Sony STR-K402 User Manual

FM Stereo FM-AM Receiver
4-233-503-13(3)
Operating Instructions
Owner’s Record
Model No. STR-DE475/K402 Serial No.
STR-DE475 STR-K402
© 2001 Sony Corporation
WARNING
Precautions
To prevent fire or shock hazard, do not expose the unit to rain or moisture.
For customers in the United States
This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
INFORMATION
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: – Reorient or relocate the receiving antenna. – Increase the separation between the
equipment and receiver.
– Connect the equipment into an outlet on a
circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/
TV technician for help.
CAUTION
You are cautioned that any changes or modification not expressly approved in this manual could void your authority to operate this equipment.
Note to CATV system installer:
This reminder is provided to call CATV system installer’s attention to Article 820­40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.
Owner’s Record
The model and serial numbers are located on the rear of the unit. Record the serial number in the space provided below. Refer to them whenever you call upon your Sony dealer regarding this product.
Model No. STR-DE475/K402 Serial No.
For customers in Canada CAUTION
TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS POLARIZED AC PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.
For customers in the United States and Canada
ENERGY STAR® is a U.S. registered mark. As an ENERGY STAR® partner, Sony Corporation has determined that this product meets the ENERGY STAR guidelines for energy efficiency
®
For customers in other countries
To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.
Do not install the appliance in a confined space, such as a bookcase or built-in cabinet.
On safety
• Should any solid object or liquid fall into the cabinet, unplug the receiver and have it checked by qualified personnel before operating it any further.
• To prevent fire, do not cover the ventilation of the receiver with newspapers, table cloths, curtains, etc. And don’t place lighted candles on the receiver.
• To prevent fire or shock hazards, do not place vases on the receiver.
On power sources
• Before operating the receiver, check that the operating voltage is identical with your local power supply. The operating voltage is indicated on the nameplate at the rear of the receiver.
• The unit is not disconnected from the AC power source (mains) as long as it is connected to the wall outlet, even if the unit itself has been turned off.
• If you are not going to use the receiver for a long time, be sure to disconnect the receiver from the wall outlet. To disconnect the AC power cord, grasp the plug itself; never pull the cord.
• One blade of the plug is wider than the other for the purpose of safety and will fit into the wall outlet only one way. If you are unable to insert the plug fully into the outlet, contact your dealer. (for customers in the United States and Canada only)
• AC power cord must be changed only at the qualified service shop.
On placement
• Place the receiver in a location with adequate ventilation to prevent heat buildup and prolong the life of the receiver.
• Do not place the receiver near heat sources, or in a place subject to direct sunlight, excessive dust or mechanical shock.
• Do not place anything on top of the cabinet that might block the ventilation holes and cause malfunctions.
• Although the receiver heats up during operation, this is not a malfunction. If you continuously use this receiver at a large volume, the cabinet temperature of the top, side and bottom rises accordingly. To avoid burning yourself, do not touch the cabinet.
On operation
Before connecting other components, be sure to turn off and unplug the receiver.
On cleaning
Clean the cabinet, panel and controls with a soft cloth slightly moistened with a mild detergent solution. Do not use any type of abrasive pad, scouring powder or solvent such as alcohol or benzine.
If you have any question or problem concerning your receiver, please consult your nearest Sony dealer.
2
About This Manual
The instructions in this manual are for models STR-DE475 and STR-K402. Check your model number by looking at the lower right corner of the front panel.
About area codes
The area code of the player you purchased is shown on the lower portion of the rear panel (see the illustration below).
VOLTAGE SELECTORVOLTAGE SELECTOR
120V
240V 220V
IMPEDANCE USE 8 – 16
IMPEDANCE USE 8 – 16
S
S
FRONT
CENTER
RL
RL
Any differences in operation, according to the area code, are clearly indicated in the text, for example, “Models of area code AA only”.
Conventions
• The instructions in this manual describe the controls on the receiver. You can also use the controls on the supplied remote if they have the same or similar names as those on the receiver.
• The following icon is used in this manual: z Indicates hints and tips for making the task easier.
This receiver incorporates Dolby Surround and the DTS** Digital Surround System.
Manufactured under license from Dolby Laboratories.
*
“Dolby”, “AC-3”, “Pro Logic” and the double-D symbol a are trademarks of Dolby Laboratories.
