How it Works
Sony
Loading...
STRDE-997
User Manual
2 pgs234.29 Kb0
Service manual
78 pgs8.97 Mb0
Operating Manual
64 pgs2.38 Mb0
User Manual
64 pgs2.32 Mb0
User Manual
64 pgs2.35 Mb0
User Manual
2 pgs1.48 Mb0
Table of contents
Loading...

Sony STR-DE997 Operating Manual

4-255-361-11(1)
FM Stereo FM/AM Receiver
Operating Instructions
Owner’s Record
The model and serial numbers are located on the rear of the unit. Record the serial number in the space provided below. Refer to them whenever you call upon your Sony dealer regarding this product.
Model No.
Serial No.
STR-DE997
©2004 Sony Corporation
WARNING
To prevent fire or shock hazard, do not expose the unit to rain or moisture.
To prevent fire, do not cover the ventilation of the apparatus with newspapers, table-cloths, curtains, etc. And don’t place lighted candles on the apparatus. To prevent fire or shock hazard, do not place objects filled with liquids, such as vases, on the apparatus.
Do not install the appliance in a confined space, such as a bookcase or built-in cabinet.
Don’t throw away batteries with general house waste; dispose of them correctly as chemical waste.
For customers in the United States
This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
WARNING
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and
receiver.
– Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV
technician for help.
CAUTION
You are cautioned that any changes or modification not expressly approved in this manual could void your authority to operate this equipment.
Note to CATV system installer:
This reminder is provided to call CATV system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.
For customers in Canada
CAUTION
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
NERGY STAR
E mark. As an E
®
is a U.S. registered
NERGY STAR
®
partner, Sony Corporation has determined that this product meets the E
®
TAR
guidelines for energy
S
NERGY
efficiency.
US
2
About This Manual
• The instructions in this manual is for model STR-DE997. Check your model number by looking at the lower right corner of the front panel.
• The instructions in this manual describe the controls on the receiver. You can use the controls on the supplied remote if they have the same or similar names as those on the receiver. For details on the use of your remote, see pages 47–56.
About area codes
The area code of the receiver you purchased is shown on the lower portion of the rear panel (see the illustration below).
FRONT A
R
R
RROUND
OUND BACK
PEAKERS
Any differences in operation, according to the area code, are clearly indicated in the text, for example, “Models of area code AA only”.
This receiver incorporates Dolby* Digital and Pro Logic Surround and the DTS** Digital Surround System.
* Manufactured under license from Dolby
Laboratories. “Dolby”, “Pro Logic” and the double-D symbol are trademarks of Dolby Laboratories.
** “DTS”, “DTS-ES”, “Neo:6” and “DTS 96/24” are
trademarks of Digital Theater Systems, Inc.
+ +
FRONT B
SPEAKERS
L
+–+
L
L
––
L
–
CENTER
AC OUTLET
4-XXX-XXX-XX AA
Area code
US
3
Table of Contents
Getting Started
1: Check how to hookup your
components.......................................5
1a: Connecting components with
digital audio output jacks ...........7
1b: Connecting components with
multi channel output jacks........10
1c: Connecting components with
only analog audio jacks............12
2: Connecting the antennas ...................14
3: Connecting speakers .........................15
4: Connecting the AC power cord ........ 17
5: Setting up the speakers .....................18
6: Adjusting the speaker levels and
balance............................................21
— TEST TONE
Amplifier Operation
Selecting the component.......................23
Listening to multi channel sound..........24
— MULTI CH IN
Listening to FM/AM radio....................24
Presetting radio stations ........................25
Changing the display.............................26
About the indications in the display......27
Enjoying Surround Sound
Using only the front speakers ...............29
Enjoying higher fidelity sound..............30
— AUTO FORMAT DIRECT
Selecting a sound field..........................31
Selecting the surround back decoding
mode ...............................................33
— SURR BACK DECODING
Advanced Adjustments and Settings
Assigning the audio input..................... 35
— DIGITAL ASSIGN
Assigning the component video input .. 36
— COMPONENT VIDEO INPUT ASSIGN
Switching the audio input mode for
digital components ......................... 36
— INPUT MODE
Customizing sound fields ..................... 37
Adjusting the equalizer......................... 38
Advanced settings................................. 39
Other Operations
Naming preset stations and inputs........ 41
Using the Sleep Timer .......................... 41
Selecting the speaker system................ 42
Recording ............................................. 42
Listening to the sound in another
zone ................................................ 43
CONTROL A1II Control System......... 44
Operations Using the Remote RM-LG113
Before you use your remote.................. 47
Remote button description.................... 47
Selecting the command mode of the
remote............................................. 51
Programming the remote...................... 51
Learning the commands of your
components..................................... 54
Performing several commands in
sequence automatically
(Macro Play)................................... 56
Additional Information
Precautions ........................................... 57
Troubleshooting.................................... 58
Specifications ....................................... 61
List of button locations and reference
pages............................................... 63
Index ....................................... Back cover
US
4

