Sony SU-XFQ005 User Manual [en, es, fr]

Thank you for purchasing this product.
For customers
This product should be installed only by qualified Sony service representatives, as it requires at least two people, special care, safety, and technique.

WARNING

If the safety precautions are not observed or the product is used incorrectly, it may result in serious injury or fire.
US
For Sony dealers
Installation of a Display Unit requires two or more people, special care, and technique. When installing a Display Unit, refer to this manual carefully. Sony is not liable for any accidents or damages caused by incorrect installation or handling. Please instruct the customer to retain this manual for future use.
We recommend installing the Floor Stand a short distance away from the wall.
On Safety
Sony products are designed with safety in mind. If the products are used incorrectly, however, it may result in a serious situation like fire, electric shock, the product toppling over, or the product dropping. Be sure to observe the precautions for safety to prevent such accidents.
For Customers
WARNING
If the following precautions are not observed, serious injury or death through fire, electric shock, the product toppling over, or the product dropping can result.
This product should only be installed by qualified Sony service representatives.
Installation by other, non-qualified persons may result in serious injury, as the Display Unit and the stand are very heavy.
Do not lean on or hang from the stand.
The stand may topple over and cause injury.
Do not use a cracked stand.
Do not use the Floor Stand if any cracks appear in it. The glass may break and cause injury.
Cracked Stand
Do not lean on or hang from the Display Unit when it is attached to the Floor Stand.
The Floor Stand may topple over, or the Display Unit may fall and cause serious injury or death.
Do not climb on the stand or allow children between the shelf and the stand.
If children climb on the stand or allow children between the shelf and the stand, serious injury or death through the glass breaking, the stand toppling over, or the Display Unit dropping can result.
Do not cover the ventilation holes of the Display Unit.
If you cover the ventilation holes (with a cloth, etc.), heat build up inside may cause fire.
Be sure to take measures to prevent the Display Unit from toppling over.
If you fail to do so, the Display Unit may topple over and cause injury. Anchor the Display Unit to a wall, pillar, etc., to prevent it from toppling over.
Be sure to install the stand on a solid and level floor.
Do not install the Floor Stand so that it leans in one direction. If you do so, the Floor Stand may topple over or the Display Unit may fall. This may cause injury. If you install the stand on a soft surface such as a mat or a carpet, lay a board over the designated location beforehand.
2 (US)
Do not move the stand with the Display Unit attached or with connected equipment inside.
If you move the stand with the Display Unit attached, it may hurt your back, or the stand may topple over and cause serious injury. Also, any connected equipment within may drop causing the glass to break or other property damage.
Notes on handling the stand
Forcible handling of the stand may result in serious injury. Remove the Display Unit and the connected equipment before handling the stand, and follow the notes below.
• Be sure to have at least two people handle the stand.
• Do not grab the glass part.
• Be careful not to pinch your hands or feet.
CAUTION
If the following precautions are not observed, injury or property damage may occur.
Do not install any equipment other than the specified product.
This stand is designed for the use with the specified product only. If you install equipment other than specified, it may fall or break, and cause injury.
US
Do not allow the AC power cord or the display interface cable to be pinched.
Do not allow the AC power cord or the display interface cable to be pinched when you attach the Display Unit to the Floor Stand. If the AC power cord or the display interface cable is damaged, this may result in fire or electric shock.
Do not step on the stand.
You may fall, or break the glass and cause injury.
Do not stumble over the AC power cord or the display interface cable.
You may trip, or may cause the stand to topple over and cause injury. Bundle the cables according to the Operating Instructions to avoid stumbling on the cables.
Be sure to secure the Display Unit.
Secure the Display Unit to the Floor Stand using the supplied screws. If the Display Unit is not installed securely, it may fall, or the stand may topple over, and cause injury.
Do not apply weight to the glass or subject it to any kind of impact.
Do not apply pressure to the glass when installing the Display Unit. Do not hit the glass with hard objects, such as a screwdriver, etc. The glass may break and cause injury.
Do not subject the glass to excessive shock.
This stand is made of tempered glass, but care should be taken. If the glass breaks, glass fragments could cause injury, so observe the precautions below.
• Do not hit the glass or drop any objects that may break the glass. Avoid excessive shock.
• Do not scratch or poke the glass with sharp-pointed objects.
• Do not let hard objects such as a vacuum cleaner hit the edges of the glass.
Do not disassemble or modify the stand.
Do not pull out the screw that secures the glass shelf, or remove the glass. The connected equipment may drop, or the glass may break and cause injury or property damage.
Notes on installation
Install the stand on a solid and level floor. Be sure the stand is placed where it will not be deformed or inclined. To avoid this, observe the following precautions.
• Do not install the stand in a place subject to direct sunlight or near a heater.
• Do not install the stand in a hot or humid place, or outdoors.
3 (US)
Note on use
Cleaning
To keep the stand clean, occasionally wipe the stand with a dry soft cloth. Stubborn stains may be removed with a cloth slightly dampened with diluted detergent. Then wipe the area with a dry soft cloth. Do not use chemicals, such as thinner or benzine, as they damage the finish of the stand.
For Sony dealers
Be sure to thoroughly read the safety precautions described on the previous pages and pay special attention to safety during the installation, maintenance, checking, and repair of this product.
Be sure that two or more persons do the installation work.
Be sure that two or more persons install the Display Unit on the Floor Stand. If necessary, include another person to support the rear of the Display Unit. Do not attempt to install the stand by yourself. If you do so, it may lead to an accident or injury. Be sure to keep children away during the installation.

