Sony UNI-CMA1, UNI-WMB1, UNI-ORS7C1, UNI-OPL7C2, UNI-OPL7T2 Specsheet

Security Camera Housings | Product Guide

click: sony.com/security

NC-RZ25N

S

NC-RZ50N

S

Outdoor housing for SNC RX Series; SNC-RZ25N

NC-RX530N

S

NC-RX550N

S

NC-RX570N

S

NORMAL HOUSING

UNI-ONL7C2 (clear lower dome)

UNI-ONL7T2 (tinted lower dome)

• Outdoor dome, UV protected

• Thermostatically controlled heater

• 24 Hour fan operation for effective heating and

• Optically correct polycarbonate lower dome

• Choice of clear or tinted lower dome

• 24vac input into enclosure, AC 24V feed to camera inside
enclosure provided

• Pendant mount, 11/2” NPT quick connect coupling

• Accepts the SNC-RX530N, SNC-RX550N, SNC-RX570N and
SNC-RZ25N cameras

condensation protection

PRESSURIZED HOUSING

UNI-OPL7C2 (clear)

UNI-OPL7T2 (tinted)

• Pressurized outdoor dome, UV protected

• Eliminates condensation, bugs and other debris

• Great corrosion protection, perfect for coastlines,

• 5-7 psi pressure relief valve

• IP67

• Thermostatically controlled heaters

• 24 Hour fan operation for effective heating and
condensation protection

• Optically correct polycarbonate, clear or tinted lower dome

• 24vac input via multi-pin connector

• Pendant mount, 11/2” NPT quick connect coupling

• Accepts the SNC-RX530N, SNC-RX550N, SNC-RX570N and
SNC-RZ25N cameras

and other extreme environmental conditions

VANDAL RESISTANT HOUSING

UNI-ORL7C2 (clear) • UNI-ORL7T2 (tinted)

• Outdoor dome, UV protected
Strong cast aluminum top and trim ring

•
Rugged polycarbonate lower dome

•

• Thermostatically controlled heaters
24 Hour fan operation for effective heating and

•
condensation protection
Optically correct, clear or tinted lower dome

•
24vac input into enclosure,AC 24V feed to camera inside enclosure provided

•

• Pendant mount, 11/2” NPT quick connect coupling
Accepts the SNC-RX530N, SNC-RX550N, SNC-RX570N and

•
SNC-RZ25N cameras

WIRELESS READY – Normal Housing

UNI-ONL7C2W (clear) • UNI-ONL7T2W (tinted)

• Outdoor dome, UV protected

• Wireless antenna cable included with housing, female
N-connector on dome, cable with MMCX connector in
enclosure to connect directly to optional SNCA-CFW1

• To be used with SNCA-CFW1 wireless card. (Purchased
separately) – 2 foot cable with N-connectors included.
SNCA-AN1 antenna or user provided antenna may be used.
(Purchased separately)

• Thermostatically controlled heater

• 24 Hour fan operation for effective heating and condensation protection

• Optically correct polycarbonate lower dome

• Choice of clear or tinted lower dome

• 24vac input into enclosure,AC 24V feed to camera inside enclosure provided

• Pendant mount, 11/2” NPT quick connect coupling

• Accepts the SNC-RX530N, SNC-RX550N, SNC-RX570N and
SNC-RZ25N cameras

WIRELESS READY
Vandal Resistant Housing

UNI-ORL7C2W (clear lower dome)
UNI-ORL7T2W (tinted lower dome)

• Outdoor dome, UV protected

• Wireless antenna cable included with housing, female
N-connector on dome, cable with MMCX connector in
enclosure to connect directly to optional SNCA-CFW1

• To be used with SNCA-CFW1 wireless card. (Purchased separately) –
2 foot cable with N-connectors included. SNCA-AN1 antenna or
user provided antenna may be used.

• Strong cast aluminum top and trim ring

• Rugged polycarbonate lower dome

• Thermostatically controlled heaters

• 24 Hour fan operation for effective heating and condensation protection

• Optically correct, clear or tinted lower dome

• 24vac input into enclosure, AC 24V feed to camera inside
enclosure provided

• Pendant mount, 11/2” NPT quick connect coupling

• Accepts the SNC-RX530N, SNC-RX550N, SNC-RX570N and
SNC-RZ25N cameras

Outdoor housing for SNC-RZ50N; SNC-RZ30N

SNC-RZ30N

NORMAL HOUSING

UNI-ONS7C1 (clear lower dome)

UNI-ONS7T1 (tinted lower dome)