Getting Started

1: Check how to hookup your components

Steps 1a through 1c beginning on page 7 describe how to hook up your components to this receiver. Before you begin, refer to “Connectable components” below for the pages which describe how to connect each component. After hooking up all your components, proceed to “2: Connecting the antennas” (page 14).
Connectable components
Component to be connected Page
DVD player
With digital audio output
With multi channel audio output
With analog audio output only
TV monitor
With component video input
With S-Video or composite video input only 13
Satellite tuner
With digital audio output
With analog audio output only
Super Audio CD/CD player
With digital audio output
With multi channel audio output
With analog audio output only
MD/Tape deck
With digital audio output
With analog audio output only
Analog disc turntable 12
Multi channel decoder 10
VCR, camcorder, video game, etc. 13
a)
b)
c)
d)
a)
c)
a)
b)
c)
a)
c)
7–8
10–11
7–8
8 or 11
7–8
7–8
9
10
12
9
12
Getting Started
a)
Model with a DIGITAL OPTICAL OUTPUT or DIGITAL COAXIAL OUTPUT jack, etc.
b)
Model with a MULTI CH OUTPUT jacks, etc. This connection is used to output the audio decoded by the component’s internal multi channel decoder through this receiver.
c)
Model equipped only with AUDIO OUT L/R jacks, etc.
d)
Model with component video (Y, PB/CB/B-Y, PR/CR/R-Y) input jacks.
continued
US
5
Required cords
The hookup diagrams on the subsequent pages assume the use of the following optional connection cords (A to H) (not supplied).
A Audio cord
White (L) Red (R)
B Audio/video cord
Yellow (video) White (L/audio) Red (R/audio)
C Video cord
Yellow
D S-video cord
F Coaxial digital cord
G Monaural audio cord
Black
Tip
Audio cord A can be torn into two monaural audio cords G.
H Component video cord
Green Blue Red
E Optical digital cord
Notes
• Turn off the power to all components before making any connections.
• Be sure to make connections firmly to avoid hum and noise.
• When connecting an audio/video cord, be sure to match the color-coded pins to the appropriate jacks on the components: yellow (video) to yellow; white (left, audio) to white; and red (right, audio) to red.
• When connecting optical digital cords, insert the cord plugs straight in until they click into place.
• Do not bend or tie optical digital cords.
If you have Sony components with CONTROL A1II/CONTROL S jacks
See “CONTROL A1II Control System” on page 44.
US
6
.

