• STR-KM5000 is the receiver section in HT-DDW5000.
This receiver incorporates Dolby* Digital and Pro Logic Surround and the DTS** Digital Surround System.
* Manufactured under license from Dolby Laboratories. Dolby, Pro Logic, and the double-D symbol are
trademarks of Dolby Laboratories.
This receiver incorporates High-Definition Multimedia Interface (HDMI
HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks
of HDMI Licensing LLC.
TM
) technology.
SPECIFICATIONS
Amplifier section
Power Output
Models of area code SP, MY, MX, E51, AR, TH
Stereo mode output (rated) (6 ohm, 1 kHz,
THD 1%)
90 W + 90 W
85 W + 85 W
Surround mode output (reference)
RMS output
FRONT:185 W per channel
170 W per channel
(with SS-MSP5000)
CENTER:185 W
170 W
(with SS-CNP5000)
SURROUND:185 W per channel
170 W per channel
(with SS-SRP5000)
SURROUND BACK:
185 W
170 W
(with SS-SRP5000)
1)
2)
3)
1)
2)
1)
2)
1)
2)
1)
2)
Measured under the following conditions:
Area codePower requirements
E51, SP, MY 240 V AC, 50 Hz
MX127 V AC, 60 Hz
AR, TH 230 V AC, 50 Hz
2)
Measured under the following conditions:
Area codePower requirements
AR, TH 220 V AC, 50 Hz
3)
Reference power output for front, center, surroun
and surround back speakers. Depending on the
sound field settings and the source, there may be
no sound output.
Audio&Video Business Group
Published by Sony Techno Create Corporation
Page 2
STR-KM5000
Model
AR
Ver. 1.1
s of area code MX,
With 10-kHz tuning scale:
AntennaLoop antenna
Intermediate frequency
4)
You can change the AM tuning scale to 9 kHz or
10 kHz. After tuning in any AM station, turn off
the receiver. While holding down TUNING
MODE, press . All preset stations will be
erased when you change the tuning scale. To reset
the scale to 10 kHz (or 9 kHz), repeat the
procedure.
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS
WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
SAFETY-RELATED COMPONENT WARNING!
2
7. EXPLODED VIEWS
7-1. Front Panel Section ......................................................... 53
7-2. Back Panel Section ......................................................... 54
7-3. Main Section ................................................................... 55
8. ELECTRICAL PARTS LIST .............................. 56
Note: Refer to supplement-1 for the DIGITAL AB board of printed
wiring board, schematic diagram and electrical parts list of
Thai model.
Page 3
SECTION 1
SERVICING NOTES
STR-KM5000
Ver. 1.1
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be damaged by heat.
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscou-s (sticky, less prone to fl ow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
MODEL IDENTIFICATION
– Rear View –
ModelPart No.
Singapore and Malaysia models
Argentina model
Thai model
Chilean and Peruvian models
Mexican model
NOTE OF REPLACING THE IC1131 ON THE DIGITAL
AB BOARD
IC1131 on the DIGITAL AB board cannot exchange with single.
When IC1131 on the DIGITAL AB board is damaged, exchange
the entire mounted board.
3
Page 4
STR-KM5000
R
Receiver
Front panel
SECTION 2
GENERAL
This section is extracted
from instruction manual.
TUNING MODE
– +
VIDEO 2 IN/PORTABLEAV IN
VIDEO L AUDIO R
TUNING
MEMORY/
ENTERSLEEPDIMMER
AUTO CAL
AUTO CAL MIC
PHONES
M
NameFunction
" /
(on/standby)
# AUTO CALPresstoactivatetheAuto
$ TUNING MODE Press or turntooperatethe
TUNING +/–
% DisplayThe current status of the
& MULTI CHANNEL
DECODING
lamp
' Remote sensor Receivessignals from
( DISPLAYPresstoselectinformation
) INPUT MODEPress to select the input
* MASTER
VOLUME
+ X-ROUND MODE Press to select the X-
X-ROUND
SPEED
Press to turn the receiver
on or off.
Calibrationfunction.
tuner (FM/AM).
selected component or a
list of selectable items
appears here.
Lights up when multi
channel audio signals are
decoded.
remote commander.
displayed on the display.
mode when the same
componentsareconnected
to both digital and analog
jacks.
Turn to adjust the volume
level of allspeakers atthe
same time.
ROUND mode.
Presstoadjustthespeedof
the X-ROUNDeffect.
MULTI CHANNEL DECODING
SUR BACK
2CH A.F.D. MOVIE MUSIC
DECODING
RERGRHRI
DISPLAYINPUT MODE
INPUT SELECTOR
RBRTRKRL
NameFunction
, INPUT
SELECTOR
- 2CHPress to select a sound
A.F.D.
MOVIE
MUSIC
. SUR BACK
DECODING
/ SLEEPPress to activatethe Sleep
0 DIMMERPress to change the
1 MEMORY/
ENTER
2 VIDEO 2 IN/
PORTABLE AV
IN jacks
3 AUTO CAL MIC
jack
4 PHONES jackConnects to headphones.
Turn to select the input
source to play back.
field.
Press to select the
surround back decoding
mode.
Timer functionand the
duration whichthe
receiver turns off
automatically.
brightness ofthe display.
Press to store a station or
enter the selection when
selecting the settings.
Connect to a portable
audio/video component
such as a camcorderor
video game.
Connects tothe supplied
optimizer microphone for
the Auto Calibration
function.
MASTERVOLUME
X-ROUND
MODESPEED
R
4
Page 5
About the indicators on the display
D EXPLIIxPLOPTDTS -ES 96/24MEMORYST
LFE
SW
LC
SL S
SB
R
SR
STR-KM5000
MONOD.RANGECOAXHDMINEO:6
RRGRTRERB
NameFunction
" SWLightsup when the audiosignal
# LFELights up when the disc being
$ D/
DEX
% PL/
PLII/
PLIIx
& OPTLights upwhen INPUT MODE
' DTS/
DTS-ES/
DTS 96/24
is output from the
SUBWOOFER jack.
played backcontains anLFE
(Low Frequency Effect)
channel and the LFEchannel
signal is actually being
reproduced.
“D” lights up when Dolby
Digital signals are input.
“D EX” lights up when
Dolby Digital Surround EX
signals aredecoded.
Note
When playing a Dolby Digital
format disc, be sure thatyou
have made digital connections
andthatINPUT MODE issetto
“AUTO”.
“PL” lights up when the
receiver applies Pro Logic
processing to 2 channel signals
inorder to outputthecenterand
surround channel signals.
“PLII” lights up when the
Pro Logic II Movie/Music/
Game decoderis activated.
“PLIIx” lights up when the
Pro Logic IIxMovie/Music/
Game decoderis activated.
Note
Dolby Pro Logic IIx decoding
does not function for DTS
format signals or for signals
with a sampling frequency of
more than 48 kHz.
issetto“AUTO”andthesource
signal is a digital signal being
input through the OPTICAL
jack.
“DTS” lights up when the
receiver is decoding DTS
signals.
“DTS-ES” lights up when the
receiver is decoding DTS-ES
signals.
“DTS96/24”lightsupwhenthe
receiver is decoding DTS 96
kHz/24 bit signals.
Note
When playing a DTS format
disc,besurethatyou have made
digital connections and that
INPUT MODEis setto
“AUTO”.
NameFunction
( MEMORYLights upwhen a memory
) Tuner
indicators
* Preset
station
indicators
+ D.RANGELights upwhen dynamic range
, NEO:6Lights up when DTS Neo:6
- COAXLightsup when INPUTMODE
. HDMILights up whenthe receiver
/ Playback
channel
indicators
L
R
C
SL
SR
S
SB
function, suchas Preset
Memory, etc., is activated.
Lights up when using the
receivertotunein radio stations
, etc.
Lights up when using the
receivertotunein radio stations
you have preset. For details on
presetting radio stations.
compression is activated.
Cinema/Music decoder is
activated.
issetto“AUTO”andthesource
signal is a digital signal being
input through the COAXIAL
jack.
recognizes a component
connectedviaan HDMI IN jack.
The letters (L, C,R, etc.)
indicate the channels being
played back. The boxes around
theletters vary toshowhow the
receiver downmixesthe source
sound.
Front Left
Front Right
Center (monaural)
Surround Left
Surround Right
Surround (monaural or the
surround components obtained
by Pro Logic processing)
Surround back (the surround
back componentsobtained by
6.1 channeldecoding)
Example:
Recording format(Front/
Surround): 3/2.1
Sound Field: A.F.D. AUTO
SW
LC
R
SL
SR
5
Page 6
STR-KM5000
Rear panel
DIGITAL
DC5V
0.7A MAX
ANTENNA
L
R
SA-CD/CD/CD-R
OPTICAL
BD
IN
SAT
IN
COAXIAL
DVD
IN
DMPORT
DVD INBD INOUT
AM
HDMI
VIDEO
VIDEO
IN
IN
AUDIO
AUDIO
IN
IN
ININOUT
TV SAT DVD VIDEO 1
VIDEO
AUDIO
OUT
SAT IN
DVD IN BD IN MONITOR OUT
Y
B
P
/
B
SURROUND
BACK
C
P
R
/
R
C
FRONT: ONLY FOR SS-MSP5000
CENTER: ONLY FOR SS-CNP5000
SURROUND: ONLY FOR SS-SRP5000
SURROUND
LR
CENTER
SPEAKERS
FRONT
L
R
VIDEO
VIDEO
OUT
IN
OUT
COMPONENTVIDEO
MONITOR
AUDIO
AUDIO
IN
OUT
L
R
SUBWOOFER
" DIGITAL INPUT/OUTPUT section
OPTICAL
IN jacks
COAXIAL IN
jack
HDMI IN/
OUT* jacks
Connects to a DVD
player, etc. The
COAXIAL jack
provides a better
sound quality.
Connects to a DVD
player, etc. The
image andthe sound
are output to a TV.
# ANTENNA section
FM
ANTENNA
jack
AM
ANTENNA
terminals
Connects to the
supplied FM wire
antenna.
Connects to the
supplied AM loop
antenna.
$ COMPONENT VIDEO INPUT/
OUTPUT section
Green
(Y)
Blue
B/CB)
(P
Red
(P
R/CR)
Y, PB/CB,
R/CR IN/
P
OUT* jacks
Connects to a DVD
player, TV, satellite
tuner, etc. You can
enjoy high quality
image.
