Sony STRK-5900-P Service manual

STR-K5900P/K9900P
SERVICE MANUAL
Ver. 1.0 2005. 03
• STR-K5900P/K9900P are the FM/AM receiver section in HT-5950DP/6900DP/9900M.
Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic” and the double-D symbol are trademarks of Dolby Laboratories. “DTS”, “DTS-ES”, “Neo:6” and “DTS 96/24” are trademarks of Digital Theater Systems, Inc.
Photo: STR-K9900P
SPECIFICATIONS
US Model
STR-K5900P/K9900P
Canadian Model
STR-K5900P
DISTORTION: (Models of area code US only)
With 6 ohm loads, both channels driven, from 120 – 20,000 Hz; rated 90 watts (STR-K9900P)/ 70 watts (STR-K5900P) per channel minimum RMS power, with no more than 0.7 % total harmonic distortion from 250 milliwatts to rated output.
Amplifier section
Power Output Model of area code US (6 ohms 1 kHz, THD 10 %) STR-K9900P: FRONT
STR-K5900P: FRONT
1)
2)
: 140 W/ch
2)
CENTER SURR SURR BACK
CENTER SURR SURR BACK
: 140 W
2)
: 140 W/ch
2)
: 110 W/ch
2)
: 110 W
2)
: 110 W/ch
2)
: 140 W
2)
: 110 W
Model of area code Canadian (6 ohms 1 kHz, THD 0.7 %) STR-K5900P: FRONT
(6 ohms 1 kHz, THD 10 %) STR-K5900P: FRONT
1) Measured under the following conditions: Area code Power requirements
US, Canadian 120 V AC, 60 Hz
2) Depending on the sound field settings and the source, there may be no sound output.
2)
: 70 W/ch
2)
CENTER
2)
SURR
: 70 W/ch
SURR BACK
2)
: 110 W/ch
2)
CENTER
2)
SURR
: 110 W/ch
SURR BACK
: 70 W
2)
: 70 W
: 110 W
2)
: 110 W
– Continued on next page –
9-879-562-01
2005C04-1 © 2005. 03
FM STEREO/FM-AM RECEIVER
Sony Corporation
Audio Group Published by Sony Engineering Corporation
1
STR-K5900P/K9900P
Inputs (Analog) MUL TI CH IN*, Sensitivity: 800 mV
SA-CD/CD, MD/TAPE, Impedance: 50 k ohms DVD, VIDEO 1, 2, 3
* STR-K9900P only.
Inputs (Digital) DVD (Coaxial) Sensitivity: –
VIDEO 2, SA-CD/CD Sensitivity: – (Optical) Impedance: –
Outputs (Analog) MD/TAPE (OUT), Voltage: 800 mV
VIDEO 1 (AUDIO OUT) Impedance: 10 k ohms SUB WOOFER V oltage: 2 V
Reproduction frequency range:
Tone Gain levels ±6 dB, 1 dB step
FM tuner section
Tuning range 87.5 – 108.0 MHz Antenna FM wire antenna Antenna terminals 75 ohms, unbalanced Intermediate frequency 10.7 MHz
Impedance: 75 ohms
Impedance: 1 k ohm
28 – 20,000 Hz
AM tuner section
Tuning range Model of area code US, Canadian With 10-kHz tuning scale: 530 – 1,710 kHz With 9-kHz tuning scale: 531 – 1,710 kHz Antenna Loop antenna Intermediate frequency 450 kHz
3) You can change the AM tuning scale to 9 kHz or 10 kHz. After tuning in any AM station, turn off the receiver. While holding down PRESET TUNING + or TUNING +, press ?/1. All preset stations will be erased when you change the tuning scale. To reset the scale to 10 kHz (or 9 kHz), repeat the procedure.
3)
3)
Video section
Inputs/Outputs Video: 1 Vp-p, 75 ohms COMPONENT VIDEO: Y: 1 Vp-p, 75 ohms
PB/CB/B-Y: 0.7 Vp-p, 75 ohms PR/CR/R-Y: 0.7 Vp-p, 75 ohms 80 MHz HD Pass Through
General
Power requirements Area code Power requirements
US, Canadian 120 V AC, 60 Hz
Power consumption Area code Power consumption
US (STR-K9900P) 190 W US (STR-K5900P) 140 W Canadian 200 V A
Power consumption (during standby mode)
Dimensions (w/h/d) (Approx.)
Mass (Approx.) 8.0 kg (17 lb 11 oz)
Design and specifications are subject to change without notice.
0.2 W
430 × 157.5 × 310 mm (16 7/8 × 6 2/8 × 12 2/8 inches) including projecting parts and controls
2
SAFETY CHECK-OUT (US MODEL)
After correcting the original service problem, perform the follow­ing safety check before releasing the set to the customer: Check the antenna terminals, metal trim, “metallized” knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below.
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microampers.). Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the manufacturers’ instructions to use these instruments.
2. A battery-operated AC milliammeter. The Data Precision 245 digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The “limit” indica­tion is 0.75 V, so analog meters must have an accurate low­voltage scale. The Simpson 250 and Sanwa SH-63Trd are ex­amples of a passive VOM that is suitable. Nearly all battery operated digital multimeters that have a 2 V AC range are suit­able. (See Fig. A)
STR-K5900P/K9900P
To Exposed Metal Parts on Set
0.15 µF
1.5 k
Earth Ground
AC voltmeter (0.75 V)
Fig. A. Using an AC voltmeter to check AC leakage.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY P ARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
3
STR-K5900P/K9900P
MODEL IDENTIFICATION
— BACK P ANEL —
Part No.
MODEL PART No.
STR-K5900P: US 2-546-121-0s STR-K9900P: US 2-546-121-1s STR-K5900P: CND 2-546-121-7s
•Abbreviation CND: Canadian model

