Sony SNCA-ZP104 Installation Manual

4-412-914-11 (1)

Hybrid Camera Receiver

Installation Manual

Before operating the unit, please read this manual thoroughly and retain it for
future reference.

SNCA-ZX104/ZP104

© 2012 Sony Corporation Printed in China

Owner’s Record

The model and serial numbers are located on the bottom of the unit. Record these
numbers in the spaces provided below.
Refer to these numbers whenever you call upon your Sony dealer regarding this
product.
Model No.

WARNING

To reduce the risk of fire or electric shock, do not
expose this apparatus to rain or moisture.

To avoid electrical shock, do not open the cabinet.
Refer servicing to qualified personnel only.

WARNING

This installation should be made by a qualified service person and should conform to
all local codes.

WARNING

This unit has no power switch.
When installing the unit, incorporate a readily accessible disconnect device in the
fixed wiring, or connect the power plug to an easily accessible socket-outlet near the
unit.
If a fault should occur during operation of the unit, operate the disconnect device to
switch the power supply off, or disconnect the power plug.

WARNING

Using this unit at a voltage other than 120 V may require the use of a different line
cord or attachment plug, or both. To reduce the risk of fire or electric shock, refer
servicing to qualified service personnel.

For the customers in the U.S.A.

This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference
in which case the user will be required to correct the interference at his own expense.

You are cautioned that any changes or modifications not expressly approved in this
manual could void your authority to operate this equipment.

All interface cables used to connect peripherals must be shielded in order to comply
with the limits for a digital device pursuant to Subpart B of Part 15 of FCC Rules.

This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.

For the customers in Canada

This Class A digital apparatus complies with Canadian ICES-003.

For the customers in Europe

The manufacturer of this product is Sony Corporation, 1-7-1 Konan, Minato-ku, Tokyo,
Japan.
The Authorized Representative for EMC and product safety is Sony Deutschland
GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Germany.
For any service or guarantee matters please refer to the addresses given in separate
service or guarantee documents.
This apparatus shall not be used in the residential area.

For the customers in Europe, Australia and New Zealand

WARNING

This is a Class A product. In a domestic environment, this product may cause radio
interference in which case the user may be required to take adequate measures.
In the case that interference should occur, consult your nearest authorized Sony
service facility.

Serial No.

Notes on Use

Before Use

If you find condensation when you open the package, turn on the power after leaving
the unit off for about 60 minutes.

Data and security

Access to the SNCA-ZX104 is protected only by a user name and your set password.



SONY IS NOT RESPONSIBLE, AND ASSUMES ABSOLUTELY NO LIABILITY TO YOU OR



ANYONE ELSE, FOR THE INTERRUPTION, DISCONTINUATION OR CANCELLATION OF
SERVICE(S) RELATED TO THIS RECEIVER. THE SERVICE IS PROVIDED AS-IS, AND SONY
DISCLAIMS AND EXCLUDES ALL WARRANTIES, EXPRESS OR IMPLIED, WITH RESPECT
TO THE SERVICE INCLUDING, BUT NOT LIMITED TO, ANY OR ALL IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR
THAT IT WILL OPERATE ERROR-FREE OR CONTINUOUSLY.
Always verify that the unit is operating properly before use. SONY WILL NOT BE



LIABLE FOR DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED TO,
COMPENSATION OR REIMBURSEMENT ON ACCOUNT OF THE LOSS OF PRESENT OR
PROSPECTIVE PROFITS DUE TO FAILURE OF THIS UNIT, EITHER DURING THE
WARRANTY PERIOD OR AFTER EXPIRATION OF THE WARRANTY, OR FOR ANY OTHER
REASON WHATSOEVER.
If you lose data by using this unit, Sony accepts no responsibility for restoration of



the data.

Operating or storage location

Avoid operating or storing the unit in the following locations.

Extremely hot or cold places (Operating temperature: 0 °C to 45 °C [32 °F to



113 °F])
Exposed to direct sunlight for a long time, or close to heating equipment (e.g., near



heaters)
Close to sources of strong magnetism



Close to sources of powerful electromagnetic radiation, such as radios or TV



transmitters
Locations subject to strong vibration or shock



Ventilation

To prevent heat buildup, do not block air circulation around the unit.

Transportation

Always turn off the power when carrying.



When transporting the unit, repack it as originally packed at the factory or in



materials of equal quality.

