Sony SRX-S105, SRX-S110, SRX-R110CE, SRX-R105CE User Manual

Page 1
SXRD 4K Ultra High Resolution Projectors
SRX-R110CE / SRX-R105CE SRX-S110 / SRX-S105
www.sonybiz.net/4k
Page 2
Amazing 4K resolution images for large-venue applications
2
Page 3
Sony is proud to introduce a series of SXRD™ultra high-resolution projectors, which offer supreme picture quality and reality for applications that require highly sophisticated visuals. This state-of-the-art Sony projector series, comprising the SRX-S110, SRX-S105, SRX-R110CE, and SRX-R105CE models, provides a new solution for applications such as command & control, simulations, computer visualisations, planetarium and museum exhibitions, and much more.
Each model is equipped with three Silicon X-tal Reflective Display (SXRD) imaging devices and delivers an amazing resolution of 4096 x 2160 pixels (H x V) – more than four times the resolution of HD (1920 x 1080, 16:9 wide screen format). The ultra high resolution capability enables a single HD or 2K image to be internally up-converted by the projector and displayed as a 4K image for a stunning image. Aternatively the projector's multiple screen mode allows full HD images to be displayed simultaneously in four quadrants or in a twin "side by side" display.
The projectors also offer a contrast ratio of more than 1800:1. In addition, the SRX-S110 and SRX-R110CE models provide a high brightness of 10,000 ANSI lumens*, while the SRX-S105 and SRX-R105CE models offer a brightness of 5,000 ANSI lumens.
The use of twin Xenon lamps combined with multiple gamma curves of 1.8, 2.2, and 2.6 means they offer pure, high-quality colour tonal reproduction.
The SRX-S110 and SRX-S105 models – each with one fixed DVI input module – have a 1080/60P display capability available only with these units, making them ideal for high-end computer graphic­based projection applications. On the other hand, the SRX-R110CE and SRX-R105CE models – supplied with one removable analogue input board– are more suited to video-based projection applications.
Sony SXRD 4K projectors are the ultimate tool for image display in a variety of critical applications from high resolution visualisation systems to large-venue projection.
*
ANSI lumens is a measuring method of the American National Standards Institute IT 7.228. Since there is no uniform method of measuring brightness, specifications will vary among manufacturers.
3
Page 4
High 1800:1 contrast ratio
The SRX-Series projectors offer a high contrast ratio of more than 1800:1* through the use of Sony’s unique SXRD device. The SXRD imaging device itself achieves a contrast ratio of over 4000:1. This stunning picture quality makes the projectors ideal for applications in which dynamic range is essential.
The high contrast ratio has been achieved through two key technolo­gies – the exclusive ‘Vertically Aligned Liquid Crystal’ system and an extremely thin liquid crystal cell gap.
*
The contrast ratio is measured from a screen offering a gain of 1.0.
Vertically Aligned Liquid Crystal system
In every type of projector system, displaying absolute black is a major issue in order to achieve a high contrast ratio. In other words, the con­trast ratio of a projector depends on how effectively the light from the source can be blocked so it does not leak through the imager.
All Liquid Crystal Display (LCD) devices control the amount of light to be projected by applying an electric field to the liquid crystal gap. In typical LCD devices, black is produced when an electric field is applied across the liquid crystal cell gap. However molecules near the surface of the glass substrate may not be accurately controlled due to the influence of the alignment film. This is not an issue for bright images. However, when displaying dark images, light may tend to leak from the LCD device, since the molecules near the surface are less accurately controlled. This results in a creamy black instead of a deep black.
The SXRD device does not exhibit these characteristics. This is because the Vertically Aligned Liquid Crystal system displays black when the electric field is not applied. And because all molecules are in the correct alignment, the polarised light alignment is also optimised. The direct result is a far deeper black level, leading to a high contrast ratio.