TABLE OF CONTENTS

1. GENERAL
Main unit ................................................................................. 5
Remote button description....................................................... 6
2. DISASSEMBLY
2-1. Case ..................................................................................... 7
2-2. Front Panel Section ............................................................. 8
2-3. Back Panel Section.............................................................. 8
2-4. Digital Board .......................................................................9
2-5. Standby Board .....................................................................9
2-6. Main Board ....................................................................... 10
3. TEST MODE ..................................................................... 11
4. DIAGRAMS
4-1. Circuit Boards Location .................................................... 12
4-2. Block Diagram – Tuner/Audio Section –.......................... 13
4-3. Block Diagram – Digital Section – ................................... 14
4-4. Block Diagram – Video Section – ..................................... 15
4-5. Block Diagram – Key/Display Section – .......................... 16
4-6. Block Diagram – Power Section – .................................... 17
4-7. Printed Wiring Boards – Main Section – .......................... 19
4-8. Schematic Diagram – Main Section (1/2) – ...................... 20
4-9. Schematic Diagram – Main Section (2/2) – ...................... 21
4-10. Printed Wiring Board – Digital Section (1/2) – ................ 22
4-11. Printed Wiring Board – Digital Section (2/2) – ................ 23
4-12. Schematic Diagram – Digital Section (1/4) – ................... 24
4-13. Schematic Diagram – Digital Section (2/4) – ................... 25
4-14. Schematic Diagram – Digital Section (3/4) – ................... 26
4-15. Schematic Diagram – Digital Section (4/4) – ................... 27
4-16. Printed Wiring Boards – Speaker Section – ...................... 28
4-17. Schematic Diagram – Speaker Section – .......................... 29
4-18. Printed Wiring Boards – Video Section – ......................... 30
4-19. Schematic Diagram – Video Section –..............................31
4-20. Printed Wiring Boards – Panel Section – .......................... 32
4-21. Schematic Diagram – Panel Section – .............................. 33
4-22. Printed Wiring Board – Power Section – .......................... 34
4-23. Schematic Diagram – Power Section – ............................. 35
5. EXPLODED VIEWS
5-1. Case Section ...................................................................... 42
5-2. Front Panel Section ........................................................... 43
5-3. Back Panel Section............................................................ 44
5-4. Chassis Section ................................................................. 45
6. ELECTRICAL PARTS LIST ........................................ 46
4
SECTION 1
Illustrati
w