Cleaning

Use a soft, dry cloth to clean the external surfaces of the camera. Stubborn stains



can be removed using a soft cloth dampened with a small quantity of detergent
solution, then wipe dry.
Do not use volatile solvents such as alcohol, benzene or thinners as they may



damage the surface finishes.

Please consult the store of purchase or authorized Sony dealer if there were troubles
and anomalies.

Getting Started

This Installation Manual explains how to operate an IPELA HYBRID-compatible hybrid
camera receiver.

Features

SNCA-ZX104 and SNCA-ZP104 are IPELA HYBRID-compatible hybrid camera



receivers.
The IPELA HYBRID-compatible camera connected to this unit’s SLOC port connects



to an external network via this unit’s LAN port. Also, composite video signals from a
camera are output via this unit’s video output terminal.
Up to 4 IPELA HYBRID-compatible cameras can be connected to this receiver.



An IPELA HYBRID-compatible camera’s pan, tilt and zoom, etc., functions can be



controlled from a keyboard connected to this unit.
The Serial PTZ function converts control signals input from the RS-485 port to TCP/



IP packets and sends them via a network. Connect a keyboard compatible with the
Pelco-D protocol to the RS-485 port.
You can control up to 255 Serial PTZ-compatible cameras registered to a single



SNCA-ZX104. (When connecting this unit with multiple receivers, see “Connection”
for details.)
You can control other SNCA-ZP104 and SNCA-ZX104 units via the Serial PTZ



function by using a keyboard connected to a single SNCA-ZX104.

About the Supplied Manuals

Installation Manual (this document)

This Installation Manual describes the names and functions of parts and controls of
the receiver, gives connection examples and explains how to set up the unit. Be sure
to read the Installation Manual before operating.

User’s Guide (stored in the CD-ROM) (SNCA-ZX104 only)

The User’s Guide describes how to set up the receiver and how to control the unit via a
Web browser.
After installing and connecting the receiver correctly, operate by referring to this
User’s Guide.

Using the CD-ROM Manuals

The supplied CD-ROM includes the manual and related documentation for this unit in
PDF format.

Preparations

Adobe Reader Version 6.0 or higher must be installed on your computer in order to
view the manual and related documentation stored in the CD-ROM.

Note

If Adobe Reader is not installed, it may be downloaded from the following URL:

http://www.adobe.com/

Reading the manual in the CD-ROM

1

Insert the CD-ROM in your CD-ROM drive.
A cover page appears automatically in your Web browser.
If it does not appear automatically in the Web browser, double-click on the index.
htm file on the CD-ROM.

2

Select and click on the manual that you want to read.
This opens the PDF file of the manual.
Clicking an item in the Table of Contents allows you jump to the relevant page.

Notes

The files may not be displayed properly, depending on the version of Adobe Reader.



In this case, install the latest version, which you can download from the URL
mentioned in “Preparations” above.
If you have lost or damaged the CD-ROM, you can purchase a replacement. Contact



your Sony service representative.

When installing the installation space must be secured in consideration of the
ventilation and service operation.

Do not block the ventilation slots at the left side and right side panels, and vents of



the fans.
Leave a space around the unit for ventilation.



Leave more than 15 cm (6 in) of space in the rear of the unit to secure the operation



area.
When the unit is installed on the desk or the like, leave at least 2 cm (
the left and right sides.
Leaving 40 cm (15
operation.

3

/4 in) or more of space above the unit is recommended for service

13

/16 in) of space in

WARNING

THIS WARNING IS APPLICABLE FOR USA ONLY.
If used in USA, use the UL LISTED power cord specified below.
DO NOT USE ANY OTHER POWER CORD.

Plug Cap Parallel blade (NEMA 1-15P Configuration)
Cord Type NISPT-2 or SPT-2, two 16 or 18 AWG wires
Length Minimum 1.5 m (4 ft 11 in), Less than 2.5 m (8 ft 3 in)
Rating Minimum 7 A, 125 V

Using this unit at a voltage other than 120 V may require the use of a different line
cord or attachment plug, or both. To reduce the risk of fire or electric shock, refer
servicing to qualified service personnel.

WARNING

THIS WARNING IS APPLICABLE FOR OTHER COUNTRIES.

1. Use the approved Power Cord (2-core mains lead) / Appliance Connector / Plug that

conforms to the safety regulations of each country if applicable.

2. Use the Power Cord (2-core mains lead) / Appliance Connector / Plug conforming to

the proper ratings (Voltage, Ampere).

