Sony SCD-XA777ES User Manual

Super Audio CD Player

4-235-066-23(1)

Operating Instructions

Mode d’emploi

Bedienungsanleitung

Manual de instrucciones

SCD-XA777ES SCD-XA333ES

 2001 Sony Corporation

WARNING

Welcome!

To prevent fire or shock hazard, do not expose the unit to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.

To prevent fire, do not Cover the ventilation of the apparatus with news papers, table-cloths, curtains, etc. And don’t place lighted candles on the apparatus.

To prevent fire or shock hazard, do not place objects filled with liquid, such as vases, on the apparatus.

This appliance is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT MARKING is located on the rear exterior.

Thank you for purchasing the Sony Super Audio CD Player. Before operating the unit, please read this manual thoroughly and retain it for future reference.

About This Manual

The instructions in this manual are for SCD-XA777ES and SCD-XA333ES. SCDXA777ES is the model used for illustration purposes only. Any difference in operation is clearly indicated in the text, for example, “SCD-XA777ES only.”

Conventions

• Instructions in this manual describe the controls on the player. You can also use the controls on the remote if they have the same or similar names as those on the player.

• The following icons are used in this manual:

Indicates that you can do the

task using the remote.

Don’t throw away the battery with general house waste, dispose of it correctly as chemical waste.

Indicates hints and tips for

making the task easier.

Features

TABLE OF CONTENTS

About the Super Audio CD

• Super Audio CD is a new high-quality audio disc standard where music is recorded in the DSD (Direct Stream Digital) format (conventional CDs are recorded in the PCM format). The DSD format, using a sampling frequency 64 times higher than that of a conventional CD, and with 1-bit quantization, achieves both a wide frequency range and a wide dynamic range across the audible frequency range, and so provides music reproduction extremely faithful to the original sound.

• The Super Audio CD has two types; a 2 channel stereo disc and a Multi-channel disc which holds up to 6 independent channels. The multi-channel characteristic of the Super Audio CD features a speaker allocation system basically similar to the 5.1 channel output of current AV systems.

Features of the player

This player is designed to play back 2-channel and multichannel Super Audio CDs, and conventional CDs, and provides the following features:

• Mounted with a Discrete Dual Laser Optical Pickup, capable of reading a Super Audio CD or conventional CD depending on the exclusive wavelength.

• Quicker track access performance enabled by an advanced servo mechanism.

• A Multi-Channel Management function that allows you to adjust the multi-channel playback environment according to the allocation and size of your speakers.

• A Super Audio D/A Converter and Direct Digital Sync System, which allows higher-quality sound reproduction.

Getting Started 4

Before You Start the Hookup 4 Hooking Up the Audio Components 5

Location and Functions of Parts 8

Front Panel Parts Descriptions 8 Rear Panel Parts Descriptions 10 Remote Parts Descriptions 11

Playing Discs 12

Compatible Disc Types 12 Playing a Disc 14 Using the Display 15 Locating a Specific Track 18 Locating a Particular Point in a Track 18 Playing Tracks Repeatedly 19 Playing Tracks in Random Order (Shuffle Play) 20 Creating Your Own Programme (Programme

Play) 21

Listening to a CD Using a Filter (Digital Filter

Function) 22 Setting the DIGITAL OUT to on/off 22 Selecting the default playback area 22 Listening to a Multi-channel Super Audio CD

(Multi-channel management function) 23

Others

• A Super Audio CD can mark up to 255 track/index numbers. This feature applies to SCD-XA777ES/ XA333ES.

• The supplied remote is capable of controlling both the SCD-XA777ES/XA333ES and a conventional Sony CD player.

Additional Information 26

Precautions 26 Notes on Discs 27 Troubleshooting 28 Specifications 28 Index 29

Getting

Before You Start the Hookup

Started

This chapter provides information on the supplied accessories and how to connect various audio components to the Super Audio CD player. Be sure to read this chapter thoroughly before you actually connect anything to the player.

Checking the supplied accessories

This player comes with the following items:

• Audio connecting cord (SCD-XA777ES) phono jack × 2 (Red and White) y phono jack × 2 (Red and White) (3) phono jack × 1 (Black) y phono jack × 1 (Black) (2) (SCD-XA333ES) phono jack × 2 (Red and White) y phono jack × 2 (Red and White) (2) phono jack × 1 (Black) y phono jack × 1 (Black) (2)

• Remote commander RM-SX700 (1)

• R6 (size-AA) batteries (2)

• Mains lead (1) (SCD-XA777ES only)

Inserting batteries into the remote

Insert two R6 (size-AA) batteries into the battery compartment with the + and – correctly oriented to the markings. When using the remote, point it at the remote sensor

on the player.

When to replace the batteries

Under normal conditions, the batteries should last for about six months. When the remote no longer operates the player, replace both batteries with new ones.

Notes

• Do not leave the remote in an extremely hot or a humid place.

• Do not drop any foreign object into the remote casing,

particularly when replacing the batteries.

• Do not use a new battery with an old one.

• Do not expose the remote sensor to direct sunlight or lighting

apparatus. Doing so may cause a malfunction.

• If you do not intend to use the remote for an extended period

of time, remove the batteries to avoid possible damage from battery leakage and corrosion.

Hooking Up the Audio Components

Connect the Super Audio CD player to an audio component. Be sure to turn off the power of all components before making connections and connect securely to prevent noise.

When you have an amplifier equipped with the 5.1CH input jacks (multi-channel amplifier, AV amplifier, etc.) and connect the player and the amplifier via ANALOG

5.1CH OUT jacks, you can play a multi-channel Super Audio CD and enjoy the multi-channel playback. For normal playback, connect the player and an amplifier via ANALOG 2CH OUT jacks.

Connecting via ANALOG 5.1CH OUT jacks

Use audio connecting cords for this connection. Connect the ANALOG 5.1CH OUT jacks (FRONT L/R, SURR L/R, CENTER, SUBWOOFER) to the corresponding jacks of your amplifier. For FRONT or SURR connection, use the connecting cords (Red and White jacks) and be sure to match the colour-coded pin to the appropriate jacks: white (left) to white and red (right) to red. For CENTER and SUB WOOFER connection, use the connecting cords (Black).

FRONT or SURR connection

Audio connecting cords (Red and White) (supplied)

White (L)

CENTER or SUB WOOFER connection

Audio connecting cords (Black) (supplied)

Black

Notes

• When you make the Multi-channel connection, connect the ANALOG 2CH OUT jacks also using another audio connecting cord so that you can play a CD (or SACD) when you set the input selector of your amplifier to CD (or SACD) input .