GENERAL

List of button locations and reference pages
STR-K5900P/K9900P
This section is extracted from instruction manual.
How to use this page
Use this page to find the location of buttons that are mentioned in the text.
Main unit
ALPHABETICAL ORDER
A - H
A.F.D. (button/indicator) qa (30,
32, 53) AM wa (23, 24, 25, 40) DIMMER 4 (26) DISPLAY 3 (26, 54) Display 7 (27) DVD wg (23) ENTER qg (18, 40) FM ws (23, 24, 25, 40) FM MODE es (24)
I - O
Input buttons w; (23, 35, 39, 40,
54) INPUT MODE qj (35) IR (receptor) 5 (43, 54)
MAIN MENU 8 (19, 36, 37, 40) MASTER VOLUME –/+ qh (18,
22, 23, 53) MD/TAPE wf (23) MEMORY ef (25) MOVIE (button/indicator) qs
(31, 32, 53) MULTI CHANNEL DECODING
(indicator) 6 (24) MULTI CH IN* 9 (24) MUSIC (button/indicator) qd (32,
53)
P - Z
PHONES (jack) ed (23, 53) PRESET TUNING –/+ wl (25,
56) SA-CD/CD wd (23) SLEEP** 9 (40) SPEAKERS (OFF/A/B/A+B)*
2 (16, 41, 53)
on number
r
DISPLAY 3 (26, 54)
Name of button/part Reference page
RR
SPEAKERS (ON/OFF)** 2 (16,
41, 53)
SURR BACK DECODING qf
(33) TUNING –/+ e; (24, 56) VIDEO 1 wk (23) VIDEO 2 wj (23) VIDEO 3 wh (23) VIDEO 3 IN/PORTABLE AV IN
(jacks) ea (13)
NUMBERS AND SYMBOLS
2CH (button/indicator) q; (29,
32, 37) ?/1 (power) 1 (18, 19, 37, 56) </> ql (19, 36, 37, 40) +/– qk (19, 36, 38, 40)
*HT-9900M and HT-6900 DP
only. **HT-5950DP only.
Additional Information
1
2
6534
7
8
9q;qa qs qfqd qg
wawswdwfwgwhwjwk
wle;edesef ea
qk
;
qjqlqh
59
US
5
STR-K5900P/K9900P
Operations Using the Remote RM-AAP001
You can use the remote RM-AAP001 to operate the components in your system.
Before you use your
Remote button description
remote
Inserting batteries into the remote
Insert R6 (size-AA) batteries with the + and – properly oriented in the battery compartment. When using the re m ote, point it at the remote sensor on the re ceiver.
Tip
Under normal conditions, the batteries should last for about 6 months. When the remote no long er ope r ates the receiver, replace all batteries with new ones.
Notes
•Do not leave the remote in an extremely hot or humid place.
•Do not use a new battery with an old one.
•Do not expose the remote sensor to direct sunlight or lighting apparatuses. Doing so may cau se a malfunction.
•If you don’t use the remote for an extended period of time, remove the batteries to avoid possible damage from battery leakage and corrosion.
1
2 3
4
TV ?/1 AV ?/1
RM SET UP
SYSTEM STANDBY
VIDEO1 VIDEO2 VIDEO3 DVD
AV1 AV2
SA-CD/CD TUNER
MD/TAPE
?/1
P
SLEEP
AUX
5
SEARCH MODE
X
V
v
RETURN/EXIT
MOVIE
DUAL
MONO
JUMP/
TIME
-
AV MENU
bB
O
TV/
VIDEO
MULTI CH
MUSIC
SB
DECODING
PRESET/
CH/D.SKIP
x
MUTING
MASTER
VOL
MAIN MENU
TEST TONEWIDE
6
2CH
A.F.D.
123
7
8
9
*
q;
456
AUDIO
ANGLE
789
SUBTITLE ENTER
>
.
0/10 >10/11 12
SHIFT
D.TUNING DISC ALT
Mm
ANT
CLEAR
H
TOP MENU/
GUIDE
qa
ENTER
DISPLAY
TV VOL TV CH
*
qs
*
qd
*The H, TV VOL +, TV CH + and MASTER
VOL + buttons have a tactile dot. Use the tactile dot as a reference when operating the receiver a nd other audio/video components.
ef ed
es ea e; wl
wk wj
wh
wg wf
wd ws wa w; ql
qk
qj qh
qg qf
Operations Using the Remote RM-AAP001
*
continued
US
43
6
SECTION 2

DISASSEMBLY

Note : This set can be disassemble according to the following sequence.
SET
2-1. CASE
(Page 7)
STR-K5900P/K9900P
2-2. FRONT PANEL SECTION
(Page 8)
2-5. STANDBY BOARD
(Page 9)
2-3. BACK PANEL SECTION
(Page 8)
2-4. DIGITAL BOARD
(Page 9)
2-6. MAIN BOARD
(Page 10)
Note : Follow the disassembly procedure in the numerical order given.
2-1. CASE
1
two screws
(case 3 TP2)
2
two screws
(+BVTP 3
×
8)
3
two screws
(case 3 TP2)
4

case

7
STR-K5900P/K9900P
)
2-2. FRONT P ANEL SECTION
2
CNP791 (4P)
6
two screws
(+BVTP 3
×
8)
1
clip
4
CNP202 (3P)
5
CNP503 (3P
7
two screws
(+BVTP 3
×
8)
2-3. BACK PANEL SECTION
5
CNP600 (4P)
6
CN806 (4P)
4
CNP503 (4P)
7
CNP901
9

