Sony STRKSL-40, STRSL-40 Service manual

STR-KSL40/SL40
SERVICE MANUAL
Ver 1.0 2003. 06
Photo : STR-SL40
• STR-KSL40 is the receiver section in HT-SL40.
Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic” and the double-D symbol are trademarks of Dolby Laboratories.
SPECIFICATIONS
Amplifier section POWER OUTPUT Models of area code CEL,CEK Rated Power Output at Stereo Mode
(8 ohms 1 kHz, THD 0.7 %) 25 W + 25 W
Reference Power Output
(8 ohms 1 kHz, THD 10 %)
Models of other area code Rated Power Output at Stereo Mode
(8 ohms 1 kHz, THD 0.7 %) 20 W + 20 W
Reference Power Output
(8 ohms 1 kHz, THD 10 %) FRONT1): 30 W/ch
1) Depending on the sound field settings and the source, there may be no sound output.
2) Measured under the following conditions:
Area code Power requirements
CEL, CEK 230 V AC, 50 Hz
Frequency response
TV/SAT, DVD, VIDEO: 10 Hz – 50 kHz
Inputs (Analog)
TV/SAT, DVD, VIDEO: Sensitivity: 250 mV
3) INPUT SHORT (with sound field and tone by passed).
4) Weighted network, input level.
2)
FRONT1): 35 W/ch CENTER1): 35 W SURR1): 35 W/ch
2)
CENTER1): 30 W SURR1): 30 W/ch
+0.5/–3 dB (with sound field and tone by passed)
Impedance: 50 kilohms S/N3): 96 dB (A, 250 mV4))
2)
2)
AEP Model
STR-KSL40/SL40
UK Model
STR-KSL40
Inputs (Digital)
DVD (Coaxial) Sensitivity: –
Impedance: 75 ohms S/N: 100 dB (A, 20 kHz LPF)
DVD, TV/SAT (Optical) Sensitivity: –
Impedance: – S/N: 100 dB (A, 20 kHz LPF)
Outputs
SUB WOOFER Voltage: 2 V
Impedance: 1 kilohms
Tone
Gain levels: ±6 dB, 1 dB step
Video section Inputs
Video: 1 Vp-p, 75 ohms
Outputs
Video: 1 Vp-p, 75 ohms
FM tuner section Tuning range 87.5 – 108.0 MHz Antenna terminals 75 ohms, unbalanced Intermediate frequency 10.7 MHz
Sensitivity
Mono: 18.3 dBf, 2.2 µV/75 ohms Stereo: 38.3 dBf, 22.5 µV/75 ohms
Usable sensitivity 11.2 dBf, 1 µV/75 ohms
FM STEREO
FM-AM RECEIVER
9-877-451-01
2003F02-1
© 2003.06
Home Audio Company
Published by Sony Engineering Corporation
STR-KSL40/SL40
S/N
Mono: 76 dB Stereo: 70 dB
Harmonic distortion at 1 kHz
Mono: 0.3% Stereo: 0.5%
Separation 45 dB at 1 kHz
Frequency response 30 Hz – 15 kHz
+0.5/–2 dB
Selectivity 60 dB at 400 kHz
AM tuner section Tuning range Models of area code CEL, CEK
With 9-kHz tuning scale: 531 – 1602 kHz
Antenna Loop antenna
Intermediate frequency 450 kHz
Usable sensitivity 50 dB/m (at 999 kHz)
S/N 54 dB (at 50 mV/m)
Harmonic distortion 0.5% (50 mV/m, 400 Hz)
Selectivity At 9 kHz: 35 dB
General Power requirements
Area code Power requirements
CEL, CEK 230 V AC, 50/60 Hz
TABLE OF CONTENTS
Specifications ............................................................................ 1
1. GENERAL ...................................................................... 3
2. TEST MODE ................................................................. 4
3. DIAGRAMS
3-1. IC Pin Function Descriptions ..................................6
3-2. Block Diagrams – Main Section – ........................ 10
Block Diagrams – Display/Power Section – ......... 11
3-3. Printed Wiring Boards
– Digital Section (Side A)– ................................... 12
Printed Wiring Boards
– Digital Section (Side B)– ................................... 13
3-4. Schematic Diagram – Digital Section (1/3)– ........ 14
3-5. Schematic Diagram – Digital Section (2/3)– ........ 15
3-6. Schematic Diagram – Digital Section (3/3)– ........ 16
3-7. Printed Wiring Boards – Main Section– ............... 17
3-8. Schematic Diagram – Main Section (1/2)– .......... 18
3-9. Schematic Diagram – Main Section (2/2)– .......... 19
3-10. Printed Wiring Boards – Display Section– ........... 20
3-11. Schematic Diagram – Display Section– ............... 21
3-12. IC Block Diagrams ................................................ 22
4. EXPLODED VIEWS
4-1. Front Panel Section ................................................. 23
4-2. Cabinet Section ........................................................ 24
Power consumption
Area code Power consumption
CEL, CEK 130 W
Power consumption (during standby mode)
0.3 W
Dimensions (w/h/d) 430 x 56 x 288 mm
including projecting parts and controls
Mass (Approx.) 4.5 kg
Supplied accessories (STR-SL40)
FM wire antenna (1) AM loop antenna (1) Remote commander RM-U40 (1) R6 (size-AA) batteries (2) Speakers plugs (5) Hexagon wrench (1)
Design and specifications are subject to change without notice.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PA RTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUM­BERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLE­MENTS PUBLISHED BY SONY.
