Sony SLV-ED925PS, SLV-ED225PS, SLV-ED825PS, SLV-ED828ME-SG, SLV-ED929MI User Manual

3-073-156-11 (1) GB
Video Cassette Recorder
Operating Instructions
SLV-ED929MI SLV-ED925PS SLV-ED828ME/SG SLV-ED825PS SLV-ED323ME/SG SLV-ED225PS
© 2002 Sony Corporation
WARNING
To prevent fire or shock hazard, do not expose the unit to rain or moisture.
To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.
The mains lead must only be changed at a qualified service shop.
Precautions
Safety
This unit operates on 110 – 240 V AC, 50/ 60 Hz. Check that the units operating voltage is identical with your local power supply.
If anything falls into the cabinet, unplug the unit and have it checked by qualified personnel before operating it any further.
The unit is not disconnected from the mains as long as it is connected to the mains, even if the unit itself has been turned off.
Unplug the unit from the mains if you do not intend to use it for an extended period of time. To disconnect the lead, pull it out by the plug, never by the lead.
To prevent fire or shock hazard, do not place objects filled with liquids, such as vases, on the apparatus.
Installing
Allow adequate air circulation to prevent internal heat buildup.
Do not place the unit on surfaces (rugs, blankets, etc.) or near materials (curtains, draperies) that may block the ventilation slots.
Do not install the unit near heat sources such as radiators or air ducts, or in a place subject to direct sunlight, excessive dust, mechanical vibration or shock.
Do not install the unit in an inclined position. It is designed to be operated in a horizontal position only.
Keep the unit and cassettes away from equipment with strong magnets, such as microwave ovens or large loudspeakers.
Do not place heavy objects on the unit.
If the unit is brought directly from a cold
to a warm location, moisture may condense inside the VCR and cause damage to the video head and tape. When you first install the unit, or when you move it from a cold to a warm location, wait for about four hours before operating the unit.
Caution
Television programmes, films, video tapes and other materials may be copyrighted. Unauthorized recording of such material may be contrary to the provisions of the copyright laws. Also, use of this recorder with cable television transmission may require authorization from the cable television transmitter and/or programme owner.
Compatible colour/TV systems
This VCR is designed to record and play back using the PAL (B/G, D/K and I), MESECAM (B/G and D/K) and NTSC (M*) colour systems. Recording of video sources based on other colour systems cannot be guaranteed.
* SLV-ED929MI only For SLV-ED925PS, ED828ME/SG,
ED825PS, ED323ME/SG and ED225PS
NTSC colour signals can only be recorded through the line input.
G-CODE is a registered trade mark of Gemstar Development Corporation. The G-CODE system is manufactured under license from Gemstar Development Corporation.
WARNING
2
Table of Contents
Getting Started
Getting Started
4 Index to parts and controls
10 Step 1 : Unpacking 11 Step 2 : Setting up the remote
commander
13 Step 3 : Connecting the VCR 15 Step 4 : Setting up the VCR with
the Auto Set Up function
18 Step 5 : Setting the clock 20 Step 6 : Selecting the TV
system
21 Selecting a language
(SLV-ED828ME/SG and ED323ME/SG only)
22 Presetting channels 25 Changing/disabling programme
positions
Basic Operations
30 Playing a tape 32 Recording TV programmes 36 Recording TV programmes using
the Easy Timer
42 Recording TV programmes using
the G-CODE® system (SLV-ED929MI only)
45 Recording TV programmes using
the timer
Additional Operations
48 Playing/searching at various speeds 49 Setting the recording duration time 50 Checking/changing/cancelling
timer settings
52 Recording stereo and bilingual
programmes (not available on SLV­ED323ME/SG and ED225PS)
55 Searching using the index function 56 Adjusting the picture 57 Reducing the VCRs power
consumption
58 Changing menu options
Editing
60 Connecting to a VCR or stereo
system
62 Basic editing
Additional Information
63 Troubleshooting 67 Specifications Back cover
Index
Table of contents
3

