the highest section. This creates a “line’, visible to the naked eye, around the upper most section of the capsule. This “line” serves as the geometric center line used to insure proper camera placement. It is not typically seen by the camera except when used with cameras that have above the horizon tilt capability.

SPECIFICATIONS

Mechanical

Size (H x W x D) 11.2 x 11.2 11.5 inches (284 x 284 x 292mm) Weight 9 lbs. (4.1 kg) without camera Upper housing 10-gauge aluminum, powdercoated Trim ring Die-cast aluminum, powdercoated Lower dome 0.118-inches (3mm), optically clear, thermoplastic polycarbonate

Environmental

Operating temperature -20°F (-29°C) to 122°F (50°C) Heater activates at 40°F (5°C), deactivates at 60°F (15°C), 24VAC, 25W Blower activates at Continuous operation

Models

UNI-OFL7C2 Outdoor, recessed mount, clear dome enclosure with 24VAC input and heater/blower UNI-OFL7T2 UNI-OFL7C2 with a tinted lower dome

Electrical

Heater and blower 24VAC 27 watts Camera 24VAC 25 watts

Shipping

Weight 10 lbs (4.6 kg) Box dimensions 12 x 12 x 19 inches (305 x 305 x 483mm)

UNI-OFL7C2 & UNI-OFL7T2

SYSTEM CONFIGURATIONS

UNI-OFL7C2

Network

HD monitor

Recording Server NSR-1000 Series

Recording Software

IMZ-NS100 Series

ACCESSORIES

UNI-WMB1

Gooseneck wall bracket

UNI-CMA1

Corner adapter

UNI-PMA1

Pole mount adapter

UNI-WDB3

Wall/pendant adapter bracket for outdoor mini dome cameras

UNI-WMBB1

Aluminum pole/wall mount adapter bracket with straps

UNI-PBU1

Wall/pendant adapter bracket for outdoor mini dome cameras

DIMENSIONS

¾ INCH CONDUIT ENTERANCE

(232.7)

(188.1)

Unit: inches (mm)

9.16

8.00

(203.1)

4.12

(104.6)

½ INCH CONDUIT ENTERANCE

12.11

(307.7)

7.41

11.18

(284)

Sony Electronics Inc. 1 Sony Drive Park Ridge, NJ 07656 sony.com/security

U-OFL7C2

Reproduction in whole or in part without written permission is prohibited.

Features and speciﬁcations are subject to change without notice.

Weights and measurements are approximate.

Sony and the Sony make.believe logo are trademarks of Sony.

Printed in USA (05/12)