1a: Connecting components with digital audio output jacks

Hooking up a DVD player, TV monitor or satellite tuner
For details on the required cords (A–H), see page 6.
1 Connect the audio jacks.
DVD player
OUTPUT
AUDIO
OUT
OUTPUT
DIGITAL
COAXIAL
L
R
AF
Getting Started
DIGITAL
(ASSIGNABLE)
OPTICAL
TV/SAT
IN
MD/ TAPE
IN
MD/
TAPE
OUT
SA-CD/
CD IN
DVD
IN
SA-CD/
CD
IN
COAXIAL
E
OUTPUT
DIGITAL OPTICAL
ANTENNA
SIGNAL GND
PHONO
AM
L
R
SA-CD/CD
L
R
OUT ININ IN
MD/TAPE
S-VIDEO
IN
VIDEO IN
AUDIO IN
TV/SAT
A
OUTPUT
AUDIO
L
R
OUT
CONTROL S
STATUS
STATUS
S-VIDEO
OUT
IN
IN
VIDEO IN
VIDEO OUT
VIDEO IN
L
L
RR
R
AUDIO OUT
AUDIO IN
AUDIO IN
DVD VIDEO 2
L
CENTER
R
SUB
FRONT SURROUND
WOOFER
MULTI CH IN 2
S-VIDEO
S-VIDEO
S-VIDEO
OUT
IN
OUT
VIDEO OUT VIDEO OUT
VIDEO IN
L
MONITOR
SUB
AUDIO OUT
AUDIO IN
WOOFER
PRE OUT
VIDEO 1
LRL
R
SURR
FRONT SURROUND
BACK
MULTI CH IN 1
CTRL A1 II
CENTER
SUB
WOOFER
TV/SAT
IN
CO
L
R
OUT
2ND ZONE
Satellite tuner
Note
You can also listen to the sound of your TV by connecting your TV’s audio output jacks to the TV/SAT AUDIO IN jacks on the receiver. In this case, do not connect the TV’s video output jack to the TV/SAT VIDEO IN jack on the receiver.
continued
US
7
2 Connect the video jacks.
U
R
S
The following illustration shows how to connect a TV or satellite tuner and a DVD player with COMPONENT VIDEO (Y,
P
/CB/B-Y, PR/CR/R-Y) output jacks. Connecting a TV with component
B
video input jacks allows you to enjoy higher quality video.
DIGITAL
(ASSIGNABLE)
OPTICAL
TV/SAT
IN
MD/
TAPE
IN
MD/
TAPE
OUT
SA-CD/
CD IN
DVD
IN
SA-CD/
CD
IN
COAXIAL
OUTPUT
VIDEO
ANTENNA
SIGNAL GND
PHONO
Satellite tuner
OUTPUT
S VIDEO
AM
L
L
R
R
OUT ININ IN
SA-CD/CD
MD/TAPE
OUTPUT
OUTPUT
COMPONENT
PR/CR/R–Y PB/CB/B–Y
S-VIDEO
S-VIDEO
IN
IN
VIDEO IN
VIDEO IN
L
R
AUDIO IN
AUDIO IN
TV/SAT
DVD VIDEO 2
FRONT SURROUND
MULTI CH IN 2
CHD
OUTPUT
VIDEO
S VIDEO
Y
CHHCD D
CONTROL S
S-VIDEO
S-VIDEO
STATUS
STATUS
IN
OUT
OUT
IN
VIDEO OUT
VIDEO IN
VIDEO OUT VIDEO OUT
VIDEO IN
L
L
RR
AUDIO OUT
AUDIO IN
AUDIO OUT
AUDIO IN
VIDEO 1
CENTER
SUB
WOOFER
LRL
FRONT SURROUND
MULTI CH IN 1
OUTPUT
COMPONENT
PR/CR/R–Y PB/CB/B–Y
L
R
INPUT
VIDEO
R
S VIDEO
S-VIDEO
OUT
MONITOR
SUB
WOOFER
PRE OUT
SURR BACK
Y
TV monitor
INPUT
TV/SATINDVD
CTRL A1 II
CENTER
SUB
OUT
WOOFER
2ND ZONE
INPUT
COMPONENT
PR/CR/R–Y PB/CB/B–Y
MONITOR
IN
OUT
COMPONENT VIDEO
(ASSIGNABLE)
+
L
R
Y
Y
S
R
–
R
SUR
DVD player
Tips
• When using the S-video jacks instead of the video jacks, your monitor must also be connected via an S-video jack. S-video signals are on a separate bus from the video signals and will not be output through the video jacks.
• On this receiver, standard video signals can be converted to component video or S-video signals and S-video signals can be converted to component video signals. These upconverted video signals can only be output from the MONITOR VIDEO OUT jack. However, you cannot convert the component video signals to standard video or S-video signals.
US
8
Hooking up an MD/Tape deck or a Super Audio CD/CD player
For details on the required cords (A–H), see page 6.
MD/Tape deck
INPUT OUTPUT
LINE
LINE
L
R
l
IN
l
INOUT
OUT
DIGITAL
OPTICAL IN
OUT
E
EAA
l
l
Getting Started
DIGITAL
(ASSIGNABLE)
OPTICAL
TV/SAT
IN
MD/ TAPE
IN
MD/ TAPE OUT
SA-CD/
CD IN
DVD
IN
SA-CD/
CD IN
COAXIAL
ANTENNA
SIGNAL GND
PHONO
L
R
SA-CD/CD
AM
L
R
OUT ININ IN
MD/TAPE
S-VIDEO
IN
VIDEO IN
AUDIO IN
TV/SAT
CONTROL S
STATUS
STATUS
S-VIDEO
OUT
IN
IN
VIDEO IN
VIDEO OUT
VIDEO IN
L
L
RR
R
AUDIO OUT
AUDIO IN
AUDIO IN
DVD VIDEO 2
L
CENTER
R
SUB
FRONT SURROUND
WOOFER
MULTI CH IN 2
S-VIDEO
S-VIDEO
S-VIDEO
OUT
IN
OUT
VIDEO OUT VIDEO OUT
VIDEO IN
L
MONITOR
SUB
AUDIO OUT
AUDIO IN
WOOFER
PRE OUT
VIDEO 1
LRL
R
SURR
FRONT SURROUND
BACK
MULTI CH IN 1
CTRL A1 II
CENTER
SUB
WOOFER
TV/SAT
IN
CO
L
R
OUT
2ND ZONE
EFA
DIGITAL
OUTPUT
DIGITAL
OPTICAL
COAXIAL
OUT
OUTPUT
LINE
L
R
Super Audio CD/
CD player
If you want to connect several digital components, but cannot find an unused input
See “Assigning the audio input” (page 35).
Tip
All the digital audio jacks are compatible with 32 kHz, 44.1 kHz, 48 kHz and 96 kHz sampling frequencies.