% SPEAKERS section
Connects to the
supplied speakers .
& AUDIO INPUT/OUTPUT section
White (L)
Red (R)
Black
AUDIO IN/
OUT jacks
AUDIO OUT
jacks
Connects to a Super
Audio CD player,
etc.
Connects to the
supplied
subwoofers.
' VIDEO/AUDIO INPUT/OUTPUT
section
White (L)
Red (R)
Yellow
AUDIO IN/
OUT jacks
VIDEO IN/
OUT* jacks
Connects to a VCR,
DVD player, etc.
( DMPORT
DMPORT
jack
*You can watch the selected input image when you
connect the HDMI OUT or MONITOR OUT jack
to a TV.
Connects to a
DIGITAL MEDIA
PORT adapter.
6
Page 7
Remote commander
STR-KM5000
Youcan use thesuppliedremoteto operatethe
receiver andto control theSony audio/video
components thatthe remote isassigned to
operate. Fordetails, see “Changingbutton
assignments”.
RM-AAU027
TV INPUT
XB
VIDEO1 VIDEO2BDDVD
X
RM
RL
DISPLAY
RK
RI
RH
RETURN/EXIT
TV CH –
PRESET –
TUNING –
RG
TV
DMPORT
SLEEP
SATTV SA-CD/CD TUNER
2CHA.F.D.
123
46
78
>10/
-/--
CLEAR
0
TV
AV
SYSTEM STANDBY
MOVIE MUSIC
5
9
MEMORY
0/10
ENTER
TOOLS/
OPTIONS
MASTER VOL
MENU/HOME
REPLAY ADVANCE
).N
9Y
DVD/BD
MENU
AUTO CAL
D.TUNING
D.SKIP
AMP MENU
MUTING
TV VOL
TV CH +
PRESET +
TUNING +
FM MODE
R
RB
RT
RE
NameFunction
" TV /
(on/standby)
AV /
(on/standby)
# /
(on/standby)
$ Input
buttons
% 2CHPress to select a sound field.
A.F.D.
MOVIE
MUSIC
& DVD/BD
MENU
' AUTO CAL Press toactivate theAuto
( D.TUNINGPress to enter direct tuning
D.SKIPPress to skip a disc whenusing
Press TV / and TV(/)at
the same timetoturn the TVon
or off.
PresstoturnonorofftheSony
audio/video components that
the remote is assigned to
operate.
If you press / (#) at the
same time, it willturn off the
receiver and other components
(SYSTEM STANDBY).
Note
The functionof theAV /
switch changesautomatically
each time you press the input
buttons ($).
Press to turn the receiver on or
off.
To turn off all components,
press / and AV / (")at
the same time (SYSTEM
STANDBY).
Press one of the buttons to
select the component you want
to use. When you press any of
the input buttons, the receiver
turns on. The buttons are
factoryassignedtocontrolSony
components. You can change
the button assignments
following the steps in
“Changingbuttonassignments”.
Pressto display themenuof the
DVD or Blu-raydiscon the TV
screen.Then,use7,W, #, C and
(1)toperformmenu
operations.
Calibration function.
mode.
a multi-disc changer.
NameFunction
) AMP MENUPress to display themenu of
* ENTERPress toenter thevalue after
MEMORYPresstostoreastation.
+ MUTINGPress toturn offthe sound
, TV VOL
a)
/–
+
MASTER
a)
VOL +
- MENU/HOME Press todisplay themenu of
. /
REPLAY/
ADVANCE
N/.
a)b)
)
the receiver. Then, use 7, W ,
#, C and(1)toperform
menu operations.
selecting a channel, disc or
track usingthe numeric
buttons of the TV, VCR or
satellite tuner.
temporarily.
Press MUTINGagain to
restore thesound.
Press MUTING and TV (/)
at the same timeto activate
the TV’s muting function.
Press TVVOL +/–and TV
(/)atthesametimetoadjust
the TV volume level.
Press toadjust the volume
/–
level of all speakers at the
same time.
the VCR, DVD player,
satellite tuner or Blu-ray disc
player on the TV screen.
Press MENU/HOME and TV
(/) atthe same time to
displaythe TV’smenu.Then,
use7, W, #,C and(1)to
perform menu operations.
b)
PresstoskipatrackoftheCD
player, DVDplayer orBluray disc player.
Press toreplay the previous
scene or fast forward the
current scene of the VCR,
DVD player or Blu-ray disc
player.
b)
Press to
– search tracksin the forward/
reverse directionof the
DVD player.
– start fast forward/rewind of
the VCR,CD player or Bluray disc player.
Press tostart playback of the
VCR,CDplayer,DVD player
or Blu-ray disc player.
7
Page 8
STR-KM5000
NameFunction
b)
9
b)
Y
TV CH +/–Press TVCH+/–andTV(/)
PRESET +/– Press to select
TUNING +/–Press to scan a station.
FM MODEPress to select the FM
/ TVPress TV and the button with
0 RETURN/
EXIT 0
Press to pause playback or
recording of the VCR, CD
player, DVD player or Bluray disc player. (Also starts
recording with components in
recording standby.)
Press to stop playback of the
VCR, CDplayer, DVD player
or Blu-ray disc player.
at the same time to select
preset TV channels.
– preset stations.
– preset channels of the VCR
or satellite tuner.
monaural or stereo reception.
orange printing at the same
time to enable the TV
operation.
Press to
– return to the previous menu.
– exit the menu while the
menu or on-screen guide of
the VCR, DVD player,
satellite tuner or Blu-ray
disc player is displayed on
the TV screen.
Press RETURN/EXIT 0
and TV (/) at the same time
to return to theprevious menu
or exit the TV’s menu while
the menu is displayed on the
TV screen.
NameFunction
1
7/W/#/C
2 DISPLAYPress to select information
3 TOOLS/
OPTIONS
4 -/--Press to select the channel
Y
>10/
CLEARPress to clear a mistake when
After pressing DVD/BD
MENU (&), AMP MENU
()) or MENU/HOME (-),
press 7, W, # or C to select the
settings. Then, pressto
enter the selection if you have
pressed DVD/BD MENU or
MENU/HOME previously.
Pressalso to enter the
selection of the receiver,
VCR, satellite tuner, CD
player, DVD player or Bluray disc player.
displayed on the TV screen of
the VCR, satellite tuner, CD
player, DVD player or Bluray disc player.
Press DISPLAY and TV (/)
at the same time to display
TV’s information on the TV
screen.
Press to display and select the
options of the DVD player or
Blu-ray disc player.
Press TOOLS/OPTIONS and
TV (/) at the same time to
display options applicable to
the Sony TV.
entry mode, either one or two
digits of the VCR.
Press -/-- and TV (/) at the
same time to select the
channel entry mode, either
one or two digits of the TV.
Press to select
– track numbers over 10 of the
VCR, satellite tuner or CD
player.
– channel numbers of the
Digital CATV terminal.
you press the incorrect
numeric button.
NameFunction
5 Numeric
buttons
(number 5
6 TV INPUTPressTVINPUTandTV(/)
SLEEPPress to activate the Sleep
a)
The number 5, MASTER VOL +, TV VOL + and
) buttons have tactile dots. Use the tactile dots
as references when operating the receiver.
b)
This button is also available for DIGITAL
MEDIA PORT adapter operation. For details on
the function of the button, see the operating
instructions supplied with the DIGITAL MEDIA
PORT adapter.
Press to
– preset/tune to preset
a)
)
stations.
– select track numbers of the
CD player, DVD player or
Blu-ray disc player. Press 0/
10 to select track number 10.
– select channel numbers of
the VCR or satellite tuner.
Press the numeric buttons and
TV (/) at the same time to
select the TV channels.
at the same time to select the
input signal (TV input or
video input).
Timer function and the
duration which the receiver
turns off automatically.
Notes
• Some functions explained in this section may not
work depending on the model.
• The above explanation is intended to serve as an
example only. Therefore, depending on the
component, the above operation may not be
possible or may operate differently than described.
8
Page 9
DISASSEMBLY
• This set can be disassembled in the order shown below.
3-1. DISASSEMBLY FLOW
SET
3-2. CASE
(Page 9)
3-3. BACK PANEL BLOCK
(Page 10)
STR-KM5000
SECTION 3
3-4. FRONT PANEL BLOCK
(Page 10)
Note: Follow the disassembly procedure in the numerical order given.
3-5. MAIN BLOCK
(Page 11)
3-6. MAIN BOARD
(Page 11)
3-2. CASE
two screws
(BVTP3 × 8)
case
two screws
(BVST4 × 8)
two screws
(BVST4 × 8)
9
Page 10
STR-KM5000
3-3. BACK PANEL BLOCK
• Abbreviation
E51: Chilean and Peruvian models
connector
(CNP912)
screw
RG
(BVTP3 × 8)
three connectors
(CNP902, CNP910, CNP913)
(E51 only)
AC SELECT board
RE
connector
RT
(CNP905)
connector
RB
(CNP903)
clamp
screw
R
(BVTP3 × 8)
X
back panel block
screw
RH
(BVTP3 × 8)
connector (CNP505)
connector (CNP503)
two screws
RI
(BVTP3 × 8)
six screws
RK
(BVTP3 × 8)
five screws
RL
(BVTP3 × 8)
connector
(CNP240)
3-4. FRONT PANEL BLOCK
three leads (with connector)
(TP202, TP790, TP2000)
front panel section
connector
(CN102)
connector
(CN790)
connector (CNP203)
claw
screw (BVTP3 × 8)
RM
wire (flat type) (19 core)
(CNS514)
claw
three connectors
(CNP430, CNP500, CNP930)
10
five screws
(BVTP3 × 8)
Page 11
3-5. MAIN BLOCK
(CN790)
connector
three screws
(BV3)
(CNP921, CNP940)
two connectors
main block
two screws
(BV3)
two screws
(BV3)
STR-KM5000
3-6. MAIN BOARD
screw
(BV3)
wire route board
heatsink assy
three connectors
(CNP430, CNP500, CNP930)
(transistor)
twelve sheets
six transistor MP1620-OPY-MK
(Q604, Q654, Q704, Q754,
Q804, Q854)
Remove the
thirty six solders.
twelve screws
six transistor MN2488-OPY-MK
(Q603, Q653, Q703, Q753, Q803, Q853)
MAIN board
two screws
(BVTP3 × 8)
11
Page 12
STR-KM5000
SECTION 4
TEST MODE
TUNER AM STEP CHANGE (9 kHz/10 kHz) MODE
(Chiliean and Peruvian models only)
The AM tuning interval can be changed over 9 kHz or 10 kHz.