Outdoor dome, UV protected

•

• Thermostatically controlled heater

• 24 Hour fan operation for effective heating
and condensation protection

• Choice of clear or tinted lower dome

• Includes internal power supply, for 12vdc camera power

• 24vac input to enclosure

• DC 12V with pre-terminated cable/plug for camera

• Pendant mount, 11/2” NPT quick connect coupling

• Accepts the SNC-RZ50N and SNC-RZ30N cameras

• Optically correct polycarbonate lower dome

inside enclosure

VANDAL RESISTANT HOUSING

UNI-ORS7C1 (clear)

UNI-ORS7T1 (tinted)

• Outdoor dome, UV protected

• Strong cast aluminum top and trim ring

• Rugged polycarbonate lower dome

• 24 Hour fan operation for effective heating and
condensation protection

• Optically correct, clear or tinted lower dome

• 24vac input into enclosure

• DC 12V with pre-terminated cable/plug for camera
inside enclosure

• Includes internal power supply, for 12vdc camera power

• Pendant mount, 11/2” NPT quick connect coupling

• Accepts the SNC-RZ50N and SNC-RZ30N cameras

• Thermostatically controlled heaters

NORMAL HOUSING

SNCA-HP5

• Outdoor Housing for SNC-P5

• Wall and Ceiling Mountable

• For use with SNC-P5

PRESSURIZED HOUSING

UNI-OPS7C1 (clear) • UNI-OPS7T1 (tinted)

• Pressurized outdoor dome, UV protected
Eliminates condensation, bugs and other debris

•

• Great corrosion protection, prefect for coastlines, and other
extreme environmental conditions
5-7 psi pressure relief valve

•

• IP67
Thermostatically controlled heaters

•

• 24 Hour fan operation for effective heating and condensation protection
Optically correct polycarbonate, clear or tinted lower dome

•
24vac input via multi-pin connector

•

• DC 12V with pre-terminated cable/plug for camera inside enclosure
Includes internal power supply, for 12vdc camera power

•

• Pendant mount, 11/2” NPT quick connect coupling

• Accepts the SNC-RZ50N and SNC-RZ30N cameras

WIRELESS READY – Normal Housing

UNI-ONS7C1W (clear) • UNI-ONS7T1W (tinted)

• Outdoor dome, UV protected

• Wireless antenna cable include with housing, female N-connector
on dome, cable with MMCX connector in enclosure to connect
directly to optional SNCA-CFW1

• To be used with SNCA-CFW1 wireless card. (Purchased separately) –
2 foot cable with N-connectors included. SNCA-AN1 antenna or user
provided antenna may be used. (Purchased separately)

• Thermostatically controlled heater

• 24 Hour fan operation for effective heating and condensation protection

• Optically correct polycarbonate lower dome

• Choice of clear or tinted lower dome

• 24vac input into enclosure

• DC 12V with pre-terminated cable/plug for camera inside enclosure

• Includes internal power supply, for 12vdc camera power

• Pendant mount, 11/2” NPT quick connect coupling

• Accepts the SNC-RZ50N camera

WIRELESS READY – Vandal Resistant Housing

UNI-ORS7C1W (clear lower dome)
UNI-ORS7T1W (tinted lower dome)

• Outdoor dome, UV protected

• Wireless antenna cable include with housing, female N-connector on
dome, cable with MMCX connector in enclosure to connect directly
to optional SNCA-CFW1 wireless card (Purchased separately)

• To be used with SNCA-CFW1 wireless card.(Purchased separately) – 2 foot cable with
N-connectors included. SNCA-AN1 antenna or user provided antenna may be used.

• Does not include antenna mount

• Strong cast aluminum top and trim ring

• Rugged polycarbonate lower dome

• Thermostatically controlled heaters

• 24 Hour fan operation for effective heating and condensation protection

• Optically correct, clear or tinted lower dome

• 24vac input into enclosure

• DC 12V with pre-terminated cable/plug for camera inside enclosure

• Includes internal power supply, for 12vdc camera power

• Pendant mount, 11/2” NPT quick connect coupling

• Accepts the SNC-RZ50N camera

2 3

NC-RZ25N

S

NC-RZ50N

S

Indoor housing SNC RX Series; SNC-RZ25N

SNC-RX530N

NC-RX550N

S

SNC-RX570N

NORMAL HOUSING

UNI-INL7C2 (clear lower dome)
UNI-INL7T2 (tinted lower dome)