State-of-the-art technology for fantastic picture quality
4K
(4096 H x 2160 V pixels at 1.896:1 aspect ratio)
2K
(2048 H x 1080 V)
full HDTV
(1920 x 1080,
16:9 wide screen format)
State-of-the-art technology
4
Silicon X-tal Reflective Display (SXRD) imaging device
The SXRD device used by the SRX-Series projectors is a 1.55-inch* Liquid Crystal on Silicon based imager developed by Sony using cutting-edge manufacturing technology. High-quality, accurate visuals are created using this brilliant imaging device.
*
Measured diagonally.
4K resolution
Sony SXRD display devices deliver the exceptionally high resolution of 4K (4096 H x 2160 V pixels at 1.896:1 aspect ratio), more than four times as many pixels as full HDTV (1920 x 1080, 16:9 wide screen format).
The SXRD device helps to achieve this resolution by incorporating nearly 8.85 million pixels per imager at a narrow pitch of 8.5 micro­metres. These high-density pixels, which are one quarter the size of pixels projected using typical 2K resolution projection systems (2.2 million pixels), provide an amazing picture. Even in multi-screen mode, full HD and 2K resolution per quadrant is possible. The resolution available from the Sony SRX-Series projectors enables a new level of visual projection.
Shown: ApolloWall-Pro from HoloVis (www.holovis.com)
Page 5
Short response time
The thin cell gap structure in SXRD devices also contributes to an ultra-fast response time of 5 milliseconds. The SXRD device reacts promptly to an instantaneous change of picture content, enabling them to display a smooth motion.
Consequently, the SRX-Series projectors virtually eliminate motion blur. This is a particularly significant benefit for visuals that include fast-moving objects.
Reliable imaging device
The SRX-Series projectors use high-power, bright lamps. Consequently, special attention has been paid to the reliability of the SXRD device. The inorganic materials utilised for the alignment layer of the SXRD device are resistant to deterioration or deformities that could occur due to the intense heat and light generated by the powerful twin lamp system.
Thin liquid crystal cell gap
Another important contributing factor in the high contrast of the SXRD projectors is the SXRD device’s ultra thin cell gap of less than 2 micrometres. With conventional Vertically Aligned Liquid Crystal sys­tems, a thin cell gap could not be achieved. Sony has overcome this difficulty through the use of innovative planarisation technology in the silicon backplane structure and an advanced silicon wafer-based assembly process.
The SXRD device also adopts a structure that does not use “spacers”. These are columns found in conventional reflective liquid crystal devices to maintain a constant gap between the liquid cell floor and the top of the device. Spacers tend to both scatter and reflect light, which can impair high contrast pictures. In the spacerless SXRD device, these artifacts are no longer seen.
SXRD Cross-Section view
Glass Substrate
Thin Cell Gap (2.0 µm) Space-less
• Short reponse time < 5 msec
• High Device Contrast ratio 4000:1
Narrow Inter-Pixel Spacing (0.35 µm)
• High fill factor 92 %
• High reflectivity
Inorganic Alignment Layer
• High reliability
Aluminium Pad
Light
Silicon Backplane
Vertically Aligned
Liquid Crystal
Hight-Density Pixel Pitch 8.5 µm
• 4K x Full HD
(4096 H x 2160 V pixels)
State-of-the-art technology
5
High-speed Image Display
Page 6
Highly pure, superb
colour tonal reproduction
Colour Space Conversion (CSC) function
The SRX-Series projectors feature a CSC function to help users easily adjust the projector’s colour space to that defined by either the ITU*-R BT.709-3 standards for digital HDTV studio colour space, or the new DCDM colour space.
The latter is significantly wider than ITU 709 and takes advantage of the spectrum emitted by the Xenon lamp. The target colour gamut parameters satisfying the ITU-R BT. 709-3 standard or DCDM specification are automatically calculated from settings on the supplied SRX Controller software, and then applied to the projector. The internal test generator simplifies adjustment and lets the operator align the projector in minutes. White point and colour primary points can be aligned to either of these standards or to the customer’s appli­cation needs.
*
International Telecommunication Union
12-bit LCD driver
The SRX-Series projectors use a 12-bit imager driver to reproduce extremely natural-looking images. This eliminates quantising and edge errors that take away from the real resolution that these projectors can achieve.