Procedure:
1. Press the [
] button to turn on the main power.
?/1
2. Turn the [INPUT SELECTOR] dial to select the “AM”.
3. Press the [
4. While pressing the [TUNING MODE] button, press the [
] button to turn off the main power.
?/1
?/1
button to turn on the main power.
5. The AM turning interval changed over 9 kHz or 10 kHz.
FL CHECK MODE
All fl uorescent segments are tested. When this test is activated, all
segments turn on at the same time, then each segment turns on one
after another.
Procedure:
1. When pressing the [TUNING MODE] and [DISPLAY] buttons, press the [
] button to turn on the main power.
?/1
2. All segments turn on.
LFE
SW
L CR
S
SR
SL
SB SBRSBL
SP A
SP B
D EX
PL II xPL
OPT
HDMI COAX
DTS-ES 96 / 24
CAT
NEO:6 SAT D.RANGE
MEMORY
dB
k Hz
mft.
MHz
RDS ST
MONO
3. Turn the [INPUT SELECTOR] dial.
4. Test pattern 1 turn on.
k
m
MHz
RDS ST
MONOCOAX
LFE
LR
S
SP B
PL II x
NEO:6D.RANGE
5. Turn the [INPUT SELECTOR] dial once again.
6. Test pattern 2 turn on.
SW
C
SLSR
SB SBRSBL
D
DTS
PL
CAT
MEMORY
dB
Hz
ST
ft.
KEY CHECK MODE
This mode is used to check the key.
Procedure:
1. While pressing the [AUTO CAL] and [2CH] buttons, press the
[
] button to turn on the main power.
?/1
2. The message “REST 14” appears.
3. Every pressing of any button other than the [
]
down the buttons. The buttons which are already counted once
?/1
are not counted again.
4. When all buttons are pressed, the message “REST 00” appears.
SWAP ALL MODE
When this mode is used, output the audio signal of front L/R channel to all channel.
Procedure:
1. While pressing the [AUTO CALL] and [A.F.D] buttons, press
the [
] button to turn on the main power.
?/1
2. The message “SWP. ALL” appears.
SHIPMENT MODE
All preset contents are cleared when this mode is activated. Use
this mode before returning the product to clients upon completion
of repair.
Procedure:
1. While pressing the [AUT O CAL] and [MUSIC] buttons, press the
] button to turn on the main power.
[
?/1
2. The message “CLEARING” appears.
DCAC FACTORY TEST MODE
DCAC Factory Test mode have two stages:
1. DCAC DSP Data Line Checking
2. DCAC board Checking
StartPassPass
DSP Data Line
Check
Auto Cal Mic
Check
] button counts
END
7. Turn the [INPUT SELECTOR] dial once again. All segments
turn off.
8. Every turning of the [INPUT SELECTOR] dial turns on each
segment one after another on the same order.
S.F. CLEAR MODE
The preset sound fi led is cleared when this mode is activated. Use
this mode before returning the product to clients upon completion
of repair.
Procedure:
1. While pressing the [2CH] button, press the [
] button to turn
?/1
on the main power.
2. The message “S.F CLR.” appears and initialization is performed.
VERSION CHECK MODE
When this mode is used the model, the destination and the software
version number are displayed.
Procedure:
1. While pressing the [AUTO CAL] and [DISPLAY] buttons, press
the [
] button to turn on the main power.
?/1
2. The model, the distination and the software version number
appear.
Factory Test System Setup
Receiver
DCAC MIC
SPK Front Left
1. When power off :
While pressing the [MEMORY/ENTER] and [MOVIE] but-
tons, press the [
] button to turn on the main power .
?/1
“DCAC FTM” appears.
Afterward, press the [TUNING MODE] to start DCAC factory
test mode.
12
Page 13
SECTION 5
ELECTRICAL CHECK
STR-KM5000
1. DCAC DSP Data Line Checking
After press the [TUNING MODE] button, DCAC Factory test
mode will start, below display will show:
“DCAC x” x = 1, 2, 3, 4
If there is error happen, below display will show:
“ERR SD0x” x = 1 → D1501 or R1530 problem
x = 2 → D1502 problem
x = 3 → D1503 problem
x = 4 → D1504 problem
2. DCAC board Checking
Connect front left speaker of the receiver and AUTO CAL microphone. Turn [MASTER VOLUME] jog, there will be test tone
sound output from front left speaker, and the display will change
accordingly.
“AD - xxx” xxx = 0 to 255 (depends on loudness of test tone)
RE-BOX CLASSIFICATION TEST MODE
Procedure:
1. While pressing the [MEMORY/ENTER] and [INPUTMODE]
buttons, press the [
2. The message “R.BOX[][][]XX” appears.
XX: times set powered on
VACS CONTROL TEST MODE
The VACS feature of the amplifi er is turned off purposely.
Procedure:
1. While pressing the [MEMORY/ENTER] and [2CH] buttons,
press the [
2. The message “VACS OFF” appears.
] button to turn on the main power.
?/1
] button to turn on the main power.
?/1
FM AUTO STOP CHECK
signal
generator
set
Procedure:
1. Turn on the set.
2. Input the following signal from signal generator to FM antenna
input directly.
Carrier frequency : A = 87.5 MHz, B = 98 MHz, C = 108 MHz
Deviation : 75 kHz
Modulation : 1 kHz
ANT input : 1 kHz
Note: Use 75 ohm coaxial cable to connect signal generator and the set.
You cannot use video cable for checking.
Use signal generator whose output impedance is 75 ohm.
3. Set to FM tuner function and scan the input FM signal with
automatic scanning.
4. Confi rm that input frequency of A, B and C are detected and
automatic scanning stops.
When the station signal is received in good condition, automatic
scanning stops.
STR-KM5000
1313
Page 14
STR-KM5000
STR-KM5000
1414
6-1. BLOCK DIAGRAM - MAIN Section -
SECTION 6
DIAGRAMS
EEPROM
IC1131
SYSTEM CONTROLLER
IC1101 (1/5)
DIGITAL OPTICAL
RECEIVER
IC1352
DIR_DO
DIR_DI
DIR_CLK
DIR_CE
DIR_ERROR
DIR_XMODE
DIR_XSTATE
DIR_DATA0
1
DATA0, BCK
LRCK, CKOUT
DOUT
7
SCKI
12
BCK
8
LRCK
13
VINL
14
VINR
6
XMCK
20
DATAO
16
BCK
14
LRCK
15
CKOUT
13
AUDIO
24
47
OPTICAL
BD IN
OPTICAL
SAT IN
DIGITAL OPTICAL
RECEIVER
IC1351
WAVE
SHAPER
IC1303
DIGITAL AUDIO
INTERFACE RECEIVER
IC1301
DIN2
J1301
5
COAXIAL
DVD IN
DIGITAL
A/D CONVERTER
IC1401
21
22
X1301
12.288MHz
XOUT
XIN
DIR_CKCEL1
94
D1301
83
82
X1
X0
29
SDA
30
SCL
X1101
24MHz
A
• SIGNAL PATH
: AUDIO (ANALOG)
: AUDIO (DIGITAL)
• R-ch is omitted due to same as L-ch.
DIN1
4
DIN0
3
CKSEL1
DOUTDICLKCEXMODE
XSTATE
ERROR
AUDIO
A_AUDIO
D_AUDIO
D
C
B
ERR
E
98 97 95 9699
100
93
R-CH
35 36 38 37 48 17 34
BD IN
VIDEO 1
VIDEO IN
VIDEO 2 IN/
PORTABLE A V IN
VIDEO
DVD
VIDEO IN
SAT
VIDEO IN
J210 (1/2)
J211 (1/2)
J298 (1/2)
VIDEO 1
VIDEO OUT
MONITOR
VIDEO OUT
J210 (2/2)
J220 (1/2)
J221
J211 (2/2)
VIDEO AMP
IC210
VIN1
13
VIN5
3
VIN4
5
VIN2
9
VOUT1
1
VOUT2
15
SW114SW210SW34SW46SW5
2
5
V_SW16V_SW27V_SW39V_SW4
D211
D210
: VIDEO
COMPONENT
VIDEO
VIDEO AMP
IC220
CH1 IN1
1
CH2 IN1
8
CH3 IN1
17
CH1 IN2
3
CH2 IN2
14
CH3 IN2
15
CH1 IN3
5
CH2 IN3
12
CH3 IN3
13
SW12SW2
4PS23
4
COMP_S13COMP_S22V-MUTE
PB/CB
Y
P
R/CR
DVD IN
P
B/CB
Y
P
R/CR
SAT IN
P
B/CB
Y
P
R/CR
J220 (2/2)
CH1 OUT
24
CH2 OUT
22
CH3 OUT
20
P
B/CB
Y
P
R/CR
COMPONENT
VIDEO
MONITOR OUT
(Page 16)
(Page 16)
(Page 17)
(Page 16)
(Page 16)
Page 15
STR-KM5000
STR-KM5000
1515
6-2. BLOCK DIAGRAM - HDMI Section -
• SIGNAL PATH
:VIDEO
SYSTEM CONTROLLER
IC1101 (2/5)
CN5001
HDMI
DVD IN
A24
77
B24
76
1
3
A23
74
B23
73
4
6
A22
71
B22
70
7
9
A21
68
B21
67
10
DATA2+
DATA2–
DATA1+
DATA1–
DATA0+
DATA0–
CLOCK+
CLOCK–
SCL (5V)
SDA (5V)
+5V POWER
18
12
15
16
21
S1
HDMI RECIVER/TRANSCEIVER
IC5001
34
I2C_SDA(HDMI)/S1
42
OEB
86
HDMI_RESET
SCL2
64
HOT PLUG DET
19
HPD2
62
HOT PLUG DET
19
HPD1
80
SDA2
63
CN5002
HDMI
BD IN
A14
15
B14
14
1
3
A13
12
B13
11
4
6
A12
9
B12
8
7
9
A11
6
B11
5
10
DATA2+
DATA2–
DATA1+
DATA1–
DATA0+
DATA0–
CLOCK+
CLOCK–
SCL (5V)
SDA (5V)
+5V POWER
18
12
15
16
SCL1
3
SDA1
2
88
HDMI_DET
LEVEL SHIFT
IC5004
ANALOG SWITCH
IC5005
CN5003
HDMI OUT
Y4
25
Z4
26
1
3
Y3
28
Z3
29
4
6
Y2
31
Z2
32
7
9
Y1
34
Z1
35
10
HPD_SINK
DATA2+
DATA2–
DATA1+
DATA1–
DATA0+
DATA0–
CLOCK+
CLOCK–
SCL (5V)
SDA (5V)
HOT PLUG DET
4019
12
15
16
+5V POWER
18
SCL_SINK
38
SDA_SINK
39
87
+5V_CTRL(HDMI)
+5.8V
REGULATOR
IC5006
+3.3V
REGULATOR
IC5003
HDMI+9.5VHDMI +3.3V
+5V
REGULATOR
IC5002
: AUDIO (DIGITAL)
Page 16
STR-KM5000
STR-KM5000
1616
6-3. BLOCK DIAGRAM - DSP Section -
A
B
DATA0, BCK, LRCK, CKOUT
LRCK
DATA0
CKOUT
BCK
• SIGNAL PATH
D_AUDIO
D
DCAC_IN
38
SYSTEM CONTROLLER
IC1101 (3/5)
SWITCH
IC1014
78 DPSIA
79 DPSIB
88 DPLRCK
94 DPFSCK
89 DPBCK
16 FLAG1
DSP SPDIF(LAT)
21
XRST
8
DSP INT
47
XSPIDS
XRESET
FLAG0
DSP
IC1501
D/A CONVERTER
IC1452
2MCK
3BCK
4 LRCK
9 DIN3
7 DIN1
8 DIN2
10 DIN4
VO1L
21
VO1R
22
VO2L 23
VO2R
24
VO3L
25
VO3R
26
DPDVLRCK
64
DPDVBCK
DPSOA
DPSOB
DSPOC
DSPOD
87
65
70
71
86
DSP SPI CLK
: AUDIO (ANALOG)
: AUDIO (DIGITAL)
143
142
X1302
25MHz
XTAL
CLKIN
97 XNONAUDIO
E
AUDIO
ERR
122
121
15
20
MOSI
19
MISO
18
SPICLK
MOSI
MISO
125
127 126
DAC_ML
12
DAC_MC
13
DCAC_INT
57
DAC_MDI
14
DAC_MUTE
15
11
13
14
ML/I2S
MD/DM
MUTE
12
MC/IWL
LINE AMP
IC1404
LINE AMP
IC1405
LINE AMP
IC1406
R-CH
R-CH
SL
L, C, SW, SL, SBL
C
L
VO4L 19
LINE AMP
IC1403
SBL
SW
F
• R-ch is omitted due to same as L-ch.