5. ELECTRICAL PARTS LIST ....................................25
Unleaded solder
Boards requiring use of unleaded solder are printed with the lead­free mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size.)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40°C higher than
ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350°C. Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful!
• Strong viscosity Unleaded solder is more viscous (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc.
• Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder.
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be dam­aged by heat.
2
SECTION 1
GENERAL

List of Button Locations and Reference Pages

Main unit
Display 6 DVD (indicator) 3 INPUT SELECTOR 8 IR (receptor) 7 MASTER VOLUME 9 MUTING qs PRESET TUNING +/– qd SOUND FIELD qa TUNER (indicator) 5 TV/SAT (indicator) 4 VIDEO (indicator) 2
?/1 (power) 1 ; PLII q;
STR-KSL40/SL40
This section is extracted from instruction manual.
1
2 3 4 5 6 7 8 9 0
?/1
qd
qa
qs
3
STR-KSL40/SL40
SECTION 2

TEST MODE

FACTORY PRESET MODE
* All preset contents are reset to the default setting. * Procedure:
While depressing the PLII and the PRESET TUNING + but­tons simultaneously, press the power
button to turn on the
?/1
main power. The message “FACTORY” appears and the present contents are reset to the default values.
RDS AUTOBETICAL MODE
* This mode is installed in the Europe models only. When this
mode is used, the receiver scans the broadcasts that can be re­ceived by the tuner, and sets up the broadcasts. Be sure to start scanning after connecting the antenna.
* Procedure :
1. Check that the antenna is connected.
2. While depressing the INPUT SELECTOR button, press the
?/1 button to turn on the main power.
3. The message “AUTO-BETICAL SELECT” appears and the receiver starts scanning.
MICRO/NORMAL SPEAKER SELECTION MODE
* Either the micro speaker mode or normal speaker mode can be
selected.
*Procedure
While depressing the MUTING button, press the power
?/1
button to turn on the main power. Either the message “MICRO SP.” or “NORM. SP.” appears. Select the desired mode.
SOUND FIELD CLEAR MODE
* The preset sound field is cleared when this mode is activated.
Use this mode before returning the product to clients upon completion of repair.
* Procedure:
While depressing the SOUND FIELD button, press the power
button to turn on the main power. The message
?/1
“SF. CLR” appears and initialization is performed.
ALL CLEAR MODE
* The all preset value is cleared when this mode is activated. * Procedure :
While depressing the PLII and the PRESET TUNING - buttons simultaneously, press the power
button to turn on the main
?/1
power. The message “CLEARED” appears and clear all preset value.
SOFTWARE VERSION DISPLAY MODE
* The software version is displayed. * Procedure:
While depressing the SOUND FIELD and the PRESET TUN­ING - buttons simultaneously, press the power
?/1
button to turn on the main power. The model name, destination and the software version are displayed.
KEY CHECK MODE
* Button check * Procedure:
While depressing the MUTING and the INPUT SELECTOR buttons simultaneously, press the power the main power. “REST 06” appears. Every pressing of any button other than ?/1 counts down the buttons. The buttons which are already counted once are not counted again. When all buttons are pressed “REST 00” appears.
button to turn on
?/1
FLUORESCENT INDICATOR TUBE TEST MODE
* All fluorescent segments are tested. When this test is activated,
all segments turn on at the same time, then each segment turns on one after another.