Gamma curve selection
The SRX-Series projectors provide three preset gamma curve values. Users can select an optimum value from 1.8, 2.2, and 2.6 according to the desired grey scale.
Xenon lamp provides highly bright and pure light
The SRX-S110 and SRX-R110CE models provide high brightness of 10,000 ANSI lumens* from two 2kW Xenon lamps, while the SRX-S105 and SRX-R105CE models offer brightness of 5,000 ANSI lumens from two 1 kW Xenon lamps.
The Xenon lamps in SRX-Series projectors achieve a wide colour range by dispersing a very flat and wide light spectrum.
*
Measured under conditions with the lamp power at 100% in dual-lamp mode.
Highly pure, superb colour tonal reproduction
CIE chart
Film
Xenon
TV
6
Wide Colour Range
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.70.60.50.40.30.20.10.0 0.8
Page 7
Operational
versatility
Zoom/Focus memory function
The SRX-Series projectors are equipped with Zoom and Focus Memory functions that make it easy to switch the projection between two types of aspect ratios. When used with the optional LKRL-Z117, LKRL-Z119 and LKRL-Z122 Zoom Lenses, any seven zoom and focus positions can be memorised and instantly recalled via the SRX Controller software. This allows full screen display regardless of the aspect ratio. An electronic vertical alignment feature is included in the same memory to compensate for vertical changes in the image should the projector be mounted at a down angle.
Multiple screen capability
The SRX-Series projectors provide single-mode, dual-mode and quad-mode display. In quad mode, four quadrants of full 2K images (2048 x 1080 pixels) can be projected simultaneously. The projector can additionally internally up-convert a single HD or 2K input. To obtain a 4K image of 4096 x 2160 pixels, 4 inputs of full 2K images are input and stitched together internally in the projector.
Dual-lamp system with selectable lamp modes
The SRX-Series projectors have a unique lamp system that uses two lamps for reliable, flexible and efficient use of light sources. With this system, users can operate the projector using both lamps for full brightness or can select single lamp operations.
The dual-lamp mode provides maximum lamp power, and at the same time enables virtually fail-safe operation; if one bulb burns out the other continues to project images.
In the single-lamp mode, users can select either of the two lamps manually, or the projector can automatically select a lamp based on each lamp’s operating time. Another automatic mode is provided to make the lamps operate alternately at user-defined intervals selectable from four hours to twelve hours (in increments of one hour). This feature is useful for the application where “24/7” operation is required, but lamp life needs to be max­imised.
The lamp power can be set between 100 % and 51 %, in eight steps. This function, combined with the selectable lamp modes, contributes to achieving longer lamp life.
Variety of lenses
Four optional zoom lenses and a short throw prime lens are available for the SRX-Series projectors. They are designed to project images of extreme resolution and contrast with minimal chromatic aberration from 1,829 mm to 15,497 mm in screen width. The short throw lens works in special applications, such as rear projection, where minimal space behind the screen is desired.
Available lenses
LKRL-90: 0.9x fixed focal length projection lens LKRL-Z115: 1.5 to 1.9x projection zoom lens LKRL-Z117: 1.73 to 2.41x projection zoom lens LKRL-Z119: 1.81 to 2.94x projection zoom lens LKRL-Z122: 2.31 to 3.92x projection zoom lens LKRL-Z140: 4.0 to 7.0x projection zoom lens
Operational versatility
Single-mode
Dual-mode
Quad-mode
A
A
B
AB
CD
7
Page 8
• The LKRI-004 DVI interface board accepts DVI-D signals up to
2048 x 1080 and the following table illustrates the range of input signals handled by each projector.
Simple Installation
SRX-Series projectors can be installed easily into almost any envi­ronment. Compared with conventional projectors in the ultra-high res­olution class, they are highly compact and lightweight. Plus, their power requirements are also reasonable – due to the use of single­phase power, which allows for remarkably low power consumption and simpler installation.
To aid effective cooling, an optional exhaust duct adaptor is available, which allows the projectors to be easily connected to a common 8-inch type duct system.