front panel section

8
three screws
(+BVTP 3
qd

back panel section

3
CNS505 (21 core)
×
8)
8
four screws
(+BVTP 3 × 8)
qs
two screws
(+BVTP 3 × 8)
qa
five screws
(+BVTP 3 × 8)
0
three screws
(+BVTP 3 × 8)
9
screw
(+BVTP 3 × 8)
2
CNS509 (13P)
3
CNP203 (3P)
1
connector (11P)
8
2-4. DIGIT AL BOARD
d
8
screw
(+BVTP 3
3
CNP503 (6P)
×
8)
2
CNP504 (5P)
1
CNP505 (9P)
5
STR-K5900P/K9900P
0
DIGITAL boar
7
CNP501
CNP500
6
9
bracket (digital)
2-5. ST ANDBY BOARD
5
(+BV3 (3-CR))
2
three screws
CNP804 (3P)
4
CNP902 (2P)
6

STANDBY board

3
CNP903 (2P)
1
CNP801 (5P)
4
screw
(+BVTP 3
×
8)
9
STR-K5900P/K9900P
d
2-6. MAIN BOARD
5
screw (+BV3 (3-CR))
3
two screws
(+BV3 (3-CR))
2
CNP802 (5P)
1
CNP908 (5P)
4
two screws
(+BV3 (3-CR))
6
MAIN boar
10
SECTION 3

TEST MODE

STR-K5900P/K9900P
FACTORY PRESET MODE
* All preset contents are reset to the default setting. * Procedure:
While depressing the [FM MODE] and the [DISPLAY] buttons simultaneously, press the
?/1 button to turn on the main power .
The message “FA CT OR Y” appears for a moment and the present contents are reset to the default values.
AM CHANNEL STEP 9 kHz/10 kHz SELECTION MODE (US, Canadian model only)
* Either the 9 kHz step or 10 kHz step can be selected for the AM
channel step.
* Procedure:
Press the [AM] button to set AM and press the ?/1 button to turn off the main power. While depressing the [PRESET TUNING +] button or the [TUNING +] button, press the ?/1 button to turn on the main power. Either the message “9k STEP” or “10k STEP” appears for a moment and select the desired step.
SPEAKER SIZE SELECTION MODE
* Either the normal speaker or micro satellite speaker can be se-
lected.
* Procedure:
While depressing the [DIMMER] button, press the ?/1 button to turn on the main power. Either the message “NORM. SP .” or “MICRO SP.” appears for a moment and select the desired speaker size.
FLUORESCENT INDICATOR TUBE TEST MODE
* All fluorescent segments are tested.
When this test is activated, all segments light on at the same time, then each segment lights on one after another.
* Procedure:
While depressing the [TUNING --] and the [SPEAKERS $OFF/A/B/ A+B%] buttons simultaneously, press the the main power.
1. ALL segments light on.
SP A
D
D
LFE
SW
CR
L
SL S SR
SBL SB SBR
D
SP B SLEEP OPT COAX MULTI CH IN 96/24
D
DIGITALEX PRO LOGIC II x DTS-ES NEO:6 MPEG-2 AAC RDS
?/1 button to turn on
MEMORY
dB
kHz mft. MHz
DIRECT
D.RANGE EQ STEREO MONO
4. Press the [VIDEO 1] button, all segments and all LEDs light off.
5. Every pressing the [VIDEO 1] button turns on each segment and LED one after another in the same order. (Not only the [VIDEO 1] button, b ut also the other b uttons such as [VIDEO 2], [VIDEO 3], [DVD], [MD/TAPE], [SA-CD/CD], [FM] and [AM] can be used.)
SOUND FIELD CLEAR MODE
* The preset sound field is cleared when this mode is activated.
Use this mode before returning the product to clients upon completion of repair.
* Procedure:
While depressing the [2CH] button, press the ?/1 button to turn on the main power. The message “SF. CLR.” appears for a moment and initializa­tion is performed.
SOFTWARE VERSION DISPLAY MODE
* The software version is displayed. * Procedure:
While depressing the [TUNING --] and the [DISPLAY] buttons simultaneously, press the ?/1 button to turn on the main po wer . The model name, destination and the software version are dis­played for a moment.
KEY CHECK MODE
* Button check * Procedure:
While depressing the [TUNING --] and the [MAIN MENU] buttons simultaneously, press the ?/1 button to turn on the main po wer . Either the message “REST 30” appears. Every pressing of any button other than the
?/1 counts down
the buttons. The buttons which are already counted once are not counted again. When all buttons are pr essed “REST 00” appears.
COMMAND MODE SELECTION MODE
* The command mode (AV1 or AV2) of the remote commander
can be selected.
* Procedure:
While depressing the [ENTER] button, press the ?/1 button to turn on the main power. Either the message “C.MODE.AV 1” or “C.MODE.AV 2” ap­pears for a moment and select the desired mode.
[2CH], [A.F.D.], [MOVIE], [MUSIC] and [MULTI CHANNEL DE­CODING] LED light on.
2. Press the [VIDEO 1] button, confirm display.
SP A
D
D
LFE
LSWR
S
SB
D
SP B SLEEP OPT COAX MULTI CH IN 96/24
D
DIGITALEX PRO LOGIC II x DTS-ES NEO:6 MPEG-2 AAC RDS
D.RANGE EQ STEREO MONO
dB kHz mft. MHz
[A.F.D.] and [MUSIC] LED light on.
3. Press the [VIDEO 1] button, confirm display.
SP A
D
D
D
DIGITALEX PRO LOGIC II x DTS-ES NEO:6 MPEG-2 AAC RDS
D.RANGE EQ STEREO MONO
kHz mft. MHz
C
SL SR
SBL SBR
D
SP B SLEEP OPT COAX MULTI CH IN 96/24
[2CH], [MOVIE] and [MULTI CHANNEL DECODING] LED light on.
MEMORY
DIRECT
MEMORY
DIRECT
11
STR-K5900P/K9900P
d
4-1. CIRCUIT BOARDS LOCATION
STANDBY board
POWER board
TUNING board
HEADPHONE board
VIDEO3 board
SECTION 4

