Page 1
SA-VE155/WMS155/
SS-MS155
SERVICE MANUAL
Ver 1.0 2004. 05
SA-WMS155 SS-MS155
• SA-VE155 consists of the following models respectively.
SUBWOOFER SA-WMS155
FRONT, CENTER AND
SURROUND SPEAKER
SS-MS155
AEP Model
UK Model
E Model
SS-MS155 (front, center and surround speakers)
Speaker system Full range, magnetically
shielded
Speaker units 7 cm, cone type
Enclosure type Closed type
Rated impedance 8 ohms
Power handling capacity
Maximum input power: 100 W
Sensitivity level 83 dB (1 W, 1 m)
Frequency range 120 Hz - 20,000 Hz
Dimensions (w/h/d) Approx. 91 × 96 × 102 mm,
including front grille
Mass Approx. 650 g each
SPECIFICATIONS
SA-WMS155 (subwoofer)
Speaker system Active subwoofer,
magnetically shielded
Speaker unit Woofer: 16 cm, cone type
Enclosure type Bass refl ex
Reproduction frequency range
32 Hz - 200 Hz
Continuous RMS power output
55 W (4 ohms, 100 Hz,
10 % THD)
Input
LINE IN (input pin jack)
General
Power requirements 220 - 240 V AC, 50/60 Hz
Power consumptions 45 W
Dimensions (w/h/d) E model:
Approx. 210 × 355 × 335
mm
AEP, UK model:
Approx. 210 × 355 × 330
mm
Mass Approx. 8 kg
Supplied accessories
Foot pads (20)
Audio connecting cord (1)
Speaker connecting cords, 10 m (2)
Speaker connecting cords, 3.5 m (3)
Design and specifi cations are subject to change
without notice.
9-877-869-01
2004E04-1
© 2004. 05
MICRO SATELLITE SPEAKER SYSTEM
Sony Corporation
Home Audio Company
Published by Sony Engineering Corporation
1
Page 2
SA-VE155/WMS155/SS-MS155
UNLEADED SOLDER
•
Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40°C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350°C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
TABLE OF CONTENTS
1. GENERAL
Location of Controls ................................................................ 3
2. DIAGRAMS
2-1. Note for Printed Wiring Boards and
Schematic Diagrams ............................................................ 3
2-2. Circuit Boards Location ...................................................... 3
2-3. Printed Wiring Boards (SA-WMS155) ............................... 4
2-4. Schematic Diagram (SA-WMS155) ................................... 5
2-5. IC Block Diagram ............................................................... 6
3. EXPLODED VIEWS .......................................................... 7
4. ELECTRICAL PARTS LIST ........................................... 8
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PA RT NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
2
Page 3
LOCATION OF CONTROL
d
SECTION 1
GENERAL
This section is extracted
from instruction manual.
SA-VE155/WMS155/SS-MS155
SECTION 2
DIAGRAMS
2-1. NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
WOOFER OUT
Ee
CENTER
Center
Centre
A
Front (Right)
Avant (droite)
Ampli er
Ampli cateur
Subwoofer
Caisson de grave
LINE IN
Ee
3.5m
3,5m
10m
Surround
(Right)
Effet surround
Ee
(droite)
E
Foot pads
Tampons
autocollants
English
WARNING
To prevent fi re or shock hazard, do not expose the
unit to rain or moisture.
To prevent fi re, do not cover the ventilation of the apparatus
with news papers, table-cloths, curtains, etc. And don’t place
lighted candles on the apparatus.
To prevent fi re or shock hazard, do not place objects fi lled with
liquids, such as vases, on the apparatus.
To avoid electrical shock, do not open the cabinet. Refer
servicing to qualifi ed personnel only.
Do not install the appliance in a confi ned space, such as a
bookcase or built-in cabinet.
About this manual
The SA-VE155 is a 5.1 channel speaker system consisting of
two front speakers, one center speaker, two surround speakers,
and one subwoofer. It supports Sony Digital Cinema Sound,
Dolby* Pro Logic, and Dolby Digital etc., and is thus geared
towards the enjoyment of movies.
* “Dolby” and the double-D symbol are trademarks of Dolby
Laboratories.
Precautions
On safety
• Before operating the system, be sure that the operating
voltage of the system is identical with that of your local
power supply.
• The unit is not disconnected from the AC power source
(mains) as long as it is connected to the wall outlet, even if
the unit itself has been turned off.