• During playback of a conventional CD or a 2CH Super Audio CD, no signal is output from the ANALOG 5.1CH FRONT L/R jacks. Instead, the signal is output in high quality from the ANALOG 2CH OUT jacks (see page 7). (SCD-XA777ES only)

• During playback of a conventional CD or a 2CH Super Audio CD, the same signal that is output from the ANALOG 2CH OUT jacks is also output from the ANALOG 5.1CH FRONT L/ R jacks. (SCD-XA333ES only)

• During playback of a Multi-channel Super Audio CD, no signal is output from the ANALOG 2CH OUT jacks. (SCD-XA777ES only)

• During playback of a Multi-channel Super Audio CD, the same signal that is output from the ANALOG 5.1CH FRONT L/R jacks is also output from the ANALOG 2CH OUT jacks. (The down mixed signal of the Multi-channel signal is not played back.) (SCD-XA333ES only)

• There are 5CH, 4CH, and 3CH Super Audio CD. When you play these disc, the signal does not output from all the jacks of the ANALOG 5.1CH OUT. For details of the playback, see the cover or instructions of the Super Audio CD.

Getting Started

Red (R)

To FRONT IN jacks (L/R)

FRONT SURROUND SUB WOOFER

ANALOG

To SURROUND or REAR IN jacks (L/R)

CENTER

5.1CH OUT

2CH OUT

Red (R)

DIGITAL(CD)

OPTICALCOAXIAL

OUT

To CENTER IN jack

AC IN

This illustration is for SCD-XA777ES. For SCDXA333ES, connect the same jacks of SCDXA777ES (see page 10).

To SUB WOOFER IN jack

Multi-channel amplifier, AV amplifier, etc.

Hooking Up the Audio Components

Getting Started

Connecting via ANALOG 2CH OUT jacks

Use an audio connecting cords for this connection. Connect the ANALOG 2CH OUT L/R jacks to the CD (SACD) input jacks of your amplifier. Be sure to match the colour-coded pin to the appropriate jacks: white (left) to white and red (right) to red.

SCD-XA777ES

Audio connecting cords (Red and White) (supplied)

White (L)

Red (R)

SCD-XA333ES

Audio connecting cords (Red and White) (not supplied*)

White (L)

Red (R)

* If you do not make the ANALOG 5.1 CH connection (page 5),

you can use the supplied audio connecting cable for the ANALOG 2CH connection.

White (L)

Red (R)

White (L)

Red (R)

Notes

• During playback of a Multi-channel Super Audio CD, no signal is output from the ANALOG 2CH OUT jacks. (SCD-XA777ES only)

About the ANALOG 2CH OUT (SCDXA777ES only)

When you play a conventional CD or a 2CH Super Audio CD, the stereo signal is sent to the FRONT, SURROUND, and CENTER/ SUB WOOFER D/A Converters, and each signal is combined after D/A conversion, then combined signal is output from the 2CH OUT jacks. Since each digital signal is converted to analog signal by three converters, this system offers a three-fold improvement in a signal quality and a root three-fold in noise ratio, and results in improvement in a signal to noise ratio. Therefore, the high quality signal is output from the ANALOG 2CH OUT jacks. However, because of the system, no signal is output from the ANALOG 2CH OUT jacks during playback of a Multi-channel Super Audio CD. Similarly, no signal is output from the PHONES jack during playback of a Multi-channel Super Audio CD.

FRONT SURROUND SUB WOOFER

To CD (SACD) IN jacks (L/R)

CENTER

ANALOG

5.1CH OUT

2CH OUT

OUT

DIGITAL(CD)

OPTICALCOAXIAL

AC IN

This illustration is for SCD-XA777ES. For SCDXA333ES, connect the same jacks of SCDXA777ES (see page 10).

Stereo amplifier, etc.

Connecting via DIGITAL (CD) OUT OPTICAL connector

Use an optical digital cable for this connection. When connecting the optical digital cable to the DIGITAL (CD) OUT OPTICAL connector, take the cap off the connectors and push the cable plugs in until they click into place. Be careful not to bend or twist the optical cable.

Optical digital cable (not supplied)

Note

Only the audio signals of conventional CDs can be output from the DIGITAL (CD) OUT connectors. Those of the Super Audio CD cannot be output through DIGITAL (CD) OUT.

Note on the ANALOG output jacks (SCD-XA777ES only)

This player is equipped with a Tri-Powered D/A Converter System and a Multi Channel Management function. The usable output settings differ depending on the mode you select as follows. For details, refer to the Operating Instructions.

Source

Super Audio CD

(2 channel)

Super Audio CD

(Multi-channel)

Multi Channel Managment

Not available when playing back CDs

Direct

2ch + SW

Direct

Except Direct

2CH OUT jacks

× × ×

5.1CH OUT jacks

PHONES jack

× × ×

Getting Started

Connecting via DIGITAL (CD) OUT COAXIAL connector

Use a coaxial digital cable to connect the audio components equipped with coaxial digital input connectors.

Coaxial digital cable (not supplied)

Note

Only the audio signals of conventional CDs can be output from the DIGITAL (CD) OUT connectors. Those of the Super Audio CD cannot be output through DIGITAL (CD) OUT.

Connecting the mains lead (SCD-XA333ES only)

Connect the mains lead to a wall outlet.

Connecting the mains lead (SCD-XA777ES only)

Connect the supplied mains lead to the AC IN terminal on the player and to the mains.

Note on 2 channel playback of Super Audio CDs

If you select “2ch + SW,” the output setting becomes 3 channel and the playback sound is output from the 5.1 CH OUT jacks. Therefore, no sound is output from the 2 CH OUT jacks or PHONES jack.

Location and Functions of Parts

This chapter tells you about the location and functions of the various buttons and controls on the front and rear panels and the supplied remote. Further details are provided on the pages indicated in parentheses. It also tells you about the information that appears in the display window.

Front Panel Parts Descriptions

1 POWER switch (14)

Press to turn on the player.

2 Remote sensor

3 Disc tray (14)

Press A OPEN/CLOSE to open/close the disc tray.

4 A OPEN/CLOSE button (14)

Press to open the disc tray.

5 PHONES

Connect the headphones.

For SCD-XA777ES

During playback of a Multi-channel Super Audio CD, no signal of the Multi-channel signal is output from the PHONES jack (see page 7).

For SCD-XA333ES

During playback of a Multi-channel Super Audio CD, the same signal that is output from the ANALOG

5.1CH FRONT L/R jacks is output from the PHONES jack.

6 PHONE LEVEL

Adjust the headphones volume.

(4)

SCD-XA777ES

POWER

PHONE LEVEL

MIN MAX

PHONES

SCD-XA333ES

TIME/TEXT SACD/CD

MULTI/2CHMENU

OPEN/CLOSE

Location and Functions of Parts

AMS

PUSH ENTER

POWER

PHONE LEVEL

MIN MAX

PHONES

TIME/TEXT SACD/CD

MULTI/2CHMENU

7 TIME/TEXT button (15)

Each time you press the button, the playing time of the track, the total remaining time on the disc, or TEXT information appears in the display.

8 MENU (13)

Press to enter the menu.