DIAGRAMS

SPEAKER B (P) board (STR-K9900P)
SPEAKER C/SB board
VIDEO board
DIGITAL boar
DISPLAY board
MAIN board
12
4-2. BLOCK DIAGRAM — TUNER/AUDIO SECTION —
STR-K5900P/K9900P
ANTENNA
FM 75 COAXIAL
TU+10V
3.3V
(STBY)
AM
TN1
FM/AM TUNER UNIT
L-CH
R-CH
STEREO
TUNED
MUTING
CE
DO
DATA
CLOCK
R-CH
76
STEREO
75
TUNED
78
MUTE
S LATCH
74 73
DO TUNER DATA
17
T SERIAL CLK
16
SW RY
70
J401
-1 -2 -3 -4 -5 -6
LR
FRONT
K9900P
SA-CD/CDINMD/TAPE
L
R
LR
R-CH
R-CH
R-CH
LR
SURROUND
CENTER
MULTI CH IN
OUT
SYSTEM
CONTROL
IC1101 (1/4)
R-CH
VOL DATA
VOL CLK
SUB
WOOFER
B
VIDEO 3 INPUT
AUDIO
LR
-2 -3-3 -4 -1 -2
SBR OUT
SBL OUT
SW OUT
C OUT
SL OUT
L OUT
R-CH
R-CH R-CH
DIR
FUNCTION SELECT
IC401
46
28 32 30
SEL SW
34
38
L
SEL
MCU
60
I/F
59
SL
SEL
10
13
12
17 11
R-CH
14
R-CH
SBL SEL
55
R-CH
54 56 51 52 49
SW SEL
SEL
C
+7V-7V
68 66
AVCCAVEE
R-CH
R-CH
R-CH
R-CH
R-CH
R-CH
44
45
24
25 26 27 41
42
88
87
85
84
86
81
83
MD/TAPEINDVD AUDIO
LRLR
-1 -2 -3 -4
J403J402 J298(2/2) J404
28 27
R-CH
IN
R-CH
DIGITAL
SECTION
(Page 14)
VIDEO 1
AUDIO OUT AUDIO INAUDIO IN
L
RL
-3 -4 -5 -6
RLR
-1 -2
5 7
SUB WOOFER
AMP
IC402
VIDEO 2
L-CH
R-CH
FL-CH
FR-CH
SL-CH
SR-CH
C-CH
SBL-CH
RELAY
DRIVER
Q560
A
C
RY560
DIGITAL
SECTION
(Page 14)
POWER
SECTION
(Page 17)
K9900P
J309
-2
-1
-2
SUB WOOFER
-1
AUDIO OUT
AUDIO
OUT
SUB
WOOFER
STR-K5900P/K9900P
• Signal path : TUNER (FM/AM) : VIDEO (AUDIO) : CD (ANALOG)
• R-ch is omitted due to same as L-ch.
13 13
STR-K5900P/K9900P
4-3. BLOCK DIAGRAM — DIGITAL SECTION —
A/D
CONVERTER
IC1401
TUNER/
AUDIO
SECTION
(Page 13)
DIGITAL
A
L-IN
R-IN R-CH
DVD
IN
(COAXIAL)
SA-CD/CD
IN
(OPTICAL)
VIDEO 2
IN
(OPTICAL)
+5V-2
J1301
-1
A.5V
IC1354
OUT
IC1351
OUT
LIN
1
1
1
ADC
IC1303
WAVE
SHAPER
Q1103
Q1104
GATE
LPF
INV.
SYS CLK
16
23
12.288MHz
X1301
D1105
D1106
D1103
AUDIO
I/F
DOUT
15
LRCK
13
SCLK
14
RST
6
DIGITAL AUDIO I/F RECEIVER
IC1301
DOUT
2
DIN2
5
INPUT
DIN1
4
DIN0
3
21
XOUT
22
XIN
VDD
+3.3V
Q1105
INV.
SYSTEM_MUTE
24
99
ERROR
25
ANA/DIG
DATA
DEMODULATOR
Pa,Pb DETECTION LOCK
C bit DETECTION
MICROPROCESSOR
I/F
CLKCEDIDOBPSYNC
38 37 36 35 33 47 17
95 96 97 98
DIR DI
DIR CE
DIR_CLK
CKSEL1
NC
94
DIR DO
DIR CKSEL1
20
XMCK
DETECTION
XSTATE
48
93100
DIR_XSTATE
XMODE
DIR_XMODE
AUDIO
24
CKOUT
13 22
BCK
14 29
LRCK
15 28
DATAO
16 30
D1301
ERROR
34 59
9
DIR_DATAO
PCM1800 RST
+2.6V
+3.3V
8
GP12
VDDI
VDDE
18
69
15
17
37