• Unplug the system from the wall outlet if it is not to be used
for an extended period of time. To disconnect the cord, pull
the cord by grasping the plug. Never pull the cord itself.
• Should any liquid or solid object fall into the system, unplug
the system’s power cord and have the system checked by
qualifi ed personnel before operating it any further.
• AC power cord must be changed only at the qualifi ed service
shop.
On operation
• Do not drive the speaker system with a continuous wattage
exceeding the maximum input power of the system.
• If the polarity of the speaker connections are not correct,
the bass tones will be weak and the position of the various
instruments obscure.
• Contact between bare speaker wires at the speaker terminals
may result in a short circuit.
• Before connecting, turn off the amplifi er to avoid damaging
the speaker system.
• The speaker grille cannot be removed. Do not attempt to
remove the grille on the speaker system. If you try to remove
it, you may damage the speaker.
• The volume level should not be turned up to the point of
distortion.
If you encounter color irregularity on a
nearby TV screen
This speaker system is magnetically shielded to allow it to be
installed near a TV set. However, color irregularities may still
be observed on certain types of TV sets.
If color irregularity is observed...
c Turn off the TV set, then turn it on again after 15 to 30
minutes.
If color irregularity is observed again...
c Place the speakers further away from the TV set.
If howling occurs
Reposition the speakers or turn down the volume on the
amplifi er.
On placement
• Do not set the speakers in an inclined position.
• Do not place the speakers in locations that are:
— Extremely hot or cold
— Dusty or dirty
—Very humid
— Subject to vibrations
— Subject to direct sunlight
• Use caution when placing the speaker on a specially
treated (waxed, oiled, polished, etc.) fl oor, as staining or
discoloration may result.
On cleaning
Clean the speaker cabinets with a soft cloth lightly moistened
with a mild detergent solution or water. Do not use any type
of abrasive pad, scouring powder or solvent such as alcohol or
benzine.
If you have any questions or problems concerning your speaker
system, please consult your nearest Sony dealer.
Front (Left)
Ee
Avant (gauche)
Ee
3.5m
3.5m
3,5m
3,5m
FRONT
RRL
eEEe
L
SURROUND
Surround
(Left)
Effet surround
(gauche)
10m
Ee
WS-WV10D
WS-FV11
(for front, center and surround speakers)
(pour les enceintes avant, centrale et ‡ effet
surround)
Hooking up the system
Connect the speaker system to the speaker output terminals of
an amplifi er (A).
Make sure power to all components (included the subwoofer)
is turned off before starting the hook-up.
Notes (B)
• Make sure the plus (+) and the minus (–) terminals on the
speakers are matched to the corresponding plus (+) and
minus (–) terminals on the amplifi er.
• Be sure to tighten the screws of the speaker terminals
securely as loose screws may become a source of noise.
• Make sure all connections are fi rm. Contact between bare
speaker wires at the speaker terminals may cause a short
circuit.
• For details regarding the connections on the amplifi er side,
refer to the manual that was provided with your amplifi er.
Tip
Black or black striped wires are minus (–) in polarity, and
should be connected to the minus (–) speaker terminals.
Positioning the speakers
Location of each speaker (C)
Each speaker should face the listening position. Better
surround effect will result if all speakers are set at the same
distance from the listening position.
Place the front speakers at a suitable distance to the left and
right of the television.
Place the subwoofer on either side of the television.
Place the center speaker on the top-center of the TV set.
The placement of surround speakers greatly depends on the
confi guration of the room. The surround speakers may be
placed on both sides of the listening position A or behind the
listening position B.
Setting the speakers
To prevent speaker vibration or movement while listening,
attach the supplied foot pads to the bottom four corners of the
front speakers, center speaker and surround speakers (D).
Setting the center speaker (E)
Set the center speaker fi rmly on top of the TV set, making sure
it is completely level.
Setting the speakers using the optional speaker
stands (F)
For greater fl ex ibility in the positioning of the speakers, use the
optional WS-FV11 or WS-WV10D speaker stand (available
only in certain countries).
To hang the front, center and surround speakers
with a hook (not supplied) on the wall (G)
You are responsible for the proper selection and use of
mounting hardware that you purchase at hardware stores, and
for the proper and safe mounting of the speakers.
Tip
The height of the front speakers should be adjusted to about the
center of the TV screen (H).