Notes
• You cannot make digital recordings of digital multi channel surround signals.
• I t is not possible to record analog signals to com ponents connected to the MD/TAPE OUT, VIDEO 1 AUDIO OUT or VIDEO 2 AUDIO OUT jacks if you make only digital connections. Likewise, you cannot record digital signals if you make only analog connections. To record analog signals, make analog connections. To record digital signals, make digital connections.
• The sound is not output when you play a Super Audio CD on the Super Audio CD player connected to the SA-CD/CD OPTICAL IN or SA-CD/CD COAXIAL IN jack on this receiver. Connect to the analog input jacks (SA-CD/CD IN jacks). Refer to the operating instructions supplied with the Super Audio CD player.
US
9
1b: Connecting components with multi channel output
L
jacks
1 Connect the audio jacks.
If your DVD or Super Audio CD player is equipped with multi channel output jacks, you can connect it to this receiver’s MULTI CHANNEL INPUT jacks to enjoy the multi channel sound. Alternatively, the multi channel input jacks can be used to connect an external multi channel decoder. For details on the required cords (A
–H), see page 6.
DIGITAL
(ASSIGNABLE)
OPTICAL
TV/SAT
IN
MD/
TAPE
IN
MD/
TAPE
OUT
SA-CD/
CD IN
DVD
IN
SA-CD/
CD
IN
COAXIAL
ANTENNA
SIGNAL GND
PHONO
AM
L
R
SA-CD/CD
L
R
OUT ININ IN
MD/TAPE
S-VIDEO
IN
VIDEO IN
AUDIO IN
TV/SAT
CONTROL S
STATUS
STATUS
S-VIDEO
OUT
IN
IN
VIDEO IN
VIDEO OUT
VIDEO IN
L
L
RR
R
AUDIO OUT
AUDIO IN
AUDIO IN
DVD VIDEO 2
L
CENTER
R
SUB
FRONT SURROUND
WOOFER
MULTI CH IN 2
S-VIDEO
S-VIDEO
S-VIDEO
OUT
IN
OUT
VIDEO OUT VIDEO OUT
VIDEO IN
L
MONITOR
SUB
AUDIO OUT
AUDIO IN
WOOFER
PRE OUT
VIDEO 1
LRL
R
SURR
FRONT SURROUND
BACK
MULTI CH IN 1
CTRL A1 II
CENTER
SUB
WOOFER
TV/SAT
IN
CO
L
R
OUT
2ND ZONE
MULTI CHANNE INPUT 1
MULTI CHANNEL INPUT 2
Tips
• This connection also allows you to enjoy software with multi channel audio recorded in formats other than the
AAGG
L
R
Super Audio CD player,
CENTER
SUB
FRONT
SURROUND
WOOFER
MULTI CH OUT
DVD player,
Multi channel decoder, etc.
Dolby Digital and DTS.
• Make connections to either the MULTI CHANNEL INPUT 1 or MULTI CHANNEL INPUT 2 jacks according to the number of audio output jacks of the component.
Note
When you make connections to the MULTI CHANNEL INPUT jacks, you will need to adjust the level of the surround speakers and sub woofer using the controls on the connected component.
10
US
2 Connect the video jacks.
R
S
The following illustration shows how to connect a DVD player with COMPONENT VIDEO (Y, P
/B-Y, PR/CR/R-Y) output jacks. Connecting a TV with component video input jacks allows you
B/CB
to enjoy higher quality video.
TV monitorDVD player
Getting Started
PR/CR/R–Y PB/CB/B–Y
TV/SATINDVD
IN
COMPONENT VIDEO
(ASSIGNABLE)
L
R
OUT
2ND ZONE
INPUT
COMPONENT
MONITOR
OUT
+
Y
HC
Y
SU
R
–
R
SUR
DIGITAL
(ASSIGNABLE)
OPTICAL
TV/SAT
IN
MD/
TAPE
IN
MD/
TAPE
OUT
SA-CD/
CD IN
DVD
IN
SA-CD/
CD
IN
COAXIAL
OUTPUT
VIDEO
ANTENNA
SIGNAL GND
PHONO
L
R
SA-CD/CD
AM
OUTPUT
S VIDEO
TV/SAT
L
R
OUT ININ IN
MD/TAPE
OUTPUT
COMPONENT
PR/CR/R–Y PB/CB/B–Y
Y
HCD D
CONTROL S
STATUS
S-VIDEO
IN
VIDEO IN
AUDIO IN
L
R
STATUS
S-VIDEO
OUT
IN
IN
VIDEO IN
VIDEO OUT
VIDEO IN
L
RR
AUDIO OUT
AUDIO IN
AUDIO IN
DVD VIDEO 2
L
CENTER
R
SUB
FRONT SURROUND
WOOFER
MULTI CH IN 2
INPUT
VIDEO
S-VIDEO
S-VIDEO
S-VIDEO
OUT
IN
OUT
VIDEO OUT VIDEO OUT
VIDEO IN
L
MONITOR
SUB
AUDIO OUT
AUDIO IN
WOOFER
PRE OUT
VIDEO 1
LRL
R
SURR
FRONT SURROUND
BACK
MULTI CH IN 1
INPUT
S VIDEO
CTRL
A1 II
CENTER
SUB
WOOFER
Tips
• When using the S-video jacks instead of the video jacks, your monitor must also be connected via an S-video jack. S-video signals are on a separate bus from the video signals and will not be output through the video jacks.
• On this receiver, standard video signals can be converted to component video or S-video signals and S-video signals can be converted to component video signals. These upconverted video signals can only be output from the MONITOR VIDEO OUT jack. However, you cannot convert the component video signals to standard video or S-video signals.
11
US