(continued on the reverse side)

If you have questions on the use of the above Power Cord / Appliance Connector /
Plug, please consult a qualified service personnel.

IMPORTANT

The nameplate is located on the bottom.

ATTENTION

The electromagnetic fields at the specific frequencies may influence the picture of this
unit.

A

B

SNCA-ZX104

SNCA-ZP104

C

IPELA HYBRID-compatible camera

Coaxial cable × 4

Location and Function of Parts

Front



POWER indicator (green)

When the receiver receives power, an internal system check is performed.
The indicator lights up when the unit is operating normally.



NETWORK indicator (green)

The indicator lights up or flashes in green when the unit is connected to the network.
The indicator remains off when the unit is not connected to the network.



SLOC indicator (orange)

The indicator lights up in orange when an SLOC connection to a hybrid camera is
established.
The indicator flashes in orange when an SLOC transmission error is occurring.

Rear



SLOC (IP coaxial transfer) port

Use this terminal to connect the unit to an IPELA HYBRID-compatible camera via a
coaxial cable.



DC IN 12 V DC (power input) terminal

Connect to the supplied DC 12 V AC adapter.



Video output terminal (BNC)

Outputs composite video signals.



Reset switch

To reset the unit, press this switch. To restore the unit’s factory default settings, press
this switch for more than 3 seconds.
To push the switch, use a pointed object.



RS-485 selection switch (SNCA-ZX104 only)

Set this switch to ON to enable network functions; this unit’s settings can then be
changed over the network that is connected via the LAN port. This unit’s Serial PTZ
functions are also enabled; the unit can accept input from the keyboard connected to
this unit’s I/O port.
Set this switch to OFF to disable network functions and block input from the I/O port.



I/O (input/output) port (SNCA-ZX104 only)

This unit includes an RS-485 port. You can connect a keyboard that is compatible with
Pelco-D protocol control signals in order to control the unit.

Indication Function

G RS-485 reference GND
+ RS-485 (+) input/output (GND level reference)
– RS-485 (–) input/output (GND level reference)



LAN (network) port (RJ-45)

Connect to a 10BASE-T or 100BASE-TX network using a network cable (UTP, category

5).

Caution

For safety, do not connect the connector for peripheral device wiring that might



have excessive voltage to this port. Follow the instructions for this port.
When you connect the LAN cable of the unit to peripheral device, use a shielded-



type cable to prevent malfunction due to radiation noise.

NC





NOTICE TO USERS
© 2012 Sony Corporation. All rights reserved. This Installation Manual, in whole or in
part, may not be reproduced, translated or reduced to any machine readable form
without prior written approval from Sony Corporation.

SONY CORPORATION PROVIDES NO WARRANTY WITH REGARD TO THIS MANUAL,
THE UNIT OR OTHER INFORMATION CONTAINED HEREIN AND HEREBY EXPRESSLY
DISCLAIMS ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY
PARTICULAR PURPOSE WITH REGARD TO THIS MANUAL, THE UNIT OR SUCH OTHER
INFORMATION. IN NO EVENT SHALL SONY CORPORATION BE LIABLE FOR ANY
INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES, WHETHER BASED ON TORT,
CONTRACT, OR OTHERWISE, ARISING OUT OF OR IN CONNECTION WITH THIS
MANUAL, THE UNIT OR OTHER INFORMATION CONTAINED HEREIN OR THE USE
THEREOF.

Sony Corporation reserves the right to make any modification to this manual or the
information contained herein at any time without notice.

“IPELA”,



Sony Corporation.
Adobe and Adobe Reader are trademarks of Adobe Systems Incorporated in the



United States and/or other countries.
sloc™ is a trademark owned by the Intersil Corporation family of companies.



All other company and product names are trademarks or registered trademarks of
the respective companies or their respective makers.

and are trademarks of

I/O port
connector

To a

Network cable

(straight,

not supplied)

The section within the dotten line applies to
SNCA-ZX104 only.

keyboard

10BASE-T/
100BASE-TX

Hub

Network

D

IPELA HYBRID-compatible camera
(Serial PTZ-compatible)

Camera 1

Camera 2

SNCA-ZX104
(RS-485: On)

SNCA-ZP104 or
SNCA-ZX104 (RS-485: Off )

Coaxial cable × 4

To an analog
monitor

To power
socket

Keyboard

Network

AC adaptor

Connection

Connecting to the Network

Connect the unit via its LAN port using a network cable (not supplied).