Getting Started

Index to parts and controls

Refer to the pages indicated in parentheses ( ) for details.
Front panel
For SLV-ED929MI, ED925PS, ED828ME/SG and ED825PS
1 ?/1 ON/STANDBY switch 2 Remote sensor (11) 3 Tape compartment 4 A EJECT button (30) 5 H PLAY button*1 (30) (48) 6 x STOP button*1 (17) (30) (62) 7 z REC (record) button (33) (49)
(62)
8 X PAUSE button (30) (41) (62)
Getting Started
4
9 M FF (fast-forward) button (30)
(48)
q; m REW (rewind) button (30) (48) qa EASY TIMER (36) qs PROGRAM/TRACKING +/–
buttons*1 (37) (56)
qd LINE-2 IN VIDEO/AUDIO L/R
(left/right) jacks*2 (60) (61)
*1The H PLAY, x STOP and PROGRAM/
TRACKING + buttons have a tactile dot.
2
not available on SLV-ED825PS
*
For SLV-ED323ME/SG and ED225PS
Getting Started
1 ?/1 ON/STANDBY switch 2 A EJECT button (30) 3 Remote sensor (11) 4 Tape compartment 5 m REW (rewind) button (30) (48) 6 H PLAY button (30) (48) 7 M FF (fast-forward) button (30)
(48)
8 z REC (record) button (33) (49)
(62)
9 x STOP button (17) (30) (62) q; X PAUSE button (30) (41) (62) qa EASY TIMER (36) qs PROGRAM/TRACKING +/–
buttons* (37) (56)
* The PROGRAM/TRACKING + button
has a tactile dot.
continued
Getting Started
5
Index to parts and controls (continued)
Display window
31452678
90qa
1 Tape indicator 2 START indicator (37) 3 STOP indicator (37) 4 MONTH indicator (40) 5 YEAR indicator 6 NICAM indicator*1 (53) 7 STEREO indicator*2 (52)
8 Timer indicator (39) (43) (46) 9 Recording indicator (33) q; Time counter/clock/line/programme
position indicator (31) (32) (62)
qa Tape speed indicators (32) (38)
*1SLV-ED929MI and ED925PS only
2
not available on SLV-ED323ME/SG and
*
ED225PS
Getting Started
6
Rear panel
For SLV-ED929MI, ED925PS, ED828ME/SG and ED825PS
Getting Started
21
45
For SLV-ED323ME/SG and ED225PS
45
3
321
1 (in from antenna) connector (13) 2 LINE IN 1 AUDIO R/L/VIDEO
(audio right/audio left/video) jacks* (61) LINE IN 1 AUDIO/VIDEO jacks* (60)
3 Mains lead (13)
4 LINE OUT AUDIO R/L/VIDEO
(audio right/audio left/video) jacks*
1
LINE OUT AUDIO/VIDEO jacks* (14)
2
5 (out to tv) connector (13)
*1SLV-ED929MI, ED925PS, ED828ME/SG
and ED825PS only
2
SLV-ED323ME/SG and ED225PS only
*
2
continued
Getting Started
1
7
Index to parts and controls (continued)
Remote commander
123 456 789
0
1 Z EJECT button (30) 2 INPUT SELECT button (32) (45)
(62)
3 TV/VIDEO button (for TV) 4 CLEAR button (31) (42) (50) 5 Programme number buttons* (42) 6 -/-- (tens digit) button 7 VOL (volume) +/ buttons 8 z REC (record) button (33) (49) 9 REC SPEED (recording speed)
button (32)
q; MENU button (21) (50) qa X PAUSE/M button (21) (30)
x STOP/m button (21) (30) m REW (rewind)/< button (21)
(30) (48) M FF (fast-forward)/, button (21) (30) (48) H PLAY/OK button* (21) (30) (48)
* The H PLAY, AUDIO MONITOR,
number 5 and PROG + buttons have a tactile dot.
Getting Started
8
123 456 789
0
qs ?/1 (on/standby) switch (43) qd TV/VIDEO remote control switch
(11)
qf AUDIO MONITOR button*1*2 (52) qg G-CODE button*3 (42) qh DISPLAY button (31) (33) qj PROG (programme) +/– buttons*
1
(34)
qk y SLOW button (48) ql ×2 button (48) w; ./> INDEX SEARCH
buttons (55)
*1The H PLAY, AUDIO MONITOR,
number 5 and PROG + buttons have a tactile dot.
*2not available on SLV-ED323ME/SG and
ED225PS
3
SLV-ED929MI only
*
Getting Started
Getting Started
9

