Using your Style Cover Window in wet and dusty conditions.........9
Declaration of Conformity ...............................................................11
2
Getting started
Introduction
The Style Cover Window is a smart cover for your Xperia™ Z5 Compact smartphone
that lets you view and use dedicated functions. When you close the cover, the
smart window function becomes active and selected widgets from your
smartphone status bar or Home screen appear in the window. You can then
interact with these selected widgets and associated functions. For example, you
can see and read an incoming message, activate your smartphone camera, control
your music, and answer an incoming call – all without opening the cover.
Overview
1Window
2NFC™ detection area
One-touch setup
With one-touch setup, all you have to do is touch the NFC area of your smartphone
to the NFC area of the Style Cover Window. The NFC function launches the setup
procedure and you can then customise your smart window functions and settings.
To set up the Style Cover Window for use
1Open the Style Cover Window accessory.
2Make sure that the NFC function on the phone is turned on and that the
screen is active and unlocked, then place the back of the phone over the NFC
detection area of the accessory, as indicated in the illustration. The NFC area
of each device should touch the other.
1Position the back of the phone over the back cover of the accessory so that
the camera lens is aligned with the camera lens hole of the accessory.
2Press down firmly on all edges of the phone to make sure it gets properly
attached.
Charging
Before you attach the Style Cover Window and use it for the first time, make sure
the smartphone that you want to use with it is fully charged. The Style Cover
Window does not work if your smartphone has no power.
To charge your phone using a DK52 USB Charging Dock
1Make sure that the Style Cover Window is properly attached to your phone
and that the cover is closed.
2Insert the attachment into the charging dock.
3Plug one end of the USB charger cable into the charging dock.
4Plug the other end of the charger cable into the USB port of a computer or a
phone charger. Make sure the charger or computer is connected to an active
power source.
5Place your phone in the dock in such a way that the charging dock connector
on the phone makes contact with the connector in the dock.
Once the Style Cover Window is set up and attached to your phone, you have to
close the cover to activate the smart window function. When the smart window
function is active, the display of your phone is shrunk to fit in the window of the
cover. This window is similar to a mini version of your phone screen and you can
interact with it in the same way. For example, you can swipe on or tap the window
screen to navigate your way around.
Swiping
•See more widgets and other actions.
Tapping
•Open or select an item.
Dimming and waking up the screen
When the Style Cover Window is attached and left idle for a certain period of time,
the window screen dims automatically. You can also dim the window screen
manually and wake it up at any time.
To wake up the window screen
1On your Xperia™ smartphone, make sure that Tap to wake up mode is
turned on. To turn it on, tap Settings > Display, then drag the slider beside
Tap to wake up to the right.
2Double-tap the window screen or briefly press the power key.
When the Style Cover Window is attached and the smart window function is active,
a Home screen appears in the window. This Home screen is the main screen from
which you can navigate to other screens and take various actions. It is similar to
the Home screen of your phone. From here, you can, for example, view
notifications of missed calls or unread SMS messages and take pictures.
When a call comes in on your smartphone, you can see who is calling on the
screen of the Style Cover Window. You can then interact with the window screen to
accept or reject the call.
To answer an incoming call
•To accept the incoming call, slide from left to right on the window screen.
To decline an incoming call
•Slide from right to left on the window screen.
Answering a video call
When a video call comes in while the Style Cover Window is attached, you are
prompted to open the cover to launch the front camera on your phone.
To answer a video call
•Open the cover of the Style Cover Window and look into the front camera on
your phone.
Camera
From the Home screen of the Style Cover Window, you can launch the camera
application and take pictures in portrait or landscape orientation.
To take a photo from the Home screen of the Style Cover Window
1
To activate the window screen, briefly press the power key
2To activate the camera, touch and hold , then drag upwards.
3After the camera opens, locate your subject in the viewfinder.
4Once you are ready to take the photo, tap
.
Alarm
You can view an activated alarm from the Home screen of the Style Cover Window.
To set an alarm, you must first access the smartphone, that is, when the cover is
open or not attached.
To set an alarm
1Open the front cover of your accessory so that you can access the Home
screen of your phone directly.
2From the Home screen of your phone, tap
3Find and tap Alarm & clock.
4
Tap
5Tap Time and adjust the time by scrolling up and down.
6Tap Set.
7If desired, edit other alarm settings.
8Tap Done. This alarm is now displayed on the Home screen of the Style
2From the Home screen of your phone, drag down the status bar to open the
Notification panel, then tap .
Music player
You can access the music player application directly from the Home screen of the
Style Cover Window.
To access the music player
•Swipe from right to left on the Home screen of the Style Cover Window.
Widgets
Widgets are small applications that you can use directly on the window screen.
They also function as shortcuts. For example, the Calendar widget allows you to
see basic calendar information directly on the window screen. You can download
additional widgets from Google Play™.
To add a widget to the window screen
1
To activate the window screen, briefly press the power key
2Swipe to the right until appears, then tap it. You are then prompted to
open the cover to add a widget directly on your phone.
3If required, enter your PIN code, pattern or password to unlock the screen of
your phone.
4Find and tap the widget that you want to add.
.
The items that appear when you tap
To move a widget on the window screen
1
To activate the window screen, briefly press the power key
2Touch and hold the widget that you want to move, then drag it to the new
location.
To remove a widget from the window screen
1
To activate the window screen, briefly press the power key .
2Touch and hold the widget that you want to remove, then drag it to
The camera icon and the music player appear on the screen by default and cannot be
removed.
are available by default and cannot be modified.
.
Disabled smartphone features
The Smart call handling and Glove mode features get disabled when the cover of your
accessory is closed. For more information about these features, refer to the User guide for
your phone.