1c: Connecting components with only analog audio jacks

Hooking up audio components
For details on the required cords (A–H), see page 6.
Turntable
A
DIGITAL
(ASSIGNABLE)
OPTICAL
TV/SAT
IN
MD/
TAPE
IN
MD/
TAPE
OUT
SA-CD/
CD IN
DVD
IN
SA-CD/
CD
IN
COAXIAL
ANTENNA
SIGNAL GND
PHONO
AM
R
SA-CD/CD
LL
R
OUT ININ IN
MD/TAPE
S-VIDEO
IN
VIDEO IN
AUDIO IN
TV/SAT
CONTROL S
CONTROL S
STATUS
STATUS
S-VIDEO
OUT
IN
IN
VIDEO IN
VIDEO OUT
VIDEO IN
L
L
RR
R
AUDIO OUT
AUDIO IN
AUDIO IN
DVD VIDEO 2
L
CENTER
R
SUB
FRONT SURROUND
WOOFER
MULTI CH IN 2
S-VIDEO
S-VIDEO
S-VIDEO
OUT
IN
OUT
VIDEO OUT VIDEO OUT
VIDEO IN
L
MONITOR
SUB
AUDIO OUT
AUDIO IN
WOOFER
PRE OUT
VIDEO 1
LRL
R
SURR
FRONT SURROUND
BACK
MULTI CH IN 1
l
IN
l
A
LINE
L
R
MD/Tape deck
A
OUTPUT
LINE
Super Audio CD/CD
player
OUT
A
INPUT OUTPUT
L
R
LINE
Note
If your turntable has a ground wire, connect it to the U SIGNAL GND terminal.
CTRL
A1 II
CENTER
SUB
WOOFER
TV/SAT
IN
CO
L
R
OUT
2ND ZONE
12
US
Hooking up video components
R
S
If you connect your TV to the MONITOR jacks, you can watch the video from the selected input (page 23). You can also display the SET UP, LEVEL, EQUALIZER and CUSTOMIZE menu settings and sound fields on your TV by pressing ON SCREEN. For details on the required cords (A–H), see page 6.
VCR
OUTPUTINPUT
VIDEO
VIDEO
OUT
OUT
AUDIO
IN
IN
AUDIO
L
OUT
L
R
BB DC
IN
L
TV monitor
INPUT
INPUT
VIDEO
S VIDEO
Getting Started
To the VIDEO 3 INPUT jacks (Front panel)
DIGITAL
(ASSIGNABLE)
OPTICAL
TV/SAT
IN
MD/
TAPE
IN
MD/
TAPE
OUT
SA-CD/
CD IN
DVD
IN
SA-CD/
CD IN
COAXIAL
B D
Camcorder or
video game
ANTENNA
SIGNAL GND
PHONO
AM
L
R
SA-CD/CD
TV/SAT
L
R
OUT ININ IN
MD/TAPE
S-VIDEO
IN
VIDEO IN
AUDIO IN
L
R
CONTROL S
STATUS
S-VIDEO
OUT
IN
VIDEO IN
VIDEO OUT
L
R
AUDIO OUT
AUDIO IN
DVD VIDEO 2
L
R
FRONT SURROUND
MULTI CH IN 2
S-VIDEO
STATUS
OUT
IN
VIDEO IN
VIDEO OUT VIDEO OUT
AUDIO IN
AUDIO OUT
VIDEO 1
CENTER
SUB
FRONT
WOOFER
OUT
L
B
VIDEO
IN
AUDIO
IN
S-VIDEO
S-VIDEO
OUT
IN
VIDEO IN
L
MONITOR
R
SUB
AUDIO IN
WOOFER
PRE OUT
LRL
R
SURR
SURROUND
BACK
MULTI CH IN 1
L
BDD
OUTPUTINPUT
VIDEO
OUT
AUDIO
OUT
L
R
IN
CTRL A1 II
CENTER
SUB
WOOFER
VCR
TV/SATINDVD
IN
COMPONENT VIDEO
(ASSIGNABLE)
L
R
OUT
2ND ZONE
OUTLIN
INPUT
S VIDEO
MONITOR
OUT
OUTPUT
S VIDEO
Y
SU
R
+
–
R
SUR
L
13
US