• Indoor dome

• Optically correct polycarbonate lower dome

• Choice of clear or tinted lower dome

• No electronics. User provides AC 24V feeds to camera/enclosure

• Pendant mount, 11/2” NPT quick connect coupling

• Accepts the SNC-RX530N, SNC-RX550N, SNC-RX570N and
SNC-RZ25N cameras

Indoor housing for SNC-RZ50N; SNC-RZ30N

NC-RZ30N

S

NORMAL HOUSING

UNI-INS7C3 (clear lower dome)
UNI-INS7T3 (tinted lower dome)

• Indoor dome

• Optically correct polycarbonate lower dome

• Choice of clear or tinted lower dome

• No electronics.User provides power feed
to camera/enclosure

• Pendant mount, 11/2” NPT quick connect coupling

• Accepts the SNC-RZ50N and SNC-RZ30N cameras

NORMAL HOUSING

UNI-INS7C1 (clear lower dome)
UNI-INS7T1 (tinted lower dome)

UNI-INS7C3 (clear lower dome)

• Indoor dome

• Optically correct polycarbonate lower dome

• Choice of clear or tinted lower dome

• AC 24V input into enclosure, DC12V camera power
and plug provided inside enclosure

• Pendant mount, 11/2” NPT quick connect coupling

• Accepts the SNC-RZ50N and SNC-RZ30N cameras

VANDAL RESISTANT HOUSING

UNI-IRL7C2 (clear)
UNI-IRL7T2 (tinted)

• Indoor dome

• Strong cast aluminum top and trim ring

• Rugged polycarbonate lower dome

• Optically correct, clear or tinted lower dome

• No electronics. User provides AC 24V feeds to
camera/enclosure

• Pendant mount, 11/2” NPT quick connect coupling

• Accepts the SNC-RX530N, SNC-RX550N, SNC-RX570N and
SNC-RZ25N cameras

VANDAL RESISTANT HOUSING

UNI-IRS7C3 (clear)
UNI-IRS7T3 (tinted)

• Indoor dome

• Strong cast aluminum top and trim ring

• Rugged polycarbonate lower dome

• Optically correct, clear or tinted lower dome

• No electronics.User provides power feed to
camera/enclosure

• Pendant mount, 11/2” NPT quick connect coupling

• Accepts the SNC-RZ50N and SNC-RZ30N cameras

VANDAL RESISTANT HOUSING

UNI-IRS7C1 (clear)
UNI-IRS7T1 (tinted)
UNI-INS7T3 (tinted)

• Indoor dome

• Strong cast aluminum top and trim ring

• Rugged polycarbonate lower dome

• Optically correct, clear or tinted lower dome

• AC 24V input into enclosure, DC12V camera power
and plug provided inside enclosure

• Pendant mount, 11/2” NPT quick connect coupling

• Accepts the SNC-RZ50N and SNC-RZ30N cameras

4

5

Recessed Ceiling Housing for Sony’s SNC-RX series

Recessed Ceiling Housings for Fixed Cameras SNC-CS50N,

and SNC-RZ series camera.

UNI-ID7C3

• 7” diameter dome indoor recessed ceiling housing

• Clear lower dome

• White Trim Ring

• Interface Wiring
Plenum rated metal top

•

SNC-RZ25NSNC-RZ30N

NC-RZ50N

S

UNI-ID7T3
(Tinted Indoor Housing)

7" diameter dome indoor recessed ceiling housing

•
Tinted lower dome

•
White trim ring

•

• No electronics. Interface wiring
Ethernet sensor I/O, power provided by user

•
Plenum rated metal top

•

• Light Loss is 1.2 F-Stop maximum

Indoor Recessed Plenum Ready Housing for SNC-DS10,
SNC-DM110, SNC-DF50N

NC-RX530N

S

SNC-RX550N

NC-RX570N

S

SNC-Z20N, SNC-CS11, SNC-CS10, SNC-CM120 and SNC-CS20

UNI-IFF7C3

7” diameter dome indoor recessed

•
eiling housing

c

• Clear lower dome

White trim ring

NC-CS50N

S

SNC-Z20N

SNC-CS11

•

• No electronics. Interface wiring (ethernet,

ensor I/O, power provided by user)

s
Plenum rated metal top

•

UNI-IFF7T3

7” diameter dome indoor recessed ceiling housing

•

SNC-CS10

NC-CM120

S

NC-CS20

S

• Tinted lower dome

White trim ring

•

• No electronics. Interface wiring (ethernet, sensor I/O,
ower provided by user)

p

• Plenum rated metal top

• Light loss is 1.2 F-Stop maximum

Pendant Mount Mini Dome Brackets

UNI-ILD3C3

• Plenum ready metal top

• Easy installation

• Provisioned for ¾” conduit pipe

• Small profile

• UL listed
SNC-DS10

SNC-DF50NSNC-DM110

Housings for the SNC-CS10, SNC-CS11,SNC-CS50N, SNC-Z20N,
SNC-CM120 and SNC-CS20

-SNC-UNIHB/1

(Outdoor wall mount housing with heater and blower)