* Procedure:
While depressing the MUTING and the PRESET TUNING
- buttons simultaneously, press the power
button to turn
?/1
on the main power.
1. All segments turn on.
D
D
DIGITAL
D
D
PRO LOGIC II
MPEG-2 AAC
DTS
L
SW
C
R
SL
SR
SSB
L F E
dB kHz mft. MHz
MEMORY
MONOSTD.RANGE
RDS
OPT COAX
VIDEO , DVD , TV/SAT and TUNER LED turn on.
2. Press the INPUT SELECTOR button, confirm display
D
D D
MPEG
DIGITAL
D
PRO LOGIC
L F E
LSW
CR
SRS
k m
MHz
RDS
ST
MONO
COAX
VIDEO , and TUNER LED turn on.
3. Press the INPUT SELECTOR button, confirm display
-2 AAC
DTS
II
SL
S B
dB
Hz
ft.
OPT
MEMORY
D.RANGE
DVD and TV/SAT LED turn on.
4. Press the INPUT SELECTOR button, all segments and LEDs turn off.
5. Every pressing of the INPUT SELECTOR button turns on each segment and LED one after another in the same order.
TUNER CHECK MODE
*Tuner check * Procedure :
While depressing the SOUND FIELD and the INPUT SE­LECTOR buttons simultaneously, press the power ?/1 but- ton to turn on the main power. “TUN CHK” appears and the tuner checking is performed.
DSP TEST MODE
* DSP tests are performed. * Procedure :
There are two different methods to enter the test mode.
(1) While depressing the INPUT SELECTOR and PRESET
TUNING - buttons simultaneously, press the power ?/1 button to turn on the main power.
(2) When the set is turned on, by using the remote controller, press
the ENTER button three times, then press the MAIN MENU button one time and thenpress the MUTING button one time.
• Select the item by pressing Cursor button ( V or v ).
• Select the function by pressing Cursor button ( B or b ).
4
• DSP Test Mode Items
Items
SWAP
DSP Version
DSP communication
Bass Management
Main Speaker cut off Freq.
LFE cut off Freq.
Co-ef. Read Address
Co-ef. Read Data
Co-ef. Write Address
Co-ef. Write Data
SRAM
Total operation time
Longest Power ON time
Output time less than
–50dB volume
Output time less than
–40dB volume
Output time less than
–30dB volume
Output time less than
–20dB volume
Output time less than
–10dB volume
Output time less than
0dB volume
Protector count value
Fuse open count value
EEPROM CONDITION
EEPROM READ
EEPROM Super Reset
DSP HALT MODE
Function
NORM
ALL
C SW
SLSR
OFF
ON
Description
Normal channel output
Left input t Front Left, Surround Left, Center channel output
Right input t Front Right, Surround Right, Sub Woofer channel output
Left input t Center channel output
Right input t Sub Woofer channel output
Left input t Surround Left channel output
Right input t Surround Right channel output
“DSPV XXX” is displayed. Three large charactors are the DSP version that is being used.
When this item is selected the message will be displayed “ OK ” if the checking is correct. “ ERROR ” will be displayed in a case of an error.
“SUR-NORM” is displayed.
“EQ-NORM” is displayed.
“DLY-NORM” is displayed.
“BM-NORM” is displayed.
Not used for service “BM. AUTO” is displayed.
Not used for service “MAIN 120 Hz” is displayed.
Not used for service “LFE 120 Hz” is displayed.
Not used for service “RA. XXXXX” is displayed.
Not used for service “RD. XXXXXX xx” is displayed.
Not used for service “WA. XXXXX” is displayed.
Not used for service “WD. XXXXXX xx” is displayed.
“ RAMC. OFF ” will be displayed in a case of no checking.
By pressing Cursor button the checking starts.
“ RAMC. PASS ” will be displayed if the checking is good. “ RAMC. NG ” will be displayed if an error occurs.
“TTL-XXXX xx” is displayed.
“LNG-XXXX xx” is displayed.
“V50-XXXX xx” is displayed.
“V40-XXXX xx” is displayed.
“V30-XXXX xx” is displayed.
