SA-SS888/WS888
SERVICE MANUAL
Ver 1.0 2003. 03
• SA-SS888 is the speaker section in
DAV-S888.
• SA-WS888 is the Active Subwoofer in
DAV-S888.
Photo : SA-WS888
• SA-SS888 is composed of following models.
As service manuals are issued for each component
model, please refer to them.
SA-SS888
Front and Rear Speakers SS-TS551
Center Speaker SS-CT551
SPECIFICATIONS
AEP Model
UK Model
Subwoofer (SA-WS888)
Speaker system Active subwoofer, magnetically shielded
Speaker unit Woofer: 20 cm (8 inches), cone type
Enclosure type Advanced SAW type
Reproduction frequency range 26 Hz – 200 Hz
Amplifier section
Continuous RMS power output 120 W (8 ohms at 20 Hz – 20 kHz, THD 10%)
Inputs
LINE IN Input pin jack
Dimensions (approx.) 230 × 392 × 464 mm (9 1/8 × 15 1/2 × 18 3/8 inches) (w/h/d) incl.
Mass (approx.) 13.2 kg (29 lb 2 oz)
General
Power requirements (Subwoofer)
Power consumption (Subwoofer) 90 W (1 W in standby mode)
Design and specifications are subject to change without notice.
front grille
220 – 230 V AC, 50/60 Hz
MICRO SATELLITE SYSTEM
9-877-206-01
2003C167800-1
© 2003. 03
Sony Corporation
Home Audio Company
Published by Sony Engineering Corporation
1
SA-SS888/WS888
TABLE OF CONTENTS
1. DIAGRAMS
1-1. Circuit Boards Location (SA-WS888)............................ 3
1-2. Printed Wiring Boards (SA-WS888) .............................. 5
1-3. Schematic Diagram (SA-WS888)................................... 6
2. EXPLODED VIEWS
2-1. Front Panel Section (SA-WS888)................................... 7
2-2. Rear Panel Section (SA-WS888) .................................... 8
3. ELECTRICAL PARTS LIST......................................... 9
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY .
2
SA-SS888/WS888
Note on Schematic Diagram:
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1/
specified.
• 2 : nonflammable resistor.
• 5 : fusible resistor.
• C : panel designation.
Note: The components identified by mark 0 or dotted line
with mark 0 are critical for safety.
Replace only with part number specified.
• A : B+ Line.
• B : B– Line.
•Voltage is dc with respect to ground under no-signal
(detuned) condition.
•Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production tolerances.
• Signal path.
F : AUDIO
Note on Printed Wiring Boards:
• X : parts extracted from the component side.
• b : Pattern from the side which enables seeing.
4
W or less unless otherwise
• Semiconductor
Location
Ref. No. Location
D201 I-4
D202 H-4
D303 E-3
D304 E-3
D305 F-6
D306 D-8
D501 C-8
D502 E-8
D503 E-8
D504 E-8
D505 E-8
D506 F-7
D507 E-7
D601 I-7
D602 I-7
D603 J-7
D604 I-7
D605 H-7
D606 G-7
D607 J-9
D701 B-5
D702 C-5
D703 C-5
D704 C-5
D801 E-10
IC101 C-3
IC102 C-2
IC104 C-5
IC201 H-3
IC202 H-1
IC203 H-3
IC204 H-4
IC301 E-2
IC701 B-6
Q101 C-1
Q301 E-3
Q302 E-2
Q303 E-2
Q304 D-2
Q305 D-3
Q306 D-3
Q307 D-3
Q308 E-7
Q309 F-6
Q310 E-6
Q311 E-6
Q401 J-3
Q402 J-3
Q403 J-2
Q404 J-5
Q501 F-7
Q502 E-7
Q601 H-7
Q602 G-7
Q701 B-5
Q702 C-6
Q703 A-7
Q704 A-7
Q705 A-7
4