Setting the amplifi er
When connecting to an amplifi er with internal multi channel
decoders (Dolby Digital, DTS**, etc.), you should use the
setup menus for the amplifi er to specify the parameters of your
speaker system.
See the table below for the proper settings. For details on the
setting procedure, refer to the manual that was provided with
your amplifi er.
Speaker setup
For Set to
Front speakers SMALL
Center speaker SMALL
Surround speakers SMALL
Subwoofer ON (or YES)
If you use the amplifi er with adjustable crossover frequency,
it is recommended to select 150 Hz (or close to this fi gure) as
the crossover frequency for your front, center and surround
speakers.
** “DTS” and “DTS Digital Surround” are registered
trademarks of Digital Theater Sys tems, Inc.
B
e
e
E
e
E
E
E
G
Listening to the sound (I)
First, turn down the volume on the amplifi er. The volume
should be set to minimum before you begin playing the
program source.
1
Turn on the amplifi er and select the program
source.
2
Press POWER on the subwoofer.
The POWER indicator on the subwoofer
lights up green.
3
Play the program source.
Note (Singaporean model only)
Protection circuit is contained in the satellite speakers. If the
speakers are overdriven for certain minutes, the protection
circuit will automatically reduce the sound volume. In the case,
stop the program source for 2-3 minutes. Before playing the
source again, turn down the volume level of the amplifi er.
Adjusting the subwoofer (I)
Rotate LEVEL to adjust the volume.
Set the volume level to best suit your pref er ence
according to the program source.
Notes
• Some amplifi er functions for enhancing the sound may cause
distortion in the subwoofer. If such distortion occurs, turn off
those functions.
• To enjoy high-quality sound, do not turn the subwoofer
volume too high.
Troubleshooting
Should you encounter a problem with your speaker system,
check the following list and take the indicated measures. If the
problem persists, consult your nearest Sony dealer.
There is no sound from the speaker system.
• Make sure all the connections have been correctly
made.
• Make sure the volume on the amplifi er has been
turned up properly.
• Make sure the program source selector on the
amplifi er is set to the proper source.
• Check if headphones are connected. If they are,
disconnect them.
There is distortion in the subwoofer sound
output.
• Check if any sound-enhancing functions have been
activated on the amplifi er. If they have, turn them
off.
There is hum or noise in the speaker output.
• Make sure all the connections have been correctly
made.
• Make sure none of the audio components are
positioned too close to the TV set.
The sound has suddenly stopped.
• Make sure all the connections have been correctly
made. Contact between bare speaker wires at the
speaker terminals may cause a short circuit.
C
Front (Left)
e
Hook
Crochet
Avant
(gauche)
Surround (Left)
Effet surround (gauche)
HF
Center
Centre
Subwoofer
Caisson de grave
Front (Right)
Surround (Right)
BB
Effet surround (droite)
Avant (droite)
AA
I
D
POWER indicator
Voyant POWER
Foot pads
Tampons autocollants
LINE IN
LEVEL
POWER
BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is printed
in each block.)
For schematic diagrams.
Note:
• All capacitors are in µF unless otherwise noted. (p: pF)
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1/
specified.
f
•
: internal component.
• C : panel designation.
Note: The components identified by mark 0 or dotted line
with mark 0 are critical for safety.
Replace only with part number specified.
• A : B+ Line.
• B : B– Line.
•Voltages are dc with respect to ground under no-signal
(detuned) conditions.
no mark : Power on
•Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production tolerances.
• Signal path.
F : AUDIO
4
W or less unless otherwise
For printed wiring boards.
Note:
• X : parts extracted from the component side.
• Y : parts extracted from the conductor side.
• : Pattern from the side which enables seeing.
2-2. CIRCUIT BOARDS LOCATION
POWER SWITCH board
CONTROL board
LED board
POWER board
TRANSFOMER boar
THIS NOTE IS COMMON FOR PRINTED WIRING
SA-VE155/WMS155/SS-MS155
33
Page 4
SA-VE155/WMS155/SS-MS155
2-3. PRINTED WIRING BOARDS (SA-WMS155) • Refer to page 3 for Circuit Boards Location. : Uses unleaded solder.