Confidential unpublished Works. © 1992-1997 Dolby Laboratories. All rights reserved. Manufactured under license from Digital Theater Systems, Inc. US
**
Pat. No. 5,451,942, 5,956,674, 5,974,380, 5,978,762 and other world-wide patents issued and pending. “DTS” and “DTS Digital Surround” are registered trademarks of Digital Theater Systems, Inc. Copyright 1996, 2000 Digital Theater Systems, Inc. All Rights Reserved.
4-XXX-XXX-XX AA
Area code
* Digital and Pro Logic
TABLE OF CONTENTS
Hooking Up the Components 4
Unpacking 4 Antenna Hookups 5 Audio Component Hookups 6 Video Component Hookups 7 Digital Component Hookups 8 MULTI CH IN Hookups 9 Other Hookups 10
Hooking Up and Setting Up the Speaker System 11
Speaker System Hookup 12 Performing Initial Setup Operations 14 Multi Channel Surround Setup 15 Before You Use Your Receiver 19
Location of Parts and Basic Operations 21
Front Panel Parts Descriptions 21
Enjoying Surround Sound 24
Selecting a Sound Field 25 Understanding the Multi-Channel Surround Displays 28 Customizing Sound Fields 30
Receiving Broadcasts 34
Direct Tuning 36 Automatic Tuning 36 Preset Tuning 37
Other Operations 38
Naming Preset Stations and Program Sources 39 Recording 39 Using the Sleep Timer 40 Adjustment Using the SET UP Button 41
Additional Information 42
Troubleshooting 42 Specifications 44 Glossary 46 Settings Using SURR, LEVEL, and SET UP buttons 47 Remote Button Description 48 Index 51
3
Hooking Up
Unpacking
the Components
This chapter describes how to connect various audio and video components to the receiver. Be sure to read the sections for the components you have before you actually connect them to the receiver.
Check that you received the following items with the receiver:
• FM wire antenna (1)
• AM loop antenna (1)
• R6 (size-AA) batteries (2)
• Remote Commander (remote) (1)
Inserting batteries into the remote
Insert R6 (size-AA) batteries with the + and – properly oriented in the battery compartment. When using the remote, point it at the remote sensor
}
z
When to replace batteries
Under normal conditions, the batteries should last for about 6 months. When the remote no longer operates the receiver, replace all batteries with new ones.
g
]
}
]
on the receiver.
Notes
• Do not leave the remote in an extremely hot or humid place.
• Do not use a new battery with an old one.
• Do not expose the remote sensor to direct sunlight or lighting apparatuses. Doing so may cause a malfunction.
• If you don’t use the remote for an extended period of time, remove the batteries to avoid possible damage from battery leakage and corrosion.
Before you get started
• Turn off the power to all components before making
any connections.
• Do not connect the AC power cords until all of the
connections are completed.
• Be sure to make connections firmly to avoid hum and
noise.
• When connecting an audio/video cord, be sure to
match the color-coded pins to the appropriate jacks on the components: yellow (video) to yellow; white (left, audio) to white; and red (right, audio) to red.
4
Antenna Hookups
AM loop antenna (supplied)
FM wire antenna (supplied)
FM
75
COAXIAL
DIGITAL
DIGITAL
TV/SAT
DVD/LD
IN
IN
AM
ANTENNA ANTENNAANTENNA
FRONT
L
R
SURROUND
MULTI CH INMULTI CH IN
CENTER
SUB
WOOFER
COAXIAL
OPTICAL
L
R
IN OUT IN AUDIO IN AUDIO IN AUDIO OUT
CDCD MD/TAPEMD/TAPE VIDEOVIDEO
VIDEO IN
TV/SATTV/SAT
VIDEO IN
DVD/LDDVD/LD
VIDEO OUT
MONITOR
VIDEO IN
AUDIO IN
WOOFER
WOOFER
VIDEO OUT
AUDIO
OUT
SUB
SUB
SPEAKERSSPEAKERS
RL
RL
IMPEDANCE USE 8 – 16
IMPEDANCE USE 8 – 16
RL
RL
Hooking Up the System
FRONTCENTERSURROUND
Terminals for connecting the antennas
Connect the To the
AM loop antenna AM terminals FM wire antenna FM 75 COAXIAL terminal
Notes on antenna hookups
• To prevent noise pickup, keep the AM loop antenna away from the receiver and other components.