2: Connecting the antennas

Connect the supplied AM loop antenna and FM wire antenna.
AM loop antenna (supplied)
FM wire antenna (supplied)
DIGITAL
(ASSIGNABLE)
OPTICAL
TV/SAT
IN
MD/
TAPE
IN
MD/
TAPE
OUT
SA-CD/
CD IN
DVD
IN
SA-CD/
CD
IN
COAXIAL
ANTENNA
SIGNAL GND
PHONO
AM
L
R
SA-CD/CD
L
R
OUT ININ IN
MD/TAPE
S-VIDEO
VIDEO IN
AUDIO IN
TV/SAT
IN
CONTROL S
CONTROL S
STATUS
STATUS
S-VIDEO
OUT
IN
IN
VIDEO IN
VIDEO OUT
VIDEO IN
L
L
RR
R
AUDIO OUT
AUDIO IN
AUDIO IN
DVD VIDEO 2
L
CENTER
R
SUB
FRONT SURROUND
WOOFER
MULTI CH IN 2
S-VIDEO
S-VIDEO
S-VIDEO
OUT
IN
OUT
VIDEO OUT VIDEO OUT
VIDEO IN
L
MONITOR
SUB
AUDIO OUT
AUDIO IN
WOOFER
PRE OUT
VIDEO 1
LRL
R
SURR
FRONT SURROUND
BACK
MULTI CH IN 1
CTRL A1 II
CENTER
SUB
WOOFER
TV/SAT
IN
CO
L
R
OUT
2ND ZONE
*
*
The shape of the connector varies depending on the area code.
Notes
• To prevent noise pickup, keep the AM loop antenna away from the receiver and other components.
• Be sure to fully extend the FM wire antenna.
• After connecting the FM wire antenna, keep it as horizontal as possible.
• Do not use the U SIGNAL GND terminal for grounding the receiver.
14
US

3: Connecting speakers

Connect your speakers to the receiver. This receiver allows you to use a 7.1 channel speaker system. To fully enjoy theater-like multi channel surround sound requires five speakers (two front speakers, a center speaker, and two surround speakers) and a sub woofer (5.1 channel). You can enjoy high fidelity reproduction of DVD software recorded in the Surround EX format if you connect one additional surround back speaker (6.1 channel) or two surround back speakers (7.1 channel) (see “Selecting the surround back decoding mode” on page 33).
Example of 7.1 channel speaker system configuration
Center speaker
Front speaker (Right)
Surround speaker (Right)
Front speaker (Left)
Sub woofer
Getting Started
Surround speaker (Left)
Surround back speaker (Right)
Surround back speaker (Left)
Tips
• When you connect 6.1 channel speaker system, place the surround back speaker behind the listening position (see “When placing only one surround back speaker” illustration on page 19).
• Since the sub woofer does not emit highly directional signals, you can place it wherever you want.
continued
15
US
Required cords
A Speaker cords (not supplied)
(+) (–)
B Monaural audio cord (not supplied)
Black
Surround speaker
(Right)
Ee
S-VIDEO
S-VIDEO
OUT
IN
VIDEO IN
VIDEO OUT
L
R
AUDIO OUT
AUDIO IN
VIDEO 1
LRL
FRONT SURROUND
MULTI CH IN 1
S-VIDEO
VIDEO OUT
MONITOR
WOOFER
PRE OUT
R
INPUT
AUDIO
IN
OUT
SUB
SURR BACK
CTRL A1 II
CENTER
SUB
WOOFER
B
Surrond speaker
(Left)
Ee
A
MONITOR
TV/SATINDVD
OUT
IN
COMPONENT VIDEO
(ASSIGNABLE)
+ +
L
R
OUT
2ND ZONE
E
Front speaker
(Right)
Ee
A
Y
R
R
SURROUND
SURROUND BACK
SPEAKERS
A
FRONT A
++
SPEAKERS
–
e
––
FRONT B
LR
––
LR
CENTER
E
L
L
+
A
Front speaker
(Left)
Ee
AA
SPEAKERS FRONT B*
AC OUTLET
A
E
e
e
Sub woofer
Surround back
speaker (Right)**
Surround back
speaker (Left)**
Center speaker
* If you have an additional front speaker system, connect them to the SPEAKERS FRONT B terminals. You can
select the front speakers you want to use with SPEAKERS (OFF/A/B/A+B) button. For details, see “Selecting the speaker system” (page 42).
** If you connect only one surround back speaker, connect it to the SPEAKERS SURROUND BACK L terminals.
US
16
4: Connecting the AC
b
power cord