SDI1
GP8
KFSI0
BCKI2
LRCKI2
SDI2
LRCKI1
BCKI1
EXLOCK
GP12
GP9
68
21
GP9
HCS
HCS
HACN
HACN
DSP
IC1501
XRST
2 11336 35 33 3432
6 74 18 19 205
XRST
PM
PM
SD01 SD02 SD03
SD04
SCKOUT
LRCKO
BCKO
MCLK1
MCLK2
CSO
WEO
BST
HDIN
HDOUT
HDIN
HDOUT
D0-15A0-15
HCLK
HCLK
23 24 25
26
SCKOUT
14
LRCKO
19
BCKO
20
9
X1502
13.9MHz
12
44 45
98,80 - 77,75 - 72
108,107,105 -102,99,
85-82,66 - 64
112,110,109,97 - 92,
SWITCH
IC1503
56
5
6
92
SYSTEM
CONTROL
IC1101 (2/4)
SDRAM
IC1502
CS
6
17
WE
D0-15A0-15
16-13,10 - 7
29 - 32,35 - 38,
1 - 5,18 - 21
24 - 27,42 - 44,
LRCKO
2
1
BST SEL
8CH DAC
SCKOUT LRCKO BCKO
IC1452
VOUT5
DATA3
47
DATA1
45
DATA2
46
SCKI
38
LRCK
41
BCK
40
DATA4
31
RST
37
ML
36
MC
35
MDI
34
MDO
33
DAC
DAC
DAC
DAC
VOUT6
VOUT1
VOUT2
VOUT3
VOUT4
VOUT7
VOUT8
9
14
13
12
11
16
20
• Signal path : TUNER (FM/AM) : VIDEO (AUDIO)
AMP
IC1403
R-CH
R-CH
L OUT
SL OUT
C OUT
TUNER/
B
AUDIO
310
5
AMP
IC1405
5
3
AMP
IC1404
3
1
7
7
1
1
SECTION
5
AMP
IC1406
5
3
7
7
1
SW OUT
SBL OUT
SBR OUT
(Page 13)
: CD (DIGITAL)
• R-ch is omitted due to same as L-ch.
PCM1608ML
PCM1608MC
PCM1608RST
1514131210
PCM1608MDI
PCM1608MDO
3
BST
STR-K5900P/K9900P
1414
4-4. BLOCK DIAGRAM — VIDEO SECTION —
STR-K5900P/K9900P
VIDEO 2
IN
COMPONENT
VIDEO
DVD
IN
VIDEO 1
VIDEO 2
DVD
VIDEO 3
INPUT
• Signal path : VIDEO
P
P
P
P
B/CB/
R/CR/
B/CB/
R/CR/
VIDEO
VIDEO
VIDEO
VIDEO
-1
IN
-2
IN
-1
IN
-1
J301 (1/2)
Y
B-Y
R-Y
Y
B-Y
R-Y
J201 (1/2)
J200 (1/2)
J298 (1/2)
COMPONENT VIDEO SELECTOR
CH1 IN2
-4
-5
-6
-1
-2
-3
3
CH1 IN3
5
CH2 IN2
9
CH2 IN3
11
CH3 IN2
14
CH3 IN3
12
VIDEO
SELECTOR
IC203
V1
13
V2
5
DVD
3
V3
9
NC
7
IC304
6dB AMP
6dB AMP
6dB AMP
SW1 SW2
2 4
COMP SW1 COMP SW2
SW2
SW3
SW4
10 6 14 2
4
SW2
SW4
SW3
SW1
SW1
75
DRIVER
75
DRIVER
75
DRIVER
OR
D203,204
CHI OUT
CH2 OUT
CH3 OUT
SW5
V+1,+2
22
20
18
V-1,-2
6dB AMP
6dB AMP
+5V-3
-5V-3
J301 (2/2)
75
DRIVER
75
DRIVER
Y
-7
P
B/CB/
-8
P
R/CR/
-9
V1.OUT
M.OUT
MONITOR
B-Y
OUT
R-Y
VCC
+5V-3
15
1
VEE
-5V-3
COMPONENT
VIDEO
+5V-3
-5V-3
J200 (2/2)
J201 (2/2)
1 3
3 2
SW1 SW2
SW3
SW4
IC807
+5V
REG
IC804
-5V
REG
-3
VIDEO
OUT
-2
VIDEO
OUT
VIDEO 1
MONITOR
V SW1 V SW2
V SW3 V SW4 COMP SW1 COMP SW2
+15V
-15V
D
KEY/DISPLAY
SECTION
(Page 16)
STR-K5900P/K9900P
15 15
STR-K5900P/K9900P
4-5. BLOCK DIAGRAM — KEY/DISPLAY SECTION —
VIDEO
SECTION
(Page 15)
D
COMP SW2 COMP SW1
FLASH
PROGRAMMING
V SW1 V SW2 V SW3 V SW4
CNS504