• Be sure to fully extend the FM wire antenna.
• After connecting the FM wire antenna, keep it as horizontal as possible.
z
If you have poor FM reception
Use a 75-ohm coaxial cable (not supplied) to connect the receiver to an outdoor FM antenna as shown below.
Outdoor FM antenna
Receiver
FM
75
COAXIAL
AM
ANTENNA
Ground wire (not supplied)
To ground
Important
If you connect the receiver to an outdoor antenna, ground it against lightning. To prevent a gas explosion, do not connect the ground wire to a gas pipe.
5
IN OUT
ç
ç
LINE
L
R
OUTPUT
LINE
L
R
OUTPUT
LINE
INPUT
SUB
WOOFER
IN OUT IN AUDIO IN AUDIO IN AUDIO OUT
AUDIO
OUT
FRONTCENTERSURROUND
AUDIO IN
RL
RL
RL
RL
MULTI CH INMULTI CH IN
DIGITAL
DIGITAL
ANTENNA
CDCD MD/TAPEMD/TAPE VIDEOVIDEO
SPEAKERSSPEAKERS
FRONT
TV/SAT
IN
OPTICAL
DVD/LD
IN
SURROUND
R
L
R
L
CENTER
VIDEO IN
VIDEO IN
VIDEO OUT
VIDEO IN
VIDEO OUT
IMPEDANCE USE 8 – 16
IMPEDANCE USE 8 – 16
ANTENNAANTENNA
AM
FM
75
COAXIAL
TV/SATTV/SAT
MONITOR
DVD/LDDVD/LD
SUB
WOOFER
SUB
WOOFER
COAXIAL
Audio Component Hookups
Hooking Up the Components
MD/TAPE deck
Required cords
Audio cords (not supplied)
When connecting a cord, be sure to match the color-coded pins to the appropriate jacks on the components.
White (L) White (L)
Red (R) Red (R)
CD player
Jacks for connecting audio components
Connect a To the
CD player CD jacks MD deck or Tape deck MD/TAPE jacks
6
Video Component Hookups
TV or satellite tuner DVD or LD player
OUTPUT
AUDIO OUT VIDEO RL
FM
75
COAXIAL
AM
ANTENNA ANTENNAANTENNA
L
R
FRONT
SURROUND
MULTI CH INMULTI CH IN
OUT
CENTER
SUB
WOOFER
TV/SAT
IN
OPTICAL
DIGITAL
DIGITAL
L
R
OUTPUT
AUDIO OUT VIDEO RL
DVD/LD
IN
COAXIAL
IN OUT IN AUDIO IN AUDIO IN AUDIO OUT
CDCD MD/TAPEMD/TAPE VIDEOVIDEO
OUT
VIDEO IN
TV/SATTV/SAT
VIDEO IN
DVD/LDDVD/LD
VIDEO OUT
TV monitor
INPUT
VIDEO
IN
MONITOR
VIDEO OUT
VIDEO IN
AUDIO
OUT
AUDIO IN
SUB
SUB
WOOFER
WOOFER
Required cords
Audio/video cords (not supplied)
When connecting a cord, be sure to match the color-coded pins to the appropriate jacks on the components.
Yellow (video) Yellow (video) White (L/audio) White (L/audio) Red (R/audio) Red (R/audio)
Video cord for connecting a TV monitor (not supplied)
Yellow Yellow
VOLTAGE SELECTORVOLTAGE SELECTOR
120V
240V 220V
SPEAKERSSPEAKERS
RL
RL
IMPEDANCE USE 8 – 16
IMPEDANCE USE 8 – 16
CENTERSURROUND
FRONT
RL
RL
Hooking Up the Components
ç
IN OUT
INPUT OUTPUT
VIDEO
IN
AUDIO
IN
Jacks for connecting video components
Connect a To the
TV or satellite tuner TV/SAT jacks VCR VIDEO jacks DVD or LD player DVD/LD jacks TV monitor MONITOR VIDEO OUT jack
VIDEO
OUT
AUDIO
OUT
ç
L
R
VCR
Note on video component hookups
You can connect your TV’s audio output jacks to the TV/ SAT AUDIO IN jacks on the receiver and apply sound effects to the audio from the TV. In this case, do not connect the TV’s video output jack to the TV/SAT VIDEO IN jack on the receiver. If you are connecting a separate TV tuner (or satellite tuner), connect both the audio and video output jacks to the receiver as shown above.