Connecting the AC power cord

Connect the AC power cord to a wall outlet.
T A
L
+
–
L
T B
+
–
CENTER
AC OUTLET
* The configuration, shape, and number of AC outlets
vary according to the area code.
Notes
• The AC OUTLET(s) on the rear of the receiver is a switched outlet, which supplies power to the connected component only while the receiver is turned on.
• Make sure that the total power consumption of the component(s) connected to the receiver’s AC OUTLET(s) does not exceed the wattage stated on the rear panel. Do not connect high-wattage electrical home appliances such as electric irons, fans, or TVs to this outlet. This may cause a malfunction.
AC OUTLET
*
AC power cord
To a wall outlet
Performing initial setup operations
Before using the receiver for the first time, initialize the receiver by performing the following procedure. This procedure can also be used to return settings you have made to their factory defaults. Use the buttons on the receiver for the operation.
1 Press ?/1 to turn off the receiver. 2 Hold down ?/1 for 5 seconds.
“PUSH ENTER” flashes in the display.
3 Press ENTER.
“MEMORY CLEARING” appears in the display for a while, then “MEMORY CLEARED” appears. The following are reset to their factory settings.
• All settings in the SET UP, LEVEL, EQUALIZER and CUSTOMIZE menus.
• The sound field memorized for each input and preset station.
• All sound field parameters.
• All preset stations.
• All index names for inputs and preset stations.
• MASTER VOLUME –/+ is set to “VOLUME MIN”.
Getting Started
17
US