Using your Style Cover Window in wet and dusty conditions
Your Style Cover Window is waterproof in compliance with the Ingress Protection
(IP) ratings IPX5 and IPX8, as explained in the table below.
These specific IP ratings mean that your Style Cover Window is protected against
low pressure water stream as well as against the eects of immersion for 30
minutes in fresh (non-saline) water up to 1.5 metres deep.
Even if your Style Cover Window is resistant to water, you should avoid using it
unnecessarily in or under water and should avoid exposing it to moist
environments with extreme high or low temperatures and high humidity.
Never immerse your Style Cover Window in hot water, non-fresh water (for
example, spring water, chlorinated pool water and sea water) or other kinds of
water that could damage it. Also, never expose the Style Cover Window to any
liquid chemicals, for example, detergent, alcohol and other abrasive liquids such as
juice, vinegar and ketchup. After exposure to non-fresh water, rinse your Style
Cover Window using fresh water.
If your Style Cover Window gets exposed to water, make sure it is completely dry
before using it again. For example, if the Style Cover Window has not completely
dried, it may not respond when you tap the window, or functions such as data
transfer and calling might be negatively impacted.
Do not attach the Style Cover Window to or remove it from your Xperia™ device
using excessive force or a method not described in this User guide.
Use a soft, dry cloth for cleaning all areas of your Style Cover Window. To prevent
colour fading, do not wipe the accessory with alcohol, thinner, benzene or any kind
of detergent.
Do not expose the Style Cover Window unnecessarily to environments with
excessive dust, sand and mud.
If sand, mud or dust gets stuck between the front cover of the Style Cover Window
and your Xperia™ device, wipe it o with a soft cloth. Otherwise, there is a risk that
your Xperia™ device and the Style Cover Window might incur scratch damage.
There is a possibility of discolouration or colour migration due to friction, sweating
and exposure to non-fresh water. Be mindful of this if you are using the Style Cover
Window in close proximity to fabrics and other materials.
These instructions for use in wet and dusty conditions apply only to use of the Style Cover
Window. Your Xperia™ device may have its own instructions and restrictions on use in wet
and dusty conditions. Please ensure you check these too before exposing the device to
such conditions.
Your warranty does not cover damage or defects caused by abuse or improper use
of your Style Cover Window (including use in environments where the relevant IP
rating limitations are exceeded). If you have any further questions about the use of
your accessory, refer to our Customer support service for help.
Ingress Protection Rating
Your Style Cover Window has an IP rating in accordance with IEC Standard 60529,
which means it has undergone certified tests to measure its resistance levels to
both dust and water. The first digit in the two-digit IP rating indicates the level of
protection against solid objects, including dust. The second digit indicates how
resistant the device is to water.
Resistance to solid objects and dust
IP0X: No special protectionIPX0. No special protection
IP1X. Protected against solid objects
> 50 mm in diameter
IPX1. Protected against dripping water
IP2X. Protected against solid objects >
12.5 mm in diameter
IP3X. Protected against solid objects >
IPX2. Protected against dripping water when tilted up to 15
degrees from normal position
IPX3. Protected against spraying water
2.5 mm in diameter
IP4X. Protected against solid objects > 1
IPX4. Protected against splashing water
mm in diameter
IP5X. Protected against dust; limited
IPX5. Protected against water jet spray for at least 3 minutes
ingress (no harmful deposit)
IP6X. Dust tightIPX6. Protected against heavy jet spray for at least 3 minutes
IPX7. Protected against the eects of immersion in up to 1
metre of water for 30 minutes
IPX8. Protected against the eects of continued immersion
in water depths greater than 1 metre. The exact conditions
are specified for each device by the manufacturer.
Sony SCR44
Prior to use, please read the
This User guide is published by Sony Mobile Communications Inc. or its local aliated company, without
any warranty. Improvements and changes to this User guide necessitated by typographical errors,
inaccuracies of current information, or improvements to programs and/or equipment, may be made by
Sony Mobile Communications Inc. at any time and without notice. Such changes will, however, be
incorporated into new editions of this User guide.
Sony is the trademark or registered trademark of Sony Corporation.
All product and company names mentioned herein are the trademarks or registered trademarks of their
respective owners. Any rights not expressly granted herein are reserved. All other trademarks are property
of their respective owners.
www.sonymobile.com
Visit
All illustrations are for illustration only and may not accurately depict the actual accessory.
declare under our sole responsibility that our product
Sony type AI-0094
and in combination with our accessories, to which this declaration relates is in
conformity with the appropriate standards
SpectrumEMCSafety
EN 302 291-2:V1.1.1 EN 301 489-7:V1.3.1 EN 60950-1:2006 +A11:2009+A1:2010+A12:2011+A2:2013
EN 301 489-3:V1.6.1
following the provisions of, Radio Equipment and Telecommunication Terminal
Equipment directive 1999/5/EC.
Lund, July 2015
Fredrik Björk
Head of Product Compliance Lund
FCC Statement
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) This device must accept any interference received,
including interference that may cause undesired operation.
Any change or modification not expressly approved by Sony may void the user's authority to operate the
equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment o and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
Industry Canada Statement
This device complies with RSS-210 of Industry Canada.
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this
device must accept any interference, including interference that may cause undesired operation of the
device.
This Class B digital apparatus complies with Canadian ICES-003.
Avis d’industrie Canada
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de
licence.
L'exploitation est autorisée aux deux conditions suivantes:(1) l'appareil ne doit pas produire de brouillage,
et, and (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage
est susceptible d'en compromettre le fonctionnement.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.