9 MULTI/2CH button (with an LED) (14)

Each time you press the button while the 2 channel + Multi-channel Super Audio CD (page 13) is loaded, the playback area changes between the multi-channel playback area (the LED turns on) and 2 channel playback area (the LED turns off).

0 SACD/CD button (with an LED) (14)

Each time you press the button while the Hybrid disc (page 13) is loaded, the layer changes between the HD layer (the LED turns on) and CD layer (the LED turns off).

qa Display window (15)

Shows various information.

OPEN/CLOSE

AMS

PUSH ENTER

qs N button (14)

Press to start play.

N indicator

Lights up during playback.

qd X button (14)

Press to pause play.

X indicator

Lights up during pause.

qf x button (14)

Press to stop play.

qg l AMS L dial (AMS: Automatic Music Sensor)

(18)

When you turn the l AMS L dial counterclockwise by one click, you go back to the preceding track; when you turn the l AMS L dial clockwise by one click, you go to the succeeding track.

Rear Panel Parts Descriptions

ANALOG

2CH OUT 5.1CH OUT OUT

FRONT

COAXIAL OPTICAL

SURR CENTER

SUB

WOOFER

DIGITAL(CD)

SCD-XA777ES

Location and Functions of Parts

SCD-XA333ES

FRONT SURROUND SUB WOOFER

ANALOG

CENTER

5.1CH OUT

2CH OUT

OUT

DIGITAL(CD)

OPTICALCOAXIAL

AC IN

1 ANALOG 5.1CH OUT jacks (5)

Connect to an amplifier equipped with the 5.1CH input jacks (Multi-channel amplifier, AV amplifier, etc.) using the audio connecting cords.

2 DIGITAL (CD) OUT COAXIAL connector (7)

Connect to an audio component using the coaxial digital cable.

3 DIGITAL (CD) OUT OPTICAL connector (7)

Connect to an audio component using an optical digital cable.

4 AC IN terminal (7)

Connect the mains lead.

5 ANALOG 2CH OUT L/R jacks (6)

Connect to an audio component (stereo/2 channel) using the audio connecting cord.

Note

Only the audio signals of the CD can be output from the DIGITAL (CD) OUT connectors shown in 2 and 3. Those of the Super Audio CD cannot be output through DIGITAL (CD) OUT.

Remote Parts Descriptions

1 CONTINUE button (20)

Press to resume normal play from Shuffle Play or Programme Play.

SHUFFLE button (20)

Press to select Shuffle Play.

PROGRAM button (21)

Press to select Programme Play.

2 DISPLAY MODE button (16)

Press to turn off the information.

3 TIME/TEXT button (15)

Each time you press the button, the playing time of the track, the total remaining time on the disc, or TEXT information appears in the display.

4 Number buttons (18)

Press to enter the track numbers.

10 button (18)

Press to locate a track numbered over 10.

6 REPEAT button (19)

Press repeatedly to play all tracks or only one track on the disc.

7 AyB button (20)

Press to select Repeat A-B Play.

8 H button (14)

Press to start play.

X button (14)

Press to pause play.

x button (14)

Press to stop play.

9 AMS ./> (AMS: Automatic Music Sensor)

buttons (18)

Press to locate a specific track.

0 m/M buttons (18)

Press to locate a portion you want to play within a track.

qs SACD/CD button (14)

Each time you press the button, ”SACD“ or ”CD“ appears in the display. Select the type of CD you want to play.

qd MULTI/2CH button (14)

Press to select the playback area when the 2 channel + Multi-channel Super Audio CD (page 13) is loaded.

qf ENTER button (25)

Press to decide the selection.

qg CLEAR button (21)

Press to delete a programmed track number.

qh LEVEL ADJ button (25)

Press to adjust the output level balance for the Multichannel management function (page 23).

qj CHECK button (21)

Press to check the programmed order.

PLAY MODE

CONTINUE SHUFFLE

DISPLAY/

MODE

TIME/TEXT

PROGRAM

SACD/CD

MULTI/2CH

123 456

10/0

CHECK

CLEAR

LEVEL

ADJ

>10 ENTER

REPEAT

Location and Functions of Parts

qa INDEX >/. buttons (18)

Press to locate a specific point marked with an index signal when you play a disc that has index signals.

AMS

INDEX

Playing Discs

Compatible Disc Types

This chapter explains the various ways to play discs.

You can play the following discs with this player. Depending on the type of disc to be played, select the appropriate indicator by pressing SACD/CD or MULTI/ 2CH (pages 14).

Classification by the layer configuration

Super Audio CD (single layer disc)

This disc consists of a single HD (high density) layer. When you play this disc, the player is set to the Super Audio CD playback mode automatically.

HD (Super Audio CD) layer

Super Audio CD (dual layer disc)

This disc consists of dual HD layers and is capable of extended play over long periods. When you play this disc, the player is set to the Super Audio CD playback mode automatically. Also, as the dual layer disc consists of dual HD layers on one side only, it is not necessary to turn the disc over.

HD (Super Audio CD) layer

Conventional CD

This disc is the standard format. When you play this disc, the player is set to the Conventional CD playback mode automatically.

CD layer

Super Audio CD + CD (Hybrid disc)

This disc consists of an HD layer and a CD layer. Press SACD/CD to select the layer you want to listen to. Also, as the dual layers are on one side, it is not necessary to turn the disc over. You can play the CD layer using a conventional CD player.

2 channel + Multi-channel Super Audio CD

This disc consists of the 2 channel playback area and the multi-channel playback area. Press MULTI/2CH to select the playback area you want to listen to.

2 channel playback area

CD layer

HD (Super Audio CD) layer

Classification by the channel configuration of the Super Audio CD

2 channel Super Audio CD

This disc consists of the 2 channel playback area. When you play this disc, the player is set to the 2 channel playback mode automatically.

2 channel playback area

Multi-channel Super Audio CD

This disc consists of the multi-channel playback area. When you play this disc, the player is set to the multichannel playback mode automatically.

Multi-channel playback area

Selecting the default playback area (2 channel playback or multi-channel playback area)

1 During stop mode, press MENU. 2 Tur n l AMS L until “M/2CH SELECT” appears

in the display.

3 Press l AMS L.

The current playback area appears.

4 Tur n l AMS L to select desired playback area,

then press l AMS L.

Incompatible Discs

This player cannot play the following discs. If you try to play them, the error message “TOC Error” or “No Disc” will appear or there will be no sound.

• CD-ROM

• DVD, etc.

Playing Discs

Multi-channel playback area

Playing a Disc

The operations for normal play and the basic operations during play are explained below.

SCD-XA777ES

POWER

SCD-XA333ES

Playing Discs

POWER

1 Turn on the amplifier. Turn down the volume level

to the lowest.

2 Select the player position using the input selector

on the amplifier.

3 Press POWER to turn on the player. 4 Press A OPEN/CLOSE to open the disc tray, and

place a disc on the tray.