AUTO
CAL MIC
J2000
MIC AMP
IC2000
D1502
D1503
D1504
D1501
CLINK_RX
CLINK_TX
6
5
CN1302 (1/2)
27
FLASH2/
DMPORT_MICOM RX
FLASH1/
DMPORT_MICOM TX
28
DET
7
26
DMPORT_DET
DMPORT
(Page 14)
(Page 14)
(Page 14)
(Page 14)
(Page 17)
Page 17
STR-KM5000
STR-KM5000
1717
6-4. BLOCK DIAGRAM - AUDIO Section -
SYSTEM CONTROLLER
IC1101 (4/5)
10
DATA11CLK
L CH
R CH
DO
DI
INL1 (TUNER_L)
63
VOL_IC_CLK
25
VOL_IC_DATA
24
89
LOUT
76
FM 75Ω
COAXIAL
91
90
92
DVD
AUDIO IN
ANTENNA
TUNER (FM/AM)
AM
INL2 (DMPORT_L)
61
L+
R+
14
13
CN1302 (1/2)
R-CH
INPUT SELECTOR,
ELECTRICAL VOLUME
IC400
R-CH
FM ANT
GND
AM ANT
GND
CLOCK
CE
DO/SD/ST
TUNER_DATA
TUNER_CLK
SLATCH
INL9
47
INL7
51
TV IN
J401 (1/2)
SA-CD/CD
CD-R IN
L
R
L
R
R-CH
R-CH
INL12
41
INL11
43
J403
SAT
AUDIO IN
L
R
L
R
R-CH
R-CH
VIDEO 2 IN/
PORTABLE A V IN
AUDIO
INL5
55
SLIN
68
CIN
70
SWIN
71
LIN
72
J298 (2/2)
L
RR-CH
BUFFER
IC3002
LINE AMP
IC2101
43
SD
TUNER_SD
• SIGNAL PATH
: TUNER
: AUDIO (ANALOG)
• R-ch is omitted due to same as L-ch.
A_AUDIO
C
DMPORT
VIDEO 1
AUDIO IN
INL13
38
J404 (1/2)
L
RR-CH
FLOUT
14
P_DET
G
SL
L, C, SW, SL, SBL
C
L
SW
F
SBLIN
66
SBL
RECL1
29
J401 (2/2)
L
R
SA-CD/CD
CD-R OUT
R-CH
RECL2
27
J404 (2/2)
L
R
VIDEO 1
AUDIO OUT
R-CH
+VOUT1
2
NF1
5
-VOUT1
3
LIMITER
Q701, 702
BOOSTER
Q703
BOOSTER
Q704
CURRENT
DETECT
Q711, 712
IN1
6
POWER AMP
IC700
AF POWER
PROTECT
Q720
RELAY DRIVE
Q375
RELAY DRIVE
Q350
RELAY DRIVE
Q360
RELAY DRIVE
Q355
PROTECTOR
61
67 70
VACS CTRL
45
PROTECT
SWITCH
Q320, 321,
323 – 325
SLOUT
18
+VOUT1
2
NF1
5
-VOUT1
3
LIMITER
Q801, 802
BOOSTER
Q803
BOOSTER
Q804
CURRENT
DETECT
Q811, 812
IN1
6
POWER AMP
IC800
+VOUT1
2
NF1
5
-VOUT1
3
LIMITER
Q601, 602
BOOSTER
Q653
BOOSTER
Q604
IN1
6
AF POWER
PROTECT
Q820
COUT
16
+VOUT2
12
NF2
9
-VOUT2
11
LIMITER
Q651, 652
BOOSTER
Q653
BOOSTER
Q654
CURRENT
DETECT
Q661, 662
IN2
8
POWER AMP
IC600
MONO-SW_OUT
12
MONO-SW_OUT
10
MONO-SW_IN
13
MONO-SW_IN
11
SW-L_OUT
3SW-L_IN
4
ANALOG AUDIO SWITCH
IC2100
AF POWER
PROTECT
Q670
CURRENT
DETECT
Q611, 612
AUDIO ON/OFF
CONTROL
Q2101
AUDIO ON/OFF
CONTROL
Q2100
AF POWER
PROTECT
Q620
SBLOUT
20
SWOUT
15
+
−
+
−
RY355
RY360
RY350
RY375
R-CH
R-CH
+
−
+
−
+
−
R-CH
R-CH
+
−
HP_DETECT
HP_RY
FRONT A
C/SW/REAR/SB_RY
55 62
FRONT A RY
66
D1110
D1109
D1108
D1107
RELAY DRIVE
Q2103
RY2101
J790
PHONES
TB601
L
R
FRONT
TB605
L
R
L
R
L
R
SURROUND
SURROUND
BACK
SPEAKERS
TB607
CENTER
J406
SUB WOOFER
AUDIO OUT
15A5
B
6C14
D
R-CH
(Page 16)
(Page 14)
(Page 18)
Page 18
STR-KM5000
STR-KM5000
1818
6-5. BLOCK DIAGRAM - POWER SUPPLY Section -
(AC IN)
F901
JS903
B+
B-
POWER AMP -45V
FL -20V
TU +9V
VIDEO +5V
DSP +3.3V
DSP +1.2V
A+3.3V
DMPORT +5V
VIDEO -5V
A-7V
A+5V
A+7V
SYS +3.3V
58
POWER_RY
63FUSE_DETECT
SYSTEM CONTROLLER
IC1101 (5/5)
75
FL_DATA
74
FL_CLK
76
FL LAT
FLUORESCENT
INDICATOR TUBE DRIVER
IC100
7
DIN
8
CLK
9
STB
FLUORESCENT
INDICATOR
TUBE
FL101
SEG1 – SEG16,
SEG17
14 – 29, 31
GRID1 – GRID11
42 – 32
54
SIRCS
ROTARY
ENCODER
RV101
LED
DRIVE
Q110
LEVEL SHIFT
IC101
REMOTE CONTROL
RECEIVER
IC103
INPUT
SELECTOR
I/
S109 – 113, 115
58
POWER KEY
1
SW1
39
A/D1
S101 – 108
40
A/D2
32
31
ENC_A
S100
ENC_B
ROTARY
ENCODER
RV102
MASTER
VOLUME
65
64
VOL_ENCODER(B)
VOL_ENCODER(A)
ROTARY
ENCODER
RV103
– TUNING +
60
59
TUNING_A
TUNING_B
G
48STOP
P_DET
SUB POWER
TRANSFORMER
T902 (Except Mexican)
T903 (Mexican)
(Mexican)
Singapore,
Malaysia,
Argentina, Thai
RELAY DRIVE
Q901
RECT
D950 – 953
RECT
D910 – 913
RECT
D921
AC OFF DETECT
Q990
RY901
D990, 991
+3.3V
REGULATOR
IC1904
+5V
REGULATOR
IC201
+9V
REGULATOR
IC1902
+5V
REGULATOR
IC4001
+7V
REGULATOR
IC350
-20V
REGULATOR
Q930
B- SWITCH
Q500, 501
+5V
REGULATOR
IC1001
+3.3V
REGULATOR
IC1903
+5V
REGULATOR
IC1906
+3.3V
REGULATOR
IC1905
+1.2V
REGULATOR
IC1002
MAIN POWER
TRANSFORMER
T901
PROTECT DETECT
IC565
RECT
D4001
-5V
REGULATOR
IC202
-7V
REGULATOR
IC352
F4002
F4001
FL+5V
+5V
REGULATOR
IC1031
HDMI+9.5V
D105
(MULTI CHANNEL DECODEING)
RECT
D941, 942
120V
S901
220V
240V
VOLTAGE
SELECTOR
(Chilian, Peruvian)
JS901
JS902
1
2
3
(Page 17)
Ver. 1.1
Page 19
STR-KM5000
STR-KM5000
1919
For Schematic Diagrams.