• Extruded aluminum housing

• Tamper resistant camera housing lock down screws provided

• High strength steel wall mount bracket included

• Outdoor models include AC 24V heater and blower

SNC-UNI
(Indoor wall mount housing without heater/blower)

• Extruded aluminum housing

• Tamper resistant camera housing lock down screws provided

• High strength steel wall mount bracket included

SNC-CS11 SNC-CS50N

SNC-CM120

SNC-CS20

SNC-Z20N

SNC-DF85N

UNI-MDB2

• Wall mount or pendant mount for the
SNC-DF85N, SNCDF80N,SSC-CD75 and SSC-CD77

• All aluminum construction

• 1” pipe thread for pendant mounting

• Gooseneck bracket for wall mounting

• Indoor or outdoor use

Power Block Unit

UNI-PBU1

• 220V/110Vac input, 84va capacity

• Rugged outdoor NEMA box

• 24vac output for camera, heater and blower

• Fused protected output

• Hinged door for easy access

• UNI-MDB2 and UNI-MDB3 mounts directly to the hinged access panel

SSC-CD77SSC-CD75SNC-DF80N

SNC-DM160

SNC-DS60

UNI-MDB3

• Pendant Mount for the SNC-DM160/
SNC-DS60 Megapixel Cameras

• All aluminum construction

• Indoor or outdoor use

6

7

Mounting Accessories

UNI-WMB1

Gooseneck
Wall Mount

UNI-WMB1 Wall Mount

Mounting Accessories Needed:

UNI-WMB1 – Gooseneck Wall Mount

•

• Outdoor Pendant Housing

UNI-RMB1

Aluminum
Parapet Mount

UNI-PMA1

Aluminum Existing
Pole Mount Adaptor

UNI-CMA1

Aluminum Corner
Mount Adaptor

UNI-PMA1 Pole Mount

Mounting Accessories Needed:

UNI-WMB1 – Gooseneck

•
Wall Mount

• UNI-PMA1 – Aluminum

xisting Pole Mount

E

daptor

A

• Outdoor Pendant Housing

UNI-PBU1

Power Block Unit

UNI-RD7C

Clear replacement
capsule for 7” dome
cameras

YT-ICB45

• In-Ceiling Mount Kit for SSC-CD79,
NC-DF50N,and SNC-DF85N.

S

YT-ICB73V

• Flush Mount Kit for SSC-CD73V

UNI-RD7T

Tinted replacement
capsule for 7”
dome cameras

Adaptors

SW-170A

Y
(Single camera Power

over coax adaptor)

• Video Output BNC x 8
omposite video

c

Video Input Camera In, BNC x 4

•

•External Sync VS or VD-w

•Internal Sync MPX-VS or
PX-VD-W

M
Maximum Cable Length - 300m

•

sing RG-59B/U

u
500m using RG-6A/U

•

600m using RG-11A/U

•

YSW-270A
(4 camera power over

coax adaptor)

• Video Output - BNCx2

composite video

• Video Input - Camera In,

BNC x 1

• External Sync VS or VD-W

• Maximum Cable length - 300m

using RG-59B/U

• 500m using RG-6A/U

• 600m using RG-11A/U

• Cable compensation -

3 position

Cable Compensation -

•
3 position

Power Requirements -

•
AC 120V, 60Hz

•Power Consumption 92W

•Weight - 8lb. 6 oz. (3.8kg)
Dimensions - 424 x 52 x 345 mm

•
Operating Temperature -

•
14°F to 122°F (10 to 50°C)

• Power requirements -

AC12oV, 60 Hz

• Power Consumption 27W

• Weight - 4 lb. 3 oz. (1.9 kg)

• Operating Temperature -

14°F to 122°F (10 to 50°C)

• Dimensions 212 x 52 x 345 mm

UNI-RMB1

Roof Mount (Parapet)

Mounting Accessories Needed:

• UNI-RMB1 –Aluminum Parapet Mount

• Outdoor Pendant Housing

UNI-CMA1 Corner Mount

Mounting Accessories Needed:

• UNI-CMA1 – Aluminum Corner Mount Adaptor

• UNI-WMB1 – Gooseneck Wall Mount

• Outdoor Pendant Housing

UNI-PBU1

Power Block Unit (Wall Mount)

Mounting Accessories Needed:

• UNI-WMB1 – Gooseneck Wall Mount

UNI-PBU1

Power Block Unit (Pole Mount)

Mounting Accessories Needed:

• UNI-PMA1 – Aluminum
Existing Pole Mount
Adaptor

• UNI-WMB1 –
Gooseneck Wall
Mount

8

9

Pendant Dome Housing Model Naming Convention

ressurized

P

C for clear
T for tinted

1 for DC12V
2 for AC24V
3 for no interface wiring

r electronics

o

ormal

N

UNI-INS7C3

UNI-INS7T3

Housing with Wall Bracket

SNC-CS50N, SNC-Z20N,SNC-CS10,
SNC-CS11,SNC-CM120,SNC-CS20

Outdoor Indoor (no heater/blower)

SNC-UNIHB/1 SNC-UNI

I for indoor
O for outdoor

UNI -

N for normal type
R for vandal resistant
P for pressurized

L for Long – RX550N,RZ25N
S for Short – RZ30N,RZ50N

XXX 7 XXX

7”diameter dome

Example: UNI-ONL7C2

utdoor (with heater/blower),normal type,for RZ25N, RX530N,RX550N or RX570N,7” diameter, clear dome,AC24V feed

O

Housing Selection Guide

SNC RX Series / SNC-RZ25N SNC-RZ50N / SNC-RZ30N

Outdoor

oom network camera, pendant

z
mount type, w/ heater & blower.
AC 24V interface,AC 24V power
supply NOT included.

Wireless Ready Outdoor

ousings for pendant mount type,

h
w/ heater & blower.Prewired
internally for use with SNCA-CFW1.
Dome has N-type connector
interface on the top to accept
external antenna. External antenna &

WIRELESS

mount NOT included. AC 24V feed,
AC 24V power supply NOT included.

Indoor Long

pan/tilt/zoom network camera,
pendant mount type, no heater/
blower or interface wiring included.

Indoor Short

mount type, no heater/blower,
internal AC 24V to DC-12V for
camera feed,AC 24V external
interface wiring included, AC 24V
power supply NOT included.

ousing for pan/tilt/

h

housing for

housing, pendant

Clear Dome

Tinted Dome

Clear Dome

Tinted Dome

Clear Dome

Tinted Dome

Clear Dome

Tinted Dome

ormal

N

UNI-ONL7C2 UNI-ORL7C2 UNI-OPL7C2 UNI-ONS7C1 UNI-ORS7C1 UNI-OPS7C1

UNI-ONL7T2 UNI-ORL7T2 UNI-OPL7T2 UNI-ONS7T1 UNI-ORS7T1 UNI-OPS7T1

UNI-ONL7C2W UNI-ORL7C2W – UNI-ONS7C1W UNI-ORS7C1W –

UNI-ONL7T2W UNI-ORL7T2W – UNI-ONS7T1W UNI-ORS7T1W –

UNI-INL7C2 UNI-IRL7C2 – – – –

UNI-INL7T2 UNI-IRL7T2 – – – –

–

–

andal Resistant

V

– – UNI-INS7C1

– – UNI-INS7T1

Recessed Ceiling Housing

SNC RX Series, SNC-RZ50N,SNC-RZ25N,SNC-RZ30N, SNC-RZ50N

Clear Tinted

SNC ID7C1 SNC-ID7T1

Recessed Ceiling Housing for Fixed Cameras

SNC-CS50N, SNC-Z20N,SNC-CS11,SNC-CS10, SNC-CM120,SNC-CS20

Clear Tinted

UNI-IFF7C3 UNI-IFF7T3

W for wireless

andal Resistant

V

UNI-RS7C1 –

UNI-RS7T1 –

ressurized

P

Architectural / Engineering Specifications

U

NI-PBU1 Bid Specifications

The power box shall be a Sony Model UNI-PBU1 or equivalent.The power input shall be a 120vac or 220vac and the output 24vac, rated at 84va (watts).The product includes PTC fuses
for the camera power and another one for the heater/blower power. It shall be designed to support one outdoor Sony housing with heaters, blowers and camera.The body of the unit
shall be cast aluminum with white power coat finish.(2) ¾” conduit inputs located at the bottom of the box to provide input for power and for data cabling.The unit shall be designed for
outdoor locations, with an IP 66 rating. Clips shall be provided to allow it to be mounted to the pole mount adapter UNI-PMA1,or the corner mount adapter,UNI-CMA1. Mechanical
Specifications: Dimensions – 7.9” (w) x 8.8” (h) x 3.8”(d). Weight – 9 lbs.Construction – Cast Aluminum.