A OPEN/CLOSEN

SACD/CD lAMSL

lAMSL

SACD/CD

A OPEN/CLOSE N

Basic operations during play

To Press

Stop play x

Pause play X

Resume play after pausing X or N

Locate a succeeding track Turn lAMSL clockwise

Locate the beginning of the Turn lAMSL current track or a preceding counterclockwise track

Eject the disc A OPEN/CLOSE

If you turn on the player when a disc is already loaded

Playback starts automatically. If you connect a commercially available timer, you can set it to start playing the disc at any time you want.

To select a layer you want to listen to when playing a hybrid

disc (page 13)

After you stop play using x, press SACD/CD repeatedly to light either the “SACD” or “CD.”

To select a playback area you want to listen to when playing

a 2 channel + Multi-channel Super Audio CD (page 13)

After you stop play using x, press MULTI/2CH repeatedly to light either the “MULTI CH” or “2 CH.”

Note

During playback, increase the volume level gradually starting from the lowest level. The output from this unit may contain band width that are out of the normal listening range. This may cause damage to the speakers or ears.

With the label side up

5 Press SACD/CD to select the SACD or CD.

Each time you press the button, the SACD or CD appears alternately in the display. Select the type of disc on the tray. For details, see page 12.

6 Press N.

Playback starts from the first track. If you want to start playing from a specific track, turn lAMSL to select the track number before pressing N.

7 Adjust the volume on the amplifier.

Using the Display

4 9

SUPER AUDIO

MULTI 5.1 CH

1234 6789

16 17 18 1

4 9

1234 6789

16 17 18 1

The display window shows various information about the disc or track being played. This section describes the current disc information and information that appears for each play status.

SCD-XA777ES

TIME/TEXT

lAMSL

SCD-XA333ES

lAMSL

Disc information when a disc is loaded

Depending on the disc that is currently loaded, the display shows as follows:

2 channel Super Audio CD

SUPER AUDIO

Multi-channel Super Audio CD

During playback a 5.1 channel Super Audio CD

Conventional CD

2CH

123 678

16 17 18 1

SUPER AUDIO

MULTI 5 CH

During playback a 5 channel Super Audio CD

123 678

16 17 18 1

SUPER AUDIO

MULTI CH

During playback other Super Audio CDs or during stop mode

123 678

16 17 18 1

Playing Discs

TIME/TEXT

DISPLAY MODE

TIME/TEXT

Displaying information while the player is stopped

Press TIME/TEXT.

The display shows the total number of tracks and total playing time,.

Total number of tracks

TRACK DISC MIN SEC

10 45.28

Total playing time

SUPER AUDIO

MULTI CH

12345 678910

16 17 18 19 20

Using the Display

Displaying information while the player is playing

Press TIME/TEXT.

Each time you press the button, the current track number and its elapsed time or remaining time appears, or the total remaining time for the disc appears in the display. When the player detects a Multi-channel Super Audio CD, the channel information appears before the default display appears.

Playing track number and elapsed playing time of the current track (default display)

Playing Discs

111.57

Playing track number and remaining time of the current track

1-1.56

Total remaining time on the disc

-43.32

Channel information (appears only when the player detects a Multi-channel Super Audio CD)

[MULTI] 5.1 CH

Turning off the information in the display

Each time you press DISPLAY MODE on the remote while playing a disc, the display turns off and on alternately. Even when the display is turned off, the display turns on if you pause or stop play. When you resume play, the display turns off again. Before you start playing, when you press DISPLAY MODE to turn off the display, “Display Off” appears, and when you press the button to turn on the display, “Display On” appears.

TRACK MIN SEC

INDEX

Press TIME/TEXT

TRACK MIN SEC

Press TIME/TEXT

MIN SEC

Press TIME/TEXT

TRACK

SUPER AUDIO

MULTI 5.1 CH

SUPER AUDIO

MULTI 5.1 CH

SUPER AUDIO

MULTI 5.1 CH

SUPER AUDIO

MULTI 5.1 CH

12345 678910

16 17 18 19 20

12345 678910

16 17 18 19 20

12345 678910

16 17 18 19 20

12345 678910

16 17 18 19 20

Displaying the information of a TEXT disc

TEXT discs contain information, such as the disc name or artist name, as well as the audio signals. This player can display the disc name, artist name, and current track name as TEXT information. When the player detects a TEXT disc, “TEXT” appears in the display. If your TEXT disc has several languages, “TEXT” and “MULTI” appear in the display. When you want to check the information in another language, see “Displaying the information of a TEXT disc in other languages” on page 17.

Displaying the information of a TEXT disc in stop mode

Press TIME/TEXT.

Each time you press the button, the disc name or artist name appears in the display. When you select the artist name, “ARTIST” appears in the display.

• Before you start playing

Disc title

TEXT DISC

SONYHITS 

SUPER AUDIO

MULTI CH

Press TIME/TEXT

Artist name

TEXT ARTIST

SONY BAND 

SUPER AUDIO

MULTI CH

Press TIME/TEXT

Total number of tracks and total playing time

TEXT TRACK MIN SEC

10 45.28

SUPER AUDIO

MULTI CH

12345 678910

16 17 18 19 20

12345 678910

16 17 18 19 20

12345 678910

16 17 18 19 20

Press TIME/ TEXT

Display information of a TEXT disc while playing a disc

Displaying the information of a TEXT disc in other languages

The current track name appears. If the disc name has more than 15 characters, the first 14 characters will remain after the name scrolls by in the display. When the player detects a Multi-channel Super Audio CD, the channel information appears before the playing time of the current track appears.

• While playing a disc

Track title

TEXT TRACK

HITECHBLUES 

SUPER AUDIO

MULTI 5.1 CH

Press TIME/TEXT

Channel information (appears only when the player detects a Multi-channel Super Audio CD)

TRACK

[MULTI] 5.1 CH

SUPER AUDIO

MULTI 5.1 CH

Playing time of the current track

TEXT TRACK MIN SEC

INDEX

111.56

SUPER AUDIO

MULTI 5.1 CH

Press TIME/TEXT

12345 678910

16 17 18 19 20

12345 678910

16 17 18 19 20

12345 678910

16 17 18 19 20

You can change the displayed language if the TEXT disc has multi language capacity. When the player detects such a TEXT disc, “TEXT” and “MULTI” appear in the display. Change the language according to the procedures below.

1 Press MENU in stop mode. 2 Tur n l AMS L until “LANGUAGE” appears in

the display.

3 Press l AMS L.

The current selected language (English, French, German, etc.) flashes. If the player cannot display the language used in a TEXT disc, “Other Lang” appears in the display.

4 Tur n l AMS L until the desired language

appears in the display.

5 Press l AMS L.

After a few seconds, the information appears in the selected language.