7
Digital Component Hookups
Hooking Up the Components
Connect the digital output jacks of your DVD player and satellite tuner (etc.) to the receiver’s digital input jacks to bring the multi channel surround sound of a movie theater into your home. To enjoy full effect of multi channel surround sound, five speakers (two front speakers, two surround speakers, and a center speaker) and a sub woofer are required. You can also connect an LD player with an RF OUT jack via an RF demodulator, such as the Sony MOD-RF1 (not supplied).
TV or Satellite
tuner
OUTPUT
VIDEO
OUT
AUDIO
L
R
SURROUND
CENTER
SUB
WOOFER
OUT
L
R
TV/SAT
IN
OPTICAL
OUTPUT
DIGITAL
OPTICAL
COAXIAL
ANTENNA ANTENNAANTENNA
FRONT
FM
75
AM
MULTI CH INMULTI CH IN
DVD player
(etc.)
OUTPUT
DIGITAL
COAXIAL
DIGITAL
DIGITAL
DVD/LD
IN
COAXIAL
L
R
IN OUT IN AUDIO IN AUDIO IN AUDIO OUT
CDCD MD/TAPEMD/TAPE VIDEOVIDEO
VIDEO IN
TV/SATTV/SAT
VIDEO IN
DVD/LDDVD/LD
VIDEO OUT
OUTPUT
VIDEO
OUT
AUDIO
OUT
MONITOR
VIDEO IN
AUDIO IN
WOOFER
WOOFER
VIDEO OUT
AUDIO
OUT
SUB
SUB
Required cords
Optical digital cords (not supplied)
Black Black
Coaxial digital cord (not supplied)
Yellow Yellow
Audio/video cords (not supplied)
When connecting a cord, be sure to match the color-coded pins to the appropriate jacks on the components.
Yellow (video) Yellow (video) White (L/audio) White (L/audio) Red (R/audio) Red (R/audio)
Notes
• The optical and coaxial digital input jacks on the receiver are compatible with sampling frequencies of 32 kHz, 44.1 kHz, and 48kHz.
• The coaxial digital input jack is also compatible with sampling frequency of 96 kHz.
VOLTAGE SELECTORVOLTAGE SELECTOR
120V
240V 220V
SPEAKERSSPEAKERS
RL
RL
IMPEDANCE USE 8 – 16
IMPEDANCE USE 8 – 16
CENTERSURROUND
FRONT
RL
RL
Example of LD player connected via an RF demodulator
Please note that you cannot connect an LD player’s AC-3 RF OUT jack directly to the receiver’s digital input jacks. You must first convert the RF signal to coaxial digital signal. Connect the LD player to the RF demodulator, then connect the RF demodulator’s coaxial digital output to the receiver’s COAXIAL DVD/LD IN jack. Refer to the instruction manual supplied with your RF Demodulator for details on AC-3 RF hookups.
DVD/LD
? / 1
PHONES
VIDEO IN
DISPLAY
PRESET
DIMMER
–+
TUNING
MEMORY SHIFT FM MODE FM AM
–+
TUNING
MULTI CHANNEL DECODING
SET UP
VIDEO DVD/LD TV/SAT
MD/TAPE CD TUNER
MULTI CH IN INPUT MODE
MASTER VOLUME
TREBLE
–+
BASS
+
+
MUTING
NAME
SOUND CONTROL
LEVEL SURR
MENU
SOUND FIELD
MODE 2CH
A.F.D.
ENTER
LD player
VIDEO OUT
AC-3 RF OUT
RF demodulator
DIGITAL DVD/LD IN (COAXIAL)
Note
When making connections as shown above, be sure to set INPUT MODE (qa on page 23) manually. The receiver may not operate correctly if INPUT MODE is set to “AUTO.”
8
MULTI CH IN Hookups
Although this receiver incorporates a multi channel decoder, it is also equipped with MULTI CH IN jacks. These connections allow you to enjoy multichannel software encoded in formats other than Dolby Digital and DTS. If your DVD player is equipped with MULTI CH OUTPUT jacks, you can connect them directly to the receiver to enjoy the sound of the DVD player’s multi channel decoder. Alternatively, the MULTI CH IN jacks can be used to connect an external multi channel decoder. To fully enjoy multi channel surround sound, you will need five speakers (two front speakers, two surround speakers, and a center speaker) and a sub woofer. Refer to the instruction manual supplied with your DVD player, multi channel decoder, etc., for details on the Multi Channel input hookups.