1
234567891011 12 13 14
A
B
C
D
E
F
G
H
LED BOARD
1
RED
D301
1-862-218- 11
D301
(POWER)
AC IN
I
WHT
3
BC301
TRANSFORMER BOARD
CN802
1
2
T801
CN801
31
BLU
21
C813
BRN
CN803
F801
1-862-216- 11
POWER BOARD
C614
J13
E MODEL
R615
TH601
C601
R601
C602
R603
C608
R604
J12
1
2
J11
10
14
C606
C809
J10
J7
15
J8
J7
C802
D801
IC601
J21
E MODEL
J24
BC601
RED
1
R620
Q604
5
C612
C603
C611
J19
J8
13
J20
R602
R613
C610
C607
J17
J14
C815
C814 RED
BC801
R614
R616
Q605
R618 R804
CN601
2
1
RLY601
R605
C801
J16
J15
R607
D603
Q602
Q603
C804
C808
D803 D802
C806
Q802
Q606
R802
J22
R619
WHT
R301
J26
J25
J23
R608
1
2
CN301
C803
C807
C805
Q801
R803
R801
Q601
C613
C604
C605
R609
D601
R610
1-862-215- 11
D602
RED
BLK
SP1
SPEAKER
4Ω
POWER SWITCH BOARD
C810
BLU
BRN
CONTROL BOARD
VR501
LEVEL
R511
C517
J2
J501
LINE
IN
J501
1
2
C516
R506
R507
R501
C518
IC502
8
5
C507
R508
C509
C501
J6
1
4
C506
R502
S801BC802
R510
C510
R512
R505
IC501
851
R503
C508
1-862-217- 11
CN501
4
1
C513
J5
R509
C514
J3
J4
C504
R504
C503
C505
4
C512
C502
1-862-214- 11
S801
POWER
WHT
BLK
WHT
RED
C511
J1
J
SA-VE155/WMS155/SS-MS155
WHT
WHT
RED
RED
WHT
WHT
• Semiconductor Location
Ref. No. Location Ref. No. Location Ref. No. Location
D301 B-2
D601 I-9
D602 I-9
D603 J-8
44
D801 I-7
D802 D-9
D803 D-8
IC501 H-12
IC502 G-12
IC601 F-6
Q601 G-9
Q602 D-8
Q603 D-8
Ref. No. Location
Q604 D-7
Q605 E-8
Q606 E-8
Q801 E-9
Q802 E-8
Page 5
2-4. SCHEMATIC DIAGRAM (SA-WMS155) • Refer to page 6 for IC Block Diagram.
SA-VE155/WMS155/SS-MS155
SW801
BC802 CN803
C810
J501
C501
CN802
R504
C502
R501
C813
R503
C503
R502 R505
F801
IC501(1/2)
T801
CN801
C506
BC801
C507
R506 R507
C508
C815
C814
D603
C512
C809
IC501(2/2)
C509
C504C505 C513C514
C511
D801
C801
C802
C510
R509
R508 R511
C516 C517
R510
IC502(1/2)
R801
R803
D802
D803
R804
R802
Q801
C805
C806
Q802
R512
C807
C808
IC502(2/2)
C803
C804
C614
C518
C611
C604
CN501
BC601
C601
VR501
R601
C603
C610
C605
R605
R602
C607
R604
C602
R603
R606
IC B/D
IC601
C608
C606
D602
R609
R610
SA-VE155/WMS155/SS-MS155
D301
BC301
R301
CN301
R607
D601
R608
C613
Q601
R619
R613
Q604
R614
Q603
R620
C612
Q602
TH601
55
R615
R616
Q605
R618
RLY601
CN601
SP1
Q606
Page 6
SA-VE155/WMS155/SS-MS155
2-5. IC BLOCK DIAGRAM
IC601 TDA7296 (POWER Board)
BIPOLAR
TRANSCONDACTANCE
INPUT STAGE
MOS GAIN &
LEVEL SHIFTING
STAGE
BOOST-
STRAP
1 7 13 14 158 92 3 4 5 11 12106
+IN
SUR
NC
-IN
STBY-GND
+VS(SIG)
BOOTSTR
STANDBY/
MUTE
STBY
-VS(SIG)
SHUTDOWN
MOS
OUTPUT
STAGE
MUTE
THERMAL
PROTECTION
NC
SHORT
CIRCUIT
NC
OUT
-VS(POW)
+VS(POW)
SA-VE155/WMS155/SS-MS155
66
Page 7
NOTE:
• The mechanical parts with no reference
number in the exploded views are not supplied.
• Items marked “*” are not stocked since
they are seldom required for routine service.
Some delay should be anticipated
when ordering these items.
• -XX and -X mean standardized parts, so
they may have some difference from the
original one.