Note:
• All capacitors are in μF unless otherwise noted. (p: pF)
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise
specifi ed.
• f : internal component.
• 2 : nonfl ammable resistor.
• 5 : fl usible resistor.
• C : panel designation.
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is printed in each block.)
• A : B+ Line.
• B : B– Line.
• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
no mark : TUNER
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production
tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production
tolerances.
• Circled numbers refer to waveforms.
• Signal path.
J : AUDIO (DIGITAL)
F : AUDIO (ANALOG)
f : TUNER
E : VIDEO
• Abbreviation
AR : Argentina model
E51 : Chilean and Peruvian models
MX : Mexican model
MY : Malaysia model
SP : Singapore model
For Printed Wiring Boards.
Note:
• X : Parts extracted from the component side.
• Y : Parts extracted from the conductor side.
• f : Internal component.
• : Pattern from the side which enables seeing.
(The other layers' patterns are not indicated.)
• Indication of transistor.
CEB
These are omitted.
Caution:
Parts face side:
(SIDE A)
Pattern face side:
(SIDE B)
Parts on the parts face side seen from
the pattern face are indicated.
Parts on the pattern face side seen from
the parts face are indicated.
• Circuit Boards Location
Caution:
Pattern face side:
(Conductor Side)
Pattern face side:
(Component Side)
Parts on the pattern face side seen from
the pattern face are indicated.
Parts on the parts face side seen from
the parts face are indicated.
Note: The components identifi ed by mark 0 or dotted
• IC Pin Function Description
DIGITAL AB BOARD IC1101 MB90F046PF-G-117E1 (SYSTEM CONTROLLER)
Pin No.Pin NameI/ODescription
1DIR_DATA0ISerial data input from the digital audio interface receiver
2V-MUTEOMuting signal output to the video amplifi er
3, 4COMP_S1, COMP_S2OComponent video select signal output to the video amplifi er
5 to 7V_SW1 to V_SW3OVideo select signal output to the video amplifi er
8XRSTOSystem reset signal output to the DSP
9V_SW4OVideo select signal output to the video amplifi er
10NC-Not used
11VSS-Ground terminal
12DAC_MLOSerial data latch pulse signal output to the D/A converter
13DAC_MCOClock signal output to the D/A converter
14DAC_MDIOSerial data output to the D/A converter
15DAC_MUTEOMuting signal output to the D/A converter
16, 17NC-Not used
18MISOISerial data input from the DSP
19MOSIOSerial data output to the DSP
20DSP SPI CLKOSerial data transfer clock signal output to the DSP
21DSP SPIDS(LAT)OSerial data latch pulse signal output to the DSP
22NC-Not used
23VCC5-Power supply terminal (+3.3V)
24VOL_IC_DATAOSerial data output to the input selector, electrical volume
25VOL_IC_CLKOClock signal output to the input selector, electrical volume
26DMPORT_DETIDMPORT adapter connection detection signal input terminal
27
28
29SDAISerial data input from the EEPROM
30SCLOSerial data transfer clock signal output to the EEPROM
31ENC_AIJog dial pulse input from the rotary encoder (for INPUT SELECTOR) (A phase input)
32ENC_BIJog dial pulse input from the rotary encoder (for INPUT SELECTOR) (B phase input)
33I2C_SCL(HDMI)/NCONot used
34I2C_SDA(HDMI)/S1OHDMI select signal output to the HDMI reciever/transciever
35AVCC-Analog power supply terminal (+3.3V) (for A/D converter)
36AVRH-Reference voltage input terminal (+3.3V) (for A/D converter)
37AVSS-Analog ground terminal (for A/D converter)
38DCAC_INIAUTO CAL MIC signal input terminal
41VERSIONISetting terminal for the destination
42VSS-Ground terminal
43TUNE SDITuning detection signal input from the tuner (FM/AM)
44MODELISetting terminal for the model
45VACS CTRLIVACS control signal input terminal
46NC-Not used
47DSP INTIInterrupt status input from the DSP
48STOPIAC off detection signal input terminal "L": AC off
49MD0ICPU operation mode setting signal input terminal "H": fl ash programming
50MD1ICPU operation mode setting signal input terminal Not used
51MD2ICPU operation mode setting signal input terminal "H": fl ash programming
52RDS_CLKIRDS clock data input terminal Not used
53RDS_DATAIRDS serial data input terminal Not used
54SIRCSISIRCS signal input from the remote control receiver
55HP_DETECTIHeadphone detection signal input terminal "H": headphone is connected
56POWER KEYIPower key input terminal
57DCAC_INTIDCAC data input from the DSP
FLASH2/DMPORT_MI-
COM RX
FLASH1/DMPORT_MI-
COM TX
Flash programming signal input terminal
I/O
Transmit data output to the DMPORT connector
Flash programming signal output terminal
I/O
Receive data input from the DMPORT connector
46
Page 47
STR-KM5000
Pin No.Pin NameI/ODescription
58POWER_RYO Relay drive signal (for main power) output terminal "H": relay on
59TUNING_AIJog dial pulse input from the rotary encoder (for - TUNING +) (A phase input)
60TUNING_BIJog dial pulse input from the rotary encoder (for - TUNING +) (B phase input)
61PROTECTORIProtector status detect signal input terminal
62HP_RYORelay drive signal (for headphone) output terminal "H": relay on
63FUSE_DETECTIFuse detection signal input terminal
64VOL_ENCODER(B)IJog dial pulse input from the rotary encoder (for MASTER VOLUME) (B phase input)
65VOL_ENCODER(A)IJog dial pulse input from the rotary encoder (for MASTER VOLUME) (A phase input)
66C/SW/REAR/SB_RYORelay drive signal (for center, surround, surround back) output terminal "H": relay on
67
68DC-CONTROL-Not used
69SW_RYORelay drive signal (for subwoofer) output terminal "H": relay on
70FRONT A RYORelay drive signal (for front A) output terminal "H": relay on
71 to 73NC-Not used
74FL_CLKOSerial data transfer clock signal output to the fl uorescent indicator tube
75FL_DATAOSerial data output to the fl uorescent indicator tube
76FL_LATOStrobe signal output to the fl uorescent indicator tube
77RSTXIReset signal input from the reset signal buffer
78NC-Not used
79X0AISub system clock input terminal Not used
80X1AOSub system clock output terminal Not used
81VSS-Ground terminal
82X0IMain system clock input terminal (24 MHz)
83X1OMain system clock output terminal (24 MHz)
84VCC3-Power supply terminal (+3.3V)
85+5.8V_CTRL(HDMI)-Not used
86RESET_HDMIOSystem reset signal output to the HDMI reciever/transciever
87+V_CTRL(HDMI)O HDMI control signal output to the HDMI reciever/transciever
88HDMI_DETIHeadphone detection signal input from the HDMI reciever/transciever
89DO/SD/STIPLL data input from the tuner (FM/AM)
90TUNER_CLKOSerial data transfer clock signal output to the tuner (FM/AM)
91TUNE_DATAOSerial data output to the tuner (FM/AM)
92SLATCHOSerial data latch pulse signal output to the tuner (FM/AM)
93DIR_XMODEOReset signal output to the digital audio interface receiver "L": reset
94DIR_CKSEL1OClock selection signal output to the digital audio interface receiver
95DIR_CLKOSerial data transfer clock signal output to the digital audio interface receiver
96DIR_CEOChip enable signal output to the digital audio interface receiver
97DIR_DIOSerial data output to the digital audio interface receiver
98DIR_DOISerial data input from the digital audio interface receiver
99DIR_ERRORIPLL lock error signal and data error fl ag input from the digital audio interface receiver
100DIR_XSTATEISource clock selection monitor input from the digital audio interface receiver
FRONT B RY/
ST SW RY
ORelay drive signal (for front B) output terminal "H": relay on
47
Page 48
STR-KM5000
DIGITAL AB BOARD IC1501 ADSST-AVR-1115 (DSP)
Pin No.Pin NameI/ODescription
1VDDINT-Power supply terminal (+1.2V)
2, 3
4, 5
6GND-Ground terminal
7VDDEXT-Power supply terminal (+3.3V)
8GND-Ground terminal
9VDDINT-Power supply terminal (+1.2V)
10GND-Ground terminal
11VDDINT-Power supply terminal (+1.2V)
12GND-Ground terminal
13VDDINT-Power supply terminal (+1.2V)
14GND-Ground terminal
15FRAG0OInterrupt status output to the system controller
16FRAG1IPLL lock error signal and data error fl ag input terminal
17AD7I/OTwo-way data bus and address signal output with S-RAM Not used
18GND-Ground terminal
19VDDINT-Power supply terminal (+1.2V)
20GND-Ground terminal
21VDDEXT-Power supply terminal (+3.3V)
22GND-Ground terminal
23VDDINT-Power supply terminal (+1.2V)
24 to 26AD6 to AD4I/OTwo-way data bus and address signal output with S-RAM Not used
33, 34AD1, AD0I/OTwo-way data bus and address signal output with S-RAM Not used
35XWROData write enable signal output to the S-RAM "L": active Not used
36, 37VDDINT-Power supply terminal (+1.2V)
38GND-Ground terminal
39XRDORead strobe signal output to the S-RAM "L": active Not used
40ALEOAddress latch enable signal output terminal Not used
41 to 43AD15 to AD13I/OTwo-way data bus and address signal output with S-RAM Not used
44GND-Ground terminal
45VDDEXT-Power supply terminal (+3.3V)
46AD12I/OTwo-way data bus and address signal output with S-RAM Not used
47VDDINT-Power supply terminal (+1.2V)
48GND-Ground terminal
49 to 52AD11 to AD8I/OTwo-way data bus and address signal output with S-RAM Not used
53A16OAddress signal output to S-RAM Not used