DVD player,
Multichannel decoder, etc.
MULTI CH OUTPUTMULTI CH OUTPUT
SURROUND
CENTER
SUB
WOOFER
FRONT
Required cords
Audio cords (not supplied)
Two for the MULTI CH IN FRONT and SURROUND jacks
White (L) White (L)
Red (R) Red (R)
Monaural audio cords (not supplied)
Two for the MULTI CH IN CENTER and SUB WOOFER jacks
Black Black
Video cord (not supplied)
One for the DVD/LD VIDEO IN jacks (etc.)
Yellow Yellow
Note
When using the connections described below, adjust the level of your surround speakers and sub woofer from the DVD player or multichannel decoder.
Hooking Up the Components
FM
75
COAXIAL
ANTENNA ANTENNAANTENNA
FRONT
AM
L
R
SURROUND
MULTI CH INMULTI CH IN
CENTER
SUB
WOOFER
DIGITAL
DIGITAL
TV/SAT
DVD/LD
IN
IN
VIDEO IN
COAXIAL
OPTICAL
L
R
IN OUT IN AUDIO IN AUDIO IN AUDIO OUT
CDCD MD/TAPEMD/TAPE VIDEOVIDEO
TV/SATTV/SAT
VIDEO IN
DVD/LDDVD/LD
VIDEO OUT
MONITOR
VIDEO OUT
VIDEO IN
AUDIO
AUDIO IN
WOOFER
WOOFER
OUT
SUB
SUB
SPEAKERSSPEAKERS
RL
RL
IMPEDANCE USE 8 – 16
IMPEDANCE USE 8 – 16
CENTERSURROUND
Example of a DVD player hookup using the MULTI CH IN jacks
VIDEO OUT
DVD player
MULTI CH IN
? / 1
PHONES
DISPLAY
DIMMER
PRESET
–+
–+
TUNING
MEMORY SHIFT FM MODE FM AM
DVD/LD VIDEO IN etc.
MULTI CHANNEL DECODING
SET UP
TUNING
MENU
NAME
ENTER
SOUND CONTROL
LEVEL SURR
SOUND FIELD
A.F.D.
MODE 2CH
MULTI CH IN INPUT MODE
–+
+
TREBLE
BASS
SPEAKERS FRONT
VIDEO DVD/LD TV/SAT
MD/TAPE CD TUNER
SPEAKERS
MASTER VOLUME
+
SURROUND/CENTER
MUTING
SUB WOOFER
FRONT
RL
RL
VOLTAGE SELECTORVOLTAGE SELECTOR
120V
240V 220V
Front Speaker (L) Front Speaker (R)
Surround Speaker (L) Surround Speaker (R)
Center Speaker
Active Woofer
Note
See page 12 for details on speaker system hookup.
9
Other Hookups
Hooking Up the Components
FM
75
COAXIAL
DIGITAL
DIGITAL
TV/SAT
IN
AM
ANTENNA ANTENNAANTENNA
FRONT
L
R
SURROUND
MULTI CH INMULTI CH IN
CENTER
SUB
WOOFER
OPTICAL
L
R
* Models of area code E2, E3 only.
Setting the VOLTAGE SELECTOR (models of area code E2, E3 only)
Check that the voltage selector on the rear panel of the player is set to the local power line voltage. If not, set the selector to the correct position using a screwdriver before connecting the AC power cord to a wall outlet.
120 V 240 V 220 V
DVD/LD
IN
VIDEO IN
VIDEO IN
VIDEO OUT
COAXIAL
IN OUT IN AUDIO IN AUDIO IN AUDIO OUT
CDCD MD/TAPEMD/TAPE VIDEOVIDEO
TV/SATTV/SAT
DVD/LDDVD/LD
MONITOR
VIDEO OUT
VIDEO IN
AUDIO
AUDIO IN
WOOFER
WOOFER
OUT
SUB
SUB
VOLTAGE SELECTOR*
VOLTAGE SELECTORVOLTAGE SELECTOR
120V
240V 220V
SPEAKERSSPEAKERS
RL
RL
IMPEDANCE USE 8 – 16
IMPEDANCE USE 8 – 16
CENTERSURROUND
FRONT
RL
RL
To a wall outlet
AC power cord
Connecting the AC power cord
Before connecting the AC power cord of this receiver to a wall outlet:
• Connect the speaker system to the receiver (see page
12).