SECTION 3
EXPLODED VIEWS
• Color Indication of Appearance Parts
Example :
KNOB, BALANCE (WHITE) ... (RED)
RR
Parts Color Cabinet’s Color
• Accessories are given in the last of this
parts list.
SA-VE155/WMS155/SS-MS155
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
SA-WMS155
11
2
8
13
not supplied
(LED board)
1
6
7
not supplied
11
13
9
3
not supplied
F801
6
7
not supplied
not supplied
(POWER SWITCH board)
4
14
T801
not supplied
(TRANSFORMER board)
supplied with VR501
7
12
not supplied
SS-MS155
10
5
12
7
7
not supplied
(CONTROL board)
11
11
11
not supplied
(E model)
not supplied
15
not supplied
7
Ref. No. Part No. Description Remark
1 X-4956-464-1 GRILLE ASSY
2 A-1067-893-A POWER BOARD, COMPLETE (SA-WMS155:E)
2 A-4752-980-A POWER BOARD, COMPLETE
0 31-696-570-11 CORD, POWER (SA-WMS155:UK)
0 31-769-744-52 CORD, POWER (SA-WMS155:AEP,E)
44-973-938-01 KNOB (A), PUSH
52-021-063-01 KNOB (VOL)
64-255-554-01 FOOT
74-238-407-12 SCREW (1) (4X20), +BV TAPPING
87-682-950-09 SCREW +PSW 3X12
* 93-703-244-21 BUSHING (2104), CORD
SP1
7
(SA-WMS155:AEP,UK)
Ref. No. Part No. Description Remark
10 7-685-660-79 SCREW +BVTP 4X10 TYPE2 IT-3
11 7-685-647-79 SCREW +BVTP 3X10 TYPE2 IT-3
12 7-685-646-79 SCREW +BVTP 3X8 TYPE2 IT-3
13 7-682-903-11 SCREW +PWH 3X6
14 7-682-147-01 SCREW +P 3X6
15 A-1067-011-A SYSTEM (MS) ASSY (SS-MS155:E)
15 A-4715-730-A SYSTEM (MS) ASSY (SS-MS155:AEP,UK)
0 F801 1-532-389-51 FUSE (T0.5AL/250V)
SP1 1-825-843-11 SPEAKER (16cm) (WOOFER)
0 T801 1-443-372-11 TRANSFORMER, POWER
7
Page 8
SA-VE155/WMS155/SS-MS155
SECTION 4
CONTROL
LED
ELECTRICAL PARTS LIST
POWER
NOTE:
• Due to standardization, replacements in
the parts list may be different from the
parts specified in the diagrams or the
components used on the set.
• -XX and -X mean standardized parts, so
they may have some difference from the
original one.
• RESISTORS
All resistors are in ohms.
METAL:Metal-film resistor.
METAL OXIDE: Metal oxide-film resistor.
F:nonflammable
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
CONTROL BOARD
***************
< CAPACITOR >
C501 1-107-473-11 CERAMIC 220PF 5% 50V
C502 1-126-964-11 ELECT 10uF 20% 50V
C503 1-107-473-11 CERAMIC 220PF 5% 50V
C504 1-101-004-00 CERAMIC 0.01uF 50V
C505 1-101-004-00 CERAMIC 0.01uF 50V
C506 1-126-964-11 ELECT 10uF 20% 50V
C507 1-131-695-11 FILM 0.18uF 5% 50V
C508 1-131-691-11 FILM 0.082uF 5% 50V
C509 1-131-695-11 FILM 0.18uF 5% 50V
C510 1-136-165-00 FILM 0.1uF 5% 50V
C511 1-126-964-11 ELECT 10uF 20% 50V
C512 1-126-964-11 ELECT 10uF 20% 50V
C513 1-101-004-00 CERAMIC 0.01uF 50V
C514 1-101-004-00 CERAMIC 0.01uF 50V
C516 1-136-165-00 FILM 0.1uF 5% 50V
• Items marked “*” are not stocked since
they are seldom required for routine service.
Some delay should be anticipated
when ordering these items.
• SEMICONDUCTORS
In each case, u : µ, for example:
uA.. : µA.. µPA.. : µPA..
uPB.. : µPB.. uPC.. : µPC.. uPD.. : µPD..