1
2 7 6 5
EEPROM
IC1131
SDA
SCL
S131
I
/
I
FLASH1
FLASH2 MD2 MD0
RESET
SIRCS
FL DISPLAY DRIVER
IC100
STB
9
DIN
7
CLK
8
OUT
1
1
3
SEG1
I
SEG16
GRID12
I
GRID1
SW1 SW2 SW3 SW4
REMOTE CONTROL RECEIVER
IC102
RV102
MASTER
VOLUME
14
I
29
31
I
42
1 2 3 4
FL101
VACUUM
FLUORESCENT
DISPLAY
D101-104
SW1
86
SW2
87
SW3
88
SW4
89
COMP SW2
65
COMP SW1
71
29
X1101
24MHz
5
6
X1
X0
30
SDA
29
SCL
30
56
POWER KEY
28
FLASH1
27
FLASH2 MD2
51
MD0
49
SYSTEM
CONTROL
IC1101 (3/4)
FL DATA
VOL ENC A VOL ENC B
BLUE LED
FL LAT
FL CLK
SIRCS
57 59 60
54
45 46
47
9 4 2
LED DRIVE
Q110
BUFFER
IC101
8 6 3
D105
+3.3V
(STBY)
IC1111 RESET
A/D0
A/D1
A/D2
38
39
40
12
77
RSTX
SW NETWORK
S140-143,148-153
SW NETWORK
S120-125,128-130
SW NETWORK
S100-110
STR-K5900P/K9900P
1616
4-6. BLOCK DIAGRAM — POWER SECTION —
PRE DRIVER
IC701
IN 2
PRE
TUNER/
AUDIO
SECTION
(Page 13)
C
FL-CH
FR-CH
SL-CH
SR-CH R-CH
C-CH
SBL-CH
R-CH
8
8
1
6
IN 2
IN2
IN1
DRIVE
DRIVE
DRIVE
DRIVE
PRE
PRE
PRE
DRIVE
PRE DRIVER
IC601
DRIVE
PRE DRIVER
IC501
DRIVE
DRIVE
+VOUT2
-VOUT2
-B-1 +B
+VOUT2
-VOUT2
-B-1 +B
+VOUT2
-VOUT2
+VOUT1
-VOUT1
-B-1 +B
STR-K5900P/K9900P
J791
PHONES
R-CH
K5900P
TM610
TM601
TM501
L
R
L
R
L
SURROUND
R
SURROUND
FRONT B
FRONT A
CENTER
BACK
SPEAKERS
IMPEDANCE
USE 8-16
12 11
12 11
12 11
2 3
POWER AMP
Q701-704
POWER AMP
Q651-654
POWER AMP
Q501-504
POWER AMP
Q533,534,571,572
R-CH
R-CH
CURRENT
DETECT
Q705,706
R-CH
CURRENT
DETECT
Q655,656
R-CH R-CH
CURRENT
DETECT
Q505,506
CURRENT
DETECT
Q535,536
OVERLOAD
DETECT
D740,Q740
R-CH
OVERLOAD
DETECT
D640,Q640
OVERLOAD
DETECT
D540,Q540
OVERLOAD
DETECT
D580,Q580
HP-RY
SB-RY
RELAY
DRIVER
RELAY
DRIVER Q800(DE698/DV10) Q810(DE98)
RELAY
DRIVER
FRONT RY
REAR-RY
C/SB RY
HP DETECT
Q790
Q710
RELAY
DRIVER
Q610
RELAY
DRIVER
Q550
RY791
RY610
RY601
RY501
R-CH
R-CH
RY701
R-CH
PROTECTOR
HP_RY
FRONT RY
REAR_RY
C/SB RY
HP DETECT
SP_B_RY
SYSTEM
CONTROL
IC1101 (4/4)
BRIDGEABLE RY
P0WER RY
61
62
66
69
68
55
67
72
58
D1107
D1108
D1111
PROTECTOR
D721,722,732
Q722,723,725,793,795
D1110
HP-RY
FRONT-RY
REAR-RY
C/SB RY
HP DETECT
SB-RY
-B-1
IC691
OVERLOAD
DETECT AMP
-B SWITCH Q691,692
72
T901
POWER
TRANSFORMER
RECT
RECT
-20V
RECT
D910-913
F1
F2
RELAY
SWITCH
RY801
RY901
D804
R810
R811
R910
T902
POWER
TRANSFORMER
• Signal path : TUNER (FM/AM)
• R-ch is omitted due to same as L-ch.
F901
+B
-B
IC1904
+3.3V
REG
-32V REG Q801