54VDDINT-Power supply terminal (+1.2V)
55GND-Ground terminal
56, 57A17, A18OAddress signal output to S-RAM Not used
58GND-Ground terminal
59VDDEXT-Power supply terminal (+3.3V)
60VDDINT-Power supply terminal (+1.2V)
61GND-Ground terminal
62PF_CEI/OChip enable signal input/output terminal Not used
63SPI_MASOMaster/slave selection signal output terminal "L": DSP is master Not used
64DPSOAOPCM audio signal (front L/R) output to the D/A converter
65DPSOBOPCM audio signal (surround L/R) output to the D/A converter
66VDDINT-Power supply terminal (+1.2V)
CLKCFG0,
CLKCFG1
BOOTCFG0,
BOOTCFG1
IClock frequency setting terminal
IBoot mode setting terminal for DSP
48
Page 49
STR-KM5000
Pin No.Pin NameI/ODescription
67GND-Ground terminal
68VDDINT-Power supply terminal (+1.2V)
69GND-Ground terminal
70DPSOCOPCM audio signal (center, sub woofer) output to the D/A converter
71DPSODOPCM audio signal (surround back L/R) output to the D/A converter
72VDDINT-Power supply terminal (+1.2V)
73VDDEXT-Power supply terminal (+3.3V)
74GND-Ground terminal
75VDDINT-Power supply terminal (+1.2V)
76GND-Ground terminal
77DPSOEOPCM audio signal output terminal Not used
78DPSIAIPCM audio signal (digital input) input from the digital audio interface receiver
79DPSIBIPCM audio signal (front L/R) input from the A/D converter
80DPSICIPCM audio signal (surround L/R) input terminal Not used
81DPSIDIPCM audio signal (center, sub woofer) input terminal Not used
82DPSIEIPCM audio signal (surround back L/R) input terminal Not used
83VDDINT-Power supply terminal (+1.2V)
84, 85GND-Ground terminal
86DPDVLRCKOL/R sampling clock signal output to the D/A converter for PCM audio output
87DPDVBCKOBit clock signal output to the D/A converter for PCM audio output
88DPLRCKIL/R sampling clock signal input terminal for PCM audio input
89DPBCKIBit clock signal input terminal for PCM audio input
90VDDINT-Power supply terminal (+1.2V)
91, 92GND-Ground terminal
93VDDEXT-Power supply terminal (+3.3V)
94DPFSCKIMaster clock signal input terminal
95GND-Ground terminal
96VDDINT-Power supply terminal (+1.2V)
97XNONAUDIOIDigital input signal switch control signal input from the digital audio interface receiver
98XSF_CEOChip enable signal output terminal Not used
119GND-Ground terminal
120VDDINT-Power supply terminal (+1.2V)
121XRESETISystem reset signal input from the system controller
122XSPIDSISerial data latch pulse signal input from the system controller
123GND-Ground terminal
124VDDINT-Power supply terminal (+1.2V)
125SPICLKI/OSerial data transfer clock signal input/output with the system controller
49
Page 50
STR-KM5000
Pin No.Pin NameI/ODescription
126MISOOSerial data output to the main system controller
127MOSIISerial data input from the main system controller
128GND-Ground terminal
129VDDINT-Power supply terminal (+1.2V)
130VDDEXT-Power supply terminal (+3.3V)
131AVDD-Power supply terminal (+3.3V)
132AVSS-Ground terminal
133GND-Ground terminal
134CLKOUT-Not used
135XEMU-Not used
136TDO-Not used
137TDI-Not used
138CTRST-Not used
139TCK-Not used
140TMS-Not used
141GND-Ground terminal
142CLKINISystem clock input terminal (25 MHz)
143XTALOSystem clock output terminal (25 MHz)
144VDDEXT-Power supply terminal (+3.3V)
1NC-Not used
2SDA1I/OI2C two-way data bus with the HDMI BD IN jack
3SCL1II2C clock signal input from the HDMI BD IN jack
4GND-Ground terminal
5B11ITMDS clock signal (negative) input from the HDMI BD IN jack
6A11ITMDS clock signal (positive) input from the HDMI BD IN jack
7VCC-Power supply terminal (+3.3V)
8B12ITMDS data (negative) input from the HDMI BD IN jack
9A12ITMDS data (positive) input from the HDMI BD IN jack
10GND-Ground terminal
11B13ITMDS data (negative) input from the HDMI BD IN jack
12A13ITMDS data (positive) input from the HDMI BD IN jack
13VCC-Power supply terminal (+3.3V)
14B14ITMDS data (negative) input from the HDMI BD IN jack
15A14ITMDS data (positive) input from the HDMI BD IN jack
16GND-Ground terminal
17VCC-Power supply terminal (+3.3V)
18VSADJITMDS compliant voltage swing control signal input terminal Not used
19PREIOutput de-emphasis setting terminal "L": 0 dB, "H": 3 dB Fixed at "L" in this set
20NC-Not used
21S1ISource selection signal input from the system controller
22, 23S2, S3ISource selection signal input terminal Not used
24GND-Ground terminal
25Y4OTMDS data (positive) output to the HDMI OUT jack
26Z4OTMDS data (negative) output to the HDMI OUT jack
27VCC-Power supply terminal (+3.3V)
28Y3OTMDS data (positive) output to the HDMI OUT jack
29Z3OTMDS data (negative) output to the HDMI OUT jack
30GND-Ground terminal
31Y2OTMDS data (positive) output to the HDMI OUT jack
32Z2OTMDS data (negative) output to the HDMI OUT jack
33VCC-Power supply terminal (+3.3V)
34Y1OTMDS data (positive) output to the HDMI OUT jack
35Z1OTMDS data (negative) output to the HDMI OUT jack
36, 37GND-Ground terminal
38SCL_SINKOI2C clock signal output to the HDMI OUT jack
39SDA_SINKI/OI2C two-way data bus with the HDMI OUT jack
40HPD_SINKIHot plug detection signal input from the HDMI OUT jack
41NC-Not used
42OEBIChip enable signal input from the system controller
43VCC-Power supply terminal (+3.3V)
44 to 46HPD3, SDA3, SCL3-Not used
47GND-Ground terminal
48, 49B31, A31-Not used
50VCC-Power supply terminal (+3.3V)
51, 52B32, A32-Not used
53GND-Ground terminal
54, 55B33, A33-Not used
56VCC-Power supply terminal (+3.3V)
57, 58B34, A34-Not used
59GND-Ground terminal
60NC-Not used
61VCC-Power supply terminal (+3.3V)
62HPD2OHot plug detection signal output to the HDMI DVD IN jack
63SDA2I/OI2C two-way data bus with the HDMI DVD IN jack
STR-KM5000
51
Page 52
STR-KM5000
Pin No.Pin NameI/ODescription
64SCL2II2C clock signal input from the HDMI DVD IN jack
65GND-Ground terminal
66B21ITMDS clock signal (negative) input from the HDMI DVD IN jack
67A21ITMDS clock signal (positive) input from the HDMI DVD IN jack
68VCC-Power supply terminal (+3.3V)
69B22ITMDS data (negative) input from the HDMI DVD IN jack
70A22ITMDS data (positive) input from the HDMI DVD IN jack
71GND-Ground terminal
72B23ITMDS data (negative) input from the HDMI DVD IN jack
73A23ITMDS data (positive) input from the HDMI DVD IN jack
74VCC-Power supply terminal (+3.3V)
75B24ITMDS data (negative) input from the HDMI DVD IN jack
76A24ITMDS data (positive) input from the HDMI DVD IN jack
77GND-Ground terminal
78NC-Not used
79VCC-Power supply terminal (+3.3V)
80HPD1OHot plug detection signal output to the HDMI BD IN jack
52
Page 53
Note:
• -XX and -X mean standardized parts, so
they may have some difference from the
original one.
• Items marked “*” are not stocked since
they are seldom required for routine service.
Some delay should be anticipated when
ordering these items.
7-1. FRONT PANEL SECTION
SECTION 7
EXPLODED VIEWS
• The mechanical parts with no reference
number in the exploded views are not supplied.
• Color Indication of Appearance Parts Example:
KNOB, BALANCE (WHITE) . . . (RED)
R R
Parts Color Cabinet’s Color
STR-KM5000
Ver. 1.1
• Abbreviation
AR : Argentina model
E51 : Chilean and Peruvian models
MX : Mexican model
MY : Malaysia model
SP : Singapore model
TH : Thai model
The components identifi ed by mark 0
or dotted line with mark 0 are critical for
safety.
Replace only with part number specifi ed.
#1
not supplied
(DCAC board)
3
4
2
1
not supplied
(POWER board)
not supplied
(HEADPHONE
board)
"
supplied with
RV101, RV103
supplied with
RV102
5
#
not supplied
(VIDEO 2 board)
5
4
RV103
not
supplied
not supplied
#1
%
9
5
5
$
8
(E51)
not supplied
(AC SELECT board)
'
RV101
5
RV102
#1
8
7
6
&
10
7
back panel section
#1
#1
#1
7
#1
"
#1
'
$
&
#
%
main section
Note: If wire (fl at type) is replaced, install it after bending
it in the same form as that before replacement.
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
1 2-661-142-01 VOLUME KNOB
2 X-2190-020-1 KNOB MENU ASSY
3 X-2188-072-2 FRONT PANEL ASSY
4 4-977-358-01 CUSHION
5 3-087-053-01 +BVTP2.6 (3CR)
Note: If wire (fl at type) is replaced, install it after bending
it in the same form as that before replacement.
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
51 A-1519-237-A HDMI SW BOARD, COMPLETE
52 1-828-299-51 WIRE (FLAT TYPE) (7 CORE)
0 53 1-777-071-83 CORD, POWER (E51, SP, MY)
0 53 1-829-387-11 CORD, POWER (AR)
0 53 1-829-627-11 POWER-SUPPLY CORD (MX)
0 53 1-843-288-21 POWER-SUPPLY CORD (TH)
54 4-966-267-12 BUSHING (FBS001), CORD
55 A-1444-791-A DIGITAL AB BOARD, COMPLETE (SP, MY)
55 A-1444-792-A DIGITAL AB BOARD, COMPLETE (AR)
55 A-1444-793-A DIGITAL AB BOARD, COMPLETE (TH)
55 A-1444-794-A DIGITAL AB BOARD, COMPLETE (E51)
55 A-1550-087-A DIGITAL AB BOARD, COMPLETE (MX)
56 1-827-733-51 WIRE (FLAT TYPE) (7 CORE)
57 1-828-951-11 WIRE (FLAT TYPE) (9 CORE)
0 T901 1-443-523-11 POWER TRANSFORMER (MX)
0 T901 1-443-525-11 POWER TRANSFORMER (SP, MY, AR, TH)
0 T901 1-443-526-11 POWER TRANSFORMER (E51)
#1 7-685-646-79 SCREW +BVTP 3X8 TYPE2 IT-3
Note: TRANSISTOR (MN2488-OPY-MK/MP1620-OPY-MK)
include MICA SHEET.