Connect the AC power cord(s) of your audio/video components to a wall outlet.
Note
If the AC power cord is disconnected for about one week, the receiver’s entire memory will be cleared and the demonstration will start.
10
Hooking Up
SET UP
MENU +/–
and Setting Up the Speaker System
This chapter describes how to hook up your speaker system to the receiver, how to position each speaker, and how to set up your speakers to enjoy multi channel surround sound.
SET UP
–+
TUNING
MULTI CHANNEL DECODING
MENU
NAME
LEVEL SURR
A.F.D.
ENTER
SOUND CONTROL
SOUND FIELD
MODE 2CH
MULTI CH IN INPUT MODE
? / 1
DISPLAY
PRESET
DIMMER
–+
TUNING
PHONES
MEMORY SHIFT FM MODE FM AM
+
TREBLE
–+
BASS
VIDEO DVD/LD TV/SAT
MD/TAPE CD TUNER
MASTER VOLUME
+
MUTING
MENU I/i
Brief descriptions of buttons and control used to set up the speaker system
SET UP button: Press to enter the setup mode when specifying speaker types and distances.
MENU I/i buttons: Use to select parameters after pressing the SET UP button.
MENU +/– buttons: Use to adjust the setting of each parameter.
Hooking Up and Setting Up the Speaker System
11
Speaker System Hookup
Required cords
Speaker cords (not supplied)
One for each front, surround, and center speaker
(+) (+)
Hooking Up and Setting Up the Speaker System
(–) (–)
Monaural audio cord (not supplied)
One for an active woofer
Black Black
FM
75
COAXIAL
DIGITAL
DIGITAL
TV/SAT
DVD/LD
IN
IN
VIDEO IN
TV/SATTV/SAT
VIDEO IN
DVD/LDDVD/LD
ANTENNA ANTENNAANTENNA
FRONT
AM
L
R
SURROUND
MULTI CH INMULTI CH IN
CENTER
SUB
WOOFER
COAXIAL
OPTICAL
L
R
IN OUT IN AUDIO IN AUDIO IN AUDIO OUT
CDCD MD/TAPEMD/TAPE VIDEOVIDEO
VIDEO OUT
MONITOR
VIDEO IN
AUDIO IN
WOOFER
WOOFER
VIDEO OUT
AUDIO
OUT
SUB
SUB
SPEAKERSSPEAKERS
RL
RL
Front speaker (R) Front speaker (L)
]
}
VOLTAGE SELECTORVOLTAGE SELECTOR
120V
240V 220V
IMPEDANCE USE 8 – 16
IMPEDANCE USE 8 – 16
CENTERSURROUND
}
FRONT
RL
RL
]
INPUT
AUDIO
IN
}
]
Active sub woofer Surround speaker (R) Surround speaker (L)
Terminals for connecting the speakers
Connect the To the
Front speakers (8 ohm) Surround speakers (8 ohm) Center speaker (8 ohm) Active sub woofer
SPEAKERS FRONT terminals SPEAKERS SURROUND terminals SPEAKERS CENTER terminals SUBWOOFER AUDIO OUT jack
}
]
}
]
Center speaker
Notes on speaker system hookup
• Twist the stripped ends of the speaker cords about 2/3 inch (10 mm). Be sure to match the speaker cord to the appropriate terminal on the components: + to + and – to –. If the cords are reversed, the sound will be distorted and will lack bass.
• If you use speakers with low maximum input rating, adjust the volume carefully to avoid excessive output on the speakers.
12
To avoid short-circuiting the speakers
Short-circuiting of the speakers may damage the receiver. To prevent this, make sure to take the following precautions when connecting the speakers.
Make sure the stripped ends of each speaker cord does not touch another speaker terminal or the stripped end of another speaker cord.
Examples of poor conditions of the speaker cord
Stripped speaker cord is touching another speaker terminal.
After connecting all the components, speakers, and AC power cord, output a test tone to check that all the speakers are connected correctly. For details on outputting a test tone, see page 18.