5: Setting up the speakers

You can use the SET UP menu to set the size, distance and location of the speakers connected to this receiver.
1 Press ?/1 to turn on the receiver. 2 Press MAIN MENU repeatedly to select
“SET UP”.
3 Turn MENU to select the parameter you
want to adjust.
For details, see “Speaker setup parameters” below.
Note
Some speaker setup items may appear dimmed in the display. This means that they have been adjusted automatically due to other speaker settings or may not be adjustable.
4 Turn –/+ to select the setting you want.
The setting is entered automatically.
5 Repeat steps 3 and 4 until you have set
all of the items that follow.
Speaker setup parameters
The initial settings are underlined.
x EASY SETUP XXX (Speaker easy setup)
•YES
If you want to set up your speakers automatically, select “YES”. You can select a pre-defined speaker pattern (see the supplied “Easy Setup Guide”).
•NO If you want to adjust the settings of each
speaker manually, select “NO”.
x SP PATTERN X–X
(Speaker setup pattern)
When “EASY SETUP” is set to “YES”, select the speaker setup pattern. Turn –/+ to select the speaker setup pattern and press ENTER to enter the selection. Check your speaker pattern using the supplied “Easy Setup Guide”.
x SUB WOOFER XXX
(Sub woofer selection)
•YES If you connect a sub woofer, select “YES”.
•NO If you did not connect a sub woofer, select
“NO”. The front speakers are automatically set to “LARGE” and you cannot change this setting. This activates the bass redirection circuitry and outputs the LFE signals from other speakers.
• In order to take full advantage of the Dolby Digital bass redirection circuitry, we recommend that you set the cut off frequency on the sub woofer as high as possible.
x FRONT SP XXXXX
(Front speakers size)
• LARGE If you connect large speakers that will
effectively reproduce bass frequencies, select “LARGE”. Normally, select “LARGE”.
•SMALL If the sound is distorted, or you feel a lack of
surround effects when using multi channel surround sound, select “SMALL” to activate the bass redirection circuitry and output the front channel bass frequencies from the sub woofer. When the front speakers are set to “SMALL”, the center, surround and surround back speakers are also automatically set to “SMALL” (unless previously set to “NO”).
x CTR SP XXXXX
(Center speaker size)
• LARGE If you connect a large speaker that will
effectively reproduce bass frequencies, select “LARGE”. Normally, select “LARGE”. However, if the front speakers are set to “SMALL”, you cannot set the center speaker to “LARGE”.
•SMALL If the sound is distorted, or you feel a lack of surround effects when using multi channel
surround sound, select “SMALL” to activate the bass redirection circuitry and output the center channel bass frequencies from the front speakers (if set to “LARGE”) or sub woofer.
a)
18
US
•NO If you did not connect a center speaker, select
“NO”. The sound of the center channel will be output from the front speakers.
b)
x SURR SP XXXXX
(Surround speakers size)
• LARGE If you connect large speakers that will
effectively reproduce bass frequencies, select “LARGE”. Normally, select “LARGE”. However, if the front speakers are set to “SMALL”, you cannot set the surround speakers to “LARGE”.
•SMALL If the sound is distorted, or you feel a lack of surround effects when using multi channel
surround sound, select “SMALL” to activate the bass redirection circuitry and output the surround channel bass frequencies from the sub woofer or other “LARGE” speakers.
•NO If you did not connect surround speakers, select “NO”.
c)
x SB SP XXXXXX
(Surround back speakers selection)
When the surround speakers size parameter is set to “NO”, the surround back speakers selection parameter is also automatically set to “NO” and the setting cannot be changed.
• DUAL If you connect two surround back speakers,
select “DUAL”. The sound will be output to a maximum of 7.1 channels.
•SINGLE If you connect only one surround back speaker, select “SINGLE”. The sound will be
output to a maximum of 6.1 channels.
•NO If you did not connect surround back
speakers, select “NO”.
Tips
• a)–c) correspond to the following Dolby Pro Logic modes a) NORMAL b) PHANTOM c) 3 STEREO
• The “LARGE” and “SMALL” settings for each speaker determine whether the internal sound processor will cut the bass signal from that channel. When the bass is cut from a channel, the bass redirection circuitry sends the corresponding bass frequencies to the sub woofer or other “LARGE” speakers. However, since bass sounds have a certain amount of directionality, it is best not to cut them, if possible. Therefore, even when using small speakers, you can set them to “LARGE” if you want to output the bass frequencies from that speaker. On the other hand, if you are using a large speaker, but prefer not to have bass frequencies output from that speaker, set it to “SMALL”. If the overall sound level is lower than you prefer, set all speakers to “LARGE”. I f there is not enough bass, you can use the BASS parameter in the EQUALIZER menu to boost the bass levels. To adjust the bass, see page 38.
x FRONT DIST. XX ft.
(Front speaker distance)
Initial setting: 10 ft.
Lets you set the distance from your listening position to the front speakers (A). You can adjust from 3 to 23 feet in 1 foot steps.
If both front speakers are not placed an equal distance from your listening position, set the distance to the closest speaker.
When placing only one surround back speaker
B
A
CC
A
30˚30˚
100˚-120˚100˚-120˚
Getting Started
D
continued
US
19
When placing two surround back speakers (The angle E should be the same)
B
AA
30˚30˚
100˚-120˚100˚-120˚
E
E
E
DD
x CTR DIST. XX ft.
(Center speaker distance)
Initial setting: 10 ft.
Lets you set the distance from your listening position to the center speaker. Center speaker distance should be set from a distance equal to the front speaker distance (A) to a distance 5 feet closer to your listening position (B).
x SURR DIST. XX ft.
(Surround speaker distance)
Initial setting: 10 ft.
Lets you set the distance from your listening position to the surround speakers. Surround speaker distance should be set from a distance equal to the front speaker distance (A) to a distance 15 feet closer to your listening position (C).
If both surround speakers are not placed an equal distance from your listening position, set the distance to the closest speaker.
x SB DIST. XX ft.
(Surround back speaker distance)
Initial setting: 10 ft.
Lets you set the distance from your listening position to the surround back speaker. Surround back speaker distance should be set from a distance equal to the front speaker distance (A) to a distance 15 feet closer to your listening position (D).
If you connect two surround back speakers and both surround back speakers are not placed an equal distance from your listening position, set the distance to the closest speaker.
Tip
The receiver lets you to input the speaker position in terms of distance. However, it is not possible to set the center speaker further than the front speakers. Also, the center speaker cannot be set more than 5 feet closer than the front speakers.
Likewise, the surround speakers and the surround back speakers cannot be set further away from the listening position than the front speakers. And they can be no more than 15 feet closer.
This is because incorrect speaker placement is not conducive to the enjoyment of surround sound.
Please note that, setting the speaker distance closer than the actual location of the speakers will cause a delay in the output of the sound from that speaker. In other words, the speaker will sound like it is further away.
For example, setting the center speaker distance 3–6 feet closer than the actual speaker position will create a fairly realistic sensation of being “inside” the screen. If you cannot obtain a satisfactory surround effect because the surround speakers are too close, setting the surround speaker distance closer (shorter) than the actual distance will create a larger sound stage.
Adjusting these parameter while listening to the sound often results in much better surround sound. Give it a try!
x PL. XXXX/XXXX
(Surround speaker position)*
Lets you specify the location of your surroun d speakers for proper implementation of the surround effects in the Cinema Studio EX modes (page 31).
120˚
100˚
A
B
A
B
20
D
C
US
D
60
C
30
Loading...
+ 44 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use