55
Page 56
STR-KM5000
Ver. 1.1
AC SELECT
DCAC
ELECTRICAL PARTS LIST
DCDC CONVERTER
Note:
• Due to standardization, replacements in
the parts list may be different from the
parts specifi ed in the diagrams or the com-
ponents used on the set.
• -XX and -X mean standardized parts, so
they may have some difference from the
original one.
• Items marked “*” are not stocked since
they are seldom required for routine service.
Some delay should be anticipated when
ordering these items.
• CAPACITORS
uF: μF
• COILS
uH: μH
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
AC SELECT BOARD (E51)
A-1444-791-A DIGITAL AB BOARD, COMPLETE (SP, MY)
A-1444-792-A DIGITAL AB BOARD, COMPLETE (AR)
A-1444-794-A DIGITAL AB BOARD, COMPLETE (E51)
A-1550-087-A DIGITAL AB BOARD, COMPLETE (MX)
*************************
IC1001 8-759-231-53 IC TA7805S
IC1002 6-710-766-01 IC BD12KA5FP-E2
IC1014 8-759-447-77 IC TC7WH74FU (TE12R)
IC1031 6-705-469-01 IC BA50BC0FP-E2
IC1101 6-808-148-02 IC MB90F046PF-G-117E1
1111 6-702-913-01 IC S-80929CNMC-G8ZT2G
IC
IC1131 (Not supplied) IC S-24CS16A0I-J8T1G
IC1301 8-759-825-15 IC LC89056W-E
IC1303 8-759-096-87 IC TC7WU04FU (TE12R)
IC1351 6-600-466-01 IC TORX147L (SONY)
IC1352 6-600-466-01 IC TORX147L (SONY) (DIGITAL OPTICAL BD IN)
IC1401 6-710-554-01 IC PCM1808PWR
IC1403 8-759-710-97 IC NJM4565M-D
IC1404 8-759-710-97 IC NJM4565M-D
IC1405 8-759-710-97 IC NJM4565M-D
IC1406 8-759-710-97 IC NJM4565M-D
IC1452 6-711-874-01 IC WM8768GEDS/R
IC1501 6-706-764-01 IC ADSP21266SKSTZ-2C
IC1902 8-759-231-56 IC TA7809S
IC1903 6-705-463-01 IC BA33BC0T
IC1904 6-705-468-01 IC BA33BC0FP-E2
IC1905 6-705-463-01 IC BA33BC0T
IC1906 6-712-614-01 IC SI-3050KM-TLS
< JACK >
J1301 1-793-446-21 JACK, PIN 1P (DIGITAL COAXIAL DVD IN)
< CONNECTOR >
J1302 1-817-615-21 CONNECTOR, SQUARE
< JUMPER RESISTOR/CAPACITOR >
JR1003 1-211-950-11 SHORT CHIP 0
JR1004 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
Note 1: Refer to supplement-1 for DIGITAL
AB board (Thai model).
(DIGITAL OPTICAL SAT IN)
TYPE (RECE) (DMPORT)
Note 2: IC1131 cannot exchange with single. When IC1 131
is damaged, exchange the entire mounted board.
R1010 1-216-809-11 METAL CHIP 100 5% 1/10W
R1011 1-216-809-11 METAL CHIP 100 5% 1/10W
R1012 1-216-809-11 METAL CHIP 100 5% 1/10W
R1013 1-216-809-11 METAL CHIP 100 5% 1/10W
R1014 1-216-809-11 METAL CHIP 100 5% 1/10W
R1015 1-216-809-11 METAL CHIP 100 5% 1/10W
R1016 1-216-809-11 METAL CHIP 100 5% 1/10W
R1017 1-216-805-11 METAL CHIP 47 5% 1/10W
R1018 1-216-805-11 METAL CHIP 47 5% 1/10W
R1019 1-216-809-11 METAL CHIP 100 5% 1/10W
R1020 1-216-809-11 METAL CHIP 100 5% 1/10W
R1021 1-216-809-11 METAL CHIP 100 5% 1/10W
R1022 1-216-809-11 METAL CHIP 100 5% 1/10W
R1023 1-216-805-11 METAL CHIP 47 5% 1/10W
R1024 1-216-864-11 SHORT CHIP 0
R1027 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R1028 1-216-801-11 METAL CHIP 22 5% 1/10W
R1029 1-216-801-11 METAL CHIP 22 5% 1/10W
R1030 1-216-801-11 METAL CHIP 22 5% 1/10W
R1031 1-216-801-11 METAL CHIP 22 5% 1/10W
R1033 1-216-833-11 METAL CHIP 10K 5% 1/10W
R1034 1-216-821-11 METAL CHIP 1K 5% 1/10W
R1035 1-216-833-11 METAL CHIP 10K 5% 1/10W
R1036 1-216-864-11 SHORT CHIP 0
R1037 1-216-833-11 METAL CHIP 10K 5% 1/10W
R1038 1-216-801-11 METAL CHIP 22 5% 1/10W
R1039 1-216-833-11 METAL CHIP 10K 5% 1/10W
R1040 1-216-801-11 METAL CHIP 22 5% 1/10W
R1043 1-216-801-11 METAL CHIP 22 5% 1/10W
R1046 1-216-801-11 METAL CHIP 22 5% 1/10W
R1047 1-216-801-11 METAL CHIP 22 5% 1/10W
R1048 1-216-857-11 METAL CHIP 1M 5% 1/10W
R1049 1-216-817-11 METAL CHIP 470 5% 1/10W
R1050 1-216-833-11 METAL CHIP 10K 5% 1/10W
R1053 1-216-833-11 METAL CHIP 10K 5% 1/10W
R1062 1-216-801-11 METAL CHIP 22 5% 1/10W
R1068 1-216-801-11 METAL CHIP 22 5% 1/10W
R1069 1-216-833-11 METAL CHIP 10K 5% 1/10W
R1070 1-216-864-11 SHORT CHIP 0
R1071 1-216-833-11 METAL CHIP 10K 5% 1/10W
R1072 1-216-827-11 METAL CHIP 3.3K 5% 1/10W
R1073 1-216-827-11 METAL CHIP 3.3K 5% 1/10W
R1074 1-216-809-11 METAL CHIP 100 5% 1/10W
R1076 1-216-809-11 METAL CHIP 100 5% 1/10W
R1077 1-216-809-11 METAL CHIP 100 5% 1/10W
R1078 1-216-809-11 METAL CHIP 100 5% 1/10W
R1080 1-216-864-11 SHORT CHIP 0
R1081 1-216-864-11 SHORT CHIP 0
R1083 1-216-833-11 METAL CHIP 10K 5% 1/10W
R1084 1-216-809-11 METAL CHIP 100 5% 1/10W
R1088 1-216-833-11 METAL CHIP 10K 5% 1/10W
R1094 1-216-833-11 METAL CHIP 10K 5% 1/10W
R1095 1-216-833-11 METAL CHIP 10K 5% 1/10W
R1100 1-216-864-11 SHORT CHIP 0
R1101 1-216-864-11 SHORT CHIP 0
R1102 1-216-864-11 SHORT CHIP 0
R1103 1-216-864-11 SHORT CHIP 0
R1104 1-216-864-11 SHORT CHIP 0
5959
Page 60
STR-KM5000
Ver. 1.1
DIGIT AL AB
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
R1105 1-216-833-11 METAL CHIP 10K 5% 1/10W
R1106 1-216-809-11 METAL CHIP 100 5% 1/10W
R1107 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R1108 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R1110 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R1111 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R1112 1-216-809-11 METAL CHIP 100 5% 1/10W
R1116 1-216-809-11 METAL CHIP 100 5% 1/10W
R1117 1-216-821-11 METAL CHIP 1K 5% 1/10W
R1118 1-216-821-11 METAL CHIP 1K 5% 1/10W
R1122 1-216-809-11 METAL CHIP 100 5% 1/10W
R1123 1-216-809-11 METAL CHIP 100 5% 1/10W
R1124 1-216-809-11 METAL CHIP 100 5% 1/10W
R1127 1-216-809-11 METAL CHIP 100 5% 1/10W
R1128 1-216-809-11 METAL CHIP 100 5% 1/10W
R1129 1-216-809-11 METAL CHIP 100 5% 1/10W
R1130 1-216-809-11 METAL CHIP 100 5% 1/10W
R1131 1-216-809-11 METAL CHIP 100 5% 1/10W
R1132 1-216-809-11 METAL CHIP 100 5% 1/10W
R1133 1-216-809-11 METAL CHIP 100 5% 1/10W
R1134 1-216-809-11 METAL CHIP 100 5% 1/10W
R1135 1-216-809-11 METAL CHIP 100 5% 1/10W
R1148 1-216-803-11 METAL CHIP 33 5% 1/10W
R1151 1-216-809-11 METAL CHIP 100 5% 1/10W
R1152 1-216-809-11 METAL CHIP 100 5% 1/10W
R1153 1-216-809-11 METAL CHIP 100 5% 1/10W
R1156 1-216-864-11 SHORT CHIP 0
R1157 1-216-864-11 SHORT CHIP 0
R1159 1-216-827-11 METAL CHIP 3.3K 5% 1/10W
R1162 1-216-809-11 METAL CHIP 100 5% 1/10W
R1163 1-216-833-11 METAL CHIP 10K 5% 1/10W
(E51, MX)
R1163 1-216-841-11 METAL CHIP 47K 5% 1/10W
(SP, MY, AR)
R1164 1-216-833-11 METAL CHIP 10K 5% 1/10W
(SP, MY, AR)
R1164 1-216-841-11 METAL CHIP 47K 5% 1/10W
(E51, MX)
R1174 1-216-809-11 METAL CHIP 100 5% 1/10W
R1175 1-216-809-11 METAL CHIP 100 5% 1/10W
R1179 1-216-833-11 METAL CHIP 10K 5% 1/10W
R1180 1-216-833-11 METAL CHIP 10K 5% 1/10W
R1181 1-216-833-11 METAL CHIP 10K 5% 1/10W
R1182 1-216-833-11 METAL CHIP 10K 5% 1/10W
R1183 1-216-833-11 METAL CHIP 10K 5% 1/10W
R1184 1-216-833-11 METAL CHIP 10K 5% 1/10W