If no sound is heard from a speaker while outputting a test tone or a test tone is output from a speaker other than the one whose name is currently displayed on the receiver, the speaker may be short-circuited. If this happens, check the speaker connection again.
To avoid damaging your speakers
Make sure that you turn down the volume before you turn off the receiver. When you turn on the receiver, the volume remains at the level you turn off the receiver.
Hooking Up and Setting Up the Speaker System
Stripped cords are touching each other due to excessive removal of insulation.
13
Performing Initial Setup Operations
Once you have hooked up the speakers and turned on the power, clear the receiver’s memory. Then specify the speaker parameters (size, position, etc.) and perform any other initial setup operations necessary for your system.
Clearing the receiver’s memory
Hooking Up and Setting Up the Speaker System
Before you use your receiver for the first time or when you want to clear the receiver’s memory, do the following. This procedure is not necessary if the demonstration activates when you turn the power on.
?/1
+
TUNING
MULTI CHANNEL DECODING
SET UP
MENU
NAME
LEVEL SURR
A.F.D.
ENTER
SOUND CONTROL
SOUND FIELD
MODE 2CH
MULTI CH IN INPUT MODE
TREBLE
– +
BASS
+
? / 1
DISPLAY
PRESET
DIMMER
+
TUNING
PHONES
MEMORY SHIFT FM MODE FM AM
1 Turn off the receiver. 2 Hold down ?/1 for four seconds.
The currently selected function, then the demonstration message appears in the display and the items including the following are reset or cleared:
• All preset stations are reset or cleared.
• All sound field parameters are reset to their factory settings.
• All index names (of preset stations and program sources) are cleared.
• All adjustments made with the SET UP button are reset to their factory settings.
• The sound field memorized for each program source and preset stations are cleared.
VIDEO DVD/LD TV/SAT
MD/TAPE CD TUNER
MASTER VOLUME
+
MUTING
Performing initial setup operations
Before you use your receiver for the first time, use the SET UP button to adjust settings to correspond to your system. You can set the following items. For details on how to adjust each setting, see the page in parentheses.
• Speaker size and placement (page 15).
• Speaker distance (page 17).
• Select the MULTI CH IN video signal (page 41).
• Whether the display turns off or not when you press DIMMER (page 41).
Demonstration Mode
The demonstration will activate the first time you turn on the power. When the demonstration starts, the following message appears in the display:
“NOW DEMONSTRATION MODE IF YOU FINISH DEMONSTRATION PLEASE PRESS POWER KEY WHILE THIS MESSAGE APPEARS IN THE DISPLAY THANK YOU”
To cancel the demonstration
Press ?/1 to turn the receiver off while the above message is being displayed. The next time you turn the receiver on, the demonstration will not appear.
To view the demonstration
Hold down SET UP and press ?/1 to turn on the power.
Notes
• Running the demonstration will clear the receiver’s memory. For details on what will be cleared, see “Clearing the receiver's memory” on this page.
• There will be no sound when the demonstration mode is activated.
• You cannot cancel demonstration if you did not press ?/1 while the above message is being displayed. To cancel demonstration after the above message appears, press ?/1 twice to activate the demonstration again. Then, press ?/1 while the above message is being displayed.
14
Multi Channel Surround Setup
For the best possible surround sound all speakers should be the same distance from the listening position (A). (However, this unit lets you to place the center speaker up to 5 feet (1.5 meters) closer (B) and the surround speakers up to 15 feet (4.5 meters) closer (C) to the listening position. The front speakers can be placed from 3 to 40 feet (1.0 to
12.0 meters) from the listening position (A).)
You can place the surround speakers either behind you or to the side, depending on the shape of your room (etc.).
When placing surround speakers to your side
B
A A
45°
CC
90°
20°
When placing the surround speakers behind you
B
A A
45°
Specifying the speaker parameters
1 Press ?/1 to turn on the receiver. 2 Press SET UP. 3 Press MENU I/i to select the parameter you want
to adjust.
4 Press MENU +/– to select the setting you want.
The setting is stored automatically.
5 Repeat steps 3 and 4 until you have set all of the
parameters that follow.
z
Normal speaker and Micro Satellite speaker
Choose NORM. SP. if you’re using normal speakers and MICRO SP. if you’re using Micro Satellite speakers. If you choose NORM. SP., you can adjust the speaker size and the sub woofer selection as mentioned below. However, if you choose MICRO SP., the speaker size and the sub woofer selection has been configurated as follows:
Speakers Settings
Front SMALL Center SMALL Surround SMALL Sub Woofer YES
You cannot change the configuration if you choose MICRO SP.