Connecting to a Monitor

Connect a video output terminal of the unit to an analog monitor using a coaxial cable
(not supplied).

Connecting to an IPELA HYBRID-compatible Camera

Connect a SLOC port of the unit to an IPELA HYBRID-compatible camera’s SLOC port
using a coaxial cable (not supplied).
The maximum coaxial cable length is RG-59 300 m.

Note

The high-frequency characteristics of coaxial cables may differ, even if the cables are of
the same classification. Use a high-quality, high-frequency coaxial cable with this unit.

For details on coaxial cables and cameras that can be connected to this unit, refer to the
instruction manual of the connecting SLOC device. For further details, please consult an
authorized Sony dealer.

Connecting to a Keyboard (SNCA-ZX104)

Using the supplied I/O port connector, connect a keyboard (not supplied) that
supports the Pelco-D protocol, and set the RS-485 selection switch to ON.
Set the RS-485 selection switch of SNCA-ZX104 units without connected keyboards to
OFF.

For details on settings related to the Serial PTZ function and settings related to connecting
the keyboard, refer to the SNCA-ZX104 User’s Guide.
For details on camera settings related to Serial PTZ, refer to the camera’s Instruction
Manual.

Connecting the Power Source

Connect to the supplied DC 12 V AC adapter.

Connecting multiple receivers and using the Serial PTZ
function

Using an SNCA-ZX104 as the first receiver, set its RS-485 switch to On, and then
connect the keyboard.
An SNCA-ZX104 with its rear RS-485 switch set to Off, or an SNCA-ZP104 can then be
connected and used.
For details on setting the receiver’s Serial PTZ function, refer to the SNCA-ZX104 User’s
Guide. For details on settings for the connected camera(s), refer to the connected
device’s Instruction Manual.
For compatible IPELA HYBRID cameras, contact your authorized Sony dealer.

Specifications

Camera 3

Camera N

Camera N+1

Camera 255

E

SNCA-ZP104 or
SNCA-ZX104 (RS-485: Off )

SNCA-ZP104 or
SNCA-ZX104 (RS-485: Off )

SLOC (IP coaxial
transfer)

SNCA-ZX104

SNCA-ZP104

)

8

/

7

250 (9

Hub

Interface

SLOC input BNC ×4, 75Ω termination
Analog video output BNC ×4, composite 1.0 Vp-p, 75Ω termination
Network port 10BASE-T/100BASE-TX, auto negotiation (RJ-45)
I/O port (SNCA-ZX104 only) Camera control interface: ×1 (RS-485)

Others

Power supply DC 12V
Consumption current 0.7 A
Operating temperature 0 °C to 45 °C (32 °F to 113 °F)
Storage temperature –20 °C to +60 °C (–4 °F to +140 °F)
Operating humidity 20% to 80% (no condensation)
Storage humidity 20% to 80% (no condensation)

Dimensions

Mass Approximately 1.2 kg
Supplied accessories



210 × 44 × 250 mm (8
(without the projecting parts)

CD-ROM (User’s Guide and supplied programs) (1)
Installation Manual (this document) (1)
B&P Warranty Booklet (1)
AC adaptor (AC-NB12A) (1)
Power cord (1)
I/O port connector (SNCA-ZX104 only) (1)

Note

This package may contain additional installation
manuals and/or documentation.

3

/8 × 1 3/4 × 9 7/8 in) (w/h/d)

AC adaptor (AC-NB12A)

Power supply AC 100 to 240 V, 50/60 Hz

Output DC 12 V, 2.5 A
Operating temperature 0 °C to 45 °C (32 °F to 113 °F)
Operating humidity 20% to 80% (no condensation)
Storage temperature –20 °C to +60 °C (–4 °F to +140 °F)
Storage humidity 20% to 80% (no condensation)
Dimensions 49.5 × 28 × 99.5 mm (2 × 1

Mass Approximately 0.2 kg (7 oz)

Design and specifications are subject to change without notice.

Recommendation of Periodic Inspections

In case using this device over an extended period of time, please have it inspected
periodically for safe use.
It may appear flawless, but the components may have deteriorated over time, which
may cause a malfunction or accident.
For details, please consult the store of purchase or an authorized Sony dealer.

0.65 A to 0.35 A

the projecting parts)

1

/8 × 4 in) (w/h/d) (without

210 (8 3/8)

)

4

/

3

44

(1

Unit: mm (inches)