Check the parts

Name Quantity
Floor Stand
1
Display securing screw M5×L16
4
Anchor attachment
2
Cable cover
Be careful not to injure your hands or fingers during installation.
Be careful not to injure your hands or fingers when attaching the Display Unit to the Floor Stand.
Be sure to install the Display Unit securely by following the instructions.
Tighten the screws securely. If the Display Unit is not installed securely, it may fall and cause injury.
1
Cable cover securing screw M4×L12
2
Be sure to have appropriate sized Phillips screwdrivers on hand for the various sized screws used for assembly.
4 (US)

Install the Display Unit

WARNING
A short circuit or an electric shock may result if the AC power cord is pinched under the footing of the stand or between other equipment. If you stumble over the AC power cord or the display interface cable, the stand may topple over and cause injury.
Decide on the installation location and lay the stand down before installing the Display Unit.
Since the Display Unit is heavy, it is recommended that you decide on the installation location first, and then lay the Floor Stand down before installing the Display Unit.
Note
Do not drag the Floor Stand while it is on the floor. The rubber footings on the base of the Floor Stand may come off.
1 Attach the Display Unit to the
Floor Stand.
Use the screw alignment holes on the rear of the Display Unit as guides. Gently lower the Display Unit to align the holes of the screws over the joints of the Floor Stand.
Rear of Display Unit
US
The caution label is on the front side of the Floor Stand.
Bottom of Display Unit
Joint
This Display Unit has finger slots on both sides at the bottom for holding.
z Hint
There are finger slots located at the bottom of the Display Unit on both sides for holding. When attaching the Display Unit to the stand, use the slot to support the bottom and hold the top with your other hand.
Holes for the display securing screws
Guides
5 (US)
2 Secure the Display Unit to the
Floor Stand with the four display securing screws.
Rear of Display Unit
Display securing screw
M5×L16

Bundle the cables

1 Connect the AC power cord and
the display interface cable to the Display Unit.
z Hint
See the Operating Instructions supplied with the Display Unit for details on connecting the AC power cord and the display interface cable.
Note
When using an electric screwdriver, set the torque setting to about 1.5 N·m.
Display interface cable
AC power cord
6 (US)
2 Bundle the AC power cord and
the display interface cable.
1 Do not forcefully pull on the cables. Leave
some slack at the connected end as you thread the cables through the center hole on the stand. (Stand has two holes to thread the cables on the left and right sides.)
2 Thread the cables through either the left or
right side hole of the stand.
Slacken the cables.
1
2
3 Attach the cable cover.
1 Push any excess of cable inside the cable
compartment, and slide the cable cover down until the four tabs of the cable cover snap into place.
Cable cover
US
2 Affix the cable cover with the two screws for
the cable cover.
Cardboard or cloth
Thread the black and white display cables together through the hole.
Note
Do not forcefully pull the cable through the hole as the metallic part of the connector may scratch the floor. To avoid any damages to your floor, cover the floor with a piece of thin cardboard or a cloth during the installation.
Cable cover securing screw M4×L12
7 (US)
4 Use the cable clamps to hold the
cables in place. Unsnap the clamps and thread the AC power cord and display interface cable as shown.
Cable clamp

Safety measures to prevent toppling over

WARNING
Be sure to take measures to prevent the Display Unit from toppling over. If you fail to do so, the Display Unit may topple over and cause injury. Anchor the Display Unit to a wall, pillar, etc., to prevent it from toppling over.
Prepare a commercially available strong rope or chain and wall anchor bracket beforehand.
1 Attach the two anchor
attachments to the upper free screw holes on the rear of the Display Unit.
Cable
Pinch the cable clamps and push against the inserted cables to snap in.
Anchor attachment
2 Secure the wall anchor bracket
to a solid wall or pillar.
8 (US)
Loading...
+ 22 hidden pages