• CAPACITORS
uF : µF
• COILS
uH : µH
R512 1-249-438-11 CARBON 56K 5% 1/4W
VR501 1-227-666-11 RES, VAR 5K (LEVEL)
*************************************************************
D301 8-719-080-25 LED SEL6414LF62 (POWER)
*************************************************************
A-1067-893-A POWER BOARD, COMPLETE (E)
A-4752-980-A POWER BOARD, COMPLETE (AEP,UK)
BC801 1-564-506-11 PLUG, CONNECTOR 3P
The components identified by
mark 0 or dotted line with mark.
0 are critical for safety.
Replace only with part number
specified.
When indicating parts by reference
number, please include the board.
< VARIABLE RESISTOR >
LED BOARD
**********
< DIODE >
***********************
< CONNECTOR >
C517 1-136-165-00 FILM 0.1uF 5% 50V
C518 1-126-964-11 ELECT 10uF 20% 50V
< CONNECTOR >
CN501 1-564-507-11 PLUG, CONNECTOR 4P
< IC >
IC501 8-759-634-51 IC M5218AP
IC502 8-759-634-51 IC M5218AP
< JACK >
J501 1-774-785-11 JACK, PIN 1P (LINE IN)
< RESISTOR >
R501 1-249-433-11 CARBON 22K 5% 1/4W
R502 1-249-441-11 CARBON 100K 5% 1/4W
R503 1-249-437-11 CARBON 47K 5% 1/4W
R504 1-249-439-11 CARBON 68K 5% 1/4W
R505 1-249-441-11 CARBON 100K 5% 1/4W
R506 1-249-427-11 CARBON 6.8K 5% 1/4W
R507 1-249-427-11 CARBON 6.8K 5% 1/4W
R508 1-249-434-11 CARBON 27K 5% 1/4W
R509 1-249-438-11 CARBON 56K 5% 1/4W
R511 1-249-434-11 CARBON 27K 5% 1/4W
< CAPACITOR >
C601 1-126-960-11 ELECT 1uF 20% 50V
C602 1-131-695-11 FILM 0.18uF 5% 50V
C603 1-104-658-11 ELECT 100uF 20% 10V
C604 1-126-964-11 ELECT 10uF 20% 50V
C605 1-126-964-11 ELECT 10uF 20% 50V
C606 1-126-965-11 ELECT 22uF 20% 50V
C607 1-131-688-31 FILM 0.047uF 5% 50V
C608 1-102-973-00 CERAMIC 100PF 5% 50V
C610 1-126-964-11 ELECT 10uF 20% 50V
C611 1-126-964-11 ELECT 10uF 20% 50V
C612 1-126-924-11 ELECT 330uF 20% 10V
C613 1-126-965-11 ELECT 22uF 20% 50V
C614 1-101-004-00 CERAMIC 0.01uF 50V
C801 1-126-955-11 ELECT 4700uF 20% 35V
C802 1-126-955-11 ELECT 4700uF 20% 35V
C803 1-101-004-00 CERAMIC 0.01uF 50V
C804 1-101-004-00 CERAMIC 0.01uF 50V
C805 1-126-964-11 ELECT 10uF 20% 50V
C806 1-126-964-11 ELECT 10uF 20% 50V
C807 1-126-964-11 ELECT 10uF 20% 50V
C808 1-126-964-11 ELECT 10uF 20% 50V
C809 1-101-005-00 CERAMIC 0.022uF 50V
C814 1-131-688-31 FILM 0.047uF 5% 50V
C815 1-131-688-31 FILM 0.047uF 5% 50V
8
Page 9
SA-VE155/WMS155/SS-MS155
POWER SWITCH TRANSFORMERPOWER
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
< CONNECTOR >
CN301 1-564-505-11 PLUG, CONNECTOR 2P
CN601 1-564-320-00 PIN, CONNECTOR (3.96mm PITCH) 2P
POWER SWITCH BOARD
********************
< CAPACITOR >
< DIODE >
D601 8-719-991-33 DIODE 1SS133T-77
D602 8-719-991-33 DIODE 1SS133T-77
D603 8-719-991-33 DIODE 1SS133T-77
D801 8-719-312-47 DIODE RBA-406B
D802 8-719-921-88 DIODE MTZJ-13B
D803 8-719-921-88 DIODE MTZJ-13B
< IC >
IC601 8-759-584-38 IC TDA7296
< TRANSISTOR >
Q601 8-729-016-42 TRANSISTOR KTC3199GR-TP
Q602 8-729-016-42 TRANSISTOR KTC3199GR-TP (E)