“V20-XXXX xx” is displayed.
“V10-XXXX xx” is displayed.
“V00-XXXX xx” is displayed.
“PROT XXX” is displayed.
“FUSE XXX” is displayed.
“E- XXXX” is displayed.
S RST t Super Reset : first time use EEPROM or test pattern
corrupted
FAIL t EEPROM read / write with microcom has problem
V CHG t Software version change
D CHG t Destination / model change
CLEAR t Back up data initialize
NORM t Normal AC on
“E- XXX-XX” is displayed.
First four hex code is EEPROM address (controlled by +/– button).
Last two hex code is EEPROM data.
“S.RST- XXX” is displayed.
When YES is selected, press Cursor button to clear all EEPROM data
“HALT NO” or “HALT YES” is displayed.
STR-KSL40/SL40
Remark
Selection of setting
output channels
Checking communication between DSP and microcom
Checking communication between DSP and SRAM
Four large charactors are
hour. Two small charactors
are minutes.
0 to 255
5
STR-KSL40/SL40
SECTION 3
DIAGRAMS
3-1. IC Pin Function Descriptions
• IC1201 CXD9617R (AUDIO DSP) (DIGITAL BOARD)
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23 to 25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
Pin Name
VSS
XRST
EXTIN
FS2
VDD1
FS1
PLOCK
VSS
MCLK1
VDD1
VSS
MCLK2
MS
SCKOUT
LRCKI1
VDDE
BCKI1
SDI1
LRCKO
BCKO
VSS
KFSIO
SDO1 to SDO3
SDO4
SPDIF
LRCKI2
BCKI2
SDI2
VSS
HACN
HDIN
HCLK
HDOUT
HCS
SDCLK
CLKEN
RAS
VDDI
VSS
CAS
DQM/OE0
CSO
WEO
VDDE
WMD1
VSS
WMD0
PAGE2
VSS
PAGE1
I/O
Ground terminal
I
Rest input from the system control
I
Not used (connected to ground)
I
Not used (connected to ground)
Power supply (+2.5V)
I
Not used (connected to ground)
O
Not used (open)
Ground terminal
I
Clock input (13.5MHz)
Power supply (+2.5V)
Ground terminal
O
Clock output (13.5MHz)
I
Not used (connected to ground)
O
Internal system clock output to AK4527B
I
Not used (open)
Power supply (+3.3V)
I
Not used (open)
I
Serial data input from AK4527B
O
Sampling clock output to AK4527B
O
Bit clock output to AK4527B
Ground
I
Audio clock (384fs/256fs) input from LC89056W
O
Serial data output to AK4527B
O
Not used (open)
O
Not used (open)
I
Sampling clock input from LC89056W
I
Bit clock input from LC89056W
I
Serial data input from LC89056W
Ground
O
Acknowledge output to MB90478
I
Serial data input from MB90478
I
Clock input from MB90478
O
Serial data output to MB90478
I
Chip selection input from MB90478
O
Not used (open)
O
Not used (open)
O
Not used (open)
Power supply (+2.5V)
Ground
O
Not used (open)
O
Not used (open)
O
Chip selection output to the SRAM
O
Write enable output to the SRAM
Power supply (+3.3V)
I
Not used (connected to ground)
Ground
I
Not used (connected to VDD)
O
Not used (open)
Ground
O
Not used (open)
Description
6
STR-KSL40/SL40
Pin No.