Resolution SRX-S110/S105 SRX-R110CE/R105CE Remarks
1 1024 x 768 at 60 Hz (XGA) YES YES VESA
2 1280 x 960 at 60 Hz (SXGA) YES YES VESA
3 1280 x 1024 at 60 Hz (SXGA) YES YES VESA
4 1400 x 1050 at 60 Hz (SXGA+) YES YES VESA
5 1600 x 1200 at 60 Hz (UXGA) YES YES VESA
6 2048 x 1080 at 60 Hz YES NO
7 1920 x 1080 at 24 Hz YES YES
8 2048 x 1080 at 24 Hz YES YES
9
1920 x 1200 at 59.95 Hz Reduced Blanking (WUXGA)
YES NO VESA
10 1920 x 1080 at 60 Hz YES NO EIA/CEA-861B
11 2048 x 1080 at 48 Hz YES YES
Input signal flexibility
To increase the configuration flexibility of the SRX-Series projectors, slots are available to accommodate different optional boards that connect to various types of signal format.
The SRX-S110 and SRX-S105 models are equipped with a DVI signal input as standard, which provides the 1080/60P input capability available only with these units.
In addition to the standard DVI input, three slots are available for the installation of other optional input modules. Meanwhile, the SRX-R110CE and SRX-R105CE models have four available slots for even more flexible input configurations.
The SRX-R105CE and SRX-R110CE are supplied with one removable LKRI-001 input board and the four option board slots can accomodate any combination of input boards. Users can select the screen mode from single, dual, and quad mode, and assign the appropriate signal board to each quadrant.
• The LKRI-001 Analogue input board has 5 BNC connectors that
accept 0.7 volt analogue signal levels as RGBS, RGB sync on G, RGBHV or YUV formats.
• The LKRI-002 HD-SDI (4:2:2) input board accepts both SMPTE
259M SD digital 525/625 line video and SMPTE 292M 1080 4:2:2 Y
-Pb-
Pr serial picture data. Switching is automatic by detection of
the input signal frequency.
• The LKRI-003 Dual-link HD-SDI input board accepts any of the
following signals: SMPTE 372M dual-link HD-SDI (4:4:4), SMPTE 292M HD-SDI (4:2:2), dual-link DC-SDI (RGB 4:4:4), DC-SDI (YPbPr 4:2:2), or 12-bit (X’Y’Z’ 4:4:4) signals. With four LKRI-003 boards, the SRX-R110CE or SRX-R105CE can project 4096 x 2160 4K images.
LKRI-002
HD-SDI (4:2:2) Input Board
LKRI-003
Dual-link HD-SDI Input Board
LKRI-004
DVI Interface Board
Option slots
LKRI-001
Analogue Input Board (Supplied with SRX-R105CE/R110CE)
Operational versatility
8
Page 9
Simple remote controller unit
Each SRX-Series projector is supplied with a remote con­troller unit that can perform various simple functions such as turning the lamp power on/off, adjusting the zoom/focus, and controlling the lens shift.
Easy setup on a PC using supplied software
The SRX-Series projectors come equipped with the SRX Controller software that allows easy setup and adjustments via its intuitive GUIs on a PC*. These projectors can be controlled through either Ethernet or RS-232C interfaces, and multiple projectors can be controlled from a single PC**. A comprehensive range of setup parameters including input configurations, colorimetry controls, installation adjustments and maintenance settings can be controlled via this software.
*
System requirements for the setup software OS: Microsoft Windows
®
XP Professional.
PC is not supplied.
**
When using an Ethernet connection.
Easy maintenance
Special consideration for maintenance issues was given in the development of the SRX-Series projectors. The supplied setup software is another convenient tool for maintenance. This allows oper­ators to easily verify the lamps’ operating time. Automatic email alerts from the projector provide operators with maintenance reminders as well as error messages.