Q603 8-729-016-42 TRANSISTOR KTC3199GR-TP
Q604 8-729-016-42 TRANSISTOR KTC3199GR-TP
Q605 8-729-016-42 TRANSISTOR KTC3199GR-TP
Q606 8-729-016-42 TRANSISTOR KTC3199GR-TP
Q801 8-729-036-89 TRANSISTOR KTC3198GR-AT
Q802 8-729-037-02 TRANSISTOR KTA1266Y-AT
< RESISTOR >
R301 1-249-417-11 CARBON 1K 5% 1/4W
R601 1-249-421-11 CARBON 2.2K 5% 1/4W
R602 1-249-433-11 CARBON 22K 5% 1/4W
R603 1-249-433-11 CARBON 22K 5% 1/4W
R604 1-247-807-31 CARBON 100 5% 1/4W
0 C810 1-135-450-51 FILM 0.01uF 10% 275V
< SWITCH >
0 SW801 1-786-749-11 SWITCH, POWER (POWER)
*************************************************************
TRANSFORMER BOARD
********************
1-533-313-11 HOLDER, FUSE
< CAPACITOR >
0 C813 1-135-450-51 FILM 0.01uF 10% 275V
< CONNECTOR >
CN801 1-564-506-11 PLUG, CONNECTOR 3P
CN802 1-564-321-00 PIN, CONNECTOR (3.96mm PITCH) 2P
* CN803 1-580-230-11 PIN, CONNECTOR (PC BOARD) 2P
< FUSE >
0 F801 1-532-389-51 FUSE (T0.5AL/250V)
< TRANSFORMER >
0 T801 1-443-372-11 TRANSFORMER, POWER
*************************************************************
MISCELLANEOUS
***************
R605 1-247-727-11 CARBON 10 5% 1/2W
R606 1-249-433-11 CARBON 22K 5% 1/4W
R607 1-247-761-11 CARBON 5.6K 5% 1/2W
R608 1-249-433-11 CARBON 22K 5% 1/4W
R609 1-249-435-11 CARBON 33K 5% 1/4W
R610 1-249-429-11 CARBON 10K 5% 1/4W
R613 1-249-430-11 CARBON 12K 5% 1/4W
R614 1-249-426-11 CARBON 5.6K 5% 1/4W
R615 1-249-429-11 CARBON 10K 5% 1/4W (E)
R616 1-249-429-11 CARBON 10K 5% 1/4W
R618 1-249-429-11 CARBON 10K 5% 1/4W
R619 1-249-441-11 CARBON 100K 5% 1/4W
R620 1-247-887-00 CARBON 220K 5% 1/4W
R801 1-260-292-11 CARBON 1 5% 1/2W F
R802 1-260-292-11 CARBON 1 5% 1/2W F
R803 1-247-843-11 CARBON 3.3K 5% 1/4W
R804 1-247-843-11 CARBON 3.3K 5% 1/4W
< RELAY >
RLY601 1-755-170-11 RELAY (12V)
< THERMISTOR (POSITIVE) >
TH601 1-809-789-71 THERMISTOR, POSITIVE (E)
*************************************************************
0 3 1-696-570-11 CORD, POWER (UK)
0 3 1-769-744-52 CORD, POWER (AEP,E)
SP1 1-825-843-11 SPEAKER (16cm) (WOOFER)
*************************************************************
ACCESSORIES
************
0 1-569-008-32 ADAPTOR, CONVERSION (E)
2-021-397-11 MANUAL, INSTRUCTION (ENGLISH,FRENCH,
SPANISH,PORTUGUESE)
2-021-397-21 MANUAL, INSTRUCTION (GERMAN,ITALIAN,
DUTCH,SWEDISH) (AEP)
2-021-397-31 MANUAL, INSTRUCTION (DANISH,FINNISH,
POLISH,RUSSIAN) (AEP)
2-021-397-41 MANUAL, INSTRUCTION
(SIMPLIFIED CHINESE,
TRADITIONAL CHINESE) (E)
The components identified by
mark 0 or dotted line with mark.
0 are critical for safety.
Replace only with part number
specified.
9
Page 10
SA-VE155/WMS155/SS-MS155
REVISION HISTORY
Clicking the version allows you to jump to the revised page.
Also, clicking the version at the upper on the revised page allows you to jump to the next revised page.
Ver. Date Description of Revision
1.0 2004.05 New
10
Loading...