53
54
55
56
57
58
59
60
61
62
63
64 to 66
67 to 69
70
71
72 to 75
76
77 to 80
81
82 to 85
86
87
88
89
90
91
92 to 97
98,99
100
101
102 to 105
106
107,108
109,110
111
112
113
114
115
116
117 to 119
120
Pin Name
PAGE0
BOOT
BTACT
BST
MOD1
MOD0
EXLOCK
VDDI
VSS
A17
A16
A15 to A13
GP10 to GP8
VDDI
VSS
D15/GP7 to D12/GP4
VDDE
D11/GP3 to D8/GP8
VSS
A9 to A10
TDO
TMS
XTRST
TCK
TDI
VSS
A8 to A3
D7,D6
VDDI
VSS
D5 to D2
VDDE
D1,D0
A2,A1
VSS
A0
PM
SD13
SD14
SYNC
VSS
VDDI
I/O
O
Not used (open)
I
Not used (connected to ground)
O
Not used (open)
I
Boot strap signal input from MB90478
I
Mode input (connected to VDD)
I
Mode input (connected to ground)
I
Lock signal input to LC89056W
Power supply (+2.5V)
Ground
O
Not used (open)
O
Not used (open)
O
Address bus output to the SRAM
I/O
External memory data I/O general purpose port terminal GP
Power supply (+2.5V)
Ground
I/O
SRAM data bus
Power supply (+3.3V)
I/O
SRAM data bus
Ground
O
Address bus output to the SRAM
O
Not used (open)
I
Not used (open)
I
Not used (open)
I
Not used (open)
I
Not used (open)
Ground
O
Address bus output to the SRAM
I/O
SRAM data bus
Power supply (+2.5V)
Ground
I/O
SRAM data bus
Power supply (+3.3V)
I/O
SRAM data bus
O
Address bus output to the SRAM
Ground
O
Address bus output to the SRAM
I
PLL initialization input from MB90478
I
Not used (open)
I
Not used (open)
I
Synchronization / asynchronous selection input (pull up)
Ground
Power supply (+2.5V)
Description
7
STR-KSL40/SL40
• IC1601MB90478PF-G-139-BND (SYSTEM CONTROL) (DIGITAL BOARD)
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Pin Name
DATA O
GP9
BST
HCS
HACN
XRST
PM
PD
SMUTE
CDT1
VSS
SCL
CS
DATA
CLK
LATCH
WOOFER RELAY
HDOUT
HDIN
HCLK
F.MUTE
VIDEO-SW1
VCC5
ANA/DIG
NOT IN USE
VIDEO SW2
FLASH2
FLASH1
VIDEO-MUTE
NC
NC
NC
SCL
SDA
AVCC
AVRH
AVSS
A/D0
A/D1
A/D2
A/D3
VSS
RDS SIGNAL
MODEL
VERSION
NC
CRYSTAL SEL
STOP
MD0
MD1
I/O
I
Serial data input from LC89056W
I
External memory data input from CXD9617R
O
Boot strap signal output to CXD9617R
O
Chip selection signal output to CXD9617R
I
Acknowledge signal input from CXD9617R
O
Reset signal output to CXD9617R
O
PLL initialization signal output to CXD9617R
O
PD signal output to AK4527B
O
Smute signal output to AK4527B
O
CDT1 signal output to AK4527B
Ground
O
Serial clock signal output to AK4527B
O
Chip selection signal output to AK4527B
O
Serial control data output to the tuner and M61527FP
O
Serial control clock output to the tuner and M61527FP
O
Latch signal to M61527FP
O
Sub woofer relay control signal output
I
Serial data input from CXD9617R
O
Serial data output to CXD9617R
O
Clock signal output to CXD9617R
O
Function mute signal output
O
Video switch signal output to the NJM2279
Power supply (+3.3V (STBY))
O
Function mute and error port signal output
I
Not used (pull down)
O
Video switch signal output to NJM2279
I
Flash programming input
I
Flash programming input
O
Video mute signal output to NJM2279
I
Not used (pull down)
I
Not used (pull down)
I
Not used (pull down)
O
SCL signal output to the EEPROM
I/O
SDA signal from the EEPROM
Power supply (+3.3V(STBY))
I
A Vref input (connected to +3.3 (STBY))
Ground
I
Not used (pull down)
I
Key signal input
I
Key signal input
I
Key signal input
Ground
I
RDS signal input to tuner
I
Model detection input
I
Version resisrtor input
I
Not used (pull down)
I
Not used (pull down)
I
AC off signal input
I
Flash programming MD0 input
I
Not used (connected to +3.3V(STBY))
Description
8
STR-KSL40/SL40
r
Pin No.