Step 1 : Unpacking

Check that you have received the following items with the VCR:
Remote commander Aerial cable
R6 (size AA) batteries • Plug adaptor (SLV-ED828ME and
ED323ME only)
Check your model name
The instructions in this manual are for the 8 models: SLV-ED929MI, ED925PS, ED828ME/SG, ED825PS, ED323ME/SG and ED225PS. Check your model name by looking at the rear panel of your VCR. SLV-ED929MI is the model used for illustration purposes. Any difference in operation is clearly indicated in the text, for example, SLV-ED929MI only.
Getting Started
10
Step 2 : Setting up the remote
commander
Inserting the batteries
Insert two R6 (size AA) batteries by matching the + and – on the batteries to the diagram inside the battery compartment.
Insert the negative (–) end first, then push in and down until the positive (+) end clicks into position.
Getting Started
Using the remote commander
Remote sensor
You can use this remote commander to operate this VCR and a Sony TV. Buttons on the remote commander marked with a dot (•) can be used to operate your Sony TV. If the TV does not have the symbol near the remote sensor, this remote
•TV/VIDEO
commander will not operate the TV.
123 456 789
0
To operate Set •TV/VIDEO to
the VCR VIDEO and point at the remote sensor at the VCR a Sony TV TV and point at the remote sensor at the TV
continued
Getting Started
11
Step 2 : Setting up the remote commander (continued)
Notes
With normal use, the batteries should last about three to six months.
If you do not use the remote commander for an extended period of time, remove
the batteries to avoid possible damage from battery leakage.
Do not use a new battery together with an old one.
Do not use different types of batteries together.
Some buttons may not work with certain Sony TVs.
Getting Started
12

Step 3 : Connecting the VCR

Connect the aerial to your VCR and TV as shown below to watch TV programmes and VCR pictures on your TV. In addition, if your TV has audio/video (A/V) input jacks, we recommend you connect the VCR to your TV using an audio/video cable to get a better picture and sound.
Connecting the aerial
Getting Started
Mains lead
AERIAL IN
Aerial cable (supplied)
: Signal flow
1 Disconnect the aerial cable from your
TV and connect it to on the rear panel of the VCR.
2 Connect of the VCR and the aerial
input of your TV using the supplied aerial cable.
3 Connect the mains lead to the mains.
Note
When you connect the VCR and your TV only with an aerial cable, you have to tune your TV to the VCR (see page 15).
to mains
continued
Getting Started
13
Step 3 : Connecting the VCR (continued)
Additional connections
To a TV that has audio/ video input jacks
This additional connection improves picture and sound quality. Connect the TV as shown on the right.
To a stereo system (not available on SLV­ED323ME/SG and ED225PS)
You can improve sound quality by connecting a stereo system to the LINE OUT AUDIO R/L jacks as shown on the right.
For SLV-ED929MI, ED925PS, ED828ME/SG and ED825PS
LINE OUT
Audio/video cable (not supplied)
For SLV-ED323ME/SG and ED225PS
LINE OUT
Audio/video cable (not supplied)
LINE OUT AUDIO R/L
Audio cable (not supplied)
LINE IN
LINE IN
LINE IN
Getting Started
14
Note
To play a tape in stereo, you must connect your VCR either to a TV with audio/
video input jacks or to a stereo system as shown on above right.
Step 4 : Setting up the VCR with
EXIT MENU:OK:SET
SELECT
ENGLISH ARABIC
:
the Auto Set Up function
Before using the VCR for the first time, set up the VCR using the Auto Set Up function. With this function, you can set the language for the on-screen display and TV channels automatically.
1 Turn on your TV and set it to the video channel.
Tune the TV to channel 51 (for SLV-ED929MI, ED925PS, ED825PS and ED225PS) or 32 (for SLV-ED828ME/SG and ED323ME/SG) (the initial RF channel for this VCR). Refer to your TV manual for TV tuning instructions. If the picture does not appear clearly, see “To change the RF channel on page 17.
2 Connect the mains lead to the mains.
PLAY
OK
The VCR automatically turns on.
For SLV-ED929MI, ED925PS, ED825PS and ED225PS
The message for the Auto Set Up function appears on the TV screen.
For SLV-ED828ME/SG and ED323ME/SG
The LANGUAGE SET menu appears on the TV screen.
Press </, to select the desired language, ENGLISH or ARABIC, then press OK.
The message for the Auto Set Up function appears.
Getting Started
continued
Getting Started
15
END MENU:OK:EXECUTE
SELECT
SYSTEM–B/G SYSTEM–D/K SYSTEM–I SYSTEM–B/B U.S–ANT. U.S–HRC U.S–IRC JAPAN
:
SYSTEM SELECT
MENU:
PLEASE WAIT
AUTO SET UP
40%
EXIT
EXIT MENU:OK:SET
SELECT
SYSTEM SYSTEM SYSTEM
:
SYSTEM SELECT
– B/G
D/K
I
Step 4 : Setting up the VCR with the Auto Set Up function (continued)
3 Press OK.
PLAY
OK
The SYSTEM SELECT menu appears.
For SLV-ED929MI
For SLV-ED925PS, ED828ME/SG, ED825PS, ED323ME/SG and ED225PS
4 Press M/m/</, to select the
PLAY
OK
appropriate TV system, then press OK.
The VCR starts searching for all of the receivable channels and presets them (in the appropriate order for your local area).
If you want to change the order of the channels or disable unwanted programme positions, see Changing/disabling programme positions on page 25.
After the search is complete, the clock setting menu appears. See Setting the clock on page 18.
Getting Started
16
To cancel the Auto Set Up function
Press MENU.
To change the RF channel
If the picture does not appear clearly on the TV, change the RF channel on the VCR and TV. Select INSTALLATION from the menu, then press M/m to highlight VCR OUTPUT CH and press ,. Select the RF channel by pressing the M/m buttons. Then, tune the TV to the new RF channel so that a clear picture appears.
Tip
If you want to change the language for the on-screen display from the one preset in the Auto Set Up function, see page 21.*
Notes
Whenever you operate the Auto Set Up function, some of the settings (timer, etc.) will be reset. If this happens, you have to set them again.
Auto preset starts automatically only when you plug in the mains lead for the first time after you purchase the VCR.
After using the Auto Set Up function, the LANGUAGE SET menu* does not appear automatically when you connect the mains lead again. If you want to use the Auto Set Up function again, press MENU, then press M/m/</, to highlight INSTALLATION and press OK. Press M/m to highlight AUTO SET UP, then repeat all procedures from step 3.
Auto preset can be performed by pressing x STOP 5 seconds or more with no tape inserted.
* SLV-ED828ME/SG and ED323ME/SG only
on the VCR continuously for
Getting Started
Getting Started
17
SET
MENU:
:
OK:END
SELECT
12 0 1 JAN/0:20
TUE
02/
:
EXIT
SET
MENU:
:
OK:END
SELECT
18 0 1 JAN/0:20
TUE
02/
:
EXIT
SET
MENU:
:
OK:END
SELECT
18 3 1 JAN/0:20
TUE
02/
:
EXIT