Installation settings
Colorimetry settings
Maintenance settings
SRX-Series
Projector
SRX-Series
Projector
SRX-Series
Projector
SRX-Series
Projector
PC
PC
Ethernet
RS-232C
Operational versatility
9
Large Venue Projection
Page 10
LKRX-105 1kW Xenon lamp
bulb for replacement (for SRX-R105CE and SRX-S105)
LKRA-001 8-inch Exhaust
Duct Adaptor
LKRX-B110 2kW Xenon
lamp house unit (for SRX-R110CE and SRX-S110)
LKRX-B105 1kW Xenon
lamp house unit (for SRX-R105CE and SRX-S105)
LKRX-110 2kW Xenon lamp
bulb for replacement (for SRX-R110CE and SRX-S110)
LKRI-001 Analogue Input
Board (Supplied with SRX-R105CE/R110CE)
LKRI-002 HD-SDI (4:2:2)
Input Board
LKRI-003 Dual-link HD-SDI
Input Board
LKRI-004 DVI Interface Board
LKRL-Z115 Zoom Lens
1.5 to 1.9*x zoom lens
LKRL-90 Fixed Lens
0.9x Fixed Focal Length Projection lens
LKRL-Z122 Zoom Lens
2.31 to 3.92x zoom lens
LKRL-Z140 Zoom Lens
4.0 to 7.0x zoom lens
LKRL-Z117 Zoom Lens
1.73 to 2.41x zoom lens
LKRL-Z119 Zoom Lens
1.81 to 2.94x zoom lens
*
The number denotes the ratio of the projection distance to the screen width.
Accessories
Dimensions
Unit=mm (inches)
1326 (52 1⁄4)
740 (29
1
4)
1116 (44)
754.5 (29
3
4) 167
(6 5⁄8)
357 (14 1⁄8)
395 (15 5⁄8)
498 (19
5
8)
320 (12
5
8)
500 (21
3
4)
10
Page 11
No
0 3 4 5 23 24 25 26 32 33 36 37
Signal Number
NO INPUT VIDEO 60 (480 60i) VIDEO 50 (575 50i) HDTV (1080 60i) 1024 x 768 VESA60 1024 x 768 VESA70 1024 x 768 VESA75 1024 x 768 VESA85 1280 x 960 VESA60 1280 x 960 VESA75 1280 x 1024 VESA60 1280 x 1024 VESA75
fH
0
15.73 kHz
15.63 kHz
33.75 kHz
48.36 kHz
56.48 kHz
60.02 kHz
68.68 kHz
60.00 kHz
75.00 kHz
63.97 kHz
79.98 kHz
fV
0
59.94 kHz
50.00 kHz
60.00 kHz
60.00 kHz
70.07 kHz
75.03 kHz
85.00 kHz
60.00 kHz
75.00 kHz
60.01 kHz
75.03 kHz
Aspect
4:3 4:3 16:9 4:3 4:3 4:3 4:3 4:3 4:3 5:4 5:4
Horizontal Sampling
1280 1280 1920 1024 1024 1024 1024 1280 1280 1280 1280
Vertical Sampling
480 570 1080 768 768 768 768 960 960 1024 1024
No
38 39 45 47 48 49 (75) (76) (77)
Signal Name
1280 x 1024 VESA85 1600 x 1200 VESA60 1080 50i 720 60P 720 50P 1080 48I (24PsF) 1080 60i 1080 25PsF 1080 30PsF
fH
91.15 kHz
75.00 kHz
31.25 kHz
45.00 kHz
37.50 kHz
27.00 kHz
33.75 kHz
31.25 kHz
33.75 kHz
fV
85.02 kHz
60.00 kHz
50.00 kHz
60.00 kHz
50.00 kHz
48.00 kHz
60.00 kHz
50.00 kHz
60.00 kHz
Aspect
5:4 4:3 16:9 16:9 16:9 16:9 16:9 16:9 16:9
Horizontal Sampling
1280 1600 1920 1280 1280 1920 1920 1920 1920
Vertical Sampling
1024 1200 1080 720 720 1080 1080 1080 1080
Note:
*
When a signal other than the preset signals shown above is fed into this projector, the images may not be projected properly.