Playing Discs

Remaining time on the current track

TEXT TRACK MIN SEC

1-1.57

SUPER AUDIO

MULTI 5.1 CH

12345 678910

16 17 18 19 20

Press TIME/TEXT

Remaining time on the disc

TEXT MIN SEC

 -43.32

SUPER AUDIO

MULTI 5.1 CH

12345 678910

16 17 18 19 20

Press TIME/ TEXT

Notes

• The display may not show all the characters, depending on the disc.

• This player can display only the disc name, artist name, and track names from TEXT discs. Other information cannot be displayed.

Locating a Specific Track

During stop or play mode, you can locate any track to be played.

Locating a Particular Point in a Track Z

You can locate a particular point in a track during play or play pause.

SCD-XA777ES

SCD-XA333ES

Playing Discs

To locate

The next or succeeding tracks

The current or preceding tracks

A specific track directly

Locating a track directly by entering the track number Z

Press the number button(s) to enter the track number.

lAMSL

You need to

Turn l AMS L clockwise until you find the track. When using the remote, press > repeatedly until you find the track.

Turn l AMS L counterclockwise until you find the track. When using the remote, press . repeatedly until you find the track.

Turn l AMS L until you find the track number you want. When using the remote, press . or > repeatedly until you find the track.

Number buttons

>10

./>

m/M

INDEX

>/.

Locating a point while monitoring the sound (Search)

Press and hold m/M during play.

You will hear intermittent playback as the disc goes forward or reverses. When you reach the desired point, release the button.

Locating a point by observing the time indication (High-Speed Search)

Press and hold m/M during play pause.

You will not hear the playback sound.

When “Over!!” appears in the display

The disc has reached its end. Press . or m to go back.

Note

Tracks that are only a few seconds long may be too short for monitoring. In this case, the player may not search correctly.

To enter a track number over 11

1 Press >10. 2 Enter the corresponding digits.

To enter 0, press 10/0 instead.

Examples:

• To play track number 30, press >10, then 3 and 10/0.

• To play track number 100, press >10 twice, then 1, and 10/0 twice.

Locating a point using the index function (Index Search)

Press INDEX. or INDEX> repeatedly in play or pause mode.

What is an INDEX?

Some SACD or CD are provided with an index marking system which divides tracks or discs into smaller segments. This is especially useful when you want to locate a certain point within a long track (in classical music for example). The index search function works only when you use a commercially available indexed discs (usually indicated on the label).

Locating a point by setting the start time (Time Search)

1 Press ./> to select the desired track in stop

mode.

2 Press and hold m/M to set the time to start play

while looking at the display.

You can set the time from the beginning of the desired track when you press M at first, and set the time from the end of the desired track backward’s when you press m at first.

Playing Tracks Repeatedly

You can play an entire disc or portions thereof repeatedly. This function can be used with Shuffle Play to repeat all the tracks in random order (page 20), or with Programme Play to repeat all the tracks in a programme (page 21). You can also repeat a specific track or portion within a track.

TRACK MIN SEC

52.57

3 Press H.

Play will start at the time search.

SUPER AUDIO

MULTI 5.1 CH

12345 678910

16 17 18 19 20

REPEAT

AyB

Note

If you turn off the player or disconnect the mains lead, the player will store the last setting of repeat play (“Repeat All” or “Repeat 1”) and recall it the next time you turn on the player. However, the setting of the Repeat A-B Play will be cancelled if you turn off the player or disconnect the mains lead.

Repeating all the tracks on the disc (Repeat All Play)

Press REPEAT once, then press H.

“REPEAT” appears in the display and Repeat All Play starts. The repeat play changes depending on the play mode you select.

Playing Discs

When the play mode is

Normal play (page 14)

Shuffle Play (page 20)

Programme Play (page 21)

The player repeats

All the tracks in sequence

All the tracks in random order

All the tracks in the programme in sequence

To stop Repeat All Play

Press x.

To resume normal play

Press REPEAT repeatedly until “REPEAT” goes off.

Playing Tracks Repeatedly Z

Playing Tracks in Random Order (Shuffle Play) Z

Repeating the current track (Repeat 1 Play)

While the track you want to repeat is being played, press REPEAT repeatedly until “REPEAT 1” appears in the display.

Repeat 1 Play starts.

To stop Repeat 1 Play

Press x.

To resume normal play

Press REPEAT repeatedly until “REPEAT 1” goes off.

Playing Discs

Repeating a specific portion within a track (Repeat A-B Play)

You can specify one portion within a track to be played repeatedly. Note that the portion that you specify must be within the boundaries of a single track.

1 While the player is playing, press AyB at the

starting point (point A) of the portion to be played repeatedly.

“REPEAT” appears and “A” flashes in the display.

When you select Shuffle Play, the player plays all the tracks on the disc in random order.

CONTINUE

./>

SHUFFLE

2 Continue playing the track (or press M) to locate

the ending point (point B), then press AyB.

“REPEAT A-B” appears and Repeat A-B Play starts.

To stop Repeat A-B Play and resume normal play

Press REPEAT or x.

You can set a new starting point and ending point during

Repeat A-B Play

You can change the current ending point to a new starting point, then specify a new ending point to repeat another portion right after the current portion. 1 During Repeat A-B Play, press AyB.

The current ending point changes to the new starting point (point A). “REPEAT” lights up and “A” flashes in the display.

2 Locate the new ending point (point B) and press AyB.

“REPEAT A-B” lights up and the player starts to repeat the

newly specified portion. When you want to restart from the starting point A, press H during AyB repeat.

1 Press SHUFFLE in stop mode. 2 Press H.

Shuffle Play starts. “;” appears while the player is “shuffling” the tracks. The player will stop after playing all the tracks once.

To resume normal play

Press CONTINUE.

You can locate tracks during Shuffle Play

Press ./>.

Press > to locate the next track or press . to locate the beginning of the current track. The player does not go back to tracks which have already been played.

Creating Your Own Programme (Programme Play) Z

You can pick out the tracks that you like and specify the playback order in a programme containing up to 32 tracks (or 999 min. 59 sec. in total programme time)

CONTINUE

Number buttons

>10

CHECK

PROGRAM

CLEAR

./>

1 Press PROGRAM in stop mode.

“PROGRAM” appears in the display.

2 Press the number buttons to enter the track

number.

Checking the contents of the programme

Before you start playing or while the player is playing, press CHECK.

Each time you press the button, the track numbers will appear in the display in the programmed order. When you press CHECK while the player is playing, the track number appears from the current track number.

Changing the contents of the programme

You can change the contents of the programme in stop mode.

Erase a track

Erase from the last track in the programme

Add a track to the end of the programme

Erase all tracks

Do the following:

1 Press CHECK repeatedly until the track

number you want to erase appears.

2 Press CLEAR.

Press CLEAR. Each time you press the button, the last track of the programme is erased.

Press ./> to select the track you want to add, then press PROGRAM. When using the remote, press the number button of the track to be added.

Hold down CLEAR (for about 2 seconds) until ”Prog CLEAR“ appears in the display.

Playing Discs

If you entered the wrong track number

Press CLEAR to erase the track number and reenter the correct track number using the number buttons.

To select a track number over 11

Press >10 (page 18).

3 Repeat step 2 to enter other tracks.

Each time you enter a track number, the total programme time appears in the display.

4 Press H.

Programme Play starts.

To resume normal play

Press CONTINUE.

The programme remains even after Programme Play ends

Press H to play from the beginning of the programme again. The programme remains even if you stop play.

Note

If you turn off the player, disconnect the mains lead, or press A OPEN/CLOSE, the programme will be erased.

Listening to a CD Using a

Setting the DIGITAL OUT on/

Filter (Digital Filter Function)

This player is equipped with a digital filter that eliminates noise generated during sampling. By selecting type of filters, you can adjust the sound quality. You can select “STANDARD” or “OPTION.” (The default setting is “STANDARD.”)

SCD-XA777ES

Playing Discs

SCD-XA333ES

lAMSL

off

You can set the digital out mode to on (the digital signals can be output) or off (the digital signals cannot be output). When you use the DIGITAL (CD) OUT COAXIAL or DIGITAL (CD) OUT OPTICAL connecter, set the digital mode to on (“D.OUT ON”). (The default setting is ”D.OUT ON.”)

SCD-XA777ES

SCD-XA333ES

lAMSL

1 Press MENU. 2 Tur n l AMS L until “D. FILTER” appears in the

display.

3 Press l AMS L. 4 Tur n l AMS L until desired filter name

(“STANDARD” or “OPTION”) appears in the display.

5 Press l AMS L.

When you select “OPTION,” “FILTER” appears in the display.

Characteristics of each digital filter

STANDARD

Provides a wide frequency range and spatial feeling.

OPTION

Provides smooth and powerful sound with clear image position.

Notes

• Digital filters are effective only when you play a conventional

CD. You cannot select the digital filter when you play a Super

Audio CD.

• According to the disc or connected equipment, there may be no

noticeable effect after switching the filter.

1 Press MENU. 2 Tur n l AMS L until “D. OUTPUT” appears in

the display.

3 Press l AMS L. 4 Tur n l AMS L until desired digital mode

(“D.OUT ON” or “D.OUT OFF”) appears in the display.

5 Press l AMS L.

Note

When you play a Super Audio CD, this function does not work and no signal is output from the DIGITAL (CD) OUT connectors.

Selecting the default playback area

(2 channel playback or multi-channel playback area)

1 During stop mode, press MENU. 2 Tur n l AMS L until “M/2CH SELECT” appears

in the display.

3 Press l AMS L.

The current playback area appears.

4 Tur n l AMS L to select desired playback area,

then press l AMS L.

Listening to a Multichannel Super Audio CD

(Multi-channel management function)

This player is equipped with a Multi-channel management function that sets the playback mode of the Super Audio CD by the DSD-DSP (built into the player) according to the layout or size of your speaker.

Example of the speaker layout

Front speakers

Sub woofer

Surround speakers

Center speaker

To set the Multi-channel management: 1 Select the appropriate preset playback mode (2 channel

playback or Multi-channel playback).

2 Adjust the output level balance of each speaker (only

when you select the Multi-channel playback mode).

Notes

• This features only work when you play the Super Audio CD.

• You may not be able to adjust the output level balance depending on the speaker layout mode that you selected.

SCD-XA777ES

lAMSL

ENTER

LEVEL ADJ

./>

Selecting 2 channel playback mode

1 Press MENU. 2 Tur n l AMS L until “2CH SPK MODE” appears

in the display.

3 Press l AMS L.

The playback mode appears in the display.

Playback mode

2CH Direct

2CH + SW

*1The audio signal is output from the ANALOG 2CH OUT

jacks and no signal is output from the ANALOG 5.1CH FRONT L/R jacks. (SCD-XA777ES only)

*2The audio signal is output from the ANALOG 5.1CH

FRONT L/R jacks and no signal is output from the ANALOG 2CH OUT jacks. (SCD-XA777ES only)

Front speakers

Each signal outputs directly from front speakers. No signal outputs from the Sub woofer.*

Sub woofer

Playing Discs

SCD-XA333ES

lAMSL

4 Tur n l AMS L until desired mode appears in

the display.

5 Press l AMS L.

Note

You cannot operate this function when the player is in the CD or Multi-channel playback mode. Operate this function when the player is in the 2 channel Super Audio CD playback mode, the disc tray is opened, or no discs are in the player.

Selecting Multi-channel playback mode

1 Press MENU. 2 Tur n l AMS L until “MCH SPK MODE”

appears in the display.

Listening to the Multi-channel Super Audio CD

3 Press l AMS L.

The playback mode appears in the display.

Playback mode

MCH Direct

5 – Large + SW

5 – Large

5 – Small + SW

FRT – Large +SW

Playing Discs

FRT – Large

No – CNTR + SW

No – CNTR

About “Large” or “Small” speaker

A “Large” speaker is a speaker that can reproduce bass frequencies plentifully. If you select “Small” for the surround speakers, the bass frequencies will come from the front speakers and/or sub woofer. For normal use, select “MCH Direct” or set all the speakers to “Large” (ex. “5 – Large + SW,” “5 – Large,” etc.). If the sound is noisy or the Multi-channel playback is not effective while playing a Multi-channel Super Audio CD, change the settings of the speakers concerned to “Small.”

4 Tur n l AMS L until desired mode appears in

the display.

5 Press l AMS L.

The output level balance setting display appears. To set the output level balance, go to Step 4 in “Adjusting the output level balance on the front panel of the player” on page 24 or Step 2 in “Adjusting the output level from the remote” on page 25. To return to the normal display, press MENU.

Notes

• The Multi-channel management function does not work when you select “MCH Direct” (you cannot set the output level balance of each speaker).

• The front speaker setting is set to “Large” automatically when you set the Sub woofer to “––.”

• When you play a track that does not contain the LFE* signal, the signal for the Sub woofer does not output. Therefore, when you select “MCH Direct,” “5 – Large + SW,” or “No – CNTR + SW,” no signal outputs from the Sub woofer. However, when you select “5 – Small + SW” or “FRT – Large +SW” (when you set the speaker setting to “Small”), the bass frequencies will come from the sub woofer. * Low Frequency Enhancement (described as “.1 CH”)

––

Surround speakers

Large

Small

Large

Sub

woofer

––

Front

speakers

Each signal outputs directly from each speaker.

Large

Small

Large

Center

speaker

Large

Small

Adjusting the output level balance of each speaker

You can adjust following items with the Multi-channel management function:

CNTR BALANCE

The relative output level balance between the front speakers (FRONT L/R) and the center speaker (CENTER)

SURR BALANCE

The relative output level balance between the front speakers (FRONT L/R) and the surround speakers (SURR L/R)

SW BALANCE

The relative output level balance between the front speakers (FRONT L/R) and the sub woofer (SUB WOOFER)

Note

Some adjustment may not work depending on the Multi-channel playback mode that you selected.

Adjusting the output level balance on the front panel of the player

You can adjust the output level balance of each speaker while listening during playback. You can also adjust while listening to the test tone during stop mode.

1 Press MENU. 2 Tur n l AMS L until “LEVEL ADJUST” appears

in the display.

3 Press l AMS L.

During playback, go to Step 6.

4 Tur n l AMS L until “TONE ON” appears in the

display.

5 Press l AMS L.

The test tone issues from the speakers in sequence with the speaker type appearing in the display.

6 Tur n l AMS L until the desired item appears

in the display.

Select the item from “CNTR BALANCE,” “SURR BALANCE,” or “SW BALANCE.”

Note

When you set the Sub woofer to “––” in the Multi-channel playback mode (page 23), “SW BALANCE” does not appear. Similarly, “CNTR BALANCE” or “SURR BALANCE” does not appear when you set the corresponding speaker to “––.”

7 Press l AMS L.

The balance adjustment display appears. In stop mode, the test tone is output from the selected speaker. Example: When you select “SURR BALANCE”

during stop mode, the test tone is output from the front speakers and surround speakers.

5 Press ENTER.

The balance adjustment display appears. In stop mode, the test tone is output from the selected speaker. Example: When you select “SURR BALANCE”

during stop mode, the test tone is output from the front speakers and surround speakers.

TEXT DISC

FRT:_____:SURR

SUPER AUDIO

MULTI CH

12345 678910

16 17 18 19 20

8 Tu rn l AMS L to adjust the output level.

TEXT DISC

FRT:_____:SURR

SUPER AUDIO

MULTI CH

12345 678910

16 17 18 19 20

9 Press l AMS L.

The player status returns to Step 6. Repeat Step 6 through 9 for more adjustments.

Press MENU after you finish adjusting.

The display returns to the normal display.

Adjusting the output level from the remote Z

You can adjust the output level of each speaker from the listening position by using the supplied remote.

1 Press LEVEL ADJ during playback or stop mode.

During playback, go to Step 4.

2 Press ./> repeatedly until “TONE ON”

appears in the display.

3 Press ENTER.

The test tone issues from the speakers in sequence with the speaker type appearing in the display.

4 Press ./> repeatedly until the desired item

appears in the display.

Select the item from “CNTR BALANCE,” “SURR BALANCE,” or “SW BALANCE.”

Note

TEXT DISC

FRT:_____:SURR

SUPER AUDIO

MULTI CH

12345 678910

16 17 18 19 20

6 Press ./> repeatedly to adjust the output

level.

TEXT DISC

FRT:_____:SURR

SUPER AUDIO

MULTI CH

12345 678910

16 17 18 19 20

7 Press ENTER.

The player status returns to Step 4. Repeat Step 4 through 7 for more adjustments.

8 Press LEVEL ADJ after you finish adjusting.

The display returns to the normal display.

Note

If you select a playback mode other than “2CH Direct” or “MCH Direct” using the Multi-channel management function, the sound distribution to the speakers will change, possibly causing a decrease in overall sound volume. If this occurs, adjust the volume with the volume control on the connected amplifier.

Note on the ANALOG output jacks (SCD-XA777ES only)

Source

Super Audio CD

(2 channel)

Super Audio CD

(Multi-channel)

Multi Channel Managment

Not available when playing back CDs

Direct

2ch + SW

Direct

Except Direct

2CH OUT jacks

× × ×

5.1CH OUT jacks

PHONES jack

× × ×

Playing Discs

Note on 2 channel playback of Super Audio CDs

If you select “2ch + SW,” the output setting becomes 3 channel and the playback sound is output from the 5.1 CH OUT jacks. Therefore, no sound is output from the 2 CH OUT jacks or PHONES jack.

Additional

Precautions

Information

This chapter provides additional information that will help you understand and maintain your Super Audio CD player.

On safety

• Caution — The use of optical instruments with this product will increase eye hazard.

• Should any solid object or liquid fall into the cabinet, unplug the player and have it checked by qualified personnel before operating it any further.

• AC power cord must be changed only at the qualified service shop.

• The unit is not disconnected from the AC power source (mains) as long as it is connected to the wall outlet, even if the unit itself has been turned off.

On power sources

• Before operating the player, check that the operating voltage of the player is identical with your local power supply. The operating voltage is indicated on the nameplate at the rear of the player.

• The player is not disconnected from the mains as long as it is attached to the mains, even if the player itself has been turned off.

• If you are not going to use the player for a long time, be sure to disconnect the player from the mains. To disconnect the mains lead, grasp the plug itself; never pull the cord.

On placement

• Place the player in a location with adequate ventilation to prevent heat build-up in the player.

• Do not place the player on a soft surface such as a rug that might block the ventilation holes on the bottom.

• Do not place the player in a location near heat sources, or in a place subject to direct sunlight, excessive dust or mechanical shock.

On operation

• If the player is brought directly from a cold to a warm location, or is placed in a very damp room, moisture may condense on the lenses inside the player. Should this occur, the player may not operate properly. In this case, remove the disc and leave the player turned on for about an hour until the moisture evaporates.

• During power on, some noise may be heard while the disc is being loaded into the Super Audio CD player. This is not a malfunction.

On adjusting the volume

• Do not turn up the volume too much while listening to a portion with very low level inputs or no audio signals. If you do, the speakers may be damaged when a peak level portion is played.

Notes on Discs

On inserting a disc

• You may hear a transmission or a mechanical sound from the player. This indicates that the player is automatically adjusting its internal mechanisms according to the inserted disc. You may also hear the mechanical sound from the player when you insert a warped disc.

On cleaning

• Clean the cabinet, panel, and controls with a soft cloth slightly moistened with a mild detergent solution. Do not use any type of abrasive pad, scouring powder, or solvent such as alcohol or benzine.

On transportation

• Be sure to remove the disc on the tray.

• Be sure to close the disc tray.

If you have any questions or problems concerning your player, please consult your nearest Sony dealer.

On handling discs

• To keep the disc clean, handle the disc by its edge. Do not touch the surface.

• Do not stick paper or tape on the disc.

• Use only round-shaped discs. If you use a special shaped disc (e.g., star-shaped, heart-shaped, or square-shaped, etc.), the player may be damaged.

• Do not use a disc with a seal attached on such as on a used disc or rental disc.

On keeping discs

• Do not expose the disc to direct sunlight or heat sources such as hot air ducts.

• After playing, store the disc in its case. If you put it on top of another disc without the case , the disc may be damaged.

On placing discs on the disc tray

• Make sure the disc is positioned securely on the tray. If not, the player or the disc may be damaged.

On cleaning

• If the disc is dirty with fingerprints or dust, it may lessen the quality of the audio out.

• Before playing, clean the disc with a cleaning cloth. Wipe the disc from the centre out.

• Clean the disc with a soft cloth slightly moistened with water, and remove moisture with a dry cloth.

• Do not use solvents such as benzine, thinner, record cleaners, or anti-static spray.

Notes on CD-R/CD-RW playback

• Discs recorded on CD-R/CD-RW drives may not be played back because of scratches, dirt, recording condition, or the drive’s characteristics. Besides, the discs, which are not yet finalized at the end of recording, cannot be played back.

Additional Information

Troubleshooting Specifications

If you experience any of the following difficulties while using the player, use this troubleshooting guide to help you remedy the problem. Should any problem persist, consult your nearest Sony dealer.

There is no sound.

, Check that the player is connected securely. , Make sure you operate the amplifier correctly. , When you use the headphones, adjust the volume

with PHONE LEVEL.

There is no sound from the DIGITAL (CD) OUT connectors.

, The audio signals of the super audio CD cannot be

output from the DIGITAL (CD) OUT connectors.

, The digital out mode is set to off. Set the digital

mode to on (see page 22).

The disc does not play.

, There is no disc inside the player. , The disc is placed upside down on the tray. , Place the disc on the disc tray with the label side

up.

, The disc is placed at an angle. Reload the disc. , Clean the disc (see page 27). , Moisture has condensed inside the player. Remove

the disc and leave the player turned on for about an hour.

, There is an incompatible disc on the tray (see page

13).

The remote does not function.

, Remove any obstacles in the path of the remote

and the player.

Point the remote at the remote sensor on the player.

Additional Information

, If the batteries in the remote are weak, replace

with new ones.

If there is no sound only during 2 channel playback of a Super Audio CD.

, Check which mode is selected in Multi-channel

management function of Super Audio CD (2 channel). When the “2CH+ SW” mode is selected, sound is output through the 5.1 CH OUT jacks. For details, see page 23.

There is no sound from the SUB WOOFER jack.

, Select the playback mode so that the Sub woofer is

set to “a” (page 23).

, When you play a track that does not contain the

LFE signal, the signal outputs from the SUB WOOFER jack only when you select “5 – Small + SW” or “FRT – Large + SW” for the Multi-channel playback mode (page 24).

SCD-XA777ES

When a super audio CD is played

Playing frequency range 2 Hz to 100 kHz

Frequency response 2 Hz to 50 kHz (–3 dB)

Dynamic range 108 dB or more

Total harmonic distortion rate

0.0012 % or less

Wow and flutter Value of measurable limit (±0.001 %

W. PEAK) or less

When a CD is played

Frequency response 2 Hz to 20 kHz

Dynamic range 100 dB or more

Total harmonic distortion rate

0.0017 % or less

Wow and flutter Value of measurable limit (±0.001 %

W. PEAK) or less

Output connector

Jack type

ANALOG OUT

DIGITAL (CD) OUT OPTICAL*

DIGITAL (CD) OUT COAXIAL*

PHONES

*Output only the audio signals of the CD

General

Laser Semiconductor laser

Laser radiant power: 5.47 uW at 650 nm

*These output is the value measured at a distance of about 200mm from the objective lens surface on the optical pick-up.

Power requirements 230 V AC, 50/60 Hz

Power consumption 32 W Dimensions (w/h/d) 430 × 130 × 380 mm

Mass (approx.) 16 kg

Supplied accessories

See page 4.

Phono jacks

Square optical output connector

Coaxial output connector

Stereo phone jack

Output level

2 Vrms (at 50 kilohms)

–18 dBm

0.5 Vp-p

10 mW

(SACD: λ = 650 nm) (CD: λ = 780 nm)

Emission duration: continuous

incl. projecting parts

Load impedance

Over 10 kilohms

Light emitting wave length:

( )

660 nm

75 ohms

32 ohms

Design and specifications are subject to change without notice.

Index

SCD-XA333ES

When a super audio CD is played

Playing frequency range 2 Hz to 100 kHz

Frequency response 2 Hz to 50 kHz (–3 dB)

Dynamic range 106 dB or more

Total harmonic distortion rate

0.0015 % or less

Wow and flutter Value of measurable limit (±0.001 %

W. PEAK) or less

When a CD is played

Frequency response 2 Hz to 20 kHz

Dynamic range 100 dB or more

Total harmonic distortion rate

0.0018 % or less

Wow and flutter Value of measurable limit (±0.001 %

W. PEAK) or less

Output connector

Load impedance

Over 10 kilohms

Light emitting wave length:

( )

660 nm

75 ohms

32 ohms

ANALOG OUT

DIGITAL (CD) OUT OPTICAL*

DIGITAL (CD) OUT COAXIAL*

PHONES

Jack type

Phono jacks

Square optical output connector

Coaxial output connector

Stereo phone jack

Output level

2 Vrms (at 50 kilohms)

–18 dBm

0.5 Vp-p

10 mW

Accessories 4 Amplifier (not supplied) 5 AMS (Automatic Music Sensor) 14 ANALOG OUT

2CH 6

5.1CH 5

Area 13

Batteries 4

Cable

Coaxial digital 7 Optical digital 7

Cord

Audio connecting 5

D, E, F, G

DIGITAL (CD) OUT 7 Digital filter 22 Displaying information 15

H, I, J, K

Hooking Up

Audio Components 5 Power 7

*Output only the audio signals of the CD

General

Laser Semiconductor laser

(SACD: λ = 650 nm) (CD: λ = 780 nm) Emission duration: continuous

Laser radiant power: 5.47 uW at 650 nm *These output is the value measured at a distance of about 200mm from the objective lens surface on the optical pick-up.

Power requirements 230 V AC, 50/60 Hz

Power consumption 27 W Dimensions (w/h/d) 430 × 130 × 380 mm

incl. projecting parts

Mass (approx.) 9.5 kg

Supplied accessories

See page 4.

Design and specifications are subject to change without notice.

Layer 12 Locating

a specific track 18 a particular point 18 by entering the track number 18 by observing the time indication (High-speed Search)

18 using the index function (Index Search) 18 while monitoring the sound (Search) 18

M, N

Multi-channel management function 23 Multi-channel Super Audio CD 13

Additional Information

Index

Output level balance 24

P, Q

Pause play 14 Place a disc 14 Playback mode

2 channel 23 Multi-channel 23

Playing

a disc 14 by entering the track number 18 Multi-channel Super Audio CD 23 repeatedly 19 track in random order 20

Programme Play

Checking the contents of the programme 21 Changing the contents of the programme 21 how to create your own programme 21

Remote commander (remote) 11 Repeat

A-B Play 20 All Play 19 1 Play 20

High-speed search 18

Additional Information

Index search 18 Time Search 19

Shuffle Play 20 Super Audio CD 12

T, U, V, W, X, Y, Z

TEXT 16 TOC 13

+ 90 hidden pages