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87 to 92
93
94
95
96
97
98
99
100
Pin Name
MD2
RDS CLK
RDS DATA
SIRCS
FUSE DETECT
POWER KEY
NOT IN USE
NOT IN USE
VOL(B)
VOL(A)
DIN
CLK
FL_STB
FAN_ON
FAN_CLK
POWER RELAY
PROTECTOR
F_CTRL2
F_CTRL1
REAR RELAY
CENTER RELAY
PREOUT/FRONT RELAY
TUNED
STEREO
MUTE
DO
RSTX
SLATCH
X1A
X0A
VSS
XO
XI
VCC3
NOT IN USE
NC
NOT IN USE
XMODE
CKSEL1
CLK
CE
DI
DO
ERROR
XSTATE
I/O
I
Flash programming MD2 input
I
RDS clock input to tuner
I
RDS data input to tuner
I
Data input from the remote control receiver
I
Power supply off detect (connected to +3.3V)
I
Power swich detection signal input
I
Not used (pull down)
I
Not used (pull down)
I
Volume signal input from the rotary encoder
I
Volume signal input from the rotary encoder
O
Serial data output to µPD16315
O
Clock signal output to µPD16315
O
STB signal output to µPD16315
I
Fan motor on detection signal input
I
Feedback signal input from fan motor
O
Power relay drive signal output
I
Protect detection signal input
O
Fan speed control signal output
O
Fan ON/OFF control signal output
O
Surround relay drive signal output
O
Center relay drive signal output
O
Front relay drive signal output
I
Tuning a frequency detection signal input from the tuner
I
STEREO tuning signal from the tuner
O
Muting control signal output from the tuner
I
Data input from the tuner
I
System reset input
O
Serial control latch signal output to the tuner
Not used (open)
Not used (connected to ground)
Ground
O
Clock output (16MHz)
I
Clock input (16MHz)
Power supply (+3.3V (STBY))
I
Not used (pull down)
I
Not used (pull down)
I
Not used (pull down)
O
Reset signal output to LC89056W
O
Not used
O
Clock signal output to LC89056W
O
Chip enable signal output to LC89056W
O
Write data output to LC89056W
I
Read data input from LC89056W
I
PLL lock error, data error flag input from LC89056W
I
Source clock selection monitor input from LC89056W
Description
• Circuit Boards Location
STANDBY board
POWER SW board
MAIN board
DISPLAY board
DIGITAL board
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this necessary note is printed in each block.)
For schematic diagrams. Note:
• All capacitors are in µF unless otherwise noted. p : pF. 50 WV or less are not indicated except for electrolytics and tantalums.
• All resistors are in and 1/ specified.
•%: indicates tolerance.
f
2 : nonflammable resistor.
C : panel designation.
Note: The components identified by mark 0 or dotted line
A : B+ Line.
B : B– Line.
•Voltages and waveforms are dc with respect to ground
•Voltages are taken with a VOM (Input impedance 10 M).
•Waveforms are taken with a oscilloscope.
• Circled numbers refer to waveforms.
• Signal path.
: internal component.
with mark 0 are critical for safety. Replace only with part number specified.
under no-signal (detuned) conditions. No mark : FM
Voltage variations may be noted due to normal produc­tion tolerances.
F : ANALOG J : DIGITAL c : DVD
W or less unless otherwise
4
For printed wiring boards. Note:
X : parts extracted from the component side.
a
: Pattern from the side which enables seeing.
Caution: Pattern face side: Parts on the pattern face side seen from (Side A) the pattern face are indicated. Parts face side: Parts on the parts face side seen from (Side B) the parts face are indicated.
: Through hole.