For STR-K402, the speaker size and sub woofer selection has been preset to MICRO SP. according to the supplied speaker system. If you change the speaker system, choose NORM. SP. to adjust the speaker size and sub woofer selection.
Hooking Up and Setting Up the Speaker System
CC
90°
20°
Note
Do not place the center speaker farther away from the listening position than the front speakers.
The setting for Micro Satellite speaker (MICRO SP.) has been programmed to optimize the sound balance. If you use Sony’s Micro Satellite speakers, select MICRO SP. When you use Micro Satellite speaker and the speaker size is set to LARGE, you may not obtain the correct soundstage. The speaker may also be damaged at high volume position.
For STR-DE475, the speaker size and sub woofer selection has been preset to NORM. SP.
The following speaker size setup is applicable for NORM. SP.
15
Multi Channel Surround Setup
x Front speaker size (
L R
)
Initial setting : LARGE
• If you connect large speakers that will effectively reproduce bass frequencies, select “LARGE”. Normally, select “LARGE”.
Hooking Up and Setting Up the Speaker System
• If the sound is distorted, or you feel a lack of surround effects when using multi channel surround sound, select “SMALL” to activate the bass redirection circuitry and output the front channel bass frequencies from the sub woofer.
• When the front speaker is set to “SMALL”, the center and surround speakers are also automatically set to “SMALL” (unless previously set to “NO”).
p Center speaker size (
C
)
Initial setting : LARGE
• If you connect a large speaker that will effectively reproduce bass frequencies, select “LARGE”. Normally, select “LARGE”. However, if the front speakers are set to “SMALL”, you cannot set the center speaker to “LARGE”.
• If the sound is distorted, or you feel a lack of surround effects when using multi channel surround sound, select “SMALL” to activate the bass redirection circuitry and output the center channel bass frequencies from the front speakers (if set to “LARGE”) or sub woofer. *
• If you do not connect the center speaker, select “NO”. The sound of the center channel will be output from the front speakers.*
2
z
About speaker sizes (LARGE and SMALL)
Internally, the LARGE and SMALL settings for each speaker determine whether or not the internal sound processor will cut the bass signal from that channel. When the bass is cut from a channel the bass redirection circuitry sends the corresponding bass frequencies to the sub woofer or other “LARGE” speaker. However, since bass sounds have a certain amount of directionality it best not to cut them, if possible. Therefore, even when using small speakers, you can set them to “LARGE” if you want to output the bass frequencies from that speaker. On the other hand, if you are using a large speaker, but prefer not to have bass frequencies output from that speaker, set it to “SMALL”. If the overall sound level is lower than you prefer, set all speakers to “LARGE”. If there is not enough bass, you can use BASS +/– to boost the bass levels. To adjust the bass, see page 32.
x Surround speaker position (SL SR)*
Initial setting : PL. BEHD. This parameter lets you specify the location of your surround speakers for proper implementation of the Digital Cinema Sound surround modes in the “VIRTUAL” sound fields. Refer to the illustration below.
• Select “PL. SIDE” if the location of your surround speakers corresponds to section A.
• Select “PL. BEHD.” if the location of your surround
1
speakers corresponds to section B.
This setting only effects the surround modes in the “VIRTUAL” sound fields.
p Surround speaker size (SL SR)
Initial setting : LARGE
• If you connect large speakers that will effectively reproduce bass frequencies, select “LARGE”. Normally, select “LARGE”. However, if the front speakers are set to “SMALL”, you cannot set the surround speakers to “LARGE”.
• If the sound is distorted, or you feel a lack of surround effects when using multi channel surround sound, select “SMALL” to activate the bass redirection circuitry and output the surround channel bass frequencies from the sub woofer or other “LARGE” speakers.
• If you do not connect surround speakers, select “NO”.*
z
*1~*3 correspond to the following Dolby Pro Logic modes
*1 NORMAL *2 PHANTOM *3 3 STEREO
90°
A
B
3
45°
20°
A
B
* These parameters are not available when “Surround
speaker size” is set to “NO”.
16
Loading...
+ 36 hidden pages