UNI-MDB2/3 Bid Specifications

The wall/pendant mount adaptor shall be a Sony model UNI-MDB2,UNI-MDB3 or equivalent.The UNI-MDB2 shall support the SNC-DF80N, SNC-DF85N,SSC-CD77 and SSC-CD75 cameras.
The UNI-MDB3 shall support the SNC-DM160 and SNC-DS60. The cast aluminum top cover shall have screw taps to allow the cameras to be mounted directly, and provide a 1” NPT pipe
t

hread for mounting to a pipe or to the included wall mount bracket.The wall mount is also constructed from aluminum.The kit shall allow the camera to be mounted down from the ceil­ing using a 1” threaded pipe (not provided) or to be mounted to an interior or exterior wall.The bracket features a light gray finish.The wall mount can be combined with the UNI-CMA1
for corner mount applications and with the UNI-PMA1 for pole mount applications.The kit shall include gaskets and Teflon tape for water ingress protection outdoors. Mechanical
Specifications: UNI-MDB2 Dimensions - 7.28” diameter x 2.78”UNI-MDB3 Dimensions - 6.82”diameter x 2.83”Weight – UNI-MDB2 and UNI-MDB3 – 2 lbs.; gooseneck bracket – 0.9 lb

UNI-IFF7 Recessed Series Bid Specifications

The recessed ceiling housing designed & engineered for Sony’s fixed cameras (SNC-CS50N, SNC-Z20N, SNC-CS20, SNC-CS11 and SNC-CS10) shall be the Model UNI-IFF7C3 and UNI-IFF7T3
o

r equivalent.The back box shall be constructed from 18 and 20-gauge steel and be capable of being installed in its entirety from below the ceiling.The steel top shall measure 5.5”
(h) x 11” (d).The lower injection molded polycarbonate dome shall be available in clear or tinted material.The UNI-IFF7T3 shall include a tinted lower dome and the UNI-IFF7C3, a clear
l

ower dome.The lower dome shall be made from injection molded polycarbonate,and held in place by a 19-gauge steel trim ring with a white powdercoat finish.The product shall be
designed to be installed in either sheetrock or drop ceilings.Three rotating support arms shall allow for adjustment to the ceiling material thickness. Mechanical Specifications (all
m

odels): Dimensions –12” (w) x 9.1” (h) x 12” (d).Weight – approx. 9 lbs. (without camera).

U

NI-ID7 Recessed Series Bid Specifications

The recessed ceiling housing shall be for Sony’s Pan/Tilt/Zoom camera models, SNC-RX series, SNC-RZ25N,SNC-RZ50N and the SNC-RZ30N.The UNI-ID7C3 shall include a clear lower
dome and the UNI-ID7T3 shall include a tinted lower dome.The back box shall be constructed from 18 and 20-gauge steel and be capable of being installed in its entirety from below
the ceiling.The steel top shall measure 5.5” (h) x 11” (d). The lower dome shall be made from injection molded polycarbonate,and held in place by a 19-gauge steel trim ring with a
white powdercoat finish.The product shall be designed to be installed in either sheetrock or drop ceilings.Three rotating support arms shall allow for adjustment to the ceiling material
thickness. Mechanical Specifications (all models): Dimensions –12”(w) x 9.1” (h) x 12” (d). Weight – approx 9 lbs. (without camera).

SNC-UNI Series Bid Specifications

The SNCUNIHB/1 & SNCUNI environmental housings shall be constructed from two extruded aluminum (.08”wall thickness, white finish) halves and two injection molded polycarbonate
end caps. A clear polycarbonate viewing window shall be ultrasonically welded to the inside of the front end cap, creating a watertight seal.The top of the housing shall be hinged from
t

he side to allow accessibility to the camera by one screw in each end cap.Camera adjustment or removal shall be provided via one screw located in the key hole slot on the alu­minum camera sled. Maximum camera/lens combined length shall not exceed 10-1/2 inches. A 25 VA heater is mounted to the inside of the bottom extrusion, directly behind the view­ing window, for defogging and deicing on the SNCUNIHB/1 model. Four vent plugs (2 in front, 2 in rear) will create a positive airflow (front to rear) when the blower is in use (SNCUNIHB/1
model).Two watertight strain relief plugs will be located at the rear of the housing for separate communication wiring and power cable entry. Mechanical Specifcations: Dimensions –

5.7”(w) x 5.4”(h) x 15.25”(d) including protruding parts,not including wall mount bracket.Weight: approx 8 pounds (without camera,with heater and blower).