13
5 2
IC1001
+5V REG
IC1901
BACK-UP
SWITCH
IC1902
+10V
13
REG
IC801
+7V
31
REG
-7V 23
REG
13
4
IC802
IC1031
+5V
REG
13
-20V
TU+10V
+7V
-7V
+5V-2
+5V-1
+2.6V +3.3V
+3.3V
(STBY)
+15V
-15V
RECT D802
RELAY
DRIVER
Q809
K9900P
RELAY
DRIVER
Q901
D920-923
D805-808
STR-K5900P/K9900P
STOP
Q921
48
D914
D915
~
AC IN
17 17
STR-K5900P/K9900P
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.)
for schematic diagram:
• All capacitors are in µF unless otherwise noted. (p: pF) 50 WV or less are not indicated except for electrolytics and tantalums.
• All resistors are in and 1/ specified.
f
2 : nonflammable resistor.
5 : fusible resistor.
C : panel designation.
A : B+ Line.
B : B– Line.
•Voltage and waveforms are dc with respect to ground
•Voltages are taken with a VOM (Input impedance 10 M).
•Waveforms are taken with a oscilloscope.
• Circled numbers refer to waveforms.
• Signal path.
: internal component.
Note:
The components identi­fied by mark 0 or dotted line with mark 0 are criti- cal for safety. Replace only with part number specified.
under no-signal (detuned) conditions. no mark : FM
Voltage variations may be noted due to normal produc­tion tolerances.
Voltage variations may be noted due to normal produc­tion tolerances.
F : TUNER (FM/AM) L : VIDEO (AUDIO) I : VIDEO J : CD (ANALOG) c : CD (DIGITAL)
4
W or less unless otherwise
Note:
Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une piéce portant le numéro spécifié.
for printed wiring boards:
X : parts extracted from the component side.
f
: Pattern from the side which enables seeing.
Caution: Pattern face side: Parts on the pattern face side seen from the (Side B) pattern face are indicated. Parts face side: Parts on the parts face side seen from the (Side A) parts face are indicated.
: internal component.
C Q
B
E
Q
BCE
Q
B
C
E
These are omitted.
These are omitted.
• Waveforms — DIGITAL Board —
1
IC1301 qd (CKOUT)
12.288MHz
1V/DIV, 50nsec/DIV
2
IC1301 qf (BCK)
3.07MHz
1V/DIV, 0.2µs/DIV
3
IC1301 wa (XOUT)
12.288MHz
1V/DIV, 50nsec/DIV
4
IC1501 9 (MCLK1)
3.5Vp-p
4.8Vp-p
3.2Vp-p
5
IC1501 qs (MCLK2)
13.9MHz
1V/DIV, 50nsec/DIV
6
IC1501 qf (SCKOUT)
12.288MHz
1V/DIV, 50nsec/DIV
7
IC1101 id (X1)
24MHz
1V/DIV, 50nsec/DIV
3.6Vp-p
3.5Vp-p
2Vp-p
1V/DIV, 50nsec/DIV
13.9MHz
1.8Vp-p
STR-K5900P/K9900P
1818
Loading...
+ 40 hidden pages