R1185 1-216-833-11 METAL CHIP 10K 5% 1/10W
R1186 1-216-833-11 METAL CHIP 10K 5% 1/10W
R1187 1-216-833-11 METAL CHIP 10K 5% 1/10W
R1188 1-216-833-11 METAL CHIP 10K 5% 1/10W
R1189 1-216-833-11 METAL CHIP 10K 5% 1/10W
R1190 1-216-833-11 METAL CHIP 10K 5% 1/10W
R1191 1-216-833-11 METAL CHIP 10K 5% 1/10W
R1192 1-216-833-11 METAL CHIP 10K 5% 1/10W
R1193 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R1193 1-216-833-11 METAL CHIP 10K 5% 1/10W
R1193 1-216-841-11 METAL CHIP 47K 5% 1/10W
(SP, MY)
R1193 1-216-864-11 SHORT CHIP 0 (AR)
R1194 1-216-833-11 METAL CHIP 10K 5% 1/10W
R1194 1-216-841-11 METAL CHIP 47K 5% 1/10W
R1200 1-216-809-11 METAL CHIP 100 5% 1/10W
R1203 1-216-809-11 METAL CHIP 100 5% 1/10W
R1253 1-216-833-11 METAL CHIP 10K 5% 1/10W
R1260 1-216-821-11 METAL CHIP 1K 5% 1/10W
R1261 1-216-821-11 METAL CHIP 1K 5% 1/10W
R1301 1-216-830-11 METAL CHIP 5.6K 5% 1/10W
R1302 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R1303 1-216-839-11 METAL CHIP 33K 5% 1/10W
R1304 1-216-809-11 METAL CHIP 100 5% 1/10W
R1305 1-216-817-11 METAL CHIP 470 5% 1/10W
R1306 1-216-801-11 METAL CHIP 22 5% 1/10W
R1307 1-216-809-11 METAL CHIP 100 5% 1/10W
R1308 1-216-809-11 METAL CHIP 100 5% 1/10W
R1309 1-216-809-11 METAL CHIP 100 5% 1/10W
R1310 1-216-857-11 METAL CHIP 1M 5% 1/10W
R1311 1-216-809-11 METAL CHIP 100 5% 1/10W
R1312 1-216-809-11 METAL CHIP 100 5% 1/10W
R1313 1-216-809-11 METAL CHIP 100 5% 1/10W
R1314 1-216-833-11 METAL CHIP 10K 5% 1/10W
R1318 1-216-833-11 METAL CHIP 10K 5% 1/10W
R1319 1-216-817-11 METAL CHIP 470 5% 1/10W
R1321 1-216-864-11 SHORT CHIP 0
R1323 1-216-833-11 METAL CHIP 10K 5% 1/10W
R1325 1-216-821-11 METAL CHIP 1K 5% 1/10W
R1350 1-216-833-11 METAL CHIP 10K 5% 1/10W
R1351 1-216-809-11 METAL CHIP 100 5% 1/10W
R1352 1-216-864-11 SHORT CHIP 0
R1353 1-216-864-11 SHORT CHIP 0
R1354 1-216-809-11 METAL CHIP 100 5% 1/10W
R1355 1-218-285-11 METAL CHIP 75 5% 1/10W
R1356 1-216-817-11 METAL CHIP 470 5% 1/10W
R1357 1-216-841-11 METAL CHIP 47K 5% 1/10W
R1358 1-216-853-11 METAL CHIP 470K 5% 1/10W
R1359 1-216-809-11 METAL CHIP 100 5% 1/10W
R1360 1-216-809-11 METAL CHIP 100 5% 1/10W
R1361 1-216-864-11 SHORT CHIP 0
R1362 1-216-855-11 METAL CHIP 680K 5% 1/10W
R1367 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R1401 1-216-809-11 METAL CHIP 100 5% 1/10W
R1414 1-218-867-11 METAL CHIP 6.8K 0.5% 1/10W
R1415 1-216-864-11 SHORT CHIP 0
R1416 1-216-821-11 METAL CHIP 1K 5% 1/10W
R1420 1-216-864-11 SHORT CHIP 0
R1424 1-216-832-11 METAL CHIP 8.2K 5% 1/10W
R1425 1-216-864-11 SHORT CHIP 0
R1426 1-216-821-11 METAL CHIP 1K 5% 1/10W
R1427 1-216-864-11 SHORT CHIP 0
R1434 1-218-867-11 METAL CHIP 6.8K 0.5% 1/10W
R1435 1-216-864-11 SHORT CHIP 0
R1436 1-216-821-11 METAL CHIP 1K 5% 1/10W
R1454 1-218-867-11 METAL CHIP 6.8K 0.5% 1/10W
(MX)
R1455 1-216-864-11 SHORT CHIP 0
(E51)
R1456 1-216-821-11 METAL CHIP 1K 5% 1/10W
R1463 1-218-867-11 METAL CHIP 6.8K 0.5% 1/10W
R1464 1-216-864-11 SHORT CHIP 0
R1466 1-216-821-11 METAL CHIP 1K 5% 1/10W
Note: Refer to supplement-1 for DIGITAL
AB board (Thai model).
(SP, MY)
(E51, MX)
60
Page 61
STR-KM5000
Ver. 1.1
DISPLAYDIGIT AL AB
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
R1468 1-216-832-11 METAL CHIP 8.2K 5% 1/10W
R1473 1-218-867-11 METAL CHIP 6.8K 0.5% 1/10W
R1474 1-216-833-11 METAL CHIP 10K 5% 1/10W
R1476 1-216-821-11 METAL CHIP 1K 5% 1/10W
R1483 1-218-867-11 METAL CHIP 6.8K 0.5% 1/10W
R1484 1-216-864-11 SHORT CHIP 0
R1485 1-216-864-11 SHORT CHIP 0
R1486 1-216-821-11 METAL CHIP 1K 5% 1/10W
R1491 1-218-867-11 METAL CHIP 6.8K 0.5% 1/10W
R1493 1-218-867-11 METAL CHIP 6.8K 0.5% 1/10W
R1494 1-218-867-11 METAL CHIP 6.8K 0.5% 1/10W
R1495 1-218-867-11 METAL CHIP 6.8K 0.5% 1/10W
R1496 1-216-832-11 METAL CHIP 8.2K 5% 1/10W
R1497 1-218-867-11 METAL CHIP 6.8K 0.5% 1/10W
R1498 1-218-867-11 METAL CHIP 6.8K 0.5% 1/10W
R1524 1-216-864-11 SHORT CHIP 0
R1530 1-216-845-11 METAL CHIP 100K 5% 1/10W
R1556 1-216-815-11 METAL CHIP 330 5% 1/10W
R1635 1-216-833-11 METAL CHIP 10K 5% 1/10W
R1636 1-216-833-11 METAL CHIP 10K 5% 1/10W
R1641 1-216-833-11 METAL CHIP 10K 5% 1/10W
R1643 1-216-833-11 METAL CHIP 10K 5% 1/10W
R1644 1-216-833-11 METAL CHIP 10K 5% 1/10W
R1645 1-216-833-11 METAL CHIP 10K 5% 1/10W
R1901 1-216-833-11 METAL CHIP 10K 5% 1/10W
R1922 1-216-864-11 SHORT CHIP 0
R1940 1-216-864-11 SHORT CHIP 0
R1947 1-216-801-11 METAL CHIP 22 5% 1/10W
R1948 1-216-809-11 METAL CHIP 100 5% 1/10W
R1949 1-216-841-11 METAL CHIP 47K 5% 1/10W
IC5001 6-709-221-01 IC TMDS341PFCR
IC5002 6-705-337-01 IC TK11150CSCL-G
IC5003 6-705-468-01 IC BA33BC0FP-E2
IC5004 6-704-099-01 IC TC7WZ08FK (TE85R)
IC5005 6-707-207-01 IC SN74L
R5002 1-218-844-11 METAL CHIP 750 0.5% 1/10W
R5003 1-216-833-11 METAL CHIP 10K 5% 1/10W
R5004 1-216-864-11 SHORT CHIP 0
R5005 1-216-864-11 SHORT CHIP 0
R5006 1-216-864-11 SHORT CHIP 0
R5007 1-216-864-11 SHORT CHIP 0
R5008 1-216-864-11 SHORT CHIP 0
R5009 1-216-864-11 SHORT CHIP 0
R5010 1-216-864-11 SHORT CHIP 0
R5011 1-216-864-11 SHORT CHIP 0
VC1G3157DCKR
< CAPACITOR >
C791 1-100-566-91 CERAMIC CHIP 0.1uF 10% 25V
< CONNECTOR >
* CNP790 1-564-507-11 PLUG, CONNECTOR 4P
< JACK >
J790 1-815-314-21 JACK (PHONES)
< LEAD >
* TP790 1-690-880-31 LEAD (WITH CONNECTOR)
*************************************************************
A-1438-326-A MAIN BOARD, COMPLETE (MX, SP, MY, AR, TH)
A-1438-327-A MAIN BOARD, COMPLETE (E51)
*********************
0 IC201 8-759-231-53 IC TA7805S
0 IC202 8-759-373-92 IC TA79005SB
IC210 6-704-199-01 IC NJM2595M-TE2
IC220 6-706-767-01 IC NJM2586AM
< JACK
J210 1-815-043-11 JACK, PIN 2P
J211 1-794-978-11 JACK, PIN 3P (VIDEO 1 VIDEO OUT,DVD VIDEO
J220 1-816-592-11 JACK, PIN 9P (COMPONENT VIDEO DVD IN/
J221 1-821-278-12 JACK 3P (COMPONENT VIDEO SAT IN)
< RESISTOR >
R211 1-211-990-11 METAL CHIP 75 0.5% 1/10W
R212 1-211-990-11 METAL CHIP 75 0.5% 1/10W
R213 1-211-990-11 METAL CHIP 75 0.5% 1/10W
R214 1-211-990-11 METAL CHIP 75 0.5% 1/10W
R215 1-211-990-11 METAL CHIP 75 0.5% 1/10W
Checking the version allows you to jump to the revised page.
Also, clicking the version at the top of the revised page allows you to jump to the next revised page.
Ver.DateDescription of Revision
1.02008.03New
1.12008.08Addition of Thai model
Change of DISPLAY, HEADPHONE, VIDEO 2 boards (Suffi
(Suffi x-12)
Change of DIGITAL AB board (Suffi x-12) and STEREO SW board (Suffi x-13) (SUPPLEMENT-1)
1.22009.01Addition of Part No. for complete STANDBY board (SMR-08209)
1.32010.02Addition of Part No. for MICA SHEET (SMR-09112)
x-12/13) and STEREO SW board
(SMR-08085)
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.