Standard Indoor and Outdoor housings,“N”Type

The outdoor dome camera housing shall be a Sony Model UNI-ONL7C2,UNI-ONL7C2W, UNI-ONS7C1,UNI-ONS7C1W or equivalent.The indoor models shall be a Sony Model UNI-INL7C2,
UNI-INS7C1,UNI-INS7C3 or equivalent.The UNI-ONL7C2, UNI-ONL7C2W, and UNI-INL7C2 housings shall be designed for the SNC-RX series and SNC-RZ25N cameras.The UNI-ONS7C1, UNI­ONS7C1W,UNI-INS7C1 and UNI-INS7C3 housings shall be designed for the SNC-RZ50 and SNC-RZ30 cameras.The product shall come standard with a pendant mount.The products hous­ing shall be manufactured from a high-impact engineered plastic,UV protected, with a UL flame rating of 94V0.The dome shall be made of an injection molded,optically clear,polycar­bonate blend material.The dome shall be held in place with minimum of (3) fasteners,and a safety cable shall be provided to hold the dome while servicing.Access to the enclosure
shall be from below with (3) captive fasteners used to press the dome against a sealing O-ring. A twist-off feature shall allow for the final removal of the dome.The wiring enters through
the top of the housing on all models.The engineered plastic top, with its reflective white paint,insulates internal equipment.A wall mount bracket, Sony model UNI-WMB1, shall be avail­able as an option.The outdoor models shall also be equipped with 24vac input blower and thermostatically controlled heater.The blower shall draw 1W continuous power.The 25W
heater shall turn on at 60°F (15°C) and turn off at 80°F (25°C).The housing shall support a temperature range of -20°F (-29°C) to 122°F (50°C). UNI-ONS7C1,UNI-ONS7C1W and UNI-INS7C1
will include a 24vac to 12vdc power supply built into the housing.The UNI-INS7C3 shall not include any electronics,and installer provided 12vdc power, must be supplied to the housing.
UNI-ONL7C2W and UNI-ONS7C1W are wireless ready dome housings.The product shall have a pre-installed wireless antenna cable with an MMCX connector for the optional wireless LAN
card,and an N type connector on the enclosure top, for an external antenna. Outdoor Tinted models shall be Model UNI-ONL7T2,UNI-ONL7T2W, UNI-ONS7T1, UNI-ONS7T1W. Indoor tinted
models shall be UNI-INL7T2,UNI-INS7T1, UNI-INS7T3. Mechanical Specifications:UNI-ONL models – Dimensions : 10.3”(D) x 10.3” (w) x 14.6” (H). Weight- 7 Lbs (without camera). UNI-ONS
models - Dimensions : 10.3” (D) x 10.3” (w) x 13.3”(H). Weight- 7 Lbs (without camera).

Vandal Resistant Indoor and Outdoor housings,“R”Type

The vandal resistant outdoor dome camera housing shall be a Sony Model UNI-ORL7C2, UNI-ORL7C2W, UNI-ORS7C1,UNI-ORS7C1W or equivalent.The indoor models shall be a Sony
Model UNI-IRL7C2, UNI-IRL7C3 or equivalent.The UNI-ORL7C2,UNI-ORL7C2W,and UNI-IRL7C2 housings shall be designed for the SNC-RX series and SNC-RZ25N cameras.The UNI-ORS7C1,
UNI-ORS7C1W, and UNI-IRS7C3 housings shall be designed for the SNC-RZ50 and SNC-RZ30 cameras.The product shall come standard with a pendant mount.The housing top and pen­dant mount bracket shall be manufactured from durable cast aluminum.The dome shall be made of an injection molded,optically clear,polycarbonate blend material.The dome shall
be held in place with minimum of (3) fasteners,and a safety cable shall be provided to hold the dome while servicing.Access to the enclosure shall be from below with (3) captive fas­teners. A twist-off feature shall allow for the final removal of the dome.The wiring enters through the top of the housing on all models.A wall mount bracket,Sony model UNI-WMB1,shall
be available as an option.The outdoor models shall also be equipped with 24vac input blowers and thermostatically controlled heaters.The blower shall draw 2W continuous power.The
50W heaters shall turn on at 60°F (15°C) and turn off at 80°F (25°C).The housing shall support a temperature range of -20°F (-29°C) to 122°F (50°C).The UNI-ORS7C1 and UNI-ORS7C1W
will include a 24vac to 12vdc power supply built into the housing. The UNI-IRS7C3 shall not include any electronics,and an installer provided 12vdc power, must be supplied to the hous­ing. UNI-ONL7C2W and UNI-ONS7C1W are wireless ready dome housings.The product shall have a pre-installed wireless antenna cable.The product shall have a pre-installed wireless
antenna cable with an MMCX connector for the optional wireless card,and an N type connector on the enclosure top, for an external antenna. Outdoor Tinted lower dome models shall
be the UNI-ORL7T2,UNI-ORL7T2W,UNI-ORS7T1, UNI-ORS7T1W. Indoor tinted models shall be the UNI-IRL7T2,UNI-IRL7T3. Mechanical Specifications:UNI-ORL models – Dimensions: 10.3” (D) x