Step 5 : Setting the clock

You must set the time and date on the VCR to use the timer features properly.
Before you start
Turn on the VCR and the TV.
Set the TV to the video channel.
Refer to Index to parts and controls for button locations.
1 Press MENU, then press M/m/</
MENU
, to highlight CLOCK SET and press OK.
PLAY
OK
2 Press M/m to set the hour.
PLAY
OK
3 Press , to select the minutes and
PLAY
OK
set the minutes by pressing M/m.
Getting Started
18
SET
MENU:
:
OK:END
SELECT
18 3 82 SEP/0:20
SAT
02/
:
EXIT
4 Set the day, month, and year in
PLAY
OK
sequence by pressing , to select the item to be set, and press M/m to select the digits, then press ,.
The day of the week is set automatically.
Getting Started
5 Press MENU to exit the menu.
MENU
Tip
To change the digits while setting, press < to return to the item to be changed, and select the digits by pressing M/m.
Getting Started
19

Step 6 : Selecting the TV system

SET
MENU:
:
OK:END
SELECT
AUTO SET UP MANUAL SET UP TV SYSTEM
32:
G:
VCR OUTPUT CH
:
EXIT
SET
MENU:
:
OK:END
SELECT
AUTO SET UP MANUAL SET UP TV SYSTEM
32:
G:
VCR OUTPUT CH
:
EXIT
You must select the appropriate TV system for your area.
Before you start
Turn on the VCR and the TV.
Set the TV to the video channel.
Refer to Index to parts and controls for button locations.
1 Press MENU, then press M/m/</
MENU
, to highlight INSTALLATION and press OK.
PLAY
OK
2 Press M/m to highlight TV
PLAY
OK
SYSTEM, then press ,.
3 Press , to select the appropriate TV system.
PLAY
OK
Select For
G the B/G TV system K the D/K TV system I the I TV system B* the B/B TV system M* the U.S–ANT., U.S–HRC, U.S–IRC and JAPAN TV
systems
4 Press MENU to exit the menu.
* SLV-ED929MI only
Getting Started
20
MENU
Selecting a language (SLV-ED828ME/SG
EXIT MENU:OK:SET
SELECT
ENGLISH ARABIC
:
and ED323ME/SG only)
You can change the on-screen display language from the one you selected with the Auto Set Up function.
Before you start
Turn on the VCR and the TV.
Set the TV to the video channel.
Refer to Index to parts and controls for button locations.
Getting Started
1 Press MENU, then press M/m/</
MENU
, to highlight LANGUAGE SET and press OK.
PLAY
OK
2 Press </, to highlight the desired language, ENGLISH or
PLAY
OK
ARABIC, then press OK.
Getting Started
21
Loading...
+ 47 hidden pages