FM/AM tune
99
STR-KSL40/SL40
3-2. BLOCK DIAGRAM – MAIN SECTION –
COAXIAL
DIGITAL
AUDIO
VIDEO
COAXIAL IN
TV/SAT
DVD
VIDEO
TV/SAT OPT IN
DVD
OPT IN
DVD
MONITOR
OUT
VIDEO
IN
DVD
IN
L
R
L
R
L
R
ANTENA
RECEIVER
RECEIVER
J301
J401
J251
IC301
OPTICAL
IC302
OPTICAL
FM 75
AM
L CH
R CH
IC201
VIDEO SWITCH
L CH
R CH
L CH
R CH
INPUT SELECT, VOLUME CONT
78
INL4
79
INR4
74
INL7
INR7
75
70
INL8
59
INR8
2
INL2
3
INR2
TM301
TUNER UNIT
MUTE
STEREO
TUNEDCEST-DI/MC-DO
MUTE
STEREO
TUNED
11 10
IC401
SELECT OR
A+5V
VC
LATCHDIDO
WAVE SHAPER
IC303
SROUT
SWOUT
VOLUME
ATT
BAL L+
BAL R+
14
17
111312
AMP
AMP
4
ST-DO/MC-DI
CLK
SCLK
98
LOUT
ROUT
COUT
SLOUT
LIN2
RIN2
CIN2
SLIN2
SRIN2
SWIN2
DATA
CLK
LATCH
DVDD
IC1502
6
5
IC1552
6
5
FM SIGNAL OUT
R-SIG
R-CLK
54
47
36
41
42
35
20
21
24
23
22
25
28
27
29
30
7
7
10
5231
RDS INT
RDS DATA
R-DATA
IC1502
2
3
IC1552
2
3
1
1
29
26
22
MUTE
Q361-366
R-SIG
R-CLK
52
43
RDS CLK
RDS SIGNAL
VIDEO-MUTE
VIDEO-SW2
VIDEO-SW1
R-DATA
53
RDS DATA
X1101
12.288MHz
L-CH
R-CH
C-CH
SL-CH
SR-CH
SW-CH
DO
LATCH
76DO75
78
SLATCH
MUTE
MUTE
27
28
23
25
26
24
30
32
MUTE DRIVE
STEREO
74
STEREO
+3.3V
Q401
Q379
TUNED
73
DIGITAL AUDIO
I/F RECEIVER
21 XOUT
XIN
22
DIN1
4
DIN0
3
DIN2
5
LOUT1
ROUT1
LOUT3
LOUT2
ROUT2
ROUT3
LIN+
RIN+
REG
DI
SCLK
TUNED
IC1101
DO
XMODE
OUTPUT CIRCUIT
INPUT
CIRCUIT
+7V
FUNCTION MUTE SW
Q1601, 1602
IC701 POWER AMP
1IN
IC751 POWER AMP
1IN
IC501 POWER AMP
1IN
IC601 POWER AMP
1IN
IC651 POWER AMP
1IN
GP8
69
LRCKI2
28
BCKI2
29
KFSIO
22
SDI2
30
BCKO
20
LRCK
19
SDO1
23
SDO2
24
SDO3
25
SDI1
18
SCKOUT
14
EXLOCK
XRST
HACN
HDIN
59 2 32 33 34 35 36 56
6 5 19 20 18 4 3
HDIN
XRST
HACN
OUT
OUT
OUT
OUT
OUT
IC1201
AUDIO DSP
HCLK
HDOUT
HCLK
HDOUT
4
4
4
4
4
PROTECT DET
Q730-732
RELAY SW
Q720, 520, 620
RY701
RY501
RY601
IC402 SW AMP
7OUT5IN
FAN ON/OFF DET
Q550, 551
HCS
HCS
BST
BST
9MCLK1
X1201
13.5MHz
12MCLK2
A0-A15
D0-D15
44CSO
45WEO
GP9
PM
68
113
2
7
100
1
99
PM
GP9
DATAO
ERROR
XSTATE
98DO97
DI
17
96CE95
IC1202
SDRAM
6
CS
WE
CLK
94
93
CKSEL1
XMODE
67
PROTECTOR
D721
D521
D621
72
71
70
REAR RELAY
CENTER RELAY
PREOUT/FRONT RELAY
64
FAN_ON
13CS12
AUDIO
LRCK
BCK
CKOUT
SCL
L-CH
R-CH
C-CH
SL-C H
SR-CH
SW-CH
10
CDT1
AUDIO
24AUDIO
LRCK
15LRCK
BCK
14BCK
CKOUT
13CKOUT
16DATAO
17XSATE
34ERROR
35
DI
36
37CE
38CLK
47CKSE1
48
IC1501 CODEC
AUDIO
INTERFACE
D1601
14
15
DATA
CLK
16
LATCH
24 21
ANA/DIG
3 17
9 8
F.MUTE
D1101
DATAO
BCLK
4
LRCK
5
SDTI1
6
SDTI2
7
SDTI3
8
SDT0
9
MCLK1
39
CDT1
43
CCLK
42
CS
41
S.MUTE
PD
PD
SMUTE
IC1601 (1/2)
SYSTEM CONTROL
RY401
TM601
CENTER
RELAY SW
Q402
17
L
R
L
R
J403
WOOFER RELAY
WOOFER
• Signal Path
: ANALOG
FRONT
SUB
OUT
SURR
SPEAKERS
IMPEDANCE
USE 8-16
: DIGITAL
: DVD
1010
Loading...
+ 23 hidden pages