10.3”(w) x 14.6” (H). Weight- 7 Lbs (without camera). UNI-ORS models – Dimensions: 10.3” (D) x 10.3”(w) x 13.3” (H). Weight- 7 Lbs (without camera).

Pressurized Outdoor housings,“P”Type

The pressurized outdoor dome camera housing shall be a Sony Model UNI-OPL7C2, UNI-OPS7C1 or equivalent.The UNI-OPL7C2 housing shall be designed for the SNC-RX series and SNC­RZ25N cameras.The UNI-OPS7C1 housing shall be designed for the SNC-RZ50 and SNC-RZ30 cameras.The product shall come standard with a pendant mount.The housing shall be man­ufactured from a high-impact engineered plastic, UV protected,with a UL flame rating of 94V0.The dome shall be made of an injection molded,optically clear, polycarbonate blend
material, and shall be held in place with (9) captive fasteners,used to press the dome against the sealing O-ring.A secondary O-ring seal shall be provided at the top of the enclosure
through a precision machined bracket.This machined bracket shall also be provided with a 5 to 7 psi pressure-relief valve and a standard bore thread dill valve to insert inert dry nitro­gen into the enclosure.All incoming wires will enter the unit via a 10-pin hermetically sealed connector.Access to the enclosure shall be from below with (9) captive fasteners used to
press the dome against a sealing O-ring. A twist-off feature shall allow for the final removal of the dome.The wiring enters through the top of the housing on all models. The engineered
plastic top,with its reflective white paint, insulates internal equipment.A wall mount bracket,Sony model UNI-WMB1,shall be available as an option.The housing shall be equipped with
24VAC input blowers and thermostatically controlled heaters.The blowers shall draw 2W continuous power. UNI-OPS7C1 shall include a 24vac to 12vdc power supply built into the hous­ing. The 50W heater shall turn on at 60°F (15°C) and turn off at 80°F (25°C). The housing shall support a temperature range of -40°F (-40°C) to 122°F (50°C). Tinted lower dome models
shall be UNI-OPL7T2, UNI-OPS7T1. Mechanical Specifications:“P”type models- 14.4” (H) x 11.2” (w) x 11.2” (D). Weight- 8 Lbs (without camera).

10

11

Wireless LAN Cards

SNCA-CFW1
Wireless LAN Card for the following models:

SNC-CS50N, SNC-P5, SNC-RX530N, SNC-RX550N, SNC-RX570N, SNC-RZ25N

•
IEEE 802.11b compliant

•

SNCA-CFW5
Wireless LAN Card for the following models:

SNC-CS50N, SNC-RX530N, SNC-RH124, SNC-RH164, SNC-RS44N, SNC-RS46N, SNC-RS84N,

•
SNC-RS86N, SNC-RX550N, SNC-RX570N, SNC-RZ50N

• IEEE802.11g/11b compliant

SNCA-AN1
External Antenna

• For use with the SNCA-CFW1 or the SNCA-DFW5 Wireless LAN Cards

Sony Electronics Inc.
1 Sony Drive
Park Ridge, NJ 07656

click: sony.com/security

S-HOUSING-C

Reproduction in part or in whole without prior written permission is prohibited.

Features and specifications are subject to change without notice.

All non-metric weights and measurements are approximate.

©2009 Sony Electronics Inc. All rights reserved.

Sony and IPELA are trademarks of Sony.

Printed in USA (8/09)