Specifications
Preset Data of Input Signals
SXRD Device Main Specifications
Display device
SXRD (Silicon X-tal Reflective Display)
Size
1.55-inch across Diagonal
Resolution
4096(H) X 2160(V) Pixels
Reflectivity
72%
Contrast (as device)
More than 4000 : 1
Pixel pitch
8.5 µm
Width (between pixels)
0.35 µm
Response speed
5 msec (tr + tf)
Liquid crystal mode
Vertical Aligned Mode
Alignment layer
Inorganic Thin Film
Backplane process
0.35 µm MOS Process
Liquid crystal cell gap
Less than 2 µm
Optical
Projection system
3-SXRD panel, prism colour integrated system
Imaging device
SXRD, 1.55-inch (diagonal), 4096(H) x 2160(V) pixels on each chip
Lamp
2 kW Xenon lamp x 2 (SRX-R110CE) 1 kW Xenon lamp x 2 (SRX-R105CE)
Screen coverage
Approx. 4.5 m to 15.5 m (viewable area, measured horizontally)
Light output
10,000 ANSI lumens ±10 % (SRX-R110CE/S110)* 5,000 ANSI lumens ±10 % (SRX-R105CE/S105)
General
White reference
Xenon white reference
White reference
Y: 0.3510 / X: 0.3140
Contrast
more than 1800:1
Resolution
600 TV lines (SDI input/SMPTE-259M) 1920 x 1080 pixels (HD-SDI input, SMPTE-292M) 4096 x 2160 pixels (RGB)
Signal specifications
SRX-S110 / SRX-S105
Video: Component (Y • Cb • Cr), HD (G • B • R/Y • Pb • Pr) Computer: XGA, SXGA, UXGA DVI-D: XGA, Quad-VGA, SXGA, UXGA, WUXGA, 1920 x 1080, 2048 x 1080
SRX-R110CE / SRX-R105CE
Video: Component (Y • Cb • Cr), HD (G • B • R/Y • Pb • Pr) Computer: XGA, SXGA, UXGA
Power requirements
AC 200 to 240 V, 50/60 Hz (SRX-R110CE/S110) AC 100 to 240 V, 50/60 Hz (SRX-R105CE/S105)
Operating temperature
+5 ºC to +35 ºC (+41 ºF to +90 ºF)
Storage temperature
-20 ºC to +60 ºC (-4 ºF to +140 ºF)
Operating humidity
35 % to 85 % (without condensation)
Storage humidity
10 % to 90 %
Dimensions (W x H x D)
Approx. 740 x 500 x 1330mm (29
4
5 x 19 4⁄5 x 52 3⁄5 inchs)
Mass
Approx. 110 kg (242 lb 8oz)
Input/Output
Input A
DVI-D interface board (SRX-S110/SRX-S105) Open for optional signal interface board (SRX-R110/SRX-R 105)
Input B
Open for optional signal interface board
Input C
Open for optional signal interface board
Input D
Open for optional signal interface board
Remote interface
D-sub 9-pin, RS-232C (female) x 1 Ethernet terminal, 10Base-T/100Base-TX x 1
Input Boards
LKRI-001 Analogue input board
BNC x 5, HD/SD analogue video input, RGB/Y • Cb • Cr selectable
Computer signals
R: 0.7 Vp-p ±2 dB positive, 75 G: 0.7 Vp-p ±2 dB positive, 75 B: 0.7 Vp-p ±2 dB positive, 75
Sync
HD Horizontal: TTL level, high impedance, sync positive/negative HD Vertical: TTL level, high impedance, sync positive/negative
Standard definition video (Y • Cb • Cr)
Y; 1.0 Vp-p ±2 dB sync negative, 75 Cb: 0.7 Vp-p ±2 dB positive, 75 Cr: 0.7 Vp-p ±2 dB positive, 75
High definition video (RGB)
R: 0.7 Vp-p ±2 dB positive, 75 G: with sync 1.0 Vp-p ±2 dB, 75 Ω, Tri-level sync: ±0.3 Vp-p / Bi-level sync: 0.3 Vp-p B: 0.7 Vp-p ±2 dB positive, 75
