![](/html/a7/a784/a7840946dcb49c0c6d53c4b51a1bdc44ec5d8c7fa17bd088952afab8aec37409/bg1.png)
UNI-ID7C3 & UNI-ID7T3
Security Camera Enclosures
Recessed Ceiling Housings
The UNI-ID7C3 (clear dome) and UNI-ID7T3 (tinted
dome) are low profile indoor ceiling housings. They
feature a 7-inch optically transparent polycarbonate
dome to accommodate a Sony PTZ camera. The upper
body is made of steel with a white powdercoat trim ring
and an injection molded 3mm thick dome, giving the
housing a clean look.
KEY FEATURES
• Designed for the Sony SNC-RZ25N, SNC-RZ50N, SNC-RS44/46, SNC-RH124,
SNC-RX series PTZ, SNC-ER/EP 520, 550, 580 and SNC-ZR/ZP550 cameras.
• 7-inch dome for easy installation and servicing from below ceiling.
• Housing extends only 3.5 inches below ceiling.
• Includes a decorative trim ring with quick-release pressure springs.
• UL rated for drop ceiling applications.
• Optically transparent .115 inches (3mm) thick aspheric polycarbonate dome.
• Available with a clear (UNI-ID7C3) or tinted (UNI-ID7T3) lower dome.
IR Illuminator
(Images 1)
BID SPECIFICATIONS
• The recessed ceiling housing shall be a Sony model UNI - ID7C3 or UNI - ID7T3. The housings have been designed and
engineered for Sony SNC-RZ25, SNC-RZ50, SNC-RH124, SNC-RS44/46 and the SNC-RX series PTZ, SNC-ER/EP 520, 550, 580
and SNC-ZR/ZP550 cameras. The back box shall be constructed from 18-and 20-gauge steel and capable of being
installed in its entirety from below the ceiling. The steel top will measure 5.5 x 11 inches (H x D). The dome shall be made
of an injection molded, 3mm thick, optically transparent thermoplastic polycarbonate and shall be available in clear or
tinted. The UNI - ID7T3 includes a tinted lower dome and the UNI - ID7C3 includes a clear lower dome. The lower dome shall
be held in place by a 19-gauge steel trim ring (white powdercoat finish). The product shall be designed to be installed in
either sheetrock or drop ceilings. Three rotating support arms will allow for adjustment to the ceiling material thickness.
• Note: To achieve the increased depth with the aspheric design for optimal camera lens to capsule orientation, the
capsule is slightly angled around the highest section. This creates a “line”, visible to the naked eye, around the upper
most section of the capsule. This “line” serves as the geometric center line used to insure proper camera placement. It is
not typically seen by the camera. However, the Sony RH,RS, RX and ER/EP series of cameras have a 15° tilt. The Sony RZ
series of PTZ cameras are capable of a 25° tilt above horizon.
![](/html/a7/a784/a7840946dcb49c0c6d53c4b51a1bdc44ec5d8c7fa17bd088952afab8aec37409/bg2.png)
SPECIFICATIONS
Mechanical
Size (H x W x D) 11.08 x 12.25 x 12.25 inches (281.4 x 311.2 x 311.2mm)
Weight 6 lbs. (3 kg) without camera
Shipping
Weight 10 lbs. (4.6 kg)
Boxing 15 x 15 x 12 inches (381 x 381 x 305mm)
Construction
Body Steel
Back box 18-and 20-gauge steel
Trim ring 19-gauge steel
Dome OptiClear™ polycarbonate
Electrical
No electronics. Interface wiring Ethernet, sensor I/O, power provided by user
UNI-ID7C3 & UNI-ID7T3
SYSTEM CONFIGURATIONS
UNI-ID7C3
UNI-ID7T3
Network
HD monitor
Recording Server
NSR-1000 Series
Recording Software
IMZ-NS100 Series
PC
DIMENSIONS
2.07
( 52.7 )
3.70
R
( 94.1 )
10.07
( 255.8 )
Unit: inches (mm)
9.75
( 247.6 )
6.59
( 167.3 )
11.08
( 281.4 )
12.25
O
( 311.2 )
Sony Electronics Inc.
1 Sony Drive
Park Ridge, NJ 07656
sony.com/security
U-ID7C3/ID7T3
Reproduction in whole or in part without written permission is prohibited.
© 2012 Sony Electronics Inc. All rights reserved.
Features and specifications are subject to change without notice.
Weights and measurements are approximate.
Sony, the Sony make.believe and their respective logos are trademarks of Sony.
Printed in USA (01/12)