High definition video (Y • Pb • Pr)
Y: 1.0 Vp-p ±2 dB, 75 Ω, Tri-level sync: ±0.3 Vp-p / Bi-level sync: 0.3 Vp-p Pb: ±0.35 Vp-p ±2 dB, positive 75 Pr: ±0.35 Vp-p ±2 dB, positive 75
LKRI-002 HD-SDI (4:2:2) input board
BNC x 2 (Input x 1,Loop-through out x 1) HD-SDI (SMPTE-292M / ITU-R.BT709 / BTA-S004) SDI (SMPTE-259M / ITU-R.BT601)
LKRI-003 Dual-link HD-SDI input board
BNC x 4 (Input x 2,Loop-through out x 2) HD-SDI (Single-link, HD-SDI/4:2:2,SMPTE­292M):Y • Pb • Pr, DC-SDI (Single-link, DC-SDI/4:2:2):Y • Pb • Pr, Dual-link HD-SDI (Dual-link HD-SDI/4:4:4, SMPTE-372M):RGB, Dual-link DC-SDI (Dual-link DC-SDI/4:4:4):RGB
LKRI-004 DVI Interface Board
SRX-S110/SRX-S105:
1024 x 768 at 60 Hz (XGA), 1280 x 960 at 60 Hz (SXGA), 1280 x1024 at 60 Hz(SXGA), 1400 x 1050 at 60 Hz (SXGA+), 1600 x 1200 at 60 Hz (UXGA), 2048 x 1080 at 60 Hz, 1920 x 1080 at 24 Hz, 2048 x 1080 at 24 Hz, 1920 x 1200 at 59.95 Hz Reduced Blanking (WUXGA) 1920 x 1080 at 60 Hz, 2048 x 1080 at 48 Hz
SRX-R110/SRX-R105:
1024 x 768 at 60 Hz (XGA), 1280 x 960 at 60Hz (SXGA), 1280 x 1024 at 60 Hz (SXGA), 1400 x 1050 at 60 Hz (SXGA+), 1600 x 1200 at 60 Hz (UXGA), 1920 x 1080 at 24 Hz, 2048 x 1080 at 24 Hz
Others
Safety regulations
(UL60950 listed), (cUL60950), (FCC Class A), (IC Class A), (VCCI Class A), (EN60950), (CE Class A), (C-tick), (GB4943), (GB9254), (K60950), (CISPR22), (CISPR24)
Supplied Accessories
Remote controller x 1 CD-ROM x 1 (Remote control application for Windows
®
XP Professional Edition) Dry cell (AA size) x 2 Ethernet Cross Cable (3 m) x 1 Operation instructions x 1 (SRX-S110/SRX-S105) Installation manual x 1 (SRX-R110/SRX-R105)
Optional Accessories
LKRL-90: 0.9x Fixed Focal Length Projection lens LKRL-Z115: 1.5 to 1.9x zoom lens LKRL-Z117: 1.73 to 2.41x zoom lens LKRL-Z119: 1.81 to 2.94x zoom lens LKRL-Z122: 2.31 to 3.92x zoom lens LKRL-Z140: 4.0 to 7.0x zoom lens LKRI-001: Analogue input board LKRI-002: HD-SDI (4:2:2) input board LKRI-003: Dual-link HD-SDI input board LKRI-004: DVI interface board LKRX-105: 1kW Xenon lamp bulb for replacement (for SRX-R105CE) LKRX-B105: 1kW Xenon lamp house unit for replacement (for SRX-R105CE) LKRX-110: 2kW Xenon lamp bulb for replacement (for SRX-R110CE) LKRX-B110: 2kW Xenon lamp house unit for replacement (for SRX-R110CE) LKRA-001: 8-inch Exhaust Duct adaptor
11
Page 12
© 2007 Sony Corporation. All rights reserved. Reproduction in whole or in part without permission is prohibited. Features and specifications are subject to change without notice. All non-metric weights and measurements are approximate. Sony, CineAlta 4K, SXRD, and SXRD logo are trademarks of Sony Corporation. Windows is a registered trademark of Microsoft Corporation. Pentium is a registered trademark of Intel Corporation.
CA SRX-